| Age | Commit message (Collapse) | Author |
|---|
|
Naoki Yanagimoto reported that configuration read on some hot-added
PCIe device returns invalid value. This patch fixes this problem.
According to the PCIe spec, software must wait for at least 1 second
to judge if the hot-added device is broken after Data Link Layer State
Changed Event. This patch changes pciehp driver to wait for 1 second
after the Data Link Layer State Changed Event is detected before
initiating a configuration access instead of 100 ms.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Tested-by: Naoki Yanagimoto <yanagimoto@np.css.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
The function pci_enable_ari() may mistakenly set the downstream port
of a v1 PCIe switch in ARI Forwarding mode. This is a PCIe v2 feature,
and with an SR-IOV device on that switch port believing the switch above
is ARI capable it may attempt to use functions 8-255, translating into
invalid (non-zero) device numbers for that bus. This has been seen
to cause Completion Timeouts and general misbehaviour including hangs
and panics.
Cc: stable@kernel.org
Acked-by: Don Dutile <ddutile@redhat.com>
Tested-by: Don Dutile <ddutile@redhat.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Aside of the usual motivation for constification, this function has a
history of being abused a hook for interrupt and other fixups so I turned
this function const ages ago in the MIPS code but it should be done
treewide.
Due to function pointer passing in varous places a few other functions
had to be constified as well.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
To: Anton Vorontsov <avorontsov@mvista.com>
To: Chris Metcalf <cmetcalf@tilera.com>
To: Colin Cross <ccross@android.com>
Acked-by: "David S. Miller" <davem@davemloft.net>
To: Eric Miao <eric.y.miao@gmail.com>
To: Erik Gilling <konkers@android.com>
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
To: "H. Peter Anvin" <hpa@zytor.com>
To: Imre Kaloz <kaloz@openwrt.org>
To: Ingo Molnar <mingo@redhat.com>
To: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
To: Jesse Barnes <jbarnes@virtuousgeek.org>
To: Krzysztof Halasa <khc@pm.waw.pl>
To: Lennert Buytenhek <kernel@wantstofly.org>
To: Matt Turner <mattst88@gmail.com>
To: Nicolas Pitre <nico@fluxnic.net>
To: Olof Johansson <olof@lixom.net>
Acked-by: Paul Mundt <lethal@linux-sh.org>
To: Richard Henderson <rth@twiddle.net>
To: Russell King <linux@arm.linux.org.uk>
To: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-alpha@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-pci@vger.kernel.org
Cc: linux-sh@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Cc: sparclinux@vger.kernel.org
Cc: x86@kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
The driver reads PCI vendor ID from the PCI configuration register while it is
already stored by the PCI subsystem in the 'vendor' field of 'struct pci_dev'...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
The driver reads PCI subsystem IDs from the PCI configuration registers while
they are already stored by the PCI subsystem in the 'subsystem_{vendor|device}'
fields of 'struct pci_dev'...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
re-scanning PCI
When hot-plugging a root bridge, we always prevent assigning a bus number
that already exists. This makes sure we don't step over an existing bus.
But sometimes we only remove PCI device in PCI hieratchy of OS, i,e.
echo 1 > /sys/bus/pci/devices/.../remove
but actually don't hotplug this device out the platform, so in this case
we still should re-scan this bus to enumerate this device when re-scanning
PCI again.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
In addition to native PCIe AER, now APEI (ACPI Platform Error
Interface) GHES (Generic Hardware Error Source) can be used to report
PCIe AER errors too. To add support to APEI GHES PCIe AER recovery,
aer_recover_queue is added to export the recovery function in native
PCIe AER driver.
Recoverable PCIe AER errors are reported via NMI in APEI GHES. Then
APEI GHES uses irq_work to delay the error processing into an IRQ
handler. But PCIe AER recovery can be very time-consuming, so
aer_recover_queue, which can be used in IRQ handler, delays the real
recovery action into the process context, that is, work queue.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
While it's declared static, etags points you to the wrong function
in drivers/acpi/dock.c and acpiphp_glue.c for example also makes
use of some (exported..) functions from this file.
