summaryrefslogtreecommitdiffstats
path: root/drivers/net
AgeCommit message (Collapse)Author
2011-02-08e1000: add support for Marvell Alaska M88E1118R PHYFlorian Fainelli
This patch adds support for Marvell Alask M88E188R PHY chips. Support for other M88* PHYs is already there, so there is nothing more to add than its PHY id. CC: Dirk Brandewie <dirk.j.brandewie@intel.com> Signed-off-by: Florian Fainelli <ffainelli@freebox.fr> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-02-08e1000e: tx_timeout should not increment for non-hang eventsJesse Brandeburg
Currently the driver increments the tx_timeout counter (an error counter) when simply resetting the part with outstanding transmit work pending. This is an unnecessary count of an error, when all we should be doing is just resetting the part and discarding the transmits. With this change the only increment of tx_timeout is when the stack calls the watchdog reset function due to a true Tx timeout. Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Reviewed-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-02-08m68knommu: Remove dependencies on nonexistent M68KNOMMUGeert Uytterhoeven
M68KNOMMU is set nowhere. Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2011-02-07ath9k: Update comments for not parsing DTIM periodMohammed Shafi Shajakhan
Add few comments for not parsing DTIM period from mac80211 Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-07ath5k: Fix fast channel switchingNick Kossifidis
Fast channel change fixes: a) Always set OFDM timings b) Don't re-activate PHY c) Enable only NF calibration, not AGC Signed-off-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-07iwlagn: Re-enable RF_KILL interrupt when downDon Fry
With commit 554d1d027b19265c4aa3f718b3126d2b86e09a08 only one RF_KILL interrupt will be seen by the driver when the interface is down. Re-enable the interrupt when it occurs to see all transitions. Signed-off-by: Don Fry <donald.h.fry@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-07enic: Clean up: Remove support for an older version of hardwareVasanthy Kolluri
Remove support for an older version (A1) of hardware Signed-off-by: Christian Benvenuti <benve@cisco.com> Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com> Signed-off-by: Roopa Prabhu <roprabhu@cisco.com> Signed-off-by: David Wang <dwang2@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-02-07enic: Bug Fix: Reorder firmware devcmds - CMD_INIT and CMD_IG_VLAN_REWRITE_MODEVasanthy Kolluri
Firmware requires CMD_IG_VLAN_REWRITE_MODE be issued before a CMD_INIT. Signed-off-by: Christian Benvenuti <benve@cisco.com> Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com> Signed-off-by: Roopa Prabhu <roprabhu@cisco.com> Signed-off-by: David Wang <dwang2@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-02-07enic: Bug Fix: Fix return values of enic_add/del_station_addr routinesVasanthy Kolluri
Fix enic_add/del_station_addr routines to return appropriate error code when an invalid address is added or deleted. Signed-off-by: Christian Benvenuti <benve@cisco.com> Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com> Signed-off-by: Roopa Prabhu <roprabhu@cisco.com> Signed-off-by: David Wang <dwang2@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-02-07enic: Clean up: Organize devcmd wrapper routinesVasanthy Kolluri
Organize the wrapper routines for firmware devcmds into a separate file. Signed-off-by: Christian Benvenuti <benve@cisco.com> Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com> Signed-off-by: Roopa Prabhu <roprabhu@cisco.com> Signed-off-by: David Wang <dwang2@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-02-07enic: Decouple mac address registration and deregistration from port profile ↵Roopa Prabhu
set operation This patch removes VM mac address registration and deregistration code during port profile set operation. We can delay mac address registration until enic_open. Signed-off-by: Roopa Prabhu <roprabhu@cisco.com> Signed-off-by: David Wang <dwang2@cisco.com> Signed-off-by: Christian Benvenuti <benve@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-02-06bnx2x: Proper netdev->ndo_set_rx_mode() implementation.Vladislav Zolotarov
Completed the bnx2x_set_rx_mode() to a proper netdev->ndo_set_rx_mode implementation: - Added a missing configuration of a unicast MAC addresses list. - Changed bp->dma_lock from being a mutex to a spinlock as long as it's taken under netdev->addr_list_lock now. Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-02-06bnx2x: Duplication in promisc modeVladislav Zolotarov
