| Age | Commit message (Collapse) | Author |
|---|
|
In LUN RESET testing involving NetApp targets, it is observed that LUN
RESET is failing. The fc_fcp_resp() is not completing the completion
for the LUN RESET task since fc_fcp_resp assumes that the FCP_RSP_INFO
is 8 bytes with the 4 byte reserved field, where in case of NetApp targets
the FCP_RSP to LUN RESET only has 4 bytes of FCP_RSP_INFO. This leads
fc_fcp_resp to error out w/o completing the task completion, eventually
causing LUN RESET to be escalated to host reset, which is not very nice.
Per FCP-3 r04, clause 9.5.15 and Table 23, the FCP_RSP_INFO field can be either
4 bytes or 8 bytes, with the last 4 bytes as "Reserved (if any)". Therefore it
is valid to have 4 bytes FCP_RSP_INFO like some of the NetApp targets behave.
Fixing this by validating the FCP_RSP_INFO against both the two spec allowed
length.
Reported-by: Frank Zhang <frank_1.zhang@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This is exposed in the case the FCP_DATA frames somehow got lost and fc_fcp got
the FCP_RSP, in fc_fcp_recv_resp(), since xfer_len is less than the expected_len
it resets the the timer to wait to 2 more jiffies in case the data frames are
already queued locally. However, for target does not support REC, it would just
send RJT w/ ELS_RJT_UNSUP. The rec response handler thus only clears the rport
flag for not doing REC later, but does not do fcp_io_complete() on the
associated fsp.
The fix is just check status of FCP_RSP being received already, i.e. using the
FC_SRB_RCV_STATUS flag, in fc_fcp_timeout before start sending REC. We should
have waited long enough if there is truely data frames queued locally.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The FC-GS-3 sepc requires to wait for least 3 times R_A_TOV per
sec 4.6.1 "If the Requesting_CT does not receive a Response
CT_IU from the Responding_CT within three times R_A_TOV,
it shall consider this to be a protocol error."
This means added four new states with management server
could add significant delay with multiple retries
on default 12 second timeout(3 * R_A_TOV), so instead
just skip these states on very first timeout on any of
these states to not stuck with states for such longer
period.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The lport_recv(), i.e., fc_lport_recv_req() may get called w/o the sequence ptr
being set in fr_seq(), particularly in the case of vn2vn mode, this may happen
if the passive fcp provider, e.g., tcm_fc, has not been registered yet.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Add exch timeout info to have debug log with exch timeout
value to match with retries, also add debug info
on exch timer cancel.
Added common fc_exch_timer_cancel() func and grouped this
along with fc_exch_timer_set() function, so that
added debug code is not repeated.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Updates newly added stats from fc_get_host_stats,
added new function fc_exch_update_stats to
update exches related stats from fc_exch.c
by going thru internal ema_list elements.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Acked-by : Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Adds stats to track FCP pkt and frame alloc
failure.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Acked-by : Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The libfc is used by fcoe but fcoe agnostic,
and therefore should not have any fcoe references.
So renaming fcoe_dev_stats from libfc as its for fc_stats.
After that libfc is fcoe string free except some strings for
Open-FCoE.org.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Acked-by : Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Acked-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
isci update for 3.5
1/ Rework remote-node-context (RNC) handling for proper management of
the silicon state machine in error handling and hot-plug conditions.
Further details below, suffice to say if the RNC is mismanaged the
silicon state machines may lock up.
2/ Refactor the initialization code to be reused for suspend/resume support
3/ Miscellaneous bug fixes to address discovery issues and hardware
compatibility.
RNC rework details from Jeff Skirvin:
In the controller, devices as they appear on a SAS domain (or
direct-attached SATA devices) are represented by memory structures known
as "Remote Node Contexts" (RNCs). These structures are transferred from
main memory to the controller using a set of register commands; these
commands include setting up the context ("posting"), removing the
context ("invalidating"), and commands to control the scheduling of
commands and connections to that remote device ("suspensions" and
"resumptions"). There is a similar path to control RNC scheduling from
the protocol engine, which interprets the results of command and data
transmission and reception.