If you trust etags and oversee the static declaration (what happened
to me) one gets totally confused...
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Multiple attempts to dynamically reallocate pci resources have
unfortunately lead to regressions. Though we continue to fix the
regressions and fine tune the dynamic-reallocation behavior, we have not
reached a acceptable state yet.
This patch provides a interim solution. It disables dynamic reallocation
by default, but adds the ability to enable it through pci=realloc kernel
command line parameter.
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
mmc: queue: bring discard_granularity/alignment into line with SCSI
mmc: queue: append partition subname to queue thread name
mmc: core: make erase timeout calculation allow for gated clock
mmc: block: switch card to User Data Area when removing the block driver
mmc: sdio: reset card during power_restore
mmc: cb710: fix #ifdef HAVE_EFFICIENT_UNALIGNED_ACCESS
mmc: sdhi: DMA slave ID 0 is invalid
mmc: tmio: fix regression in TMIO_MMC_WRPROTECT_DISABLE handling
mmc: omap_hsmmc: use original sg_len for dma_unmap_sg
mmc: omap_hsmmc: fix ocr mask usage
mmc: sdio: fix runtime PM path during driver removal
mmc: Add PCI fixup quirks for Ricoh 1180:e823 reader
mmc: sdhi: fix module unloading
mmc: of_mmc_spi: add NO_IRQ define to of_mmc_spi.c
mmc: vub300: fix null dereferences in error handling
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
x86/PCI/ACPI: fix type mismatch
PCI: fix new kernel-doc warning
PCI: Fix warning in drivers/pci/probe.c on sparc64
|
|
After commit e8665002477f0278f84f898145b1f141ba26ee26
(PM: Allow pm_runtime_suspend() to succeed during system suspend) it
is possible that a device resumed by the pm_runtime_resume(dev) in
pci_pm_prepare() will be suspended immediately from a work item,
timer function or otherwise, defeating the very purpose of calling
pm_runtime_resume(dev) from there. To prevent that from happening
it is necessary to increment the runtime PM usage counter of the
device by replacing pm_runtime_resume() with pm_runtime_get_sync().
Moreover, the incremented runtime PM usage counter has to be
decremented by the corresponding pci_pm_complete(), via
pm_runtime_put_sync().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: stable@kernel.org
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: Compare only lower 32 bits of framebuffer map offsets
drm/i915: Don't leak in i915_gem_shmem_pread_slow()
drm/radeon/kms: do bounds checking for 3D_LOAD_VBPNTR and bump array limit
drm/radeon/kms: fix mac g5 quirk
x86/uv/x2apic: update for change in pci bridge handling.
alpha, drm: Remove obsolete Alpha support in MGA DRM code
alpha/drm: Cleanup Alpha support in DRM generic code
savage: remove unnecessary if statement
drm/radeon: fix GUI idle IH debug statements
drm/radeon/kms: check modes against max pixel clock
drm: fix fbs in DRM_IOCTL_MODE_GETRESOURCES ioctl
|
|
When I added 3448a19da479b6bd1e28e2a2be9fa16c6a6feb39
I forgot about the special uv handling code for this, so this
patch fixes it up.
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Ingo Molnar
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc32, leon: bugfix in LEON SMP interrupt init
sparc32, sun4m: bugfix in SMP IPI traphandler
sparc: Remove unnecessary semicolons
Add support for allocating irqs for bootbus devices
Do not skip interrupt sources in sun4d interrupt handler and acknowledge interrupts correctly
Restructure sun4d_build_device_irq so that timer interrupts can be allocated
sparc: PCIC_PCI needs SPARC32 dependency
sparc: Do not select GENERIC_HARDIRQS_NO_DEPRECATED
sparc32,leon: add GRPCI2 PCI Host driver
sparc32,leon: added LEON-common low-level PCI routines
sparc32: added CONFIG_PCIC_PCI Kconfig setting
|
|
If CONFIG_PM is not set, init_iommu_pm_ops() introduced by commit
134fac3f457f3dd753ecdb25e6da3e5f6629f696 (PCI / Intel IOMMU: Use
syscore_ops instead of sysdev class and sysdev) is not defined
appropriately. Fix this issue.
