| Age | Commit message (Collapse) | Author |
|---|
|
In FC fabrics with large zones, the automatic port_rescan on incoming ELS
and any adapter recovery can cause quite some traffic at the very same
time, especially if lots of Linux images share an HBA, which is common on
s390. This can cause trouble and failures. Fix this by making such port
rescans dependent on a user configurable module parameter.
The following unconditional automatic port rescans remain as is:
On setting an adapter online and
on manual user-triggered writes to the sysfs attribute port_rescan.
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
If the mapping of FCP device bus ID and corresponding subchannel
is modified while the Linux image is suspended, the resume of FCP
devices can fail. During resume, zfcp gets callbacks from cio regarding
the modified subchannels but they can be arbitrarily mixed with the
restore/resume callback. Since the cio callbacks would trigger
adapter recovery, zfcp could wakeup before the resume callback.
Therefore, ignore the cio callbacks regarding subchannels while
being suspended. We can safely do so, since zfcp does not deal itself
with subchannels. For problem determination purposes, we still trace the
ignored callback events.
The following kernel messages could be seen on resume:
kernel: <WWPN>: parent <FCP device bus ID> should not be sleeping
As part of adapter reopen recovery, zfcp performs auto port scanning
which can erroneously try to register new remote ports with
scsi_transport_fc and the device core code complains about the parent
(adapter) still sleeping.
kernel: zfcp.3dff9c: <FCP device bus ID>:\
Setting up the QDIO connection to the FCP adapter failed
<last kernel message repeated 3 more times>
kernel: zfcp.574d43: <FCP device bus ID>:\
ERP cannot recover an error on the FCP device
In such cases, the adapter gave up recovery and remained blocked along
with its child objects: remote ports and LUNs/scsi devices. Even the
adapter shutdown as part of giving up recovery failed because the ccw
device state remained disconnected. Later, the corresponding remote
ports ran into dev_loss_tmo. As a result, the LUNs were erroneously
not available again after resume.
Even a manually triggered adapter recovery (e.g. sysfs attribute
failed, or device offline/online via sysfs) could not recover the
adapter due to the remaining disconnected state of the corresponding
ccw device.
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Cc: <stable@vger.kernel.org> #2.6.32+
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Remove the file name from the comment at top of many files. In most
cases the file name was wrong anyway, so it's rather pointless.
Also unify the IBM copyright statement. We did have a lot of sightly
different statements and wanted to change them one after another
whenever a file gets touched. However that never happened. Instead
people start to take the old/"wrong" statements to use as a template
for new files.
So unify all of them in one go.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
Fix several compile errors on s390 caused by splitting module.h.
Some include additions [e.g. qdio_setup.c, zfcp_qdio.c] are in
anticipation of pending changes queued for s390 that increase
the modular use footprint.
[PG: added additional obvious changes since Heiko's original patch]
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Remove the owner and name members of struct
ccw_driver and convert all drivers to store
this data in the embedded struct device_driver.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
This patch is the final cleanup of the redesign from the zfcp tracing.
