| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (109 commits)
PCI: fix coding style issue in pci_save_state()
PCI: add pci_request_acs
PCI: fix BUG_ON triggered by logical PCIe root port removal
PCI: remove ifdefed pci_cleanup_aer_correct_error_status
PCI: unconditionally clear AER uncorr status register during cleanup
x86/PCI: claim SR-IOV BARs in pcibios_allocate_resource
PCI: portdrv: remove redundant definitions
PCI: portdrv: remove unnecessary struct pcie_port_data
PCI: portdrv: minor cleanup for pcie_port_device_register
PCI: portdrv: add missing irq cleanup
PCI: portdrv: enable device before irq initialization
PCI: portdrv: cleanup service irqs initialization
PCI: portdrv: check capabilities first
PCI: portdrv: move PME capability check
PCI: portdrv: remove redundant pcie type calculation
PCI: portdrv: cleanup pcie_device registration
PCI: portdrv: remove redundant pcie_port_device_probe
PCI: Always set prefetchable base/limit upper32 registers
PCI: read-modify-write the pcie device control register when initiating pcie flr
PCI: show dma_mask bits in /sys
...
Fixed up conflicts in:
arch/x86/kernel/amd_iommu_init.c
drivers/pci/dmar.c
drivers/pci/hotplug/acpiphp_glue.c
|
|
If we stop the kthread, we may end up up'ing the sem twice, which seems
unintended.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
The existing interface only has a pre-order callback. This change
adds an additional parameter for a post-order callback which will
be more useful for bus scans. ACPICA BZ 779.
Also update the external calls to acpi_walk_namespace.
http://www.acpica.org/bugzilla/show_bug.cgi?id=779
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Enabling power fault detected event notification in current pciehp
might cause power fault interrupt storm on some machines. On those
machines. On those machines, power fault detected bit in the slot
status register was set again immediately when it is cleared in the
interrupt service routine, and next power fault detected interrupt was
notified again. Therefore, disable power fault detected event
notification for now.
This patch also removes unnecessary handling for power fault cleared
event because this event is not supported by PCIe spec.
Tested-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Change for PCI hotplug to use pci_is_pcie() instead of checking
pci_dev->is_pcie.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Use pci_pcie_cap() instead of pci_find_capability() to get PCIe capability
offset in pciehp driver. This avoids unnecessary search in PCI
configuration space. This patch also removes 'cap_base' field in
struct controller, that was used to hold PCIe capability offset by
pciehp itself.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Use pci_pcie_cap() instead of pci_find_capability() to get PCIe capability
offset in PCI hotplug core. This avoids unnecessary search in PCI
configuration space.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
If firmware doesn't grant over native hotplug control through ACPI
_OSC method, we must not evaluate OSHP.
Acked-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Using list_for_each_entry instead of list_for_each allows us to
enhance readability and minorly reduce some stack usage.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
This patch moves PCI I/O APIC support from acpiphp to a separate driver.
Like pciehp and shpchp, acpiphp handles PCI hotplug, i.e., addition and
removal of PCI adapters. But in addition, acpiphp handles some ACPI
hotplug, such as the addition of new host bridges, and the I/O APIC
support was tangled up with that.
I don't think the I/O APIC support needs to be in acpiphp; PCI I/O APICs
usually appear as a function on a PCI host bridge, and we'll enumerate the
APIC before any of the devices behind the bridge that use it.
As far as I know, nobody actually uses I/O APIC hotplug. It depends on
acpi_register_ioapic(), which is only implemented for ia64, and I don't
think any vendors have supported I/O chassis hotplug yet.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
CC: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
CC: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Prevent unnecessary power off at initialization time. If slot power
is already off, we don't need to power off the slot.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Fix typo that might cause memory leak in pciehp_probe().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Current pciehp returns successfully on read/write failure with dummy
state values. It should return error instead.