Reported-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
The LEON architecture does not have a BIOS or bootloader that
initializes PCI for us, instead Linux generic PCI layer is used
to set up resources and IRQ.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* git://git.infradead.org/iommu-2.6:
intel-iommu: Fix off-by-one in RMRR setup
intel-iommu: Add domain check in domain_remove_one_dev_info
intel-iommu: Remove Host Bridge devices from identity mapping
intel-iommu: Use coherent DMA mask when requested
intel-iommu: Dont cache iova above 32bit
intel-iommu: Speed up processing of the identity_mapping function
intel-iommu: Check for identity mapping candidate using system dma mask
intel-iommu: Only unlink device domains from iommu
intel-iommu: Enable super page (2MiB, 1GiB, etc.) support
intel-iommu: Flush unmaps at domain_exit
intel-iommu: Remove obsolete comment from detect_intel_iommu
intel-iommu: fix VT-d PMR disable for TXT on S3 resume
|
|
Fix pci.c kernel-doc warnings:
Warning(drivers/pci/pci.c:3292): No description found for parameter 'flags'
Warning(drivers/pci/pci.c:3292): Excess function parameter 'change_bridge_flags' description in 'pci_set_vga_state'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
We were mapping an extra byte (and hence usually an extra page):
iommu_prepare_identity_map() expects to be given an 'end' argument which
is the last byte to be mapped; not the first byte *not* to be mapped.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
The comment in domain_remove_one_dev_info() states "No need to compare
PCI domain; it has to be the same". But for the si_domain that isn't
going to be true, as it consists of all the PCI devices that are
identity mapped thus multiple PCI domains can be in si_domain. The
code needs to validate the PCI domain too.
Signed-off-by: Mike Habeck <habeck@sgi.com>
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: stable@kernel.org
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
When using the 1:1 (identity) PCI DMA remapping, PCI Host Bridge devices
that do not use the IOMMU causes a kernel panic. Fix that by not
inserting those devices into the si_domain.
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Mike Habeck <habeck@sgi.com>
Cc: stable@kernel.org
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
The __intel_map_single function is not honoring the passed in DMA mask.
This results in not using the coherent DMA mask when called from
intel_alloc_coherent().
Signed-off-by: Mike Travis <travis@sgi.com>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Reviewed-by: Mike Habeck <habeck@sgi.com>
Cc: stable@kernel.org
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Mike Travis and Mike Habeck reported an issue where iova allocation
would return a range that was larger than a device's dma mask.
https://lkml.org/lkml/2011/3/29/423
The dmar initialization code will reserve all PCI MMIO regions and copy
those reservations into a domain specific iova tree. It is possible for
one of those regions to be above the dma mask of a device. It is typical
to allocate iovas with a 32bit mask (despite device's dma mask possibly
being larger) and cache the result until it exhausts the lower 32bit
address space. Freeing the iova range that is >= the last iova in the
lower 32bit range when there is still an iova above the 32bit range will
corrupt the cached iova by pointing it to a region that is above 32bit.
If that region is also larger than the device's dma mask, a subsequent
allocation will return an unusable iova and cause dma failure.
Simply don't cache an iova that is above the 32bit caching boundary.
Reported-by: Mike Travis <travis@sgi.com>
Reported-by: Mike Habeck <habeck@sgi.com>
Cc: stable@kernel.org
Acked-by: Mike Travis <travis@sgi.com>
Tested-by: Mike Habeck <habeck@sgi.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
When there are a large count of PCI devices, and the pass through
option for iommu is set, much time is spent in the identity_mapping
function hunting though the iommu domains to check if a specific
device is "identity mapped".
Speed up the function by checking the cached info to see if
it's mapped to the static identity domain.
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Mike Habeck <habeck@sgi.com>
Cc: stable@kernel.org
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
The identity mapping code appears to make the assumption that if the
devices dma_mask is greater than 32bits the device can use identity
mapping. But that is not true: take the case where we have a 40bit
device in a 44bit architecture. The device can potentially receive a
physical address that it will truncate and cause incorrect addresses
to be used.
