| Age | Commit message (Collapse) | Author |
|---|
|
- Added driver support for management application to pass down two security
specific mailbox commands (MBX_SECURITY_MGMT and MBX_AUTH_PORT)
- Added driver support for handling FIPS zeroization trap of host ERATT ER8,
performing selective reset and bringing the device up.
- Added code to detect INIT_LINK mailbox command completion returning status
MBXERR_SEC_NO_PERMISSION.
- Increased the wait timeout on host status register HS_FFRDY and HS_MBRDY
being set.
- Remove the port offline code from the Heartbeat TMO handler.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
- Move Unload flag earlier in vport deletei to stop ELS traffic
- Replaced some unnecessary spin_lock_irqsave with spin_lock_irq
- Fixed circular spinlock dependency between low-level driver and SCSI midlayer
- Remove duplicate code from lpfc_els_retry routine
- Make all error values negative
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
This removes the driver's get_host_def_dev_loss_tmo
callback and just has the driver set the dev loss
using the fc class fc_host_dev_loss_tmo macro like is
done for other fc params.
It also adds compat support for the driver's existing
dev loss and nodev sysfs and modparams.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
- Add support for re-reg'ing changed VPI w/o unregister VPI
- Copy WWN and state from old nodelist when target DID change.
- Clean up old nodelist rport and put the nodelist when target DID change.
- Clear the VFI_REGISTERED flag when UNREG_VFI completes.
- Made both checks of port_state against LPFC_FLOGI and LPFC_FDISC
non-inclusive for ignoring CVL events.
- Added logic to stop retrying of the ongoing PLOGI and FDISC if
transitioned back to the FCF rediscovery state in reaction to CVL.
- Removed the dependency of scanning of all the available FCF table
entries for bulding round-robin bitmap.
- Use the lpfc_sli4_fcf_rr_read_fcf_rec() in responding to
individual New FCF found event.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
- Remove unneeded Endian swap for Block Guard IOCB response
- Add a check for mailbox active before issuing the heartbeat command
- Correct heartbeat last_completion updates to avoid unneeded heartbeats
- Add Security crypto support to CONFIG_PORT mailbox command
- Add fips level and fips spec revision sysfs parameters
- Remove duplicate setting of ext_byte_len fields in lpfc_bsg_issue_mbox
- Switch call to memcpy_toio to __write32_copy to prevent unaligned 64 bit copy
- Change log message 0318 from an error to a warning as it is not an error
- Patch an incorrect call to lpfc_drain_txq on SLI-3 functions
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
FCoE Related Fixes
- Correct find-next-FCF routine so that it searches at next FCF rather
than current one.
- Enhanced round-robin FCF failover algorithm to re-start on "New FCF"
async event
- Update the manner in which we look at FCFs while they may be in
their discovery state.
- Use LPFC_FCOE_NULL_VID macro when checkinf for valid vlan_id for FCF
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
- Fixed accounting of allocated SCSI buffers when post sgl fails.
- Restrict scsi buffer allocation based on LUN count (sdev_cnt).
- Create __lpfc_sli_free_rpi that doesn't take out the hbalock.
- Modify lpfc_sli_free_rpi to call __lpfc_sli_free_rpi.
- Call __lpfc_sli_free_rpi in lpfc_cleanup_pending_mbox.
- Do not swap the strings returned in mailbox commands and do
not swap byte aligned data in VPD.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
- Allow enabling MSI-X intterupts with fewer vectors than requested
by looking at the return value from pci_enable_msix.
- Implemented driver PCI AER error handling routines for supporting
AER error recovering on SLI4 devices.
- Remove redundant SLI_ACTIVE checks
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
- Change the Max receive size on CIN FCFs to 0x800
- (From linux community) Check boundary before checking for NULL.
- Update last completion time for completed I/O to prevent heartbeat.
- Add Balius PCI Device IDs
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
- Fix hba_queue_depth to reflect actual available XRIs
- Add support for new SLER specific firmware status codes.
- Free SCSI buffer when iotag allocation fails.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
- Add poll or wait flag parameter to hba_init_link and hba_down_link.
- (From Linux Community) Make return with ENXIO negative.
- Remove unused INB code from driver.
- Prevent block_magmt_io from returning until mailbox is inactive.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
- Add code to prevent unreg_vpi mailbox command from failing.
- Add code to reset the HBA if unreg_vpi mailbox fails with busy status.
- Remove code that was clearing the nlp_type stored during rport discovery.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
- Move the code to increase the sg seg count for LP21000 adapters.
- Check pcmd on command completion before dereferencing it.
- Clear queue memory when creating firmware queues to prevent stale entries.
- Replace the use of PAGE_SIZE in many areas that assumed it was always 4k.
- Add an else clause to a conditional that needed to unlock the hba_lock.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
- Add the new Logical Link speed event support.