In general, the controller chooses among non-suspended RNCs to find one
that has work requiring scheduling the transmission of command and data
frames to a target. Likewise, when a target tries to return data back
to the initiator, the state of the RNC is used by the controller to
determine how to treat the incoming request. As an example, if the RNC
is in the state "TX/RX Suspended", incoming SSP connection requests from
the target will be rejected by the controller hardware. When an RNC is
"TX Suspended", it will not be selected by the controller hardware to
start outgoing command or data operations (with certain priority-based
exceptions).
As mentioned above, there are two sources for management of the RNC
states: commands from driver software, and the result of transmission
and reception conditions of commands and data signaled by the controller
hardware. As an example of the latter, if an outgoing SSP command ends
with a OPEN_REJECT(BAD_DESTINATION) status, the RNC state will
transition to the "TX Suspended" state, and this is signaled by the
controller hardware in the status to the completion of the pending
command as well as signaled in a controller hardware event. Examples of
the former are included in the patch changelogs.
Driver software is required to suspend the RNC in a "TX/RX Suspended"
condition before any outstanding commands can be terminated. Failure to
guarantee this can lead to a complete hardware hang condition. Earlier
versions of the driver software did not guarantee that an RNC was
correctly managed before I/O termination, and so operated in an unsafe
way.
Further, the driver performed unnecessary contortions to preserve the
remote device command state and so was more complicated than it needed
to be. A simplifying driver assumption is that once an I/O has entered
the error handler path without having completed in the target, the
requirement on the driver is that all use of the sas_task must end.
Beyond that, recovery of operation is dependent on libsas and other
components to reset, rediscover and reconfigure the device before normal
operation can restart. In the driver, this simplifying assumption meant
that the RNC management could be reduced to entry into the suspended
state, terminating the targeted I/O request, and resuming the RNC as
needed for device-specific management such as an SSP Abort Task or LUN
Reset Management request.
|
|
The lport could get timeout armed while its getting disabled,
so flush lport worker after its disabled and ignore lport
retry in that case instead of WARN_ON.
[13192.936858] WARNING: at drivers/scsi/libfc/fc_lport.c:1573 fc_lport_timeout+0x53/0xa9 [libfc]()
[13192.938026] Hardware name: Bochs
[13192.938620] Modules linked in: fcoe libfcoe libfc scsi_transport_fc scsi_tgt fuse 8021q garp stp llc sunrpc ipv6 uinput microcode joydev pcspkr ixgbe e1000 i2c_piix4 i2c_core virtio_balloon dca mdio virtio_blk virtio_pci virtio_ring virtio floppy [last unloaded: speedstep_lib]
[13192.942589] Pid: 23605, comm: kworker/0:6 Tainted: G W 3.2.0+ #71
[13192.943587] Call Trace:
[13192.944052] [<ffffffff810403f4>] warn_slowpath_common+0x85/0x9d
[13192.944940] [<ffffffff81040426>] warn_slowpath_null+0x1a/0x1c
[13192.945734] [<ffffffffa02746eb>] fc_lport_timeout+0x53/0xa9 [libfc]
[13192.946665] [<ffffffff81058d88>] process_one_work+0x20c/0x3ad
[13192.947541] [<ffffffff81058cbe>] ? process_one_work+0x142/0x3ad
[13192.948423] [<ffffffffa0274698>] ? fc_lport_enter_ns+0x178/0x178 [libfc]
[13192.949363] [<ffffffff8105a313>] worker_thread+0xfd/0x181
[13192.950191] [<ffffffff8105a216>] ? manage_workers.clone.15+0x173/0x173
[13192.951100] [<ffffffff8105e19b>] kthread+0xa4/0xac
[13192.951755] [<ffffffff814edbb4>] kernel_thread_helper+0x4/0x10
[13192.952520] [<ffffffff814e5cb4>] ? retint_restore_args+0x13/0x13
[13192.953398] [<ffffffff8105e0f7>] ? __init_kthread_worker+0x5b/0x5b
[13192.954278] [<ffffffff814edbb0>] ? gs_change+0x13/0x13
[13192.954911] ---[ end trace 9763213b95bbd803 ]---
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
A previous commit changed the mfs checking to ensure the new
mfs is less or equal to the mfs supported by the FCF. This
doesn't work for BRDCM cards as they set an mfs of 2048 regardless
of whether the switch returns a larger mfs.
