summaryrefslogtreecommitdiffstats
path: root/drivers/scsi/libata-eh.c
AgeCommit message (Collapse)Author
2006-07-05[PATCH] libata: reimplement controller-wide PMTejun Heo
Reimplement controller-wide PM. ata_host_set_suspend/resume() are defined to suspend and resume a host_set. While suspended, EHs for all ports in the host_set are pegged using ATA_FLAG_SUSPENDED and frozen. Because SCSI device hotplug is done asynchronously against the rest of libata EH and the same mutex is used when adding new device, suspend cannot wait for hotplug to complete. So, if SCSI device hotplug is in progress, suspend fails with -EBUSY. In most cases, host_set resume is followed by device resume. As each resume operation requires a reset, a single host_set-wide resume operation may result in multiple resets. To avoid this, resume waits upto 1 second giving PM to request resume for devices. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-07-05[PATCH] libata: implement PM EH actionsTejun Heo
Implement two PM per-dev EH actions - ATA_EH_SUSPEND and ATA_EH_RESUME. Each action puts the target device into suspended mode and resumes from it respectively. Once a device is put to suspended mode, no EH operations other than RESUME is allowed on the device. The device will stay suspended till it gets resumed and thus reset and revalidated. To implement this, a new device state helper - ata_dev_ready() - is implemented and used in EH action implementations to make them operate only on attached & running devices. If all possible devices on a port are suspended, reset is skipped too. This prevents spurious events including hotplug events from disrupting suspended devices. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-07-05[PATCH] libata: implement ATA_EHI_NO_AUTOPSY and QUIETTejun Heo
Implement ATA_EHI_NO_AUTOPSY and QUIET. These used to be implied by ATA_PFLAG_LOADING, but new power management and PMP support need to use these separately. e.g. Suspend/resume operations shouldn't print full EH messages and resume shouldn't be recorded as an error. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-07-05[PATCH] libata: replace ap_lock w/ ap->lock in ata_scsi_error()Tejun Heo
ap_lock was used because &ap->host_set->lock was too long and used a lot. Now that &ap->host_set->lock is replaced with ap->lock, there's no reason to keep ap_lock. [ed. note: that's not entirely true. ap_lock is a local variable, caching the results of a de-ref. In theory, if the compiler is smart enough, this patch is cosmetic. However, since this is not a fast path (it is the error path), this patch is nonetheless acceptable, even though it _may_ introduce a performance regression.] Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-07-05[PATCH] libata: fix ehc->i.action setting in ata_eh_autopsy()Tejun Heo
ata_eh_autopsy() used to directly assign determined action mask to ehc->i.action thus overriding actions set by some of nested analyze functions. This patch makes ata_eh_autopsy() add action masks just as it's done in other places. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-07-05[PATCH] libata: add ap->pflags and move core dynamic flags to itTejun Heo
ap->flags is way too clamped. Separate out core dynamic flags to ap->pflags. ATA_FLAG_DISABLED is a dynamic flag but left alone as it's referenced by a lot of LLDs and it's gonna be removed once all LLDs are converted to new EH. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-06-26[PATCH] libata: clear EH action on device detachTejun Heo
Clear related EH action on device detach such that new device doesn't receive EH actions scheduled for the old one. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-06-26[PATCH] libata: implement and use ata_deh_dev_action()Tejun Heo
Implement and use ata_eh_dev_action() which returns EH action mask for a device. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-06-26[PATCH] libata: move ata_eh_clear_action() upwardTejun Heo
Move ata_eh_clear_action() upward. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-06-22[libata] Add host lock to struct ata_portJeff Garzik
Prepare for changes required to support SATA devices attached to SAS HBAs. For these devices we don't want to use host_set at all, since libata will not be the owner of struct scsi_host. Signed-off-by: Brian King <brking@us.ibm.com> (with slight merge modifications made by...) Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-06-22[PATCH] libata: implement per-dev EH action mask eh_info->dev_action[]Tejun Heo
Currently, the only per-dev EH action is REVALIDATE. EH used to exploit ehi->dev to do selective revalidation on a ATA bus. However, this is a bit hacky and makes it impossible to request selective revalidation from outside of EH or add another per-dev EH action. This patch adds per-dev EH action mask eh_info->dev_action[] and update EH to use this field for REVALIDATE. Note that per-dev actions can still be specified at port-level and it has the same effect of specifying the action for all devices on the port. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-06-12[PATCH] libata: fast exit from EH while unloadingTejun Heo