- Add RATOV and EDTOV to the REG_VFI mailbox command.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Only abort outstanding I/O to force the OS to retry failed I/Os for AER
uncorrectable non-fatal errors instead of reseting the adapter.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
- Add BSG support for PCI loopback testing.
- Add BSG support for extended mailbox commands.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
- Correct all SLI4 code to work on big endian systems.
- Move read of sli4 params earlier so returned values are used correctly.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
FCF failover improvements
- Add random FCF failover when there are multiple FCFs available.
- Prevent FCF log messages from being displayed for FC adapters.
- Separate the New FCF and Modified FCF log messages.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
|
|
- Added round robin FCF failover on initial or FCF rediscovery FLOGI failure.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
- Prevent Vport discovery after reg_new_vport completes when physical
logged in using FDISC.
- Remove fast FCF failover fabric name matching. Allow failover to FCFs
connected to different fabrics.
- Added fast FCF failover in response to FCF DEAD event on current
FCF record.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
- Clear LPFC_DRIVER_ABORTED on FCP command completion.
- Clear exchange busy flag when I/O is aborted and found on aborted list.
- Free sglq when XRI_ABORTED event is processed before release of IOCB.
- Only process iocb as aborted when LPFC_DRIVER_ABORTED is set.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
- Add Logging message for critial errors.
- Remove unused variable from lpfc_nodev_tmo_show
- Update supress_link_up parameter with #define values.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
- Add NULL checks to the pointers for the config_async mailbox
and dump_wakeup_params mailbox.
- Add code to check return value of lpfc_read_sparams everywhere
and handle failures appropriately.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
- Use the hbalock when changing the fc_flag.
- Use the host_lock when changeing the sli_flag.
- Prevent NULL pointer dereference after dma_alloc_coherent failure.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
- Convert all sysfs parameters to uint instead of int.
- Add lpfc_supress_link_up parameter.
- Change link_state to writable sysfs parameter.
- Add support to be able to "up" or "down" link from link_state parameter.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
- Add support for the INTF (Interface) PCI register.
- Add support for greater than 2 page SGLs.
- Add support for up to 32 bit BDE lengths.
- Implement the Port Capabilities Mailbox command.
- Stop checking the Minor Code in the EQE structure.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
- Add init_vpi mailbox command before re-registering VPI.
- Add Fast FCF failover support.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
- Call pci_save_state() after pci_restore_state() call to cope
with kernel change.
- Add support for PCI BAR region 0 if BAR0 is a 64 bit register.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Update BSG infrastructure to handle new vendor specific BSG commands.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Display Logical Link Speed when supported and is non-zero.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Discovery relates changes:
- Separated VPI_REGISTERED state of physical port into VFI_REGISTERED and
VPI_REGISTERED state so that driver can unregister physical port VPI
independent of VFI.
- Add code to unregister, re-init and re-register physical port VPI
when physical port NportID change.
- Add code to unregister and re-register VPI of a vport when its Nport
ID change.
- Add code in FDISC completion path to re-start FLOGI discovery when
a FDISC complete with LOGIN_REQUIRED reason code.
- Fix a memory leak in lpfc_init_vpi_cmpl
- Add code to start a timer for vport to retry FDISC when CVL is received
by a vport or physical port. If all Nports receive CVLs, then all timers
are cancelled and a logical link level discovery will be started after
one second.
- Flush ELS commands after killing all delayed ELS commands.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Fix discovery failures:
- Move all accesses to the fc_flag field inside the host lock.
- Restore link state after going through linkdown processing for FCF DEAD event.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Fix SCSI protocol related errors:
- Avoid I/O failures during EEH and HBA/CNA reset by correcting when
we block the targets on the adapter.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Fix hardware/SLI relates issues:
- Fix CNA uses more than one EQ when in INTx interrupt mode.
- Fix driver tries to process failed read FCF record mailbox request.
- Fix allocating single receive buffer breaks FCoE receive queue.
- Support new read FCF record mailbox error case.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
In testing 2.6.31 on one of our ia64 platforms I've encountered a hang
due to the driver using hardware ATEs which are a limited resource.
This is because the driver does not set the dma consistent mask to
64 bits.
Signed-off-by: Michael Reed <mdr@sgi.com>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (42 commits)
tree-wide: fix misspelling of "definition" in comments
reiserfs: fix misspelling of "journaled"
doc: Fix a typo in slub.txt.
inotify: remove superfluous return code check
hdlc: spelling fix in find_pvc() comment
doc: fix regulator docs cut-and-pasteism
mtd: Fix comment in Kconfig
doc: Fix IRQ chip docs
tree-wide: fix assorted typos all over the place
drivers/ata/libata-sff.c: comment spelling fixes
fix typos/grammos in Documentation/edac.txt
sysctl: add missing comments
fs/debugfs/inode.c: fix comment typos
sgivwfb: Make use of ARRAY_SIZE.
sky2: fix sky2_link_down copy/paste comment error
tree-wide: fix typos "couter" -> "counter"
tree-wide: fix typos "offest" -> "offset"
fix kerneldoc for set_irq_msi()
spidev: fix double "of of" in comment
comment typo fix: sybsystem -> subsystem
...
|
|
Hardware related Fixes and Changes.