This patch validates the new mfs against the upper and lower spec
defined boundries for a FCoE mfs.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
Pull SCSI updates from James Bottomley:
"This is primarily another round of driver updates (lpfc, bfa, fcoe,
ipr) plus a new ufshcd driver. There shouldn't be anything
controversial in here (The final deletion of scsi proc_ops which
caused some build breakage has been held over until the next merge
window to give us more time to stabilise it).
I'm afraid, with me moving continents at exactly the wrong time,
anything submitted after the merge window opened has been held over to
the next merge window."
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (63 commits)
[SCSI] ipr: Driver version 2.5.3
[SCSI] ipr: Increase alignment boundary of command blocks
[SCSI] ipr: Increase max concurrent oustanding commands
[SCSI] ipr: Remove unnecessary memory barriers
[SCSI] ipr: Remove unnecessary interrupt clearing on new adapters
[SCSI] ipr: Fix target id allocation re-use problem
[SCSI] atp870u, mpt2sas, qla4xxx use pci_dev->revision
[SCSI] fcoe: Drop the rtnl_mutex before calling fcoe_ctlr_link_up
[SCSI] bfa: Update the driver version to 3.0.23.0
[SCSI] bfa: BSG and User interface fixes.
[SCSI] bfa: Fix to avoid vport delete hang on request queue full scenario.
[SCSI] bfa: Move service parameter programming logic into firmware.
[SCSI] bfa: Revised Fabric Assigned Address(FAA) feature implementation.
[SCSI] bfa: Flash controller IOC pll init fixes.
[SCSI] bfa: Serialize the IOC hw semaphore unlock logic.
[SCSI] bfa: Modify ISR to process pending completions
[SCSI] bfa: Add fc host issue lip support
[SCSI] mpt2sas: remove extraneous sas_log_info messages
[SCSI] libfc: fcoe_transport_create fails in single-CPU environment
[SCSI] fcoe: reduce contention for fcoe_rx_list lock [v2]
...
|
|
Starting fcoe fails at fcoe_transport_create when attempting to allocate a
pool of 4K exchanges on a 64-bit single-CPU environment because the call to
__alloc_percpu() is greater than the max of 32K. This patch reduces the
number of exchanges to fit within the maximum allowed space.
[ Whitespace problems fixed by Robert Love to satisfy chechpatch.pl ]
Signed-off-by: Steven Clark <sclark@crossbeam.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Currently fc_host mfs is not getting updated in
case its changed during FLOGI and that leaves fc_host
to show its initial old value in sysfs, so instead
have fc_host mfs updated along with updating lport mfs
during FLOGI.
Also in case of bad mfs during flogi, error out
instead of continuing with flogi.
[ Changes made by Robert Love: condition to '>=' and
added printing of lport->mfs in DBG statement. FLOGI
resp processing failed without being able to compare
FCoE MFS 2112 against an incoming MFS of 2112 ]
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
SCSI updates from James Bottomley:
"The update includes the usual assortment of driver updates (lpfc,
qla2xxx, qla4xxx, bfa, bnx2fc, bnx2i, isci, fcoe, hpsa) plus a huge
amount of infrastructure work in the SAS library and transport class
as well as an iSCSI update. There's also a new SCSI based virtio
driver."