Prevent packets duplication for frames targeting FCoE L2 ring: packets were arriving to stack from both L2 RSS and from FCoE L2 in a promiscuous mode. Configure FCoE L2 ring to DROP_ALL rx mode, when interface is configured to PROMISC, and to accept only unicast frames, when interface is configured to ALL_MULTI. Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-02-06bnx2x: MTU for FCoE L2 ringVladislav Zolotarov
Always configure an FCoE L2 ring with a mini-jumbo MTU size (2500). To do that we had to move the rx_buf_size parameter from per function level to a per ring level. Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-02-06iwlwifi: fix compiling error with different configurationWey-Yi Guy
When .config has different configuration, it might fail to compile iwlwifi. fix it Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-02-06iwlwifi: remove unnecessary lockingJohannes Berg
This code, and the places that set the variable is_internal_short_scan and the vif pointers are all protected by the mutex, there's no point in locking the spinlock here as well (any more). Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-02-05sis900: Fix mem leak in sis900_rx error pathJesper Juhl
Fix memory leak in error path of sis900_rx(). If we don't do this we'll leak the skb we dev_alloc_skb()'ed just a few lines above when the variable goes out of scope. Signed-off-by: Jesper Juhl <jj@chaosbits.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-02-05benet: Avoid potential null deref in be_cmd_get_seeprom_data()Ajit Khaparde
Found by: Jesper Juhl <jj@chaosbits.net> Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-02-04Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
2011-02-04ath9k: add additional checks for the baseband hang detectionFelix Fietkau
Since even with the latest changes the false positive issue of the baseband hang check is not fully solved yet, additional checks are needed. If the baseband hang occurs, the rx_clear signal will be stuck to high, so we can use the cycle counters to confirm it. With this patch, a hardware reset is only triggered if the baseband hang check returned true three times in a row, with a beacon interval between each check and if the busy time was also 99% or more during the check intervals. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04ath: Fix clearing of secondary key cache entry for TKIPJouni Malinen
All register writes to the key cache have to be done in pairs. However, the clearing of a separate MIC entry with hardware revisions that use combined MIC key layout did not do that with one of the registers. Add the matching register write to the following register to make the KEY4 register write actually complete. This is mostly a fix for a theoretical issue since the incorrect entry that could potentially be left behind in the key cache would not match with received frames. Anyway, better make this code clean the entry correctly using paired register writes. Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04zd1211rw: add useful debug outputJussi Kivilinna
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04zd1211rw: enable NL80211_IFTYPE_APJussi Kivilinna
It should be safe to enable AP-mode now. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04zd1211rw: reset rx urbs after idle period of 30 secondsJussi Kivilinna
RX appears to freeze while idle. Resetting rx-urbs appears to be enough to fix this. Do reset 30 seconds after last rx. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04zd1211rw: reset device when CR_BCN_FIFO_SEMAPHORE freezes in beacon setupJussi Kivilinna
When driver fails to acquire device semaphore lock, device usually freezes soon afterwards. So failing to acquire lock indicates us that not everything is going right in device/fw. So reset device when this happens. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04zd1211rw: add TX watchdog and device resettingJussi Kivilinna
When doing transfers at high speed for long time, tx queue can freeze. So add tx watchdog. TX-watchdog checks for locked tx-urbs and reset hardware when such is detected. Merely unlinking urb was not enough, device have to be reseted. Hw settings are restored so that any open link will stay on after reset. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04zd1211rw: collect driver settings and add function to restore theimJussi Kivilinna
