| Age | Commit message (Collapse) | Author |
|---|
|
The libfc provides more flexibility and with that
we can monitor some more FC specific stats for
FC exches or FCP error cases, this patch add
such new FC stats.
The patch adds *only* FC specific new stats to
existing fc_host attribute container.
Added stats names are self explanatory as
existing FC stats already has, however anyway
still added commentary along their definition
to describe them.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Acked-by : Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Commit a7a20d103994 ("sd: limit the scope of the async probe domain")
make the SCSI device probing run device discovery in it's own async
domain.
However, as a result, the partition detection was no longer synchronized
by async_synchronize_full() (which, despite the name, only synchronizes
the global async space, not all of them). Which in turn meant that
"wait_for_device_probe()" would not wait for the SCSI partitions to be
parsed.
And "wait_for_device_probe()" was what the boot time init code relied on
for mounting the root filesystem.
Now, most people never noticed this, because not only is it
timing-dependent, but modern distributions all use initrd. So the root
filesystem isn't actually on a disk at all. And then before they
actually mount the final disk filesystem, they will have loaded the
scsi-wait-scan module, which not only does the expected
wait_for_device_probe(), but also does scsi_complete_async_scans().
[ Side note: scsi_complete_async_scans() had also been partially broken,
but that was fixed in commit 43a8d39d0137 ("fix async probe
regression"), so that same commit a7a20d103994 had actually broken
setups even if you used scsi-wait-scan explicitly ]
Solve this problem by just moving the scsi_complete_async_scans() call
into wait_for_device_probe(). Everybody who wants to wait for device
probing to finish really wants the SCSI probing to complete, so there's
no reason not to do this.
So now "wait_for_device_probe()" really does what the name implies, and
properly waits for device probing to finish. This also removes the now
unnecessary extra calls to scsi_complete_async_scans().
Reported-and-tested-by: Artem S. Tashkinov <t.artem@mailcity.com>
Cc: Dan Williams <dan.j.williams@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: James Bottomley <jbottomley@parallels.com>
Cc: Borislav Petkov <bp@amd64.org>
Cc: linux-scsi <linux-scsi@vger.kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The netdev->base_addr parameter has been deprecated in the L2 bnx2
driver. This is used by bnx2i for the BARn iomapping.
This patch will directly reference the pci_resource_start instead
of using the deprecated netdev->base_addr.
This patch is actually a critical bug fix as the 1G bnx2 driver no
longer supports the netdev->base_addr in the current kernel of the scsi
tree. This means that Broadcom's 1G Linux iSCSI offload solution would
not work at all without this patch.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
fill_result_tf() grabs the taskfile flags from the originating qc which
sas_ata_qc_fill_rtf() promptly overwrites. The presence of an
ata_taskfile in the sata_device makes it tempting to just copy the full
contents in sas_ata_qc_fill_rtf(). However, libata really only wants
the fis contents and expects the other portions of the taskfile to not
be touched by ->qc_fill_rtf. To that end store a fis buffer in the
sata_device and use ata_tf_from_fis() like every other ->qc_fill_rtf()
implementation.
Cc: <stable@vger.kernel.org>
Reported-by: Praveen Murali <pmurali@logicube.com>
Tested-by: Praveen Murali <pmurali@logicube.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Pull target fixes from Nicholas Bellinger:
"Two minor target fixes. There is really nothing exciting and/or
controversial this time around.
There's one fix from MDR for a RCU debug warning message within tcm_fc
code (CC'ed to stable), and a small AC fix for qla_target.c based upon
a recent Coverity static report.
Also, there is one other outstanding virtio-scsi LUN scanning bugfix
that has been uncovered with the in-flight tcm_vhost driver over the
last days, and that needs to make it into 3.5 final too. This patch
has been posted to linux-scsi again here:
http://marc.info/?l=linux-scsi&m=134160609212542&w=2
and I've asked James to include it in his next PULL request."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
qla2xxx: print the right array elements in qlt_async_event
tcm_fc: Resolve suspicious RCU usage warnings
|
|
Based upon Alan's patch from Coverity scan id 793583, these debug
messages in qlt_async_event() should be starting from byte 0, which is
always the Asynchronous Event Status Code from the parent switch statement.