Structures and elements which were used by multiple areas of the
former debug tracing are now changed to the new scheme.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Replace the zfcp_modify_<xxx>_status functions and its accompanying wrappers
with dedicated status modifier functions. This eases code readability and
maintenance.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
The steps for setting the zfcp_adapter online are the same in
zfcp_ccw_set_online and zfcp_ccw_activate. Remove the code duplication
by calling zfcp_ccw_activate from zfcp_ccw_set_online.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Kernel code uses dev as short name for the struct device. Rename the
sysfs_device in zfcp_unit and zfcp_port to match this convention.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Move the code for tracking FSF requests to new file to have this code
in one place. The functions for adding and removing requests on the
I/O path are already inline. The alloc and free functions are only
called once, so it does not hurt to inline them and add them to the
same file.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
The flag ZFCP_STATUS_COMMON_REMOVE was used to indicate that a
resource is not ready to be used or about to be removed from the
system. This is now better done by an improved list handling
and therefore the additional indicator is not required anymore.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
With the reference counting for zfcp data structures, it is now
possible to implement module unloading again. Module unloading
requires to free all data structures in the module exit function. This
is done by unregistering zfcp from s390 cio and the SCSI midlayer
first in the module exit function.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
The callback for suspend is not required because it contains exactly
the same functionality as the _set_offline routine does.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
The global config_mutex was required for the serialization of a
configuration change within the zfcp driver. This global locking is
now obsolete and can be removed. The requirement of serializing the
access to a zfcp_adapter reference via a ccw_device is realized wth a
static spinlock.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Replace the local reference counting by already available mechanisms
offered by kref. Where possible existing device structures were used,
including the same functionality.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
The global config_lock was used to protect the configuration organized
in independent lists. It is not necessary to have a lock on driver
level for this purpose. This patch replaces the global config_lock
with a set of local list locks.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Running chchp --vary 0 and chccwdev -d on a FCP device with scsi
devices attached can lead to this thread hanging:
================================================================
STACK TRACE FOR TASK: 0x2fbfcc00 (kslowcrw)
STACK:
0 schedule+1136 [0x45f99c]
1 schedule_timeout+534 [0x46054e]
2 wait_for_common+374 [0x45f442]
3 blk_execute_rq+160 [0x217a2c]
4 scsi_execute+278 [0x26daf2]
5 scsi_execute_req+150 [0x26dc86]
6 sd_sync_cache+138 [0x28460a]
7 sd_shutdown+130 [0x28486a]
8 sd_remove+104 [0x284c84]
9 __device_release_driver+152 [0x257430]
10 device_release_driver+56 [0x2575c8]
11 bus_remove_device+214 [0x25672a]
12 device_del+352 [0x25456c]
13 __scsi_remove_device+108 [0x272630]
14 scsi_remove_device+66 [0x2726ba]
15 zfcp_ccw_remove+824 [0x335558]
16 ccw_device_remove+62 [0x2b3f2a]
17 __device_release_driver+152 [0x257430]
18 device_release_driver+56 [0x2575c8]
19 bus_remove_device+214 [0x25672a]
20 device_del+352 [0x25456c]
21 ccw_device_unregister+92 [0x2b48c4]
22 io_subchannel_remove+108 [0x2b4950]
23 css_remove+62 [0x2af7ee]
24 __device_release_driver+152 [0x257430]
25 device_release_driver+56 [0x2575c8]
26 bus_remove_device+214 [0x25672a]
27 device_del+352 [0x25456c]
28 device_unregister+38 [0x25464a]
29 css_sch_device_unregister+68 [0x2af97c]
30 ccw_device_call_sch_unregister+78 [0x2b581e]
31 worker_thread+604 [0x69eb0]
32 kthread+154 [0x6ff42]
33 kernel_thread_starter+6 [0x1c952]
================================================================
The problem is that the chchp --vary 0 leads to zfcp first calling
fc_remote_port_delete which blocks all scsi devices on the remote
port. Calling scsi_remove_device later lets the sd driver issue a
SYNCHRONIZE_CACHE command. This command stays on the "stopped" request
requeue because the SCSI device is blocked. Fix this by first removing
the scsi and fc hosts which removes all scsi devices and do not use
scsi_remove_device.