- Added new Adapter IDs and update default Adapter names.
- Added PCI read after EQarm doorbell PCI write to flush the write
and avoid spurrious interrupts when in INTx mode.
- Phase out use of ONLINE registers.
- Fix for lost MSI interrupt
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Fix errors relating to crashes and hangs.
- Fix crash due to list corruption while unloading driver.
- Fix panic during pci-hot-plug testing.
- Fix panic when unmapping luns.
- Fixed total_scsi_bufs counting could cause exhausted memory.
- Fixed locking issue causing hang.
- Fixed the call from lpfc_new_scsi_buf_s3 to use lpfc_release_scsi_buf_s3.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Fix AER issues.
- Made AER sysfs entry point return "Operation not permitted" to
OneConnect HBAs
- Stop and abort all I/Os on HBA for AER uncorrectable non-fatal error
handling
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
FC protocol fixes.
- Fix send sequence logic to handle multi SGL IOCBs.
- Fix FDISC completion always setting VPORT state to failed.
- Ported the fix on reporting of max_vpi to uppper layer.
- Fix incorrect number of Vports allowed to be created.
- Fixed Dead FCoE port after creating vports.
- Added handling of ELS request for Reinstate Recovery Qualifier (RRQ)
- Handle unsolicited CT exchange initiator receiving CT exchange ABTS
- Migrate LUN queue depth ramp up code to scsi mid-layer.
- Made ABTS WQE go to the same WQ as the WQE to be aborted.
- Fix Vport does not rediscover after FCF goes away.
- Fixed lpfc_unreg_vfi failure after devloss timeout.
- Fixed RPI bit leak.
- Fix hbq pointer corruption during target discovery.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
FCoE Protocol fixes.
- Fixed FIP frame designation for ELS commands.
- Fix CVL received on Port 1 not processed by driver.
- Fix Zeroed frame on wire after FLOGI
- Fix vport keep-alive does not contain the correct WWN.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
optimisations and devloss timout fixes
This patch includes the following changes:
- Fixed Panic/Hang when using polling mode for fcp commands
- Added support for Read_rev mbox bits indicating FIP mode of HBA
- Optimize performance of slow-path handling of els responses
- Add code to cleanup orphaned unsolicited receive sequences
- Fixed Devloss timeout when multiple initiators are in same zone
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
update logging
This patch include the following fixes and changes:
- Fix crash when "error" is echoed to board_mode sysfs parameter
- Fix FCoE Parameter parsing in regions 23
- Fix driver crash when creating vport with large number of targets on SLI4
- Fix bug with npiv message being logged when it is not supported by the adapter
- Fix a potential dereferencing mailbox structure after free bug
- Fix firmware crash after vport create with high target count
- Error out requests to set board_mode to warm restart via sysfs on SLI4 HBAs
- Fix Block guard logging
- Fix a memory corruption issue during GID_FT IO prep
- Fix crash while processing unsolicited FC frames
- Fix failed to allocate XRI message is not a critical failure
- Update and fix formatting in some log messages
- Fix missing new line characters in log messages
- Removed the use of the locally defined FC transport layer related macros
- Check the rsplen in lpfc_handle_fcp_err function before using rsplen
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
vlink events
This patch includes the following fixes and new features:
- Fix mask size for CT field in WQE
- Fix VPI base not used when unregistering VPI on port 1.
- Fix UNREG_VPI mailbox command to unreg the correct VPI
- Fixed Check for aborted els command
- Fix error when trying to load driver with wrong firmware on FCoE HBA.
- Fix bug with probe_one routines not putting the Scsi_Host back upon error
- Add support for Clear Virtual Link Async Events
- Add support for unsolicited CT exchange sequence abort
- Add 0x0714 OCeXXXXX PCI ID
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
This patch includes the following fixes:
- Fixed panic during HBA reset.
- Fixed FCoE event tag passed in resume_rpi.
- Fix out of order ELS commands
- Fixed discovery issues found during VLAN testing.
- Fix UNREG_VPI failure on extended link pull
- Fixed crash while processing unsolicited FC frames.
- Clear retry count in the delayed ELS handler
- Fixed discovery failure during quick link bounce.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Some of our virtual SCSI hosts don't have a proper bus parent at the
top, which can be a problem for doing DMA on them
This patch makes the host device cache a pointer to the physical bus
device and provides an extra API for setting it (the normal API picks
it up from the parent). This patch also modifies the qla2xxx and lpfc
vport logic to use the new DMA host setting API.
Acked-By: James Smart <james.smart@emulex.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