Also, rename reason_code -> login_code following the language used in
2500 FW spec for Port Database Changed (0x8014) -> Port Database Changed
Event Mailbox Register for mailbox[2].
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Several bug reports have been received recently for USB mass-storage
devices that don't handle READ CAPACITY(16) commands properly. They
report bogus sizes, in some cases becoming unusable as a result.
The bugs were triggered by commit
09b6b51b0b6c1b9bb61815baf205e4d74c89ff04 (SCSI & usb-storage: add
flags for VPD pages and REPORT LUNS), which caused usb-storage to stop
overriding the SCSI level reported by devices. By default, the sd
driver will try READ CAPACITY(16) first for any device whose level is
above SCSI_SPC_2.
It seems likely that any device large enough to require the use of
READ CAPACITY(16) (i.e., 2 TB or more) would be able to handle READ
CAPACITY(10) commands properly. Indeed, I don't know of any devices
that don't handle READ CAPACITY(10) properly.
Therefore this patch (as1559) adds a new flag telling the sd driver
to try READ CAPACITY(10) before READ CAPACITY(16), and sets this flag
for every USB mass-storage device. If a device really is larger than
2 TB, sd will fall back to READ CAPACITY(16) just as it used to.
This fixes Bugzilla #43391.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Hans de Goede <hdegoede@redhat.com>
CC: "James E.J. Bottomley" <JBottomley@parallels.com>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a couple of minor fixes, one for a preempt warning in the
mpt2sas driver and one is a config failure with the new sd async
domain."
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] Fix sd_probe_domain config problem
[SCSI] mpt2sas: Fix unsafe using smp_processor_id() in preemptible
|
|
version.h header file is no longer required for qla_target code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
If we make a variable an unsigned int and then expect it to be < 0 on
a bad character, we're going to have a bad time. Fix the tcm_qla2xxx
code to actually notice if hex_to_bin() returns a negative variable.
This was detected by the compiler warning:
scsi/qla2xxx/tcm_qla2xxx.c: In function ‘tcm_qla2xxx_npiv_extract_wwn’:
scsi/qla2xxx/tcm_qla2xxx.c:148:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
If we go to the "out_term:" exit path in qlt_do_work(), we call
qlt_send_term_exchange() with a NULL cmd, which means that it can't
possibly free the cmd for us. Add an explicit call to free the
command memory, so we don't leak the allocation.
This will also fix warnings about "BUG qla_tgt_cmd_cachep: Objects
remaining on kmem_cache_close" from slub when unloading the qla2xxx
target module.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
In qlt_do_ctio_completion(), there's no point in calling
qlt_term_ctio_exchange() with a NULL cmd -- all that it does is crash
in a NULL pointer dereference, since it does
qlt_send_term_exchange(vha, cmd, &cmd->atio, 1);
and dereferencing &cmd->atio is a bad idea if cmd itself is NULL.
If we really need to do this, we could take the values from the
failed CTIO we're processing, but it's not clear if it's worth
the replumbing to do that.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
When we create an explicit node ACL in tcm_qla2xxx_make_nodeacl(),
there is a call to tcm_qla2xxx_setup_nacl_from_rport(), which puts the
node ACL into the lport_fcport_map even though there is no session yet
for the initiator. Since the only time we remove entries from this
map is when we free a session, this means that if we later delete this
node ACL without the initiator ever creating a session, we'll leave
the nacl pointer in the btree pointing at freed memory.
This is especially bad if that initiator later does send us a command
that would cause us to create a dynamic ACL and session: we'll find
the stale freed nacl pointer in the btree and end up with use-after-free.