Instead check to see if the device's dma_mask is large enough
to address the system's dma_mask.
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Mike Habeck <habeck@sgi.com>
Cc: stable@kernel.org
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Commit a97590e5 added unlinking domains from iommus to reciprocate the
iommu from domains unlinking that was already done. We actually want
to only do this for device domains and never for the static
identity map domain or VM domains. The SI domain is special and
never freed, while VM domain->id lives in their own special address
space, separate from iommu->domain_ids.
In the current code, a VM can get domain->id zero, then mark that
domain unused when unbound from pci-stub. This leads to DMAR
write faults when the device is re-bound to the host driver.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Cc: stable@kernel.org
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
There are no externally-visible changes with this. In the loop in the
internal __domain_mapping() function, we simply detect if we are mapping:
- size >= 2MiB, and
- virtual address aligned to 2MiB, and
- physical address aligned to 2MiB, and
- on hardware that supports superpages.
(and likewise for larger superpages).
We automatically use a superpage for such mappings. We never have to
worry about *breaking* superpages, since we trust that we will always
*unmap* the same range that was mapped. So all we need to do is ensure
that dma_pte_clear_range() will also cope with superpages.
Adjust pfn_to_dma_pte() to take a superpage 'level' as an argument, so
it can return a PTE at the appropriate level rather than always
extending the page tables all the way down to level 1. Again, this is
simplified by the fact that we should never encounter existing small
pages when we're creating a mapping; any old mapping that used the same
virtual range will have been entirely removed and its obsolete page
tables freed.
Provide an 'intel_iommu=sp_off' argument on the command line as a
chicken bit. Not that it should ever be required.
==
The original commit seen in the iommu-2.6.git was Youquan's
implementation (and completion) of my own half-baked code which I'd
typed into an email. Followed by half a dozen subsequent 'fixes'.
I've taken the unusual step of rewriting history and collapsing the
original commits in order to keep the main history simpler, and make
life easier for the people who are going to have to backport this to
older kernels. And also so I can give it a more coherent commit comment
which (hopefully) gives a better explanation of what's going on.
The original sequence of commits leading to identical code was:
Youquan Song (3):
intel-iommu: super page support
intel-iommu: Fix superpage alignment calculation error
intel-iommu: Fix superpage level calculation error in dma_pfn_level_pte()
David Woodhouse (4):
intel-iommu: Precalculate superpage support for dmar_domain
intel-iommu: Fix hardware_largepage_caps()
intel-iommu: Fix inappropriate use of superpages in __domain_mapping()
intel-iommu: Fix phys_pfn in __domain_mapping for sglist pages
Signed-off-by: Youquan Song <youquan.song@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
IO_SPACE_LIMIT is currently used in two ways:
1) As a way to mask I/O port values read out of PCI base address
registers. This value should be 64-bit.
2) As a value which is the upper limit for all I/O "ports" in the
system.
On sparc64 we store the full 64-bit physical I/O address in the
resources. For this reason we define IO_SPACE_LIMIT at a 64-bit
"all 1's".
This is the right value to use for ioport_resource.end and for the
check made in drivers/pcmcia/rsrc_nonstatic.c:adjust_io().
But in driver/pci/probe.c:__pci_read_base() we mask this against
a "u32" variable and thus get the following warning:
drivers/pci/probe.c: In function ¡__pci_read_base¢:
drivers/pci/probe.c:207: warning: large integer implicitly truncated to unsigned type
Fix this by using an explicit "u32" cast.