Make EH exit fast if the port is being unloaded. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-06-12[PATCH] libata: fix ATA_EH_REVALIDATE clearingTejun Heo
ATA_EH_REVALIDATE should be cleared after all devices on the target port have been revalidated. Fix ata_eh_revalidate_and_attach() accordingly. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-06-12[PATCH] Snoop SET FEATURES - WRITE CACHE ENABLE/DISABLE command(v5)zhao, forrest
This patch makes libata snoop 'SET FEATURES - WRITE CACHE ENABLE/DISABLE' command, executing requisite revalidation processes to update cached data. Signed-off-by: Forrest Zhao <forrest.zhao@intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-06-11[PATCH] libata: add missing finish_wait() call in ata_port_wait_eh()Tejun Heo
Add missing finish_wait() call after wait loop in ata_port_wait_eh(). Signed-off-by: Tejun Heo <htejun@gmail.com>
2006-05-31[PATCH] libata-hp: move ata_do_reset() to libata-eh.cTejun Heo
With ops->probe_init() gone, no user is left in libata-core.c. Move ata_do_reset() to libata-eh.c and make it static. Signed-off-by: Tejun Heo <htejun@gmail.com>
2006-05-31[PATCH] libata-hp: update unload-unplugTejun Heo
Update unload unplug - driver unloading / PCI removal. This is done by ata_port_detach() which short-circuits EH, disables all devices and freezes the port. With this patch, EH and unloading/unplugging are properly synchronized. Signed-off-by: Tejun Heo <htejun@gmail.com>
2006-05-31[PATCH] libata-hp: implement bootplugTejun Heo
Implement bootplug - boot probing via hotplug path. While loading, ata_host_add() simply schedules probing and invokes EH. After EH completes, ata_host_add() scans and assicates them with SCSI devices. EH path is slightly modified to handle this (e.g. no autopsy during bootplug). The SCSI part is left in ata_host_add() because it's shared with legacy path and to keep probing order as before (ATA scan all ports in host_set then attach all). Signed-off-by: Tejun Heo <htejun@gmail.com>
2006-05-31[PATCH] libata-hp: implement SCSI part of hotplugTejun Heo
Implement SCSI part of hotplug. This must be done in a separate context as SCSI makes use of EH during probing. SCSI scan fails silently if EH is in progress. In such cases, libata pauses briefly and retries until every device is attached. Signed-off-by: Tejun Heo <htejun@gmail.com>
2006-05-31[PATCH] libata-hp: implement hotplugTejun Heo
Implement ATA part of hotplug. To avoid probing broken devices over and over again, disabled devices are not automatically detached. They are detached only if probing is requested for the device or the associated port is offline. Also, to avoid infinite probing loop, Each device is probed only once per EH run. As SATA PHY status is fragile, devices are detached only after it has used up its recovery chances unless explicitly requested by LLDD or user (LLDD may request direct detach if, for example, it supports cold presence detection). Signed-off-by: Tejun Heo <htejun@gmail.com>
2006-05-31[PATCH] libata-hp: implement ata_eh_detach_dev()Tejun Heo
Implement ata_eh_detach_dev(). This function is responsible for detaching an ATA device and offlining the associated SCSI device atomically so that the detached device is not accessed after ATA detach is complete. Signed-off-by: Tejun Heo <htejun@gmail.com>
2006-05-31[PATCH] libata-hp-prep: implement followup softreset handlingTejun Heo
In some cases, hardreset must be followed by SRST. * some controllers can't classify with hardreset * some controllers can't wait for !BSY after hardreset (LLDD should explicitly request followup softreset by returning -EAGAIN) * (later) PM needs SRST w/ PMP==15 to operate after hardreset To handle above cases, this patch implements follow-up softreset. After a hardreset, ata_eh_reset() checks whether any of above conditions are met and do a follow-up softreset if necessary. Signed-off-by: Tejun Heo <htejun@gmail.com>
2006-05-31[PATCH] libata-hp-prep: add prereset() method and implement ata_std_prereset()Tejun Heo