We could add more code to clear the btree entry when deleting the
explicit nacl, but the original insertion is pointless: without a
session attached, we'll just have to update the entry when a session
appears anyway. So we can just delete tcm_qla2xxx_setup_nacl_from_rport()
and the code that calls it.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch adds a new tcm_qla2xxx_clear_sess_lookup() call to clear session
specific s_id + loop_id entries used for se_node_acl pointer lookup ahead
of releasing se_session within the process context workqueue callback in
tcm_qla2xxx_free_session().
It makes the call in existing tcm_qla2xxx_clear_nacl_from_fcport_map()
code invoked from qlt_unreg_sess() in interrupt context w/ hardware_lock
held, ahead of the process context callback into qlt_free_session_done()
-> tcm_qla2xxx_free_session().
We are doing this to address a race between incoming ATIO or TMR packets
using stale se_node_acl pointer once session shutdown has been invoked via
qlt_unreg_sess() in qla_target.c LLD code, and when the entire tcm_qla2xxx
endpoint has not been forced into shutdown w/ echo 0 > ../$QLA2XXX_PORT/enable
Cc: Joern Engel <joern@logfs.org>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch converts tcm_qla2xxx code to use an internal kref_put() for
se_session->sess_kref in order to ensure that qla_hw_data->hardware_lock
can be held while calling qlt_unreg_sess() for the final put.
Signed-off-by: Joern Engel <joern@logfs.org>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
With CONFIG_BLK_DEV_SD = n and CONFIG_PM = n, you get this compile failure:
(.text+0x4f6c77): undefined reference to `scsi_sd_probe_domain'
This was introduced by
commit a7a20d103994fd760766e6c9d494daa569cbfe06
Author: Dan Williams <dan.j.williams@intel.com>
Date: Thu Mar 22 17:05:11 2012 -0700
[SCSI] sd: limit the scope of the async probe domain
And happens because scsi_sd_probe_domain is conditionally defined but
unconditionally used. Fix this by making the symbol unconditionally defined.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Dan Williams <dan.j.williams@intel.com>
Tested-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
When CONFIG_DEBUG_PREEMPT is enabled, bug is observed in the smp_processor_id().
This is because smp_processor_id() is not called in preempt safe condition.
To fix this issue, use raw_smp_processor_id instead of smp_processor_id.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
CC: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Pull final round of SCSI updates from James Bottomley:
"This is primarily another round of driver updates (bnx2fc, qla2xxx,
qla4xxx) including the target mode driver for qla2xxx. We've also got
a couple of regression fixes (async scanning, broken this merge window
and a fix to a long standing break in the scsi_wait_scan module)."
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (45 commits)
[SCSI] fix scsi_wait_scan
[SCSI] fix async probe regression
[SCSI] be2iscsi: fix dma free size mismatch regression
[SCSI] qla4xxx: Update driver version to 5.02.00-k17
[SCSI] qla4xxx: Capture minidump for ISP82XX on firmware failure
[SCSI] qla4xxx: Add change_queue_depth API support
[SCSI] qla4xxx: Fix clear ddb mbx command failure issue.
[SCSI] qla4xxx: Fix kernel panic during discovery logout.
[SCSI] qla4xxx: Correct early completion of pending mbox.
[SCSI] fcoe, bnx2fc, libfcoe: SW FCoE and bnx2fc use FCoE Syfs
[SCSI] libfcoe: Add fcoe_sysfs
[SCSI] bnx2fc: Allocate fcoe_ctlr with bnx2fc_interface, not as a member
[SCSI] fcoe: Allocate fcoe_ctlr with fcoe_interface, not as a member
[SCSI] Fix dm-multipath starvation when scsi host is busy
[SCSI] ufs: fix potential NULL pointer dereferencing error in ufshcd_prove.
[SCSI] qla2xxx: don't free pool that wasn't allocated
[SCSI] mptfusion: unlock on error in mpt_config()
[SCSI] tcm_qla2xxx: Add >= 24xx series fabric module for target-core
[SCSI] qla2xxx: Add LLD target-mode infrastructure for >= 24xx series
[SCSI] Revert "qla2xxx: During loopdown perform Diagnostic loopback."