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (177 commits)
[SCSI] qla4xxx: Update driver version to 5.02.00-k15
[SCSI] qla4xxx: trivial cleanup
[SCSI] qla4xxx: Fix sparse warning
[SCSI] qla4xxx: Add support for multiple session per host.
[SCSI] qla4xxx: Export CHAP index as sysfs attribute
[SCSI] scsi_transport: Export CHAP index as sysfs attribute
[SCSI] qla4xxx: Add support to display CHAP list and delete CHAP entry
[SCSI] iscsi_transport: Add support to display CHAP list and delete CHAP entry
[SCSI] pm8001: fix endian issue with code optimization.
[SCSI] pm8001: Fix possible racing condition.
[SCSI] pm8001: Fix bogus interrupt state flag issue.
[SCSI] ipr: update PCI ID definitions for new adapters
[SCSI] qla2xxx: handle default case in qla2x00_request_firmware()
[SCSI] isci: improvements in driver unloading routine
[SCSI] isci: improve phy event warnings
[SCSI] isci: debug, provide state-enum-to-string conversions
[SCSI] scsi_transport_sas: 'enable' phys on reset
[SCSI] libsas: don't recover end devices attached to disabled phys
[SCSI] libsas: fixup target_port_protocols for expanders that don't report sata
[SCSI] libsas: set attached device type and target protocols for local phys
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
Pull SCSI target updates from Nicholas Bellinger:
"This contains the usual set of updates and bugfixes to target-core +
existing fabric module code, along with a handful of the patches
destined for v3.3 stable.
It also contains the necessary target-core infrastructure pieces
required to run using tcm_qla2xxx.ko WWPNs with the new Qlogic Fibre
Channel fabric module currently queued in target-pending/for-next-merge,
and coming for round 2.
The highlights for this series include:
- Add target_submit_tmr() helper function for fabric task management
(andy)
- Convert tcm_fc to use target_submit_tmr() (andy)
- Replace target core various cmd flags with a transport state (hch)
- Convert loopback to use workqueue submission (hch)
- Convert target core to use array_zalloc for tpg_lun_list (joern)
- Convert target core to use array_zalloc for device_list (joern)
- Add target core support for TMR_ABORT_TASK (nab)
- Add target core se_sess->sess_kref + get/put helpers (nab)
- Add target core se_node_acl->acl_kref for ->acl_free_comp usage
(nab)
- Convert iscsi-target to use target_put_session + sess_kref (nab)
- Fix tcm_fc fc_exch memory leak in ft_send_resp_status (nab)
- Fix ib_srpt srpt_handle_cmd send_ioctx->ioctx_kref leak on
exception (nab)
- Fix target core up handling of short INQUIRY buffers (roland)
- Untangle target-core front-end and back-end meanings of max_sectors
attribute (roland)
- Set loopback residual field for SCSI commands (roland)
- Fix target-core 16-bit target ports for SET TARGET PORT GROUPS
emulation (roland)
Thanks again to Andy, Christoph, Joern, Roland, and everyone who has
contributed this round!"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (64 commits)
ib_srpt: Fix srpt_handle_cmd send_ioctx->ioctx_kref leak on exception
loopback: Fix transport_generic_allocate_tasks error handling
iscsi-target: remove improper externs
iscsi-target: Remove unused variables in iscsi_target_parameters.c
target: remove obvious warnings
target: Use array_zalloc for device_list
target: Use array_zalloc for tpg_lun_list
target: Fix sense code for unsupported SERVICE ACTION IN
target: Remove hack to make READ CAPACITY(10) lie if thin provisioning is enabled
target: Bump core version to v4.1.0-rc2-ml + fabric versions
tcm_fc: Fix fc_exch memory leak in ft_send_resp_status
target: Drop unused legacy target_core_fabric_ops API callers
iscsi-target: Convert to use target_put_session + sess_kref
target: Convert se_node_acl->acl_group removal to use ->acl_kref
target: Add se_node_acl->acl_kref for ->acl_free_comp usage
target: Add se_node_acl->acl_free_comp for NodeACL release path
target: Add se_sess->sess_kref + get/put helpers
target: Convert session_lock to irqsave
target: Fix typo in drivers/target
iscsi-target: Fix dynamic -> explict NodeACL pointer reference
...
|
|
Signed-off-by: Cong Wang <amwang@redhat.com>
|
|
This allows us to use scsilun_to_int without an ugly cast.