Reviewed-by: Felix Beck <felix.beck@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
=======================================================
[ INFO: possible circular locking dependency detected ]
2.6.31-39.x.20090917-s390xdefault #1
-------------------------------------------------------
kslowcrw/83 is trying to acquire lock:
(&adapter->scan_work){+.+.+.}, at: [<0000000000169c5c>] __cancel_work_timer+0x64/0x3d4
but task is already holding lock:
(&zfcp_data.config_mutex){+.+.+.}, at: [<00000000004671ea>] zfcp_ccw_remove+0x66/0x384
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&zfcp_data.config_mutex){+.+.+.}:
[<0000000000189962>] __lock_acquire+0xe26/0x1834
[<000000000018a4b6>] lock_acquire+0x146/0x178
[<000000000058cb5a>] mutex_lock_nested+0x82/0x3ec
[<0000000000477170>] zfcp_fc_scan_ports+0x3ec/0x728
[<0000000000168e34>] worker_thread+0x278/0x3a8
[<000000000016ff08>] kthread+0x9c/0xa4
[<0000000000109ebe>] kernel_thread_starter+0x6/0xc
[<0000000000109eb8>] kernel_thread_starter+0x0/0xc
-> #0 (&adapter->scan_work){+.+.+.}:
[<0000000000189e60>] __lock_acquire+0x1324/0x1834
[<000000000018a4b6>] lock_acquire+0x146/0x178
[<0000000000169c9a>] __cancel_work_timer+0xa2/0x3d4
[<0000000000465cb2>] zfcp_adapter_dequeue+0x32/0x14c
[<00000000004673e4>] zfcp_ccw_remove+0x260/0x384
[<00000000004250f6>] ccw_device_remove+0x42/0x1ac
[<00000000003cb6be>] __device_release_driver+0x9a/0x10c
[<00000000003cb856>] device_release_driver+0x3a/0x4c
[<00000000003ca94c>] bus_remove_device+0xcc/0x114
[<00000000003c8506>] device_del+0x162/0x21c
[<0000000000425ff2>] ccw_device_unregister+0x5e/0x7c
[<000000000042607e>] io_subchannel_remove+0x6e/0x9c
[<000000000041ff9a>] css_remove+0x3e/0x7c
[<00000000003cb6be>] __device_release_driver+0x9a/0x10c
[<00000000003cb856>] device_release_driver+0x3a/0x4c
[<00000000003ca94c>] bus_remove_device+0xcc/0x114
[<00000000003c8506>] device_del+0x162/0x21c
[<00000000003c85e8>] device_unregister+0x28/0x38
[<0000000000420152>] css_sch_device_unregister+0x46/0x58
[<00000000004276a6>] io_subchannel_sch_event+0x28e/0x794
[<0000000000420442>] css_evaluate_known_subchannel+0x46/0xd0
[<0000000000420ebc>] slow_eval_known_fn+0x88/0xa0
[<00000000003caffa>] bus_for_each_dev+0x7e/0xd0
[<000000000042188c>] for_each_subchannel_staged+0x6c/0xd4
[<0000000000421a00>] css_slow_path_func+0x54/0xd8
[<0000000000168e34>] worker_thread+0x278/0x3a8
[<000000000016ff08>] kthread+0x9c/0xa4
[<0000000000109ebe>] kernel_thread_starter+0x6/0xc
[<0000000000109eb8>] kernel_thread_starter+0x0/0xc
cancel_work_sync is called while holding the config_mutex. But the
work that is being cancelled or flushed also uses the config_mutex.
Fix the resulting deadlock possibility by calling cancel_work_sync
earlier without holding the mutex. The best place to do is is after
offlining the device. No new port scan work will be scheduled for the
offline device, so this is a safe place to call cancel_work_sync.
Reviewed-by: Felix Beck <felix.beck@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
With the change that the zfcp_adapter struct is only allocated when
the device is set online, the shutdown handler has to check for a
non-existing zfcp_adapter struct. On the other hand, this check is not
necessary in the offline callback, since an online device has the
zfcp_adapter allocated and we go through the offline callback before
removing the ccw device.
Reviewed-by: Felix Beck <felix.beck@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
With the change for delaying the allocation of zfcp_adapter, the
initial device parameter function has to first call
ccw_device_set_online which allocates the zfcp_adapter structure.
Change this and adapt the cfdc part accordingly.