...
|
|
Commit c751085943362143f84346d274e0011419c84202
Author: Rafael J. Wysocki <rjw@sisk.pl>
Date: Sun Apr 12 20:06:56 2009 +0200
PM/Hibernate: Wait for SCSI devices scan to complete during resume
Broke the scsi_wait_scan module in 2.6.30. Apparently debian still uses it so
fix it and backport to stable before removing it in 3.6.
The breakage is caused because the function template in
include/scsi/scsi_scan.h is defined to be a nop unless SCSI is built in.
That means that in the modular case (which is every distro), the
scsi_wait_scan module does a simple async_synchronize_full() instead of
waiting for scans.
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Commit a7a20d1 "[SCSI] sd: limit the scope of the async probe domain"
moved sd probe work out of reach of wait_for_device_probe(). Allow it
to be synced via scsi_complete_async_scans().
Reported-by: Meelis Roos <mroos@linux.ee>
Tested-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This patch should go into 3.5 fixes. The bug was added in the
patches for the 3.5 feature window.
As you can see from the patch I made a mistake. During
development I switched from passing a struct to the size of
the struct, but left the sizeof. This results in us allocating
4 bytes (sizeof(int)) but then calling pci_free_consistent
with the size of the struct.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Added support to capture dump (Minidump) which allows us to
catpure a snapshot of the firmware/hardware states at the time
of firmware failure
Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: Shyam Sundar <shyam.sundar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
change_queue_depth will adjust device queuedepth upon receiving
"SAM_STAT_TASK_SET_FULL" scsi status from the target.
Also added ql4xqfulltracking command line param to enable or disable
queuefull tracking. One can disabling queuefull tracking to ensure
user set scsi device queuedepth is not altered.
Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Allow ddb state to change to DDB_DS_NO_CONNECTION_ACTIVE or
DDB_DS_SESSION_FAILED before issuing clear ddb mailbox cmd,
because clear ddb mailbox cmd fails if the ddb state is not
equal to DDB_DS_NO_CONNECTION_ACTIVE or DDB_DS_SESSION_FAILED.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Update the session and connection parameter before sending
connection logged in event to iscsiadm because in some
scenario logout may come in just after we send the logged
in event to user, which free up session, connection and ddb,
but DPC is still updating session and connect parameter
which can lead to panic.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Check for Firmware Hang (AF_FW_RECOVERY) after mailbox command
has gained access to ensure that the mailbox command does not
wait un-necessarily during a firmware recovery and prevent
premature mailbox timeout which will lead to back to back reset's.
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull the MCA deletion branch from Paul Gortmaker:
"It was good that we could support MCA machines back in the day, but
realistically, nobody is using them anymore. They were mostly limited
to 386-sx 16MHz CPU and some 486 class machines and never more than
64MB of RAM. Even the enthusiast hobbyist community seems to have
dried up close to ten years ago, based on what you can find searching
various websites dedicated to the relatively short lived hardware.
So lets remove the support relating to CONFIG_MCA. There is no point
carrying this forward, wasting cycles doing routine maintenance on it;
wasting allyesconfig build time on validating it, wasting I/O on git
grep'ping over it, and so on."
Let's see if anybody screams. It generally has compiled, and James
Bottomley pointed out that there was a MCA extension from NCR that
allowed for up to 4GB of memory and PPro-class machines. So in *theory*
there may be users out there.
But even James (technically listed as a maintainer) doesn't actually
have a system, and while Alan Cox claims to have a machine in his cellar
that he offered to anybody who wants to take it off his hands, he didn't
argue for keeping MCA support either.
So we could bring it back. But somebody had better speak up and talk
about how they have actually been using said MCA hardware with modern
kernels for us to do that. And David already took the patch to delete
all the networking driver code (commit a5e371f61ad3: "drivers/net:
delete all code/drivers depending on CONFIG_MCA").