I considered changing sparc64 to define a 32-bit "all 1's" like
most other systems do, but this wouldn't work because the checks
in PCMCIA's rsrc_nonstatic.c would no longer be right since they
are testing against fully formed 64-bit resources. As described
above, on sparc64 such resources will hold full 64-bit physical
I/O addresses, not bus-centric 32-bit ones.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI EC: remove redundant code
ACPI: Add D3 cold state
ACPI: processor: fix processor_physically_present in UP kernel
ACPI: Split out custom_method functionality into an own driver
ACPI: Cleanup custom_method debug stuff
ACPI EC: enable MSI workaround for Quanta laptops
ACPICA: Update to version 20110413
ACPICA: Execute an orphan _REG method under the EC device
ACPICA: Move ACPI_NUM_PREDEFINED_REGIONS to a more appropriate place
ACPICA: Update internal address SpaceID for DataTable regions
ACPICA: Add more methods eligible for NULL package element removal
ACPICA: Split all internal Global Lock functions to new file - evglock
ACPI: EC: add another DMI check for ASUS hardware
ACPI EC: remove dead code
ACPICA: Fix code divergence of global lock handling
ACPICA: Use acpi_os_create_lock interface
ACPI: osl, add acpi_os_create_lock interface
ACPI:Fix goto flows in thermal-sys
|
|
_SxW returns an Integer containing the lowest D-state supported in state
Sx. If OSPM has not indicated that it supports _PR3, then the value “3”
corresponds to D3. If it has indicated _PR3 support, the value “3”
represents D3hot and the value “4” represents D3cold.
Linux does set _OSC._PR3, so we should fix it to expect that _SxW can
return 4.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (169 commits)
drivers/gpu/drm/radeon/atom.c: fix warning
drm/radeon/kms: bump kms version number
drm/radeon/kms: properly set num banks for fusion asics
drm/radeon/kms/atom: move dig phy init out of modesetting
drm/radeon/kms/cayman: fix typo in register mask
drm/radeon/kms: fix typo in spread spectrum code
drm/radeon/kms: fix tile_config value reported to userspace on cayman.
drm/radeon/kms: fix incorrect comparison in cayman setup code.
drm/radeon/kms: add wait idle ioctl for eg->cayman
drm/radeon/cayman: setup hdp to invalidate and flush when asked
drm/radeon/evergreen/btc/fusion: setup hdp to invalidate and flush when asked
agp/uninorth: Fix lockups with radeon KMS and >1x.
drm/radeon/kms: the SS_Id field in the LCD table if for LVDS only
drm/radeon/kms: properly set the CLK_REF bit for DCE3 devices
drm/radeon/kms: fixup eDP connector handling
drm/radeon/kms: bail early for eDP in hotplug callback
drm/radeon/kms: simplify hotplug handler logic
drm/radeon/kms: rewrite DP handling
drm/radeon/kms/atom: add support for setting DP panel mode
drm/radeon/kms: atombios.h updates for DP panel mode
...
|
|
We typically batch unmaps to be lazily flushed out at
regular intervals. When we destroy a domain, we need
to force a flush of these lazy unmaps to be sure none
reference the domain we're about to free.
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=35062
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@kernel.org
|
|
Since cacd4213d8, this comment no longer applies.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
This patch is a follow on to https://lkml.org/lkml/2011/3/21/239, which
was merged as commit 51a63e67da6056c13b5b597dcc9e1b3bd7ceaa55.
This patch adds support for S3, as pointed out by Chris Wright.
Signed-off-by: Joseph Cihula <joseph.cihula@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (27 commits)
PCI: Don't use dmi_name_in_vendors in quirk
PCI: remove unused AER functions
PCI/sysfs: move bus cpuaffinity to class dev_attrs
PCI: add rescan to /sys/.../pci_bus/.../
PCI: update bridge resources to get more big ranges when allocating space (again)
KVM: Use pci_store/load_saved_state() around VM device usage
PCI: Add interfaces to store and load the device saved state
PCI: Track the size of each saved capability data area
PCI/e1000e: Add and use pci_disable_link_state_locked()
x86/PCI: derive pcibios_last_bus from ACPI MCFG
PCI: add latency tolerance reporting enable/disable support
PCI: add OBFF enable/disable support
PCI: add ID-based ordering enable/disable support
PCI hotplug: acpiphp: assume device is in state D0 after powering on a slot.
PCI: Set PCIE maxpayload for card during hotplug insertion
PCI/ACPI: Report _OSC control mask returned on failure to get control
x86/PCI: irq and pci_ids patch for Intel Panther Point DeviceIDs
PCI: handle positive error codes
PCI: check pci_vpd_pci22_wait() return
PCI: Use ICH6_GPIO_EN in ich6_lpc_acpi_gpio
...
