| Age | Commit message (Collapse) | Author |
|---|
|
Right now the Makefile for the mpt3sas driver does not even allow the
driver to be built into the kernel. So fix that up, as there doesn't
seem to be any obvious reason why this shouldn't be done.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Jan Vesely <jvesely@redhat.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Added a driver module parameter max_msix_vectors. Using this module parameter
the maximum number of MSI-X vectors could be set.
The number of MSI-X vectors used would be the minimum of MSI-X vectors
supported by the HBA, the number of CPU cores and the value set to
max_msix_vectors module parameter.
The default value of this module parameter is set to 8. The default value of
this parameter is set to 8 inorder to reduce the amount of memory required for
Reply Descriptor Post queue. This is because with the higher MSI-X vectors,
some times kernel is not able to allocate the requested amount of memory and
crash is observed. To overcome this problem, the default value is set to 8.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
If mpt3sas_base_map_resources takes an early error path then its
counterpart, mpt3sas_base_free_resources needs to be careful about
cleaning up:
1 - _base_mask_interrupts and _base_make_ioc_ready require memory
mapped I/O registers, make sure that this is true.
2 - _base_free_irq iterates over the adapter's reply_queue_list, so
move this list head initialization out of _base_enable_msix to
_scsih_probe so this will always be safe.
3 - check that the controller PCI device and its BARs have been
enabled before disabling them.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Bump driver version to v02.100.00.00.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
are removed but their transport layer entries are not removed
When Async scanning mode is enabled and device scanning is in progress,
devices should not be removed. But in actuality, devices are removed but
their transport layer entries are not removed. This causes error to add
the same device to the transport layer after host reset or diagnostic
reset.
So, in this patch, modified the code in such a way that device is not removed
when Async scanning mode is enabled and device scanning is in progress.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Change set in MPI v2.5 Rev F(v2.5.1.1) specification and 2.00.29 header files
1. Added a bit to the IOCExceptions field of the IOCFacts Reply to indicate
that the IOC detected a partial memory failure.
2. Added ElapsedSeconds field to RAID Volume Indicator Structure. Added
Elapsed Seconds Valid flag to Flags field of this structure.
3. Added ElapsedSeconds field to Integrated RAID Operations Status Event Data.
4. Added two new AbortType values for TargetModeAbort Request, one to abort
all I/Os from a single initiator, and the other to abort only Command IUs.
5. Added a new chapter covering DMA Flags and Multicast Modes.
6. In the IOCSettings field of BIOS Page 1, modified the Adapter Support bits
description to specify X86 BIOS.
7. Marked bit 0 of the ControlFlags field of SAS IO Unit Page 1 as
obsolete. This was the Clear SATA Affiliation flag.
8. Added additional requirements for certain IOCs that support more than eight
MSI-x vectors.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
MPI2_IOCSTATUS_CONFIG_INVALID_PAGE is not returned
Infinite loop can occur if IOCStatus is not equal to
MPI2_IOCSTATUS_CONFIG_INVALID_PAGE value in the while loops in functions
_scsih_search_responding_sas_devices,
_scsih_search_responding_raid_devices and
_scsih_search_responding_expanders
So, Instead of checking for MPI2_IOCSTATUS_CONFIG_INVALID_PAGE value,
in this patch code is modified to check for IOCStatus not equals to
MPI2_IOCSTATUS_SUCCESS to break the while loop.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
non LUN 0 configured expander
With some enclosures when LUN 0 is not created but LUN 1 or LUN X is created
then SCSI scan procedure calls target_alloc, slave_alloc call back functions
for LUN 0 and slave_destory() for same LUN 0.
In these kind of cases within slave_destroy, pointer to scsi_target in
_sas_device structure is set to NULL, following which when slave_alloc for LUN
1 is called then starget would not be set properly for this LUN. So,
scsi_target pointer pointing to NULL value would lead to a crash later in the
discovery procedure.
To solve this issue set the sas_device's scsi_target pointer to scsi_device's
scsi_target if it is NULL earlier in slave_alloc callback function.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Hardware timing requirements is updated in order to comply with firmware
requirement.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The Copyright String in all mpt3sas files are changed to 2012-2013.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull VFS updates from Al Viro,
Misc cleanups all over the place, mainly wrt /proc interfaces (switch
create_proc_entry to proc_create(), get rid of the deprecated
create_proc_read_entry() in favor of using proc_create_data() and
seq_file etc).
7kloc removed.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (204 commits)
don't bother with deferred freeing of fdtables
proc: Move non-public stuff from linux/proc_fs.h to fs/proc/internal.h
proc: Make the PROC_I() and PDE() macros internal to procfs
proc: Supply a function to remove a proc entry by PDE
take cgroup_open() and cpuset_open() to fs/proc/base.c
ppc: Clean up scanlog
ppc: Clean up rtas_flash driver somewhat
hostap: proc: Use remove_proc_subtree()
drm: proc: Use remove_proc_subtree()
drm: proc: Use minor->index to label things, not PDE->name
drm: Constify drm_proc_list[]
zoran: Don't print proc_dir_entry data in debug
reiserfs: Don't access the proc_dir_entry in r_open(), r_start() r_show()
proc: Supply an accessor for getting the data from a PDE's parent
airo: Use remove_proc_subtree()
rtl8192u: Don't need to save device proc dir PDE
rtl8187se: Use a dir under /proc/net/r8180/
proc: Add proc_mkdir_data()
proc: Move some bits from linux/proc_fs.h to linux/{of.h,signal.h,tty.h}
proc: Move PDE_NET() to fs/proc/proc_net.c
...
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Correct spelling typo in various drivers.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The variable 'chain_flags' and 'phy_number' are initialized but never used
otherwise, So remove those unused variables.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
linux/version.h is not necessary as detected by checkversion.pl script.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: "Sreekanth Reddy" <Sreekanth.reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
ioc->diag_trigger_mpi is an SL_WH_MPI_TRIGGERS_T struct.
There is a cut and paste error here and SL_WH_EVENT_TRIGGERS_T is used
instead of SL_WH_MPI_TRIGGERS_T. Since the SL_WH_EVENT_TRIGGERS_T is
smaller than SL_WH_MPI_TRIGGERS_T, it means we only clear part of the
buffer.
I've changed it to use sizeof(ioc->diag_trigger_mpi) which is a bit
simpler.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: "Sreekanth Reddy" <Sreekanth.reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Adam Radford <linuxraid@lsi.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
These driver files are initially, substantially similar to mpt2sas but,
because mpt2sas is going into maintenance mode and mp3sas will become heavily
developed, we elected to keep the code bases separate.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Reviewed-by: Nagalakshmi Nandigama <Nagalakshmi.Nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