With hotplug, every reset might be a probing reset and thus something similar to probe_init() is needed. prereset() method is called before a series of resets to a port and is the counterpart of postreset(). prereset() can tell EH to use different type of reset or skip reset by modifying ehc->i.action. This patch also implements ata_std_prereset(). Most controllers should be able to use this function directly or with some wrapping. After hotplug, different controllers need different actions to resume the PHY and detect the newly attached device. Controllers can be categorized as follows. * Controllers which can wait for the first D2H FIS after hotplug. Note that if the waiting is implemented by polling TF status, there needs to be a way to set BSY on PHY status change. It can be implemented by hardware or with the help of the driver. * Controllers which can wait for the first D2H FIS after sending COMRESET. These controllers need to issue COMRESET to wait for the first FIS. Note that the received D2H FIS could be the first D2H FIS after POR (power-on-reset) or D2H FIS in response to the COMRESET. Some controllers use COMRESET as TF status synchronization point and clear TF automatically (sata_sil). * Controllers which cannot wait for the first D2H FIS reliably. Blindly issuing SRST to spinning-up device often results in command issue failure or timeout, causing extended delay. For these controllers, ata_std_prereset() explicitly waits ATA_SPINUP_WAIT (currently 8s) to give newly attached device time to spin up, then issues reset. Note that failing to getting ready in ATA_SPINUP_WAIT is not critical. libata will retry. So, the timeout needs to be long enough to spin up most devices. LLDDs can tell ata_std_prereset() which of above action is needed with ATA_FLAG_HRST_TO_RESUME and ATA_FLAG_SKIP_D2H_BSY flags. These flags are PHY-specific property and will be moved to ata_link later. While at it, this patch unifies function typedef's such that they all have named arguments. Signed-off-by: Tejun Heo <htejun@gmail.com>
2006-05-31[PATCH] libata: implement ata_eh_wait()Tejun Heo
Implement ata_eh_wait(). On return from this function, it's guaranteed that the EH which was pending or in progress when the function was called is complete - including the tailing part of SCSI EH. This will be used by hotplug and others to synchronize with EH. Signed-off-by: Tejun Heo <htejun@gmail.com>
2006-05-31[PATCH] libata: set PIO-0 after successful EH resetTejun Heo
Set ata_device->pio_mode to XFER_PIO_0 after a successful reset. This is to keep EH resets consistent with probe resets as updated by the commit b6079ca409bf88c248992e96510dd6f610f7ed89. Note that, with soon-to-follow hotplug update, EH resets will include probe resets. Signed-off-by: Tejun Heo <htejun@gmail.com>
2006-05-20[PATCH] SCSI: make scsi_implement_eh() generic API for SCSI transportsTejun Heo
libata implemented a feature to schedule EH without an associated EH by manipulating shost->host_eh_scheduled in ata_scsi_schedule_eh() directly. Move this function to scsi_error.c and rename it to scsi_schedule_eh(). It is now an exported API for SCSI transports and exported via new header file drivers/scsi/scsi_transport_api.h This patch also de-export scsi_eh_wakeup() which was exported specifically for ata_scsi_schedule_eh(). Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-05-20[PATCH] libata: enforce default EH actionsTejun Heo
LLDDs rely on libata that certain EH actions are automatically taken on some errors. If the port is frozen or one or more qc's have failed with HSM violation or timeout, softreset is enforced (LLDD can ask for storonger EH action at will). If any other error condition exists, libata EH always revalidates. This behavior existed in earlier revisions of new EH but lost during development process. This patch restores it. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-05-15[PATCH] libata-ncq: update EH to handle NCQTejun Heo
Update EH to handle NCQ. ata_eh_autopsy() is updated to call ata_eh_analyze_ncq_error() which reads log page 10h on NCQ device error and updates eh_context accordingly. ata_eh_report() is updated to report SActive. Signed-off-by: Tejun Heo <htejun@gmail.com>
2006-05-15Merge branch 'irq-pio'Tejun Heo
Conflicts: drivers/scsi/libata-core.c include/linux/libata.h
2006-05-15[PATCH] libata-eh: implement new EHTejun Heo
Implement new EH. The exported interface is ata_do_eh() which is to be called from ->error_handler and performs the following steps to recover the failed port. ata_eh_autopsy() : analyze SError/TF, determine the cause of failure and required recovery actions and record it in ap->eh_context ata_eh_report() : report the failure to user ata_eh_recover() : perform recovery actions described in ap->eh_context ata_eh_finish() : finish failed qcs LLDDs can customize error handling by modifying eh_context before calling ata_do_eh() or, if necessary, doing so inbetween each major steps by calling each step explicitly. Signed-off-by: Tejun Heo <htejun@gmail.com>
2006-05-15[PATCH] libata-eh: implement ata_eh_info and ata_eh_contextTejun Heo
struct ata_eh_info serves as the communication channel between execution path and EH. Execution path describes detected error condition in ap->eh_info and EH recovers the port using it. To avoid missing error conditions detected during EH, EH makes its own copy of eh_info and clears it on entry allowing error info to accumulate during EH. Most EH states including EH's copy of eh_info are stored in ap->eh_context (struct ata_eh_context) which is owned by EH and thus doesn't require any synchronization to access and alter. This standardized context makes it easy to integrate various parts of EH and extend EH to handle multiple links (for PM). Signed-off-by: Tejun Heo <htejun@gmail.com>