We need HW hard reset later in patchset to reset device after TX-stall. Collect all settings that we have set to driver for later reset and add restore function. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04zd1211rw: lower hw command timeoutsJussi Kivilinna
Device command timeouts are set up very high (1 sec) and this causes AP beacon to lock up for long for example. Checking timeouts on device it's easy to see that 1 sec timeout is not needed, when device fails to response longer timeout doesn't help: [ 473.074419] zd1211rw 1-1:1.0: print_times() Read times: [ 473.175163] zd1211rw 1-1:1.0: print_time() 0 - 10 msec: 1506 [ 473.176429] zd1211rw 1-1:1.0: print_time() 11 - 50 msec: 0 [ 473.177955] zd1211rw 1-1:1.0: print_time() 51 - 100 msec: 0 [ 473.180703] zd1211rw 1-1:1.0: print_time() 101 - 250 msec: 0 [ 473.182101] zd1211rw 1-1:1.0: print_time() 251 - 500 msec: 0 [ 473.183221] zd1211rw 1-1:1.0: print_time() 500 - 1000 msec: 20 [ 473.184381] zd1211rw 1-1:1.0: print_time() 1000 - ... msec: 18 Also vendor driver doesn't use this long timeout. Therefore change timeout to 50msec. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04zd1211rw: change interrupt URB buffer to DMA bufferJussi Kivilinna
As might lower beacon update CPU usage. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04zd1211rw: use stack and preallocated memory for small cmd-buffersJussi Kivilinna
Use stack for allocing small < 64 byte arrays in zd_chip.c and preallocated buffer in zd_usb.c. This might lower CPU usage for beacon setup. v2: - Do not use stack buffers in zd_usb.c as they would be used for urb transfer_buffer. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04zd1211rw: batch beacon config commands togetherJussi Kivilinna
Beacon config function writes beacon to hw one write per byte. This is very slow (usually taking more than 100ms to finish) and causes high CPU usage when in AP-mode (kworker at ~50% on Intel Atom N270). By batching commands together zd_mac_config_beacon() runtime can be lowered to 1/5th and lower CPU usage to saner levels (<10% on Atom). Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04zd1211rw: add beacon watchdog and setting HW beacon more failsafeJussi Kivilinna
When doing tx/rx at high packet rate (for example simply using ping -f), device starts to fail to respond to control messages. On non-AP modes this only causes problems for LED updating code but when we are running in AP-mode we are writing new beacon to HW usually every 100ms. Now if control message fails in HW beacon setup, device lock is kept locked and beacon data partially written. This can and usually does cause: 1. HW beacon setup fail now on, as driver cannot acquire device lock. 2. Beacon-done interrupt stop working as device has incomplete beacon. Therefore make zd_mac_config_beacon() always try to release device lock and add beacon watchdog to restart beaconing when stall is detected. Also fix zd_mac_config_beacon() try acquiring device lock for max 500ms, as what old code appeared to be trying to do using loop and msleep(1). Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04zd1211rw: implement beacon fetching and handling ieee80211_get_buffered_bc()Jussi Kivilinna
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04zd1211rw: let zd_set_beacon_interval() set dtim_period and add AP-beacon flagJussi Kivilinna
Add support for AP-mode beacon. Also disable beacon when interface is set down as otherwise hw will keep flooding NEXT_BCN interrupts. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04zd1211rw: fix ack_pending in filter_ack causing tx-packet ordering problem ↵Jussi Kivilinna
on monitor For reasons not very clear yet to me, filter_ack leaves matching tx-packet pending with 'ack_pending'. This causes tx-packet to be passed back to upper layer after next packet has been transfered and tx-packets might end up coming come out of monitor interface in wrong order vs. rx. Because of this when enable AP-mode, hostapd monitor interface would get packets in wrong order causing problems in WPA association. So don't use mac->ack_pending when in AP-mode. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04zd1211rw: support setting BSSID for AP modeJussi Kivilinna