Reviewed-by: Felix Beck <felix.beck@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
The config semaphore is only used as a mutex, so replace it with a
simple mutex.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
So far, zfcp allocated all resources required for FCP
adapters/subchannels when the device was discovered in the ccw_probe
callback. If there are lots of unused FCP subchannels attached to a
system, this is a waste of resources. To alleviate this, defer the
resource allocation to the first call to ccw_set_online. To avoid
disruptions during possible following calls to ccw_set_offline and
then ccw_set_online, keep the adapter resources until the device is
finally being removed via ccw_remove. While doing this, also manage
the zfcp erp thread together with all other adapter resources in
zfcp_adapter_enqueue/dequeue.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Signed-off-by: Martin Petermann <martin.petermann@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Keep the information about the device and model id in zfcp_ccw. This
requires an additional helper function to check for the privileged
cfdc subchannel, but it allows the removal of the redundant defines
from the zfcp_def header file.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Update the newly introduced message for the boxed status to conform to
match the style of s390 and zfcp messages.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
The nameserver port might be in state online when the adapter is
offlined. On adapter reactivation the nameserver port is not
re-opened due to the PORT_ONLINE status. This results in an
unsuccessful recovery. In forcing the nameserver port status
to offline on all adapter offline events this issue is prevented.
Waiting for the reference count to drop to zero in
zfcp_wka_port_offline is not required, so remove it.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
If a ccw device did not respond in time during internal io, we set it
into boxed state. With this patch we have the following behaviour:
* the ccw driver will get a notification if the device was online and
goes into the boxed state
* if the device was disconnected and got boxed nothing special is to be
done (it will be handled in reprobing later)
* if the device got boxed while initial sensing it will be unregistered
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
A scheduled work might still be pending, running while the adapter is
in progress to get dequeued from the system. This can lead to an
invalid pointer dereference (Oops). Once the adpater is set online
again, ensure the nameserver environment is initialized to the
appropriate values again.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
The current number based id ERP logging is replaced by a string
based tag version. The benefit is an easier location of the code in
question and the removal of the lengthy array referencing the
individual messages.
The string (7 bytes) based version does not use more space since those
bytes were "used" anyway due to the alignment of the structure.
The encoding of the 7 byte string is as follows
[0-1] = filename
[2-5] = task/function
[6] = section
Due to the character of this string (fixed length) a string
termination is not required here.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Use the device pointer in zfcp_unit for tracking if we have a
registered SCSI device. With this approach, the flag
ZFCP_STATUS_UNIT_REGISTERED is only redundant and can be removed.
Acked-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Synchronize the registration and de-registration with the SCSI layer
at CCW registration, de-registration. Before we registered with the
SCSI layer on adapter activation. This way the reg and de-reg process
is in balance.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Attaching a unit immediately after setting the adapter online should
be possible. The problem right now is that the port_scan runs from a
workqueue and has not finished when the set_online call returns and
the sysfs structures for the ports are not available yet. Fix that by
waiting for the port scan to complete.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Reduce the size of zfcp data structures by removing unused and
redundant members. scsi_lun is only the mangled version of the
fcp_lun. So, remove the redundant field and use the fcp_lun instead.
Since the queue lock and the pci_batch indicator are only used in the
request queue, move them from the common queue struct to the adapter
struct.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Call the helper function from cio instead looping through all zfcp
adapters.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
- Remove unused references and declarations, including one instance
of the FC ls_adisc struct that has been defined twice.
- Also remove the flags COMMON_OPENING, COMMON_CLOSING,
ADAPTER_REGISTERED and XPORT_OK that are only set and cleared, but
not checked anywhere.
- Remove the zfcp specific atomic_test_mask makro. Simply use
atomic_read directly instead.
- Remove the zfcp internal sg helper functions and switch the places
where it is still used to call sg_virt directly.
- With the update of the QDIO code, the QDIO data structures no
longer use the volatile type qualifier. Now we can also remove the
volatile qualifiers from the zfcp code.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Update the kernel messages in zfcp with input from the message review
and remove some messages that have been identified as redundant.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
The notify handler does not change the list of adapters, it only
triggers erp actions to open or shutdown the adapter. We don't
need to hold the config semaphore and wait for the erp to complete.