Fix up places that use scsilun_to_int on fcp->fc_lun accordingly.
In fc target, this leaves ft_cmd.lun unused, so remove it.
Signed-off-by: Andy Grover <agrover@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Kiran Patil <kiran.patil@intel.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
While we wait for GPN_FT response, if the ctlr link goes down, the stack
generates a completion for GPN_FT with error FC_EXCH_CLOSED, and reports a
discovery error. Discovery is not retried in this case, and rightly so.
However, the 'pending' flag stays set, which does not allow subsequent
discovery to succeed as GPN_FT will never be issued. Fix it by clearing the
pending flag when the discovery fails due to GPN_FT failure.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Adding and removing the host into the zone causes this panic.
BUG: unable to handle kernel NULL pointer dereference at 00000000000000a0
IP: [<ffffffffa0491707>] fc_exch_recv+0xc57/0xe70 [libfc]
Call Trace:
[<ffffffffa050e04b>] bnx2fc_l2_rcv_thread+0x37b/0x430 [bnx2fc]
[<ffffffffa050dcd0>] ? bnx2fc_l2_rcv_thread+0x0/0x430 [bnx2fc]
[<ffffffff81090886>] kthread+0x96/0xa0
[<ffffffff8100c14a>] child_rip+0xa/0x20
[<ffffffff810907f0>] ? kthread+0x0/0xa0
[<ffffffff8100c140>] ? child_rip+0x0/0x20
During fc_exch_reset, the active exchanges are aborted and the exch is deleted.
As part of processing ABTS response, due to 'ep' being NULL, any access to ep in
fc_exch_recv_bls() causes this panic. Fixed to access 'ep' only if non-NULL.
Reviewed-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This patch adds support for Fabric Device Management
Interface as per FC-GS-4 spec. in libfc. Any driver
making use of libfc can enable fdmi state machine
for a given lport.
If lport has enabled FDMI support the lport state
machine will transition into FDMI after completing
the DNS states and before entering the SCR state.
The FDMI state transition is such that if there is an
error, it won't stop the lport state machine from
transitioning and the it will behave as if there was
no FDMI support.
The FDMI HBA attributes are registed with the Management
server via Register HBA (RHBA) command and the port
attributes are reigstered using the Register Port(RPA)
command.
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Acked-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Currently the libfc Common Transport(CT) calls assume that
the CT requests are Name Server specific only. This patch
makes it more flexible to allow more FC-GS services to make
use of these routines.
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Acked-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The fcp timer is already initialized when it gets allocated.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Avoid that sparse complains about missing declarations for local
functions by declaring these static or by adding an #include directive.
Add the __percpu annotation where it is missing.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
|
|
The module.h header was implicitly present everywhere, so files
with no explicit include of the module infrastructure would build
anyway. We are now removing the implicit include, and so we need
to call out the module.h file that we need explicitly.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
For the basic SCSI infrastructure files that are exporting symbols
but not modules themselves, add in the basic export.h header file
to allow the exports.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Adds more cases to do flogi retry, now also retry
on getting bad response due to either no ELS response
or flogi response payload length not large enough.
In those cases flogi was not retried and that
was leaving lport offline.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Currently timer delay is large and is using msleep to avoid
avoid exchanges collision across lport reset, so instead
do this by initializing exches pool indexes during
reset also.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Its checked after skb freed, so instead have fh_type
cached and then check FC_TYPE_BLS against cached
fh_type value.