* 'delete-mca' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
MCA: delete all remaining traces of microchannel bus support.
scsi: delete the MCA specific drivers and driver code
serial: delete the MCA specific 8250 support.
arm: remove ability to select CONFIG_MCA
|
|
This patch has the SW FCoE driver and the bnx2fc
driver make use of the new fcoe_sysfs API added
earlier in this patch series.
After this patch a fcoe_ctlr_device is allocated with
private data in this order.
+------------------+ +------------------+
| fcoe_ctlr_device | | fcoe_ctlr_device |
+------------------+ +------------------+
| fcoe_ctlr | | fcoe_ctlr |
+------------------+ +------------------+
| fcoe_interface | | bnx2fc_interface |
+------------------+ +------------------+
libfcoe also takes part in this new model since it
discovers and manages fcoe_fcf instances. The memory
allocation is different for FCFs. I didn't want to
impact libfcoe's fcoe_fcf processing, so this patch
creates fcoe_fcf_device instances for each discovered
fcoe_fcf. The two are paired using a (void * priv)
member of the fcoe_ctlr_device. This allows libfcoe
to continue maintaining its list of fcoe_fcf instances
and simply attaches and detaches them from existing
or new fcoe_fcf_device instances.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This patch adds a 'fcoe bus' infrastructure to the kernel
that is driven by changes to libfcoe which allow LLDs to
present FIP (FCoE Initialization Protocol) discovered
entities and their attributes to user space via sysfs.
This patch adds the following APIs-
fcoe_ctlr_device_add
fcoe_ctlr_device_delete
fcoe_fcf_device_add
fcoe_fcf_device_delete
They allow the LLD to expose the FCoE ENode Controller
and any discovered FCFs (Fibre Channel Forwarders, e.g.
FCoE switches) to the user. Each of these new devices
has their own bus_type so that they are grouped together
for easy lookup from a user space application. Each
new class has an attribute_group to expose attributes
for any created instances. The attributes are-
fcoe_ctlr_device
* fcf_dev_loss_tmo
* lesb_link_fail
* lesb_vlink_fail
* lesb_miss_fka
* lesb_symb_err
* lesb_err_block
* lesb_fcs_error
fcoe_fcf_device
* fabric_name
* switch_name
* priority
* selected
* fc_map
* vfid
* mac
* fka_peroid
* fabric_state
* dev_loss_tmo
A device loss infrastructre similar to the FC Transport's
is also added by this patch. It is nice to have so that a
link flapping adapter doesn't continually advance the count
used to identify the discovered FCF. FCFs will exist in a
"Disconnected" state until either the timer expires or the
FCF is rediscovered and becomes "Connected."
This patch generates a few checkpatch.pl WARNINGS that
I'm not sure what to do about. They're macros modeled
around the FC Transport attribute building macros, which
have the same 'feature' where the caller can ommit a cast
in the argument list and no cast occurs in the code. I'm
not sure how to keep the code condensed while keeping the
macros. Any advice would be appreciated.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Currently the fcoe_ctlr associated with an interface is allocated
as a member of struct bnx2fc_interface. This causes problems when
when later patches attempt to use the new fcoe_sysfs APIs which
allow us to allocate the bnx2fc_interface as private data to a
fcoe_ctlr_device instance. The problem is that libfcoe wants to
be able use pointer math to find a fcoe_ctlr's fcoe_ctlr_device
as well as finding a fcoe_ctlr_device's assocated fcoe_ctlr. To
do this we need to allocate the fcoe_ctlr_device, with private
data for the LLD. The private data will contain the fcoe_ctlr
and its private data will be the bnx2fc_interface.
+-------------------+
| fcoe_ctlr_device |
+-------------------+
| fcoe_ctlr |
+-------------------+
| bnx2fc_interface |
+-------------------+
This prep work will allow us to go from a fcoe_ctlr_device
instance to its fcoe_ctlr as well as from a fcoe_ctlr to its
fcoe_ctlr_device once the fcoe_sysfs API is in use (later
patches in this series).