2006-05-15[PATCH] libata-eh: implement dev->eringTejun Heo
This patch implements ata_ering and uses it to define dev->ering. ata_ering is a ring buffer which records libata errors - whether a command was for normar IO request, err_mask and timestamp. Errors are recorded per-device in dev->ering. This will be used by EH to determine recovery actions. Signed-off-by: Tejun Heo <htejun@gmail.com>
2006-05-15[PATCH] libata-eh-fw: update ata_scsi_error() for new EHTejun Heo
Update ata_scsi_error() for new EH. ata_scsi_error() is responsible for claiming timed out qcs and invoking ->error_handler in safe and synchronized manner. As the state of the controller is unknown if a qc has timed out, the port is frozen in such cases. Note that ata_scsi_timed_out() isn't used for new EH. This is because a timed out qc cannot be claimed by EH without freezing the port and freezing the port in ata_scsi_timed_out() results in unnecessary abortion of other active qcs. ata_scsi_timed_out() can be removed once all drivers are converted to new EH. While at it, add 'TODO: kill' comments to old EH functions. Signed-off-by: Tejun Heo <htejun@gmail.com>
2006-05-15[PATCH] libata-eh-fw: implement freeze/thawTejun Heo
Freezing is performed atomic w.r.t. host_set->lock and once frozen LLDD is not allowed to access the port or any qc on it. Also, libata makes sure that no new qc gets issued to a frozen port. A frozen port is thawed after a reset operation completes successfully, so reset methods must do its job while the port is frozen. During initialization all ports get frozen before requesting IRQ, so reset methods are always invoked on a frozen port. Optional ->freeze and ->thaw operations notify LLDD that the port is being frozen and thawed, respectively. LLDD can disable/enable hardware interrupt in these callbacks if the controller's IRQ mask can be changed dynamically. If the controller doesn't allow such operation, LLDD can check for frozen state in the interrupt handler and ack/clear interrupts unconditionally while frozen. Signed-off-by: Tejun Heo <htejun@gmail.com>
2006-05-15[PATCH] libata-eh-fw: implement ata_port_schedule_eh() and ata_port_abort()Tejun Heo
ata_port_schedule_eh() directly schedules EH for @ap without associated qc. Once EH scheduled, no further qc is allowed and EH kicks in as soon as all currently active qc's are drained. ata_port_abort() schedules all currently active commands for EH by qc_completing them with ATA_QCFLAG_FAILED set. If ata_port_abort() doesn't find any qc to abort, it directly schedule EH using ata_port_schedule_eh(). These two functions provide ways to invoke EH for conditions which aren't directly related to any specfic qc. Signed-off-by: Tejun Heo <htejun@gmail.com>
2006-05-15[PATCH] libata-eh-fw: implement new EH scheduling via error completionTejun Heo
There are several ways a qc can get schedule for EH in new EH. This patch implements one of them - completing a qc with ATA_QCFLAG_FAILED set or with non-zero qc->err_mask. ALL such qc's are examined by EH. New EH schedules a qc for EH from completion iff ->error_handler is implemented, qc is marked as failed or qc->err_mask is non-zero and the command is not an internal command (internal cmd is handled via ->post_internal_cmd). The EH scheduling itself is performed by asking SCSI midlayer to schedule EH for the specified scmd. For drivers implementing old-EH, nothing changes. As this change makes ata_qc_complete() rather large, it's not inlined anymore and __ata_qc_complete() is exported to other parts of libata for later use. Signed-off-by: Tejun Heo <htejun@gmail.com>
2006-05-15[PATCH] libata: use ATA printk helpersTejun Heo
Use ATA printk helpers. Signed-off-by: Tejun Heo <htejun@gmail.com>
2006-04-12Merge branch 'upstream'Jeff Garzik
2006-04-11libata: Add helper ata_shost_to_port()Jeff Garzik
2006-04-11libata: Fix EH merge difference between this branch and upstream.Jeff Garzik
2006-04-04[PATCH] libata-dev: irq-pio minor fixAlbert Lee
irq-pio minor fix: - remove the redundant hsm_task_state = HSM_ST_IDLE - add devno to printk() as done in upstream Signed-off-by: Albert Lee <albertcc@tw.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-04-02[libata] irq-pio: Fix merge mistakeJeff Garzik
2006-04-02[PATCH] libata: separate out libata-eh.cTejun Heo
A lot of EH codes are about to be added to libata. Separate out libata-eh.c. ata_scsi_timed_out(), ata_scsi_error(), ata_qc_timeout(), ata_eng_timeout(), ata_eh_qc_complete() and ata_eh_qc_retry() are moved. No code is changed by this patch. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>