This wrong check was causing double exch locking as
reported by Bhanu at
https://lists.open-fcoe.org/pipermail/devel/2011-October/011793.html
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (204 commits)
[SCSI] qla4xxx: export address/port of connection (fix udev disk names)
[SCSI] ipr: Fix BUG on adapter dump timeout
[SCSI] megaraid_sas: Fix instance access in megasas_reset_timer
[SCSI] hpsa: change confusing message to be more clear
[SCSI] iscsi class: fix vlan configuration
[SCSI] qla4xxx: fix data alignment and use nl helpers
[SCSI] iscsi class: fix link local mispelling
[SCSI] iscsi class: Replace iscsi_get_next_target_id with IDA
[SCSI] aacraid: use lower snprintf() limit
[SCSI] lpfc 8.3.27: Change driver version to 8.3.27
[SCSI] lpfc 8.3.27: T10 additions for SLI4
[SCSI] lpfc 8.3.27: Fix queue allocation failure recovery
[SCSI] lpfc 8.3.27: Change algorithm for getting physical port name
[SCSI] lpfc 8.3.27: Changed worst case mailbox timeout
[SCSI] lpfc 8.3.27: Miscellanous logic and interface fixes
[SCSI] megaraid_sas: Changelog and version update
[SCSI] megaraid_sas: Add driver workaround for PERC5/1068 kdump kernel panic
[SCSI] megaraid_sas: Add multiple MSI-X vector/multiple reply queue support
[SCSI] megaraid_sas: Add support for MegaRAID 9360/9380 12GB/s controllers
[SCSI] megaraid_sas: Clear FUSION_IN_RESET before enabling interrupts
...
|
|
fix holes and better cache aligned fields.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Re-arrange its fields to avoid padding and have better
cacheline alignments.
Removed not used start_time, end_time and last_pkt_time
fields.
This all reduced this struct size to 448 from 480 and
that also reduced one cacheline on x86_64 beside
eliminating 8 pads. However kept logical fields together.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
In commit 6a716a8, while releasing the DDP context in case frame_send() failed,
the frame may already be freed, so we should store the pointer to fc_fcp_pkt and
release the DDP context using the locally stored fsp instead of getting fsp from
the fr_fsp(fp) on a frame.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Reported-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Call fc_block_scsi_eh() in all fcoe eh to blocks
the scsi_eh thread for blocked rports.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Reviewed-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Current fc_eh_host_reset leaves lport offline
permanently due to FLOGI response getting
handled by LOGO response from last reset as both
had same exchange id.
So fix this by having end to end exches clean-up
using exchange abort along exches reset
done from fc_eh_host_reset. This would avoid
exchanges collision between the sessions across
the reset. In this case implicit login should have
done that but no aborting support for FIP
frames, so just wait till lport->r_a_tov before
restarting next flogi to ensure all exchanges
are good to use again for next session.
Below is the trace of LOGO from older session
coming ahead of FLOGI response with same exche id
0x203:-
617 86.435165 4e.00.0b -> ff.ff.fc FC ELS LOGO 0x203
618 86.435195 4e.00.0b -> b6.02.00 FC ELS LOGO 0x213
619 86.435220 4e.00.0b -> 18.03.00 FC ELS LOGO 0x223
620 86.435244 4e.00.0b -> 18.02.00 FC ELS LOGO 0x233
621 86.435267 4e.00.0b -> 18.01.00 FC ELS LOGO 0x243
622 86.435349 00.00.00 -> ff.ff.fe FC ELS FLOGI 0x203
623 86.435549 ff.ff.fc -> 4e.00.0b FC ELS ACC (LOGO) 0x203
624 86.438721 ff.ff.fe -> 4e.00.0b FC ELS ACC (FLOGI) 0x203
625 86.442059 18.03.00 -> 4e.00.0b FC ELS ACC (LOGO) 0x223
626 86.443683 b6.02.00 -> 4e.00.0b FC ELS ACC (LOGO) 0x213
627 86.447693 18.01.00 -> 4e.00.0b FC ELS ACC (LOGO) 0x243
628 86.453499 18.02.00 -> 4e.00.0b FC ELS ACC (LOGO) 0x233
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Reviewed-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The lport retry timer hits warn on in case
it has become ready in response from fip
login from fcoe_ctlr_flogi_send(), this is
possible but safe code path, therefore
removing this warn on.