Fix up trivial conflicts in include/linux/pci_ids.h: commit a6e5e2be4461
moved the intel SMBUS ID definitons to the i2c-i801.c driver.
|
|
Don't use the costly dmi_name_in_vendors() when we know the string we
are looking for can only be in the DMI board name field. This is more
robust and, more importantly, much faster.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
In the commit 28eb5f2, aer_osc_setup is removed but corresponding
definiton information in the aerdrv.h is missed.
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Requested by Greg KH to fix a race condition in the creating of PCI bus
cpuaffinity files.
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
After remove the device from /sys, we have to rescan all or
find out the bridge and access /sys../device/rescan there.
this patch add /sys/.../pci_bus/.../rescan. So user can rescan more easy.
that is more clean and easy to understand.
like after remove 0000:c4:00.0, you can rescan 0000:c4 directly.
-v2: According to Jesse, use function instead of exposing attr, so could hide
#ifdef in header file.
also add code to remove rescan file in remove path.
-v3: GregKH pointed out that we should use dev_attrs to avoid racing.
So add pcibus_attrs and make it to be member of pcibus_attrs.
-v4: Change name to pcibus_dev_attrs according to GregKH
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
(again)
With Ram's fixes, this should be safe to do again. So let's give it
another try.
BIOS separates IO ranges between several IOHs, and on some slots, BIOS
assigns resources to a bridge, but stops assigning resources to the
device under that bridge, because the device needs a big resource.
So:
1. allocate resources and record the failed device resources
2. clear the BIOS assigned resources of the parent bridge of failing device
3. go back and call pci assign unassigned
4. if it still fails, go up the tree, clear more bridges. and try again
Now Ram's allocate requested resource already got into mainline. could
put this one again.
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
For KVM device assignment, we'd like to save off the state of a device
prior to passing it to the guest and restore it later. We also want
to allow pci_reset_funciton() to be called while the device is owned
by the guest. This however overwrites and invalidates the struct pci_dev
buffers, so we can't just manually call save and restore. Add generic
interfaces for the saved state to be stored and reloaded back into
struct pci_dev at a later time.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
This will allow us to store and load it later.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Need to use it in _e1000e_disable_aspm. This routine is used for error
recovery, where the pci_bus_sem is already held, and we don't want
pci_disable_link_state to try to take it again. So add a locked variant
for use in cases like this.
Found lock up:
