summaryrefslogtreecommitdiffstats
path: root/drivers/net
AgeCommit message (Collapse)Author
2010-08-09Revert "p54pci: Add PCI ID for SMC2802W"John W. Linville
This reverts commit 5f7aebd845a9d2ed42f36b7333579ec3534b4713. Apparently, that PCI ID data was incorrectly taken from the subsystem information. The actual ID matches another already known ID. Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-08e100/e1000*/igb*/ixgb*: Add missing read memory barrierJeff Kirsher
Based on patches from Sonny Rao and Milton Miller... Combined the patches to fix up clean_tx_irq and clean_rx_irq. The PowerPC architecture does not require loads to independent bytes to be ordered without adding an explicit barrier. In ixgbe_clean_rx_irq we load the status bit then load the packet data. With packet split disabled if these loads go out of order we get a stale packet, but we will notice the bad sequence numbers and drop it. The problem occurs with packet split enabled where the TCP/IP header and data are in different descriptors. If the reads go out of order we may have data that doesn't match the TCP/IP header. Since we use hardware checksumming this bad data is never verified and it makes it all the way to the application. This bug was found during stress testing and adding this barrier has been shown to fix it. The bug can manifest as a data integrity issue (bad payload data) or as a BUG in skb_pull(). This was a nasty bug to hunt down, if people agree with the fix I think it's a candidate for stable. Previously Submitted to e1000-devel only for ixgbe http://marc.info/?l=e1000-devel&m=126593062701537&w=3 We've now seen this problem hit with other device drivers (e1000e mostly) So I'm resubmitting with fixes for other Intel Device Drivers with similar issues. CC: Milton Miller <miltonm@bga.com> CC: Anton Blanchard <anton@samba.org> CC: Sonny Rao <sonnyrao@us.ibm.com> CC: stable <stable@kernel.org> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-08ixgbe: fix build error with FCOE_CONFIG without DCB_CONFIGJohn Fastabend
Building ixgbe without DCB_CONFIG and FCOE_CONFIG will cause a build error. This resolves the build error by wrapping the fcoe.up in CONFIG_IXGBE_DCB ifdefs. Also frames were being priority VLAN tagged even without DCB enabled. This fixes this so that 8021Q priority tags are only added with DCB actually enabled. Reported-by: divya <dipraksh@linux.vnet.ibm.com> Reported-by: Jon Mason <jon.mason@exar.com> Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-07netxen: protect tx timeout recovery by rtnl lockAmit Kumar Salecha
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-06Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
2010-08-06iwlwifi: fix locking assertionsJohannes Berg
spin_is_locked() can return zero on some (UP?) configurations because locks don't exist, and that causes an endless amount of warnings. Use lockdep_assert_held() instead, which has two advantages: 1) it verifies the current task is holding the lock or mutex 2) it compiles away completely when lockdep is not enabled Cc: stable@kernel.org [2.6.34+, maybe only parts of patch] Reported-by: Thomas Meyer <thomas@m3y3r.de> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-06iwlwifi: fix TX tracerJohannes Berg
The TX tracing code copies with the wrong length, which will typically copy too little data. Fix this by using the correct length variable. Cc: stable@kernel.org [2.6.32+] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-05usbnet: remove noisy and hardly useful printkChristian Samsel
With turned on hspa modem (Dell 5530 internal card) and activated usb auto suspend, my system gets up 100 "usbnet_resume has delayed data" per minute. I didnt noticed any pathological behaviour, so just drop this message. if any objections, please at least change it to _DEBUG. Signed-off-by: Christian Samsel <christian.samsel@rwth-aachen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-05rtl8180: avoid potential NULL deref in rtl8180_beacon_workJohn W. Linville
ieee80211_beacon_get can return NULL... Signed-off-by: John W. Linville <linville@tuxdriver.com> Cc: stable@kernel.org
2010-08-05libertas: scan before assocation if no BSSID was givenDan Williams
Fix this leftover TODO from the cfg80211 conversion by doing a scan if cfg80211 didn't pass in the BSSID for us. Since the scan code uses so much of the cfg80211_scan_request structure to build up the firmware command, we just fake one when the scan request is triggered internally. But we need to make sure that internal 'fake' cfg82011 scan request does not get back to cfg82011 via cfg80211_scan_done(). Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-05libertas: fix association with some APs by using extended ratesDan Williams