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04zd1211rw: move set_rts_cts_work to bss_info_changedJussi Kivilinna
As bss_info_changed may sleep, we can as well set RTS_CTS register right away. Keep mac->short_preamble for later use (hw reset). Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04zd1211rw: move set_multicast_hash and set_rx_filter from workers to ↵Jussi Kivilinna
configure_filter Workers not needed anymore since configure_filter may sleep. Keep mac->multicast_hash for later use (hw reset). Signed-off-by: Jussi Kivilinna <jussi.kivilina@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04zd1211rw: fix beacon interval setupJussi Kivilinna
Vendor driver uses CR_BNC_INTERVAL at various places, one is HW_EnableBeacon() that combinies beacon interval with BSS-type flag and DTIM value in upper 16bit of u32. The other one is HW_UpdateBcnInterval() that set_aw_pt_bi() appears to be based on. HW_UpdateBcnInterval() takes interval argument as u16 and uses that for calculations, set_aw_pt_bi() uses u32 value that has flags and dtim in upper part. This clearly seems wrong. Also HW_UpdateBcnInterval() updates only lower 16bit part of CR_BNC_INTERVAL. So make set_aw_pt_bi() do calculations on only lower u16 part of s->beacon_interval. Also set 32bit beacon interval register before reading values from device, as HW_EnableBeacon() on vendor driver does. This is required to make beacon work on AP-mode, simply reading and then writing updated values is not enough at least with zd1211b. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04zd1211rw: add locking for mac->process_intrJussi Kivilinna
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04zd1211rw: cancel process_intr work on zd_chip_disable_int()Jussi Kivilinna
OOPS if worker is running and disconnect() is called (triggered by unpluging device). Much harder to trigger at this stage but later when we have AP beacon work in process_intr it happens very easy. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04zd1211rw: use urb anchors for tx and fix tx-queue disablingJussi Kivilinna
When stress testing AP-mode I hit OOPS when unpluging or rmmodding driver. It appears that when tx-queue is disabled, tx-urbs might be left pending. These can cause ehci to call non-existing tx_urb_complete() (after rmmod) or uninitialized/reseted private structure (after disconnect()). Add skb queue for submitted packets and unlink pending urbs on zd_usb_disable_tx(). Part of the problem seems to be usb->free_urb_list that isn't always working as it should, causing machine freeze when trying to free the list in zd_usb_disable_tx(). Caching free urbs isn't what other drivers seem to be doing (usbnet for example) so strip free_usb_list. Patch makes tx-urb handling saner with use of urb anchors. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (68 commits) net: can: janz-ican3: world-writable sysfs termination file net: can: at91_can: world-writable sysfs files MAINTAINERS: update email ids of the be2net driver maintainers. bridge: Don't put partly initialized fdb into hash r8169: prevent RxFIFO induced loops in the irq handler. r8169: RxFIFO overflow oddities with 8168 chipsets. r8169: use RxFIFO overflow workaround for 8168c chipset. include/net/genetlink.h: Allow genlmsg_cancel to accept a NULL argument net: Provide compat support for SIOCGETMIFCNT_IN6 and SIOCGETSGCNT_IN6. net: Support compat SIOCGETVIFCNT ioctl in ipv4. net: Fix bug in compat SIOCGETSGCNT handling. niu: Fix races between up/down and get_stats. tcp_ecn is an integer not a boolean atl1c: Add missing PCI device ID s390: Fix possibly wrong size in strncmp (smsgiucv) s390: Fix wrong size in memcmp (netiucv) qeth: allow OSA CHPARM change in suspend state qeth: allow HiperSockets framesize change in suspend qeth: add more strict MTU checking qeth: show new mac-address if its setting fails ...
2011-02-04ath9k: Fix possible double free of PAPRD skb'sMohammed Shafi Shajakhan