Jun 22 03:16:30 10.0.16.6 [488198.316517] host3: Assigned Port ID 180f02
Jun 22 03:16:32 10.0.16.6 [488200.091561] ------------[ cut here ]------------
Jun 22 03:16:32 10.0.16.6 [488200.091586] WARNING: at
drivers/scsi/libfc/fc_lport.c:1355 fc_lport_timeout+0xd9/0xe0 [libfc]()
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
fc_queuecommand() allocates an FCP packet for each SCSI command and sends
it out on the wire. In the process it stores the reference to the FCP packet
in the scsi_cmnd structure.
Now, in case under stress testing the libfc exchange layer runs out of
exchanges the fc_queuecommand() may not be able to send out commands out on
the wire. In such a scenario if there is an error in sending the FCP packet
out the wire; fc_queuecommand() deletes the FCP packet from internal queue,
releases the FCP packet and returns a SCSI_MLQUEUE_HOST_BUSY status to the
scsi-ml. But, the reference to the FCP packet set in the scsi_cmnd is not
removed from the scsi_cmnd in this code path.
This might lead to a crash under stress testing where the scsi_cmnd failed by
fc_queuecommand() comes up to fc_eh_abort() via scsi eh thread. fc_eh_abort()
will get reference to the FCP packet to be aborted from the scsi_cmnd for
further FCP abort related processing and then try to release the FCP packet
that has already been released.
This patch removes the FCP packet reference from the scsi_cmnd before returning
back from fc_queuecommand() in case of an error in sending out the FCP packet.
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The variable on stack, namely cdb_op, is not used but removed.
[ Patch reworked by Robert Love due to invalid patch format ]
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
One change is to cleanup typo in comment for fc_fcp_recv(), another corrects
the misleading comment for fc_fcp_abts_resp().
[ Patch reworked by Robert Love due to invalid patch format ]
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Drop the rx frame having xid with wrong cpu info
or received with xid not matching to our xid.
Not dropping such frame is causing panic as
that causes accessing data struct beyond their
bounds.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
If fail to create workqueue, the newly created cache for exchg has to be
released.
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Reviewed-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Though defined, FC_MAX_ERROR_CNT is not used. It is used now for CRC error in
the path of receiving FCP frame.
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (77 commits)
[SCSI] fix crash in scsi_dispatch_cmd()
[SCSI] sr: check_events() ignore GET_EVENT when TUR says otherwise
[SCSI] bnx2i: Fixed kernel panic due to illegal usage of sc->request->cpu
[SCSI] bfa: Update the driver version to 3.0.2.1
[SCSI] bfa: Driver and BSG enhancements.
[SCSI] bfa: Added support to query PHY.
[SCSI] bfa: Added HBA diagnostics support.
[SCSI] bfa: Added support for flash configuration
[SCSI] bfa: Added support to obtain SFP info.
[SCSI] bfa: Added support for CEE info and stats query.
[SCSI] bfa: Extend BSG interface.
[SCSI] bfa: FCS bug fixes.
[SCSI] bfa: DMA memory allocation enhancement.
[SCSI] bfa: Brocade-1860 Fabric Adapter vHBA support.
[SCSI] bfa: Brocade-1860 Fabric Adapter PLL init fixes.
[SCSI] bfa: Added Fabric Assigned Address(FAA) support
[SCSI] bfa: IOC bug fixes.
[SCSI] bfa: Enable ASIC block configuration and query.