Some APs get pissy if you don't send the firmware the extended rates in the association request's rates TLV. Found this on a Linksys WRT54G v2; it denies association with status code 18 unless you add the extended rates too. The old driver did this, but it got lost in the cfg80211 conversion. Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-05libertas: get the right # of scanned BSSesDan Williams
Let's actually check the right field in the command response; and if there aren't any reported BSSes, exit early with success. Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04virtio_net: implements ethtool_ops.get_drvinfoRusty Russell
I often use "ethtool -i" command to check what driver controls the ehternet device. But because current virtio_net driver doesn't support "ethtool -i", it becomes the following: # ethtool -i eth3 Cannot get driver information: Operation not supported This patch simply adds the "ethtool -i" support. The following is the result when using the virtio_net driver with my patch applied to. # ethtool -i eth3 driver: virtio_net version: N/A firmware-version: N/A bus-info: virtio0 Personally, "-i" is one of the most frequently-used option, and most network drivers support "ethtool -i", so I think virtio_net also should do. Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (use ARRAY_SIZE) Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-04ppp: make channel_ops conststephen hemminger
The PPP channel ops structure should be const. Cleanup the declarations to use standard C99 format. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-04drivers/net/enic: Use %pUB to format a UUIDJoe Perches
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-04davinci_emac: Fix use after free in davinci_emac_removeStefan Weil
free_netdev finally calls kfree which makes the contents of ndev and priv (private data contained in ndev) invalid. So iounmap should be called before free_netdev. Cc: David S. Miller <davem@davemloft.net> Cc: Chaithrika U S <chaithrika@ti.com> Cc: Sriramakrishnan <srk@ti.com> Cc: Kevin Hilman <khilman@deeprootsystems.com> Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Stefan Weil <weil@mail.berlios.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-04via-velocity: do not use PCI resources before pci_enable_device()Kulikov Vasiliy
IRQ and resource[] may not have correct values until after PCI hotplug setup occurs at pci_enable_device() time. The semantic match that finds this problem is as follows: // <smpl> @@ identifier x; identifier request ~= "pci_request.*|pci_resource.*"; @@ ( * x->irq | * x->resource | * request(x, ...) ) ... *pci_enable_device(x) // </smpl> Signed-off-by: Kulikov Vasiliy <segooon@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-04cxgb4vf: do not use PCI resources before pci_enable_device()Kulikov Vasiliy
IRQ and resource[] may not have correct values until after PCI hotplug setup occurs at pci_enable_device() time. The semantic match that finds this problem is as follows: // <smpl> @@ identifier x; identifier request ~= "pci_request.*|pci_resource.*"; @@ ( * x->irq | * x->resource | * request(x, ...) ) ... *pci_enable_device(x) // </smpl> Signed-off-by: Kulikov Vasiliy <segooon@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-04cxgb3: do not use PCI resources before pci_enable_device()Kulikov Vasiliy
IRQ and resource[] may not have correct values until after PCI hotplug setup occurs at pci_enable_device() time. The semantic match that finds this problem is as follows: // <smpl> @@ identifier x; identifier request ~= "pci_request.*|pci_resource.*"; @@ ( * x->irq | * x->resource | * request(x, ...) ) ... *pci_enable_device(x) // </smpl> Signed-off-by: Kulikov Vasiliy <segooon@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-04Merge branch 'for-next' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial * 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (48 commits) Documentation: update broken web addresses. fix comment typo "choosed" -> "chosen" hostap:hostap_hw.c Fix typo in comment Fix spelling contorller -> controller in comments Kconfig.debug: FAIL_IO_TIMEOUT: typo Faul -> Fault fs/Kconfig: Fix typo Userpace -> Userspace Removing dead MACH_U300_BS26 drivers/infiniband: Remove unnecessary casts of private_data fs/ocfs2: Remove unnecessary casts of private_data libfc: use ARRAY_SIZE scsi: bfa: use ARRAY_SIZE drm: i915: use ARRAY_SIZE drm: drm_edid: use ARRAY_SIZE synclink: use ARRAY_SIZE block: cciss: use ARRAY_SIZE comment typo fixes: charater => character fix comment typos concerning "challenge" arm: plat-spear: fix typo in kerneldoc reiserfs: typo comment fix update email address ...