This patch reverts the following commit ath9k: remove bfs_paprd_timestamp from struct ath_buf_state Under high interference/noisy environment conditions where PAPRD frames fails heavily introduces a possibility of double freeing skb's and causes kernel panic after some time.This patch reverts back to the original approach of using paprd_timestamp before freeing the PAPRD frame skb's [ 194.193705] Pid: 0, comm: swapper Tainted: G D WC 2.6.35-22-generic #33-Ubuntu [ 194.193712] Call Trace: [ 194.193722] [<c05c6468>] ? printk+0x2d/0x35 [ 194.193732] [<c05c63c3>] panic+0x5a/0xd2 [ 194.193741] [<c05ca3ed>] oops_end+0xcd/0xd0 [ 194.193750] [<c0105f74>] die+0x54/0x80 [ 194.193758] [<c05c9a16>] do_trap+0x96/0xc0 [ 194.193837] [<c0103fb0>] ? do_invalid_op+0x0/0xa0 [ 194.193846] [<c010403b>] do_invalid_op+0x8b/0xa0 [ 194.193856] [<c020bd4c>] ? kfree+0xec/0xf0 [ 194.193866] [<c012ce18>] ? default_spin_lock_flags+0x8/0x10 [ 194.193877] [<c01de47a>] ? free_one_page+0x12a/0x2d0 [ 194.193888] [<c01e04dc>] ? __free_pages+0x1c/0x40 [ 194.193897] [<c05c97a7>] error_code+0x73/0x78 [ 194.193906] [<c020bd4c>] ? kfree+0xec/0xf0 [ 194.193915] [<c04ecdd0>] ? skb_release_data+0x70/0xa0 [ 194.193924] [<c04ecdd0>] skb_release_data+0x70/0xa0 [ 194.193933] [<c04ec997>] __kfree_skb+0x17/0x90 [ 194.193941] [<c04eca31>] consume_skb+0x21/0x40 [ 194.193964] [<f85e0b70>] ieee80211_tx_status+0x760/0x860 [mac80211] [ 194.193979] [<f85caddf>] ath_tx_complete_buf+0x1bf/0x2c0 [ath9k] [ 194.193988] [<c05c8b9f>] ? _raw_spin_lock_irqsave+0x2f/0x50 [ 194.193997] [<c04ec40e>] ? skb_queue_tail+0x3e/0x50 [ 194.194010] [<f85cc803>] ath_tx_complete_aggr+0x823/0x940 [ath9k] [ 194.194021] [<c0108a28>] ? sched_clock+0x8/0x10 [ 194.194030] [<c016bf14>] ? sched_clock_local+0xa4/0x180 [ 194.194040] [<c0139f57>] ? enqueue_sleeper+0x1e7/0x2b0 [ 194.194051] [<c013a194>] ? enqueue_entity+0x174/0x200 [ 194.194064] [<f85ce83d>] ath_tx_edma_tasklet+0x2bd/0x3b0 [ath9k] [ 194.194074] [<c05c8b9f>] ? _raw_spin_lock_irqsave+0x2f/0x50 [ 194.194088] [<f85c7b9f>] ath9k_tasklet+0x9f/0x190 [ath9k] [ 194.194097] [<c01505d7>] tasklet_action+0xa7/0xb0 [ 194.194107] [<c015127c>] __do_softirq+0x9c/0x1b0 [ 194.194117] [<c01a7f64>] ? irq_to_desc+0x14/0x20 [ 194.194126] [<c0124fc4>] ? ack_apic_level+0x64/0x1f0 [ 194.194136] [<c01513d5>] do_softirq+0x45/0x50 [ 194.194145] [<c0151545>] irq_exit+0x65/0x70 [ 194.194153] [<c05cf665>] do_IRQ+0x55/0xc0 [ 194.194162] [<c016a6c7>] ? hrtimer_start+0x27/0x30 [ 194.194171] [<c0103630>] common_interrupt+0x30/0x38 [ 194.194181] [<c012c21a>] ? native_safe_halt+0xa/0x10 [ 194.194268] [<c010a2f9>] default_idle+0x49/0xb0 [ 194.194277] [<c0101fcc>] cpu_idle+0x8c/0xd0 [ 194.194286] [<c05b2431>] rest_init+0x71/0x80 [ 194.194295] [<c081981a>] start_kernel+0x36e/0x374 [ 194.194305] [<c08199dd>] ? pass_all_bootoptions+0x0/0xa [ 194.194314] [<c08190d7>] i386_start_kernel+0xd7/0xdf [ 194.194364] panic occurred, switching back to text console Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04carl9170: fix typo in PS codeChristian Lamparter
This patch fixes a off-by-one bug which bugged the driver's PS-POLL capability. Cc: <stable@kernel.org> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04net: can: janz-ican3: world-writable sysfs termination fileVasiliy Kulikov
Don't allow everybody to set terminator via sysfs. Signed-off-by: Vasiliy Kulikov <segoon@openwall.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-02-04net: can: at91_can: world-writable sysfs filesVasiliy Kulikov
Don't allow everybody to write to mb0_id file. Signed-off-by: Vasiliy Kulikov <segoon@openwall.com> Acked-by: Kurt Van Dijck <kurt.van.dijck@eia.be> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-02-04Merge commit 'v2.6.38-rc3' into devicetree/nextGrant Likely
2011-02-04r8169: prevent RxFIFO induced loops in the irq handler.Francois Romieu
While the RxFIFO interruption is masked for most 8168, nothing prevents it to appear in the irq status word. This is no excuse to crash. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Cc: Ivan Vecera <ivecera@redhat.com> Cc: Hayes <hayeswang@realtek.com>
2011-02-04r8169: RxFIFO overflow oddities with 8168 chipsets.Francois Romieu
Some experiment-based action to prevent my 8168 chipsets locking-up hard in the irq handler under load (pktgen ~1Mpps). Apparently a reset is not always mandatory (is it at all ?). - RTL_GIGA_MAC_VER_12 - RTL_GIGA_MAC_VER_25 Missed ~55% packets. Note: - this is an old SiS 965L motherboard - the 8168 chipset emits (lots of) control frames towards the sender - RTL_GIGA_MAC_VER_26 The chipset does not go into a frenzy of mac control pause when it crashes yet but it can still be crashed. It needs more work. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Cc: Ivan Vecera <ivecera@redhat.com> Cc: Hayes <hayeswang@realtek.com>
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2025-06-30 06:20:46 +0000