This is a prerequisite for a fix in the s390 common i/o code.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Martin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Overall cleanup of zfcp_aux.c to simplify code and follow kernel
coding style.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Overall cleanup in file zfcp_ccw.c. Fix coding style issues, remove
useless macros and messages and convert remaining messages to standard
macros.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
drivers/s390/scsi/zfcp_aux.c: In function ‘zfcp_fsf_incoming_els_rscn’:
drivers/s390/scsi/zfcp_aux.c:1379: warning: cast from pointer to integer of
different size
drivers/s390/scsi/zfcp_aux.c: In function ‘zfcp_fsf_incoming_els_plogi’:
drivers/s390/scsi/zfcp_aux.c:1432: warning: cast from pointer to integer of
different size
drivers/s390/scsi/zfcp_aux.c: In function ‘zfcp_fsf_incoming_els_logo’:
drivers/s390/scsi/zfcp_aux.c:1457: warning: cast from pointer to integer of
different size
..
Just passing pointers rids us of these warnings and improves readability.
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This patch removes the now obsolete erp_dbf trace.
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This patch allows any recovery event to be traced back to an exact
cause, e.g. a particular request identified by an id (address).
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This patch writes a trace record which provides information about state
changes for adapters, ports and units, e.g. target failure, targets becoming
online, targets being temporarily blocked due to pending recovery, targets
which have been recovered successfully etc.
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (200 commits)
[SCSI] usbstorage: use last_sector_bug flag universally
[SCSI] libsas: abstract STP task status into a function
[SCSI] ultrastor: clean up inline asm warnings
[SCSI] aic7xxx: fix firmware build
[SCSI] aacraid: fib context lock for management ioctls
[SCSI] ch: remove forward declarations
[SCSI] ch: fix device minor number management bug
[SCSI] ch: handle class_device_create failure properly
[SCSI] NCR5380: fix section mismatch
[SCSI] sg: fix /proc/scsi/sg/devices when no SCSI devices
[SCSI] IB/iSER: add logical unit reset support
[SCSI] don't use __GFP_DMA for sense buffers if not required
[SCSI] use dynamically allocated sense buffer
[SCSI] scsi.h: add macro for enclosure bit of inquiry data
[SCSI] sd: add fix for devices with last sector access problems
[SCSI] fix pcmcia compile problem
[SCSI] aacraid: add Voodoo Lite class of cards.
[SCSI] aacraid: add new driver features flags
[SCSI] qla2xxx: Update version number to 8.02.00-k7.
[SCSI] qla2xxx: Issue correct MBC_INITIALIZE_FIRMWARE command.
...
|
|
CC: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The common I/O layer can call remove a handler to inform zfcp
that a device disappeared. The handler zfcp_ccw_remove then
removes all unit, port and the adapter data structures. Removing
the units requires that the SCSI devices are removed first.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (207 commits)
[SCSI] gdth: fix CONFIG_ISA build failure
[SCSI] esp_scsi: remove __dev{init,exit}
[SCSI] gdth: !use_sg cleanup and use of scsi accessors
[SCSI] gdth: Move members from SCp to gdth_cmndinfo, stage 2
[SCSI] gdth: Setup proper per-command private data
[SCSI] gdth: Remove gdth_ctr_tab[]
[SCSI] gdth: switch to modern scsi host registration
[SCSI] gdth: gdth_interrupt() gdth_get_status() & gdth_wait() fixes
[SCSI] gdth: clean up host private data
[SCSI] gdth: Remove virt hosts
[SCSI] gdth: Reorder scsi_host_template intitializers
[SCSI] gdth: kill gdth_{read,write}[bwl] wrappers
[SCSI] gdth: Remove 2.4.x support, in-kernel changelog
[SCSI] gdth: split out pci probing
[SCSI] gdth: split out eisa probing
[SCSI] gdth: split out isa probing
gdth: Make one abuse of scsi_cmnd less obvious
[SCSI] NCR5380: Use scsi_eh API for REQUEST_SENSE invocation
[SCSI] usb storage: use scsi_eh API in REQUEST_SENSE execution
[SCSI] scsi_error: Refactoring scsi_error to facilitate in synchronous REQUEST_SENSE
...
|
|
Already register the debug feature before the zfcp adapter is
set online. This allows to use the debug feature to investigate
the online/offline sequence.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Introduce a shutdown method for the ccw bus that calls the driver
specific shutdown method in struct ccw_driver.
Switch zfcp to the new ccw_driver shutdown method.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