2010-08-04iwlagn: Improve aggregation failure error messagesAndy Lutomirski
82ca9341763107615a15da6e59b9535d49eb91c3 added scary looking but harmless error messages. Make them clearer and make the actual failure message show up with the same severity as the harmless one. Signed-off-by: Andy Lutomirski <luto@mit.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04rt2x00: do not use PCI resources before pci_enable_device()Kulikov Vasiliy
IRQ and resource[] may not have correct values until after PCI hotplug setup occurs at pci_enable_device() time. The semantic match that finds this problem is as follows: // <smpl> @@ identifier x; identifier request ~= "pci_request.*|pci_resource.*"; @@ ( * x->irq | * x->resource | * request(x, ...) ) ... *pci_enable_device(x) // </smpl> Signed-off-by: Kulikov Vasiliy <segooon@gmail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04wireless: ipw2100: check result of kzalloc()Christoph Fritz
If kzalloc() fails return with -ENOMEM from ipw2100_net_init() which is called by register_netdev. CC: Dan Carpenter <error27@gmail.com> Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04ath9k: fix erased ieee80211_rx_status.mactimeJan Friedrich
ath9k_rx_skb_preprocess nulls rxs and the mactime is never set again - mactime is always 0. This causes problems in IBSS mode. ieee80211_rx_bss_info uses mactime to decide if an IBSS merge is needed. Without this patch the merge is triggered by each beacon received. This can be recognized by the "beacon TSF higher than local TSF - IBSS merge with BSSID" log message accompanying each beacon. This problem was not completely fixed in commit a6d2055b02dde1067075795274672720baadd3ca and is not a stable kernel fix. It is solely intended for wireless-testing. Signed-off-by: Jan Friedrich <jft@dev2day.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04p54pci: Add PCI ID for SMC2802WLarry Finger
The SMC2802W appears to work with p54pci. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Tested-by: David Cozatt <olbrannon@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04ath9k: fix an issue in ath_atx_tid paused flag managementLorenzo Bianconi
I noticed a possible issue in the paused flag management of the ath_atx_tid data structure. In particular, in a noisy environment and under heavy load, I observed that the AGGR session establishment could fail several times consecutively causing values of the paused flag greater than one for this TID (ath_tx_pause_tid is called more than once from ath_tx_aggr_start). Considering that the session for this TID can not be established also after the mac80211 stack calls the ieee80211_agg_tx_operational() since the ath_tx_aggr_resume() lowers the paused flag only by one. This patch also replaces some BUG_ON calls with WARN_ON, as even if these unlikely conditions happen, it's not fatal enough to justify a BUG_ON. Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04ath9k_hw: Fix regulatory CTL index usage for AR9003Luis R. Rodriguez
AR9003 was not relying on the CTL indexes from the EEPROM for capping the max output power. The CTL indexes from the EEPROM provide calibrated limits for output power for each tested and supported frequency. Without this the device operates at a power level which only conforms to the transmit spectrum mask as specified by IEEE Annex I.2.3. The regulatory limit by CRDA is always used but does not provide calibrated values for optimal performance, specially on band edges. Using the calibrated data from the EEPROM ensures the device operates at optimal output power while still ensuring proper regulatory compliance. The device uses the minimum of these tree values, the value from CRDA, the calibrated value from CTL indexex, and the value to conform to the IEEE transmit spectrum mask. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04net: wl12xx: do not use kfree'd memoryKulikov Vasiliy
wl1271_dump() uses cmd after kfree(cmd). Move kfree() just after wl1271_dump(). Signed-off-by: Kulikov Vasiliy <segooon@gmail.com> Acked-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04iwlagn: fix typo in ucode_bt_stats_read debugfsWey-Yi Guy
small typo fix in ucode_bt_stats_read debugfs file Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04iwlwifi: BA scd_flow not match condition detectedWey-Yi Guy
It is a uCode bug which cause the tx queue id not match scd_flow in compressed block ack frame, and it need to be addressed in uCode. Currently, driver will log the information when it happen. Since it is possible happen very often and we do not want to fill the syslog, so don't enable the logging by default. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04iwlwifi: fix compile warningJohannes Berg