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Currently the fcoe_ctlr associated with an interface is allocated
as a member of struct fcoe_interface. This causes problems when
attempting to use the new fcoe_sysfs APIs which allow us to allocate
the fcoe_interface as private data to the fcoe_ctlr_device instance.
The problem is that libfcoe wants to be able use pointer math to find a
fcoe_ctlr's fcoe_ctlr_device as well as finding a fcoe_ctlr_device's
assocated fcoe_ctlr. To do this we need to allocate the
fcoe_ctlr_device, with private data for the LLD. The private data
contains the fcoe_ctlr and its private data is the fcoe_interface.
This patch only allocates the fcoe_interface with the fcoe_ctlr, the
fcoe_ctlr_device will be added in a later patch, which will complete
the below diagram-
+------------------+
| fcoe_ctlr_device |
+------------------+
| fcoe_ctlr |
+------------------+
| fcoe_interface |
+------------------+
This prep work will allow us to go from a fcoe_ctlr_device instance
to its fcoe_ctlr as well as from a fcoe_ctlr to its fcoe_ctlr_device
once the fcoe_sysfs API is in use (later patches in this series).
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
block congestion control doesn't have any concept of fairness across
multiple queues. This means that if SCSI reports the host as busy in
the queue congestion control it can result in an unfair starvation
situation in dm-mp if there are multiple multipath devices on the same
host. For example:
http://www.redhat.com/archives/dm-devel/2012-May/msg00123.html
The fix for this is to report only the sdev busy state (and ignore the
host busy state) in the block congestion control call back.
The host is still congested, but the SCSI subsystem will sort out the
congestion in a fair way because it knows the relation between the
queues and the host.
[jejb: fixed up trailing whitespace]
Reported-by: Bernd Schubert <bernd.schubert@itwm.fraunhofer.de>
Tested-by: Bernd Schubert <bernd.schubert@itwm.fraunhofer.de>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Avoid dereferencing a NULL pointer if scsi_host_alloc is failed.
Signed-off-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial updates from Jiri Kosina:
"As usual, it's mostly typo fixes, redundant code elimination and some
documentation updates."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (57 commits)
edac, mips: don't change code that has been removed in edac/mips tree
xtensa: Change mail addresses of Hannes Weiner and Oskar Schirmer
lib: Change mail address of Oskar Schirmer
net: Change mail address of Oskar Schirmer
arm/m68k: Change mail address of Sebastian Hess
i2c: Change mail address of Oskar Schirmer
net: Fix tcp_build_and_update_options comment in struct tcp_sock
atomic64_32.h: fix parameter naming mismatch
Kconfig: replace "--- help ---" with "---help---"
c2port: fix bogus Kconfig "default no"
edac: Fix spelling errors.
qla1280: Remove redundant NULL check before release_firmware() call
remoteproc: remove redundant NULL check before release_firmware()
qla2xxx: Remove redundant NULL check before release_firmware() call.
aic94xx: Get rid of redundant NULL check before release_firmware() call
tehuti: delete redundant NULL check before release_firmware()
qlogic: get rid of a redundant test for NULL before call to release_firmware()
bna: remove redundant NULL test before release_firmware()
tg3: remove redundant NULL test before release_firmware() call
typhoon: get rid of redundant conditional before all to release_firmware()
...
|
|
In the original code, if dma_pool_alloc() fails then we call
dma_pool_free(). It causes an error, possibly a NULL dereference.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This patch adds support for tcm_qla2xxx fabric module for target-core
using the new qla_target.c LLD logic. This includes support for explict
NodeACLs via configfs using tcm_qla2xxx_setup_nacl_from_rport() from libfc
struct fc_host->rports, and demo-mode support for virtual LUN=0 access.
This patch also adds support for using tcm_qla2xxx_lport->lport_fcport_map
and ->lport_loopid_map of btree_head32 to track struct se_node_acl pointers
for individual 24-bit Port ID and 16-bit Loop ID values w/ qla_target_template
->find_sess_by_s_id() and ->find_sess_by_loop_id() used in a number of
locations into the primary I/O dispatch logic in qla_target.c LLD code.