With this patch, pciehp no longer uses hotplug_slot_info data
structure. So this also removes hotplug_slot_info related code. But
note that it still allocates hotplug_slot_info because it is required
by pci hotplug core.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Current pciehp driver creates 'attention' and 'latch' files even if
the controller doesn't support them. In this case, the contents of
those files are meaningless and unpredictable. Those files should be
created only if the controller has the corresponding capabilities.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Remove wrong workaround for BAD DLLP error, which confused surprise
down error with DLL errors.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Current pciehp doesn't handle Data Link Layer State Changed Event
notification. So it needs to be disabled at initialization time,
otherwise other event notifications are not generated.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
As a followup to 71a082efc9fdc12068a3cee6cebb1330b00ebeee, it's conceivable
that some vendors may expose PCI hotplug functionality through both vendor
mechanisms and ACPI. The native mechanism will generally be a superset of
any functionality provided via ACPI, so the acpiphp driver should always
be initialised after any others. Change the link order such that acpiphp
will not be initialised until any other statically linked drivers have had
an opportunity to claim the hardware.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Change PCI nomenclature according to
http://www.pcisig.com/developers/procedures/logos/Trademark_and_Logo_Usage_Guidelines_updated_112206.pdf.
Signed-off-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Commit d43c36dc6b357fa1806800f18aa30123c747a6d1 ("headers: remove
sched.h from interrupt.h") left some build errors in some configurations
due to drivers having depended on getting header files "accidentally".
Signed-off-by: Ingo Molnar <mingo@elte.hu>
[ Combined several one-liners from Ingo into one single patch - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 15b8dd53f5ffa changed info->hardware_id from a static array to
a pointer. If hardware_id is non-NULL, it points to a NULL-terminated
string, so we don't need to terminate it explicitly. However, it may
be NULL; in that case, we *can't* add a NULL terminator.
This causes a NULL pointer dereference oops for devices without _HID.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
CC: Lin Ming <ming.m.lin@intel.com>
CC: Bob Moore <robert.moore@intel.com>
CC: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (21 commits)
x86/PCI: make 32 bit NUMA node array int, not unsigned char
x86/PCI: default pcibus cpumask to all cpus if it lacks affinity
MAINTAINTERS: remove hotplug driver entries
PCI: pciehp: remove slot capabilities definitions
PCI: pciehp: remove error message definitions
PCI: pciehp: remove number field
PCI: pciehp: remove hpc_ops
PCI: pciehp: remove pci_dev field
PCI: pciehp: remove crit_sect mutex
PCI: pciehp: remove slot_bus field
PCI: pciehp: remove first_slot field
PCI: pciehp: remove slot_device_offset field
PCI: pciehp: remove hp_slot field
PCI: pciehp: remove device field
PCI: pciehp: remove bus field
PCI: pciehp: remove slot_num_inc field
PCI: pciehp: remove num_slots field
PCI: pciehp: remove slot_list field
PCI: fix VGA arbiter header file
PCI: Disable AER with pci=nomsi
...
Fixed up trivial conflicts in MAINTAINERS
|
|
|
|
Use generic PCIe slot capabilities register definitions instead of
internal definitions.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Remove (almost) unused error message definitions.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Since slot_cap field in struct controller contains physical slot
number informationq, we don't need number field in struct slot.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
The struct hpc_ops seems a set of hooks to controller specific
routines. But, it is meaningless because no hotplug controller driver
follows this framework.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Since we have a pointer to pcie_device in struct controller, we don't
need a pointer to pci_dev.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
The crit_sect mutex defined in struct controller is to serialize
hot-plug operations against multiple slots under the same bus. But,
since PCIe doesnstream port has only one slot at most, it is
meaningless and we don't need it.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Remove unused slot_bus field in struct controller.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
The slot number can be calculated only by physical slot number field
in the slot capabilities register. So the first_slot field in struct
controller is meaningless and we don't need it.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Since the device number of the hot-slot under the PCIe downstream port
is always 0, the slot_device_offset field in the slot is meaningless
and we don't need it.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
The hp_slot field is to identify the slot under the same
controller. But, since PCIe downstream port has only one slot at most,
it is meaningless and we don't need it.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
The device field in the struct slot is not necessary because it is
always 0 in pciehp driver.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
The bus field in struct slot is not necessary.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
The slot_num_inc field in struct controller is unused and meaningless
in pciehp driver.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Since PCIe downstream port has only one slot at most, we don't need
num_slots field in struct controller. Note that struct controller
itself doesn't exist if PCIe downstream port has no slot.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Since PCIe downstream port has only one slot at most, we don't need
'slot_list' linked list to manage multiple slots under the port.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
This patch cleans up acpi_run_hpp() and follows the style of acpi_run_hpx():
- remove unnecessary METHOD_NAME__HPP #define
- use ACPI_ALLOCATE_BUFFER rather than evaluating _HPP twice
- validate _HPP package length (defined as 4 by the spec)
- avoid ref to undefined data if FW provides < 4 elements
- remove temporary nui[] array
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reviewed-by: Alex Chiang <achiang@hp.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Use the generic pci_configure_slot() rather than the acpiphp-specific
decode_hpp() and program_hpp().