When iwlwifi is compiled w/o debug, we get this warning: iwl-agn.c: In function ‘iwlagn_load_firmware’: iwl-agn.c:2014: warning: passing argument 3 of ‘iwl_print_hex_dump’ discards qualifiers from pointer target type iwl-debug.h:73: note: expected ‘void *’ but argument is of type ‘const u8 *’ because the const qualifier is missing in the inline stub. Fix this. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04ath9k_hw: fix a noise floor calibration related race conditionFelix Fietkau
On AR5008-AR9002, other forms of calibration must not be started while the noise floor calibration is running, as this can create invalid readings which were sometimes not even recoverable by any further calibration attempts. This patch also ensures that the result of noise floor measurements are processed faster and also allows the result of the initial calibration on reset to make it into the NF history buffer Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04ath9k_hw: clean up per-channel calibration dataFelix Fietkau
The noise floor history buffer is currently not kept per channel, which can lead to problems when changing channels from a clean channel to a noisy one. Also when switching from HT20 to HT40, the noise floor history buffer is full of measurements, but none of them contain data for the extension channel, which it needs quite a bit of time to recover from. This patch puts all the per-channel calibration data into a single data structure, and gives the the driver control over whether that is used per-channel or even not used for some channels. For ath9k_htc, I decided to keep this per-channel in order to avoid creating regressions. For ath9k, the data is kept only for the operating channel, which saves some space. ath9k_hw takes care of wiping old data when the operating channel or its channel flags change. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04ath9k: prevent calibration during off-channel activityFelix Fietkau
Previously the software scan callback was used to indicate to the hardware, when it was safe to calibrate. This didn't really work properly, because it depends on a specific order of software scan callbacks vs. channel changes. Also, software scans are not the only thing that triggers off-channel activity, so it's better to use the newly added indication from mac80211 for this and not use the software scan callback for anything calibration related. This fixes at least some of the invalid noise floor readings that I've seen in AP mode on AR9160 Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04ath9k_hw: fix analog shift register writes on AR9003Felix Fietkau
Writes to the analog shift registers, which are issues by the initval programming function, require a 100 usec delay (similar to AR9002, but in a different register range). Signed-off-by: Felix Fietkau <nbd@openwrt.org> Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04ath9k: fix a crash in the PA predistortion apply functionFelix Fietkau
When updating the PAPRD table in hardware, PAPRD itself needs to be disabled first, otherwise the hardware can throw a data bus error, which upsets at least some platforms. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04ath9k_hw: fix periodic noise floor calibration on AR9003Felix Fietkau
The periodic noise floor calibration is broken on this chip family, because it keeps triggering a software-filtered noise floor calibration, but never reads the result before uploading the history buffer value to the hardware. Fix this with a call to ath9k_hw_getnf(), just like on AR9002. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04ath9k_hw: clean up and fix initial noise floor calibrationFelix Fietkau
On AR9003 the initial noise floor calibration is currently triggered at the end of the reset without allowing the hardware to update the baseband settings. This could potentially make scans in noisy environments a bit more unreliable, so use the same calibration sequence that is used on AR9002. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04iwlwifi: fix possible recursive locking deadlockJohannes Berg