[ 2374.654557] kworker/32:1 D ffff881027f6b0f0 0 6075 2 0x00000000
[ 2374.654816] ffff88503f099a68 0000000000000046 ffff88503f098000 0000000000004000
[ 2374.654837] 00000000001d1ec0 ffff88503f099fd8 00000000001d1ec0 ffff88503f099fd8
[ 2374.654860] 0000000000004000 00000000001d1ec0 ffff88503dcc8000 ffff88503f090000
[ 2374.654880] Call Trace:
[ 2374.654898] [<ffffffff810b1302>] ? __lock_acquired+0x3a/0x224
[ 2374.654914] [<ffffffff81c2b59c>] ? _raw_spin_unlock_irq+0x30/0x36
[ 2374.654925] [<ffffffff810b069d>] ? trace_hardirqs_on_caller+0x1f/0x178
[ 2374.654936] [<ffffffff81c2ab24>] rwsem_down_failed_common+0xd3/0x103
[ 2374.654945] [<ffffffff810b158f>] ? __lock_contended+0x3a/0x2a2
[ 2374.654955] [<ffffffff81c2ab7b>] rwsem_down_read_failed+0x12/0x14
[ 2374.654967] [<ffffffff813371e4>] call_rwsem_down_read_failed+0x14/0x30
[ 2374.654981] [<ffffffff8135df20>] ? pci_disable_link_state+0x5f/0xf5
[ 2374.654990] [<ffffffff81c2a0e6>] ? down_read+0x7e/0x91
[ 2374.654999] [<ffffffff8135df20>] ? pci_disable_link_state+0x5f/0xf5
[ 2374.655008] [<ffffffff8135df20>] pci_disable_link_state+0x5f/0xf5
[ 2374.655024] [<ffffffff81661796>] e1000e_disable_aspm+0x55/0x5a
[ 2374.655037] [<ffffffff816677eb>] e1000_io_slot_reset+0x59/0xea
[ 2374.655048] [<ffffffff8135fe0d>] ? report_mmio_enabled+0x5d/0x5d
[ 2374.655057] [<ffffffff8135fe3b>] report_slot_reset+0x2e/0x5d
[ 2374.655072] [<ffffffff8135369e>] pci_walk_bus+0x8a/0xb7
[ 2374.655081] [<ffffffff8135fe0d>] ? report_mmio_enabled+0x5d/0x5d
[ 2374.655091] [<ffffffff813603be>] broadcast_error_message+0xa4/0xb2
[ 2374.655101] [<ffffffff81352c71>] ? pci_bus_read_config_dword+0x72/0x80
[ 2374.655110] [<ffffffff813606df>] do_recovery+0x9e/0xf9
[ 2374.655120] [<ffffffff81360786>] handle_error_source+0x4c/0x51
[ 2374.655129] [<ffffffff81360974>] aer_isr_one_error+0x1e9/0x21a
[ 2374.655138] [<ffffffff81360a6c>] aer_isr+0xc7/0xcc
[ 2374.655147] [<ffffffff813609a5>] ? aer_isr_one_error+0x21a/0x21a
[ 2374.655159] [<ffffffff81096d9f>] process_one_work+0x237/0x3ec
[ 2374.655168] [<ffffffff81096d10>] ? process_one_work+0x1a8/0x3ec
[ 2374.655178] [<ffffffff8109728d>] worker_thread+0x17c/0x240
[ 2374.655186] [<ffffffff810b0803>] ? trace_hardirqs_on+0xd/0xf
[ 2374.655196] [<ffffffff81097111>] ? manage_workers+0xab/0xab
[ 2374.655209] [<ffffffff8109c8ed>] kthread+0xa0/0xa8
[ 2374.655223] [<ffffffff81c332d4>] kernel_thread_helper+0x4/0x10
[ 2374.655232] [<ffffffff81c2b880>] ? retint_restore_args+0xe/0xe
[ 2374.655243] [<ffffffff8109c84d>] ? __init_kthread_worker+0x5b/0x5b
[ 2374.655252] [<ffffffff81c332d0>] ? gs_change+0xb/0xb
when aer happens,
pci_walk_bus already have down_read(&pci_bus_sem)...
then report_slot_reset
==> e1000_io_slot_reset
==> e1000e_disable_aspm
==> pci_disable_link_state...
We can not use pci_disable_link_state, and it will try to hold pci_bus_sem again.
Try to have __pci_disable_link_state that will not need to hold pci_bus_sem.
-v2: change name to pci_disable_link_state_locked() according to Jesse.
