| Age | Commit message (Collapse) | Author |
|---|
|
Add "power-source" property to generic options used for DT parsing files.
This enables drivers, which use generic pin configurations, to get the
value passed to this property.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This issue was reported by coccicheck using the semantic patch
at scripts/coccinelle/api/memdup.cocci
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This commit adds slew-rate and input-enable/disable support for pinconf
-generic.
Signed-off-by: Sherman Yin <syin@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
It does not make sense to show ti prefix in pinconf_generic_dt_subnode_to_map()
dev_err messages.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add support to pass the config type like GROUP or PIN when using
the utils or generic pin configuration APIs. This will make the
APIs more generic.
Added additional inline APIs such that it can be use directly as
callback for the pinctrl_ops.
Changes from V1:
- Remove separate implementation for pins and group for
pinctrl_utils_dt_free_map and improve this function
to support both i.e. PINS and GROUPs.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add generic APIs to map the DT node and its sub node in pinconf generic
driver. These APIs can be used from driver to parse the DT node who
uses the pinconf generic APIs for defining their nodes.
Changes from V1:
- Add generic property for pins and functions in pinconf-generic.
- Add APIs to map the DT and subnode.
- Move common utils APIs to the pinctrl-utils from this file.
- Update the binding document accordingly.
Changes from V2:
- Rebased the pinctrl binding doc on top of Stephen's cleanup.
- Rename properties "pinctrl-pins" and "pinctrl-function" to
"pins" and "function".
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Some options currently take arguments in unspecified driver-specific units.
As pointed out by Stephen Warren, driver specific values should not be part
of generic devicetree bindings describing the hardware.
Therefore remove the critical bindings again, before they become part of
an official release.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Currently the debounce time pinconfig option uses an unspecified
"time units" unit. As pinconfig options should use SI units and a
real unit is also necessary for generic dt bindings, change it
to usec. Currently no driver is using the generic pinconfig option
for this, so the unit change is safe to do.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Allocating the temorary array in pinconf_generic_parse_dt_config on stack
might cause problems later on, when the number of options grows over time.
Therefore also allocate this array dynamically to be on the safe side.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds a shortcut when no valid pinconf properties are found
in the parsed dt node, to set the values immediately and return.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The bias-pull-* options use values > 0 to indicate that the pull should
be activated and optionally also indicate the strength of the pull.
Therefore use an default value of 1 for these options.
Split the low-power-mode option into low-power-enable and -disable.
Update the documentation to describe the param arguments better.
Reported-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
pinconf_generic_parse_dt_config() takes a node as input and generates an
array of generic pinconfig values from the properties of this node.
As I couldn't find a mechanism to count the number of properties of a node
the function uses internally an array to accept one of parameter and copies
the real present options to a smaller variable at its end.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
There exist controllers that don't support to set the pull to up or down
separately but instead automatically set the pull direction based on
embedded knowledge inside the controller, for example depending on the
selected mux function of the pin.
Therefore this patch adds another config option to use this default
pull-state for a pin where it is not possible to know or decide if the
pin will be pulled up or down.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add a new PIN_CONFIG_BIAS_BUS_HOLD pin configuration for a bus holder
pin mode (also known as bus keeper, or repeater). This is a weak latch
which drives the last value on a tristate bus. Another device on the bus
can drive the bus high or low before going tristate to change the value
driven by the pin.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add the drive strength pinconf to debugfs output (with the unit "mA").
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Fixes the following type of checkpatch errors:
ERROR: space required before the open parenthesis '('
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
'conf_items' is used only in this file. Silences the below
sparse warning:
drivers/pinctrl/pinconf-generic.c:37:24: warning:
symbol 'conf_items' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add the support of dumping pin configuration.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Rename PIN_CONFIG_INPUT_SCHMITT_DISABLE to
PIN_CONFIG_INPUT_SCHMITT_ENABLE. It's used to make it more generialize.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add PIN_CONFIG_SLEW_RATE parameter into pinconf-generic driver.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds a definition of a generic output configuration
for a certain pin when using the generic pin configuration
library. Whereas driving pins low/high is usually a GPIO
business, you may want to set up pins into a default state
using hogs, and never touch them again. This helps out
with that scenario.
Based on a patch from Patrice Chotard.
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
In Marvell PXA/MMP silicons, input schmitt disable value is 0x40, not 0.
So append new config parameter -- input schmitt disable.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This is a split-off from the earlier patch set which adds generic
pin configuration for the pin controllers that want it. Since
we may have a system with mixed generic and custom pin controllers,
we pass a boolean in the pin controller ops vtable to indicate
if it is generic.
ChangeLog v1->v5:
- Follow parent patch versioning number system.
- Document the semantic meaning of return values from pin config
get functions, so we can iterate over pins and check their
properties from debugfs as part of the generic config code.
- Use proper cast functions in the generic debugfs pin config
file.
- Expand generic config to optionally cover groups too.
ChangeLog v5->v6:
- Update to match underlying changes.
ChangeLog v6->v7:
- Drop DRIVE_OFF parameter, use bias high impedance for this
- Delete argument for drive modes push-pull, od and os. These
are now just state transitions.
- Delete slew rate rising/falling due to discussions on on
proper semantics
- Drop config wakeup, struct irq_chip does this for now, add
back if need be.
- Set PIN_CONFIG_END to 0x7fff making room for custom config
parameters from 0x8000 and up.
- Prefix accessor functions with pinconf_
|