[SCSI] bnx2i: Updated copyright and bump version
[SCSI] bnx2i: Modified to skip CNIC registration if iSCSI is not supported
...
Fix up some trivial conflicts in:
- drivers/scsi/bnx2fc/{bnx2fc.h,bnx2fc_fcoe.c}:
Crazy broadcom version number conflicts
- drivers/target/tcm_fc/tfc_cmd.c
Just trivial cleanups done on adjacent lines
|
|
The rcu callback fc_rport_free_rcu() just calls a kfree(),
so we use kfree_rcu() instead of the call_rcu(fc_rport_free_rcu).
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Robert Love <robert.w.love@intel.com>
Cc: "James E.J. Bottomley" <James.Bottomley@suse.de>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
|
|
Post an FCH_EVT_LIPRESET event on lport reset as
as lport reset occurs on FIP cleat virtual link,
this could be due to change in fcoe vlan and this
event will allow user app fcoemon to switch to
new fcoe vlan.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
target and connected to windows initaitor
Problem: Linux based SW target (TCM) connected to windows initiator
was unable to satisfy write request of size > 2K.
Fix: Existing linux implememtation of FCoE stack is expecting sequence
number to match w.r.t incoming framme. When DDP is used on target in
response to write request from initiator, SW stack is notified only
when last data frame arrives and only the pakcket header of last data
frame is posted to NetRx queue of storage. When that last packet was
processed in libfc:Exchange layer, implementation was expecting
sequence number to match, but in this case sequence number which is
embedded in FC Header is assigned by windows initaitor, hence due to
sequence number mismatch post-processing which shall result into
sending RSP is not done. Enhanced the code to utilize the sequence
number of incoming last frame and process the packet so that, it will
eventually complete the write request by sending write response (RSP)
GOOD.
Notes/Dependencies: This patch is validated using windows and linux
initiator to make sure, it doesn't break anything.
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Problem: Existing RPORT state machine continues witg FLOGI/PLOGI
process only after it receices beacon from other end. Once claiming
stage is over (either clain notify or clain repose), beacon is sent
and state machine enters into operational mode where it initiates the
rlogin process (FLOGI/PLOGI) to the peer but before this rlogin is
initiated, exitsing implementation checks if it received beacon from
other end, it beacon is not received yet, rlogin process is not
initiated. Other end initiates FLOGI but peer end keeps on rejecting
FLOGI, hence after 3 retries other end deletes associated rport, then
sends a beacon. Once the beacon is received, peer end now initiates
rlogin to the peer end but since associated rport is deleted FLOGI is
neither accepted nor the reject response send out because rport is
deleted. Hence unable to proceed withg FLOGI/PLOGI process and fails
to establish VN2VN connection.
Fix: VN2VN spec is not standard yet but based on exitsing collateral
on T11, it appears that, both end shall send beacon and enter into
'operational mode' without explictly waiting for beacon from other
end. Fix is to allow the RPORT login process as long as respective
RPORT is created (as part of claim notification / claim response) even
though state of RPORT is INIT. Means don't wait for beacon from peer
end, if peer end initiates FLOGI (means peer end exist and
responding).
Notes: This patch is preparing the FCoE stack for target wrt
offload. This is generic patch and harmless even if applied on storage
initiator because 'else if' condition of function 'fcoe_oem_found'
shall evaluate to TRUE only for targets.
Dependencies: None
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
fc_fcp_send_data
Currently, when seq_send() fails in fc_fcp_send_data(),
fc_fcp_retry_cmd() would complete this failed I/O directly and let
scsi-ml retry. However, target side is not notified which may hang the
target. Instead, we should just bail out from from fc_fcp_send_data
and let scsi-ml times it out and aborts this I/O instead.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
|
In this case fsp was freed before error handler was invoked,
this is fixed by having SRR fsp reference freed by exch
destructor so that fsp will be always held until it exch
is freed.
Also don't reset fsp->recov_seq since this is needed by
SRR error handler to do exch done.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