The main piece for FC Nexus setup is in tcm_qla2xxx_check_initiator_node_acl(),
which calls tcm_qla2xxx_set_sess_by_[s_id,loop_id]() to setup our
lport->lport_fcport_map and lport_loopid_map pointers respectively, and
register the new nexus with TCM via __transport_register_session().
(nab: Add qla_tgt_mgmt_cmd usage with TARGET_SCF_ACK_KREF during TMRs +
change tcm_qla2xxx_nacl->nport_id to u32 (DanC))
(danc: tcm_qla2xxx: checking for NULL instead of IS_ERR())
(roland: Fix up v3.5 breakage for removal of transport_do_task_sg_chain +
Add hook so qla_target code can shutdown sessions)
(steveh: Convert FC address map from flat array to btree)
(randy: fix qla2xxx printk format warnings for size_t)
(joern: Make most of tcm_qla2xxx static + remove unnecessary
workqueue_struct prototypes + use WWN_SIZE instead of hard-coded
constants)
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Add LLD target mode for >= 24xx series HW. This code was originally based on
external qla2x00t module based on 8.02.01-k4, and has been refactored to
push the bulk of code into mainline qla2xxx.ko LLD -> qla_target.c.
The implementation uses internal workqueues for I/O context submission
into tcm_qla2xxx code, and includes the struct qla_tgt_func_tmpl API for
external interaction to allow qla2xxx LDD to function without direct
target-core dependencies:
It also enables qla_target.c usage within existing qla2xxx LLD code.
This includes:
*) Addition of target mode specific members to existing data
structures in qla_def.h and struct qla_hw_data->tgt_ops using
qla_target.h:struct qla_tgt_func_tmpl
*) Addition of struct qla_tgt_func_tmpl and direct calls into
qla_target.c logic w/ qlt_* prefixed functions.
*) Addition of qla_iocb.c:qla2x00_req_pkt() for ring processing, and
qla2x00_issue_marker() for handling request/response queue processing
for target mode operation
*) Addition of various qla_tgt_mode_enabled() logic checks in
qla24xx_nvram_config(), qla2x00_initialize_adapter(), qla2x00_rff_id(),
qla2x00_abort_isp(), qla24xx_modify_vp_config(), and
qla2x00_vp_abort_isp().
By default the new qlini_mode module parameter is setting initiator-mode
to 'enabled' in order for 'modprobe qla2xxx' to continue to function as
expected in initiator only mode. Enabling target-mode operation will
currently require a:
modprobe qla2xxx qlini_mode="disabled"
in order to explictly disabled initiator mode and allow target-mode
to be enabled via tcm_qla2xxx configfs fabric callers.
(nab: Convert to qlini_mode='enabled' by default in qla_target.c)
(joern: Remove loop_id from qla_tgt_make_local_sess() arguments +
Remove unused s_id + fix s_id endianness bug +
simplify qla_tgt_abort_work)
(gerard: fix section __exit mismatch in qla_tgt_exit)
(arun: Capture ATIO queue during firmware dump + Send SCR in target mode +
Target mode review comments)
(roland: Don't create duplicate target sessions to address tearing down
ACLs with IO in flight + Add missing call to qlt_fc_port_deleted
call during qla2x00_schedule_rport_del timeout)
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
commit 491118dff9aeb207408bd42aa4897bc2c145747f
Author: Saurav Kashyap <saurav.kashyap@qlogic.com>
Date: Tue Aug 16 11:31:50 2011 -0700
[SCSI] qla2xxx: During loopdown perform Diagnostic loopback.
The LOOP_DOWN test is not needed.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
is gathered for ISP82xx.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
application.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The field vp_idx in struct fc_port is a redundant/mirror copy of
the same field in struct scsi_qla_host;
struct fc_port has a pointer vha to scsi_qla_host which allows
the original copy of vp_idx to be readily accessed.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Nigel Kirkland <nigel.kirkland@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Both the target-id and LUN are munged in the original printk().
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