[jbarnes: make sure new function is exported for modules]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core-iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, gart: Rename pci-gart_64.c to amd_gart_64.c
x86/amd-iommu: Use threaded interupt handler
arch/x86/kernel/pci-iommu_table.c: Convert sprintf_symbol to %pS
x86/amd-iommu: Add support for invalidate_all command
x86/amd-iommu: Add extended feature detection
x86/amd-iommu: Add ATS enable/disable code
x86/amd-iommu: Add flag to indicate IOTLB support
x86/amd-iommu: Flush device IOTLB if ATS is enabled
x86/amd-iommu: Select PCI_IOV with AMD IOMMU driver
PCI: Move ATS declarations in seperate header file
dma-debug: print information about leaked entry
x86/amd-iommu: Flush all internal TLBs when IOMMUs are enabled
x86/amd-iommu: Rename iommu_flush_device
x86/amd-iommu: Improve handling of full command buffer
x86/amd-iommu: Rename iommu_flush* to domain_flush*
x86/amd-iommu: Remove command buffer resetting logic
x86/amd-iommu: Cleanup completion-wait handling
x86/amd-iommu: Cleanup inv_pages command handling
x86/amd-iommu: Move inv-dte command building to own function
x86/amd-iommu: Move compl-wait command building to own function
|
|
During pci remove/rescan testing found:
pci 0000:c0:03.0: PCI bridge to [bus c4-c9]
pci 0000:c0:03.0: bridge window [io 0x1000-0x0fff]
pci 0000:c0:03.0: bridge window [mem 0xf0000000-0xf00fffff]
pci 0000:c0:03.0: bridge window [mem 0xfc180000000-0xfc197ffffff 64bit pref]
pci 0000:c0:03.0: device not available (can't reserve [io 0x1000-0x0fff])
pci 0000:c0:03.0: Error enabling bridge (-22), continuing
pci 0000:c0:03.0: enabling bus mastering
pci 0000:c0:03.0: setting latency timer to 64
pcieport 0000:c0:03.0: device not available (can't reserve [io 0x1000-0x0fff])
pcieport: probe of 0000:c0:03.0 failed with error -22
This bug was caused by commit c8adf9a3e873 ("PCI: pre-allocate
additional resources to devices only after successful allocation of
essential resources.")
After that commit, pci_hotplug_io_size is changed to additional_io_size
from minium size. So it will not go through resource_size(res) != 0
path, and will not be reset.
The root cause is: pci_bridge_check_ranges will set RESOURCE_IO flag for
pci bridge, and later if children do not need IO resource. those bridge
resources will not need to be allocated. but flags is still there.
that will confuse the the pci_enable_bridges later.
related code:
static void assign_requested_resources_sorted(struct resource_list *head,
struct resource_list_x *fail_head)
{
struct resource *res;
struct resource_list *list;
int idx;
for (list = head->next; list; list = list->next) {
res = list->res;
idx = res - &list->dev->resource[0];
if (resource_size(res) && pci_assign_resource(list->dev, idx)) {
...
reset_resource(res);
}
}
}
At last, We have to clear the flags in pbus_size_mem/io when requested
size == 0 and !add_head. becasue this case it will not go through
adjust_resources_sorted().
Just make size1 = size0 when !add_head. it will make flags get cleared.
At the same time when requested size == 0, add_size != 0, will still
have in head and add_list. because we do not clear the flags for it.
After this, we will get right result:
pci 0000:c0:03.0: PCI bridge to [bus c4-c9]
pci 0000:c0:03.0: bridge window [io disabled]
pci 0000:c0:03.0: bridge window [mem 0xf0000000-0xf00fffff]
pci 0000:c0:03.0: bridge window [mem 0xfc180000000-0xfc197ffffff 64bit pref]
pci 0000:c0:03.0: enabling bus mastering
pci 0000:c0:03.0: setting latency timer to 64
pcieport 0000:c0:03.0: setting latency timer to 64
pcieport 0000:c0:03.0: irq 160 for MSI/MSI-X
pcieport 0000:c0:03.0: Signaling PME through PCIe PME interrupt
pci 0000:c4:00.0: Signaling PME through PCIe PME interrupt
pcie_pme 0000:c0:03.0:pcie01: service driver pcie_pme loaded
aer 0000:c0:03.0:pcie02: service driver aer loaded
pciehp 0000:c0:03.0:pcie04: Hotplug Controller:
v3: more simple fix. also fix one typo in pbus_size_mem
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Latency tolerance reporting allows devices to send messages to the root
complex indicating their latency tolerance for snooped & unsnooped
memory transactions. Add support for enabling & disabling this
feature, along with a routine to set the max latencies a device should
send upstream.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
OBFF (optimized buffer flush/fill), where supported, can help improve
energy efficiency by giving devices information about when interrupts
and other activity will have a reduced power impact. It requires
support from both the device and system (i.e. not only does the device
need to respond to OBFF messages, but the platform must be capable of
generating and routing them to the end point).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Add support to allow drivers to enable/disable ID-based ordering. Where
supported, ID-based ordering can significantly improve the latency of
individual requests by preventing them from queueing up behind unrelated
traffic.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