Unlike the previous acpiphp-specific code, pci_configure_slot() programs
PCIe settings when an _HPX method provides them, so acpiphp-managed PCIe
devices can now be configured.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Use the generic pci_configure_slot() rather than the SHPC-specific
program_fw_provided_values().
Unlike the previous SHPC-specific code, pci_configure_slot() programs PCIe
settings when an _HPX method provides them, so if it's possible to have an
SHPC-managed PCIe device, it can now be configured.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Use the generic pci_configure_slot() rather than the PCIe-specific
program_fw_provided_values().
Unlike the previous pciehp-specific code, we now walk through subordinate
devices even if there are no settings for the parent. This should be
harmless because we won't change anything unless we discover firmware
settings farther down.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
This patch adds a new pci_configure_slot() function that programs the
PCI bus characteristics for a newly-added device. This is based on
code in pciehp_pci.c, but should be generic enough to be used by pciehp,
shpchp, and acpiphp.
The hotplug_params struct and the program_hpp_typeX() functions are based
on the ACPI definitions, but they aren't really ACPI-specific, and there's
no alternate implementation, so I don't see the need to abstract them yet.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reviewed-by: Alex Chiang <achiang@hp.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
This patch makes acpi_get_hp_params_from_firmware() take a
pci_dev rather than a pci_bus and makes it return a standard
int errno rather than acpi_status.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
We always look up hotplug_params with decode_hpp() immediately before using
them, so we don't need to save them in the acpiphp_bridge struct. This
patch follows the example of program_fw_provided_values() in pciehp_pci.c
and shpchp_pci.c by just keeping the params on the stack while we need them.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reviewed-by: Alex Chiang <achiang@hp.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
decode_hpp() looks up hotplug PCI parameters from ACPI and saves them
in the acpiphp_bridge structure. These parameters (in bridge->hpp) are
only used by the acpiphp_set_hpp_values() -> program_hpp() path. In
that path, we always call decode_hpp() before program_hpp(), so there's
no need to do it in init_bridge_misc().
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reviewed-by: Alex Chiang <achiang@hp.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
acpi_pci_detect_ejectable() goes through effort to convert its
struct pci_bus arg to an acpi_handle, but every time we use this
interface, we already have the handle available.
So let's just use the handle instead of converting back and forth.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Tested-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Instead of constantly evaluating _ADR and _SEG over and over again,
let's simplify our lives by using:
acpi_pci_find_root() for root bridges
acpi_get_pci_dev() for p2p bridges
This change eliminates some copy 'n paste code and also allows us
to simplify some internal interfaces.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Tested-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
There is a very old quirk for the intel E7502 E7320 and E7525 memory
controller hubs that disables usage of msi interrupts on pcie hotplug
bridges of those devices, and disables changing the affinity of irqs.
Today all we have to do to disable msi on a specific device is to set
dev->no_msi, which is much more straightforward than the previous
logic.
The re-running of this fixup after pci hotplug happens below these
devices is totally bogus. All of the state we change is pure software
state and we don't change the hardware at all. Which means hotplug on
the lower devices doesn't have a chance to change this state. So we
can safely remove the special case from the pciehp driver and the pcie
portdriver.
I suspect the special case was someone's expermental debug code that
slipped in. Certainly it isn't mentioned in commit
6fb8880a61510295aece04a542767161f624dffe aka BKrev:
41966101LJ_ogfOU0m2aE6teZfQnuQ where the code first appears.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Add support for PCI-E 5.0 GT/s in max_bus_speed and cur_bus_speed.
Reviewed-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Fix typo in PCI-E link speed.
Reviewed-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