commit f84b29ec0a1ab767679d3f2428877b65f94bc3ff Author: Johannes Berg <johannes.berg@intel.com> Date: Tue May 18 02:29:13 2010 -0700 iwlwifi: queue user-initiated scan when doing internal scan introduced a potential deadlock because it calls ieee80211_scan_completed() with the priv->mutex held, but mac80211 may call back into iwlwifi which would lead to recursive locking. Move this out from under the mutex. Cc: stable@kernel.org Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1443 commits) phy/marvell: add 88ec048 support igb: Program MDICNFG register prior to PHY init e1000e: correct MAC-PHY interconnect register offset for 82579 hso: Add new product ID can: Add driver for esd CAN-USB/2 device l2tp: fix export of header file for userspace can-raw: Fix skb_orphan_try handling Revert "net: remove zap_completion_queue" net: cleanup inclusion phy/marvell: add 88e1121 interface mode support u32: negative offset fix net: Fix a typo from "dev" to "ndev" igb: Use irq_synchronize per vector when using MSI-X ixgbevf: fix null pointer dereference due to filter being set for VLAN 0 e1000e: Fix irq_synchronize in MSI-X case e1000e: register pm_qos request on hardware activation ip_fragment: fix subtracting PPPOE_SES_HLEN from mtu twice net: Add getsockopt support for TCP thin-streams cxgb4: update driver version cxgb4: add new PCI IDs ... Manually fix up conflicts in: - drivers/net/e1000e/netdev.c: due to pm_qos registration infrastructure changes - drivers/net/phy/marvell.c: conflict between adding 88ec048 support and cleaning up the IDs - drivers/net/wireless/ipw2x00/ipw2100.c: trivial ipw2100_pm_qos_req conflict (registration change vs marking it static)
2010-08-04Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6 * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6: PM / Runtime: Add runtime PM statistics (v3) PM / Runtime: Make runtime_status attribute not debug-only (v. 2) PM: Do not use dynamically allocated objects in pm_wakeup_event() PM / Suspend: Fix ordering of calls in suspend error paths PM / Hibernate: Fix snapshot error code path PM / Hibernate: Fix hibernation_platform_enter() pm_qos: Get rid of the allocation in pm_qos_add_request() pm_qos: Reimplement using plists plist: Add plist_last PM: Make it possible to avoid races between wakeup and system sleep PNPACPI: Add support for remote wakeup PM: describe kernel policy regarding wakeup defaults (v. 2) PM / Hibernate: Fix typos in comments in kernel/power/swap.c
2010-08-04Merge branch 'master' into for-nextJiri Kosina
2010-08-04hostap:hostap_hw.c Fix typo in commentJustin P. Mattock
The patch below fixes a typo in a comment. Signed-off-by: Justin P. Mattock <justinmattock@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2010-08-04Fix spelling contorller -> controller in commentsStefan Weil
Cc: Jiri Kosina <trivial@kernel.org> Cc: linux-kernel@vger.kernel.org Signed-off-by: Stefan Weil <weil@mail.berlios.de> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2010-08-03phy/marvell: add 88ec048 supportCyril Chemparathy
Marvell 88ec048 is a derivative of its 88e1121r device. From the programmer's perspective, the one major difference is the addition of an additional control bit in Page 2 Register 16 - used to control the padding of odd nibble preambles. This patch adds support for this new device, while inheriting as much code as possible from the existing 88e1121r implementation. Signed-off-by: Cyril Chemparathy <cyril@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-03igb: Program MDICNFG register prior to PHY initAlexander Duyck
This patch addresses an issue seen on 82580 in which the MDICNFG register will be reset during a single function reset and as a result we will be unable to communicate with the PHY. To correct the issue, added a call to reset_mdicnfg just prior to the first access of the MDICNFG register in sgnii_uses_mdio. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-03e1000e: correct MAC-PHY interconnect register offset for 82579Bruce Allan
The MAC-PHY interconnect register set on ICH/PCH parts is accessed through a peephole mechanism by writing an offset to a CSR register. The offset for the interconnect's half-duplex control register (which is used in a jumbo frame workaround for 82579) is incorrect. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-03hso: Add new product IDFilip Aben
This patch adds a new product ID to the hso driver. Signed-off-by: Filip Aben <f.aben@option.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-03can: Add driver for esd CAN-USB/2 deviceMatthias Fuchs
This patch adds a driver for esd's USB high speed CAN interface. The driver supports devices with multiple CAN interfaces. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-02Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/e1000e/hw.h net/bridge/br_device.c net/bridge/br_input.c
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2024-11-02 03:38:25 +0000