| Age | Commit message (Collapse) | Author |
|---|
|
Made changes to FCS lport, vport state machines to support vport
enable / disable operations.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Added support for Brocade-1860 Fabric Adapter.
- Made changes to support single firmware image per asic type.
- Combined bfi_cbreg.h and bfi_ctreg.h defines into bfi_reg.h with
only minimal defines used by host.
- Added changes to setup CPE/RME Queue register offsets based on
firmware response.
- Removed queue register offset initializations and added register offsets
to BFI config response message.
- Added Brocade-1860 asic specific interrupt status definitions and
mailbox interfaces.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Add PBC port Disabled condition check.
- Rename incorrectly named LPS I2H messages.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Introduced a generic event notification callback function that
receives IOC_ENABLED, IOC_DISABLED, IOC_FAILED events and notifies the
modules registered for these events.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Avoid the use of hardware defined structure bfi_sge_s for DMA
requests in host.
- Defined a generic address len pair to represent a DMA memory chunk
(bfi_alen_s).
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This fixes:
drivers/scsi/sun3_NCR5380.c:475: warning: ‘merge_contiguous_buffers’ defined but not used
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Sam Creasey <sammy@sammy.net>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This fixes a.o.:
drivers/scsi/sun3_scsi.h:225:5: warning: "NDEBUG" is not defined
drivers/scsi/sun3_scsi.h:345:14: warning: "NDEBUG_ABORT" is not defined
drivers/scsi/sun3_scsi.h:351:14: warning: "NDEBUG_TAGS" is not defined
drivers/scsi/sun3_scsi.h:357:14: warning: "NDEBUG_MERGING" is not defined
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This fixes:
drivers/scsi/sun3_NCR5380.c:1448:5: warning: "NCR_TIMEOUT" is not defined
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
and call it from sun3scsi_release(), cfr. the other NCR5380 drivers.
This fixes:
drivers/scsi/NCR5380.h:303: warning: ‘NCR5380_exit’ declared ‘static’ but never defined
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
WARNING: vmlinux.o(.text+0x18545c): Section mismatch in reference from the function sun3scsi_detect() to the function .init.text:NCR5380_print_options()
WARNING: vmlinux.o(.text+0x18556c): Section mismatch in reference from the function sun3scsi_detect() to the function .init.text:NCR5380_print_options()
WARNING: vmlinux.o(.text+0x187692): Section mismatch in reference from the function sun3scsi_detect() to the function .init.text:NCR5380_print_options()
WARNING: vmlinux.o(.text+0x187770): Section mismatch in reference from the function sun3scsi_detect() to the function .init.text:NCR5380_print_options()
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This fixes:
drivers/scsi/mac_scsi.c:220:5: warning: "NDEBUG_ABORT" is not defined
drivers/scsi/mac_scsi.c:271:5: warning: "NDEBUG_ABORT" is not defined
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
WARNING: vmlinux.o(.text+0x1ecd3e): Section mismatch in reference from the function macscsi_detect() to the function .devinit.text:NCR5380_init()
WARNING: vmlinux.o(.text+0x1ecddc): Section mismatch in reference from the function macscsi_detect() to the function .init.text:NCR5380_print_options()
WARNING: vmlinux.o(.text+0x1ece60): Section mismatch in reference from the function macscsi_detect() to the function .init.text:NCR5380_print_options()
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
and call it from atari_scsi_release(), cfr. the other NCR5380 drivers.
This fixes:
drivers/scsi/NCR5380.h:303: warning: ‘NCR5380_exit’ declared ‘static’ but never defined
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Add ISA PNP IDs of the following cards to aha152x driver:
AVA-1502
AVA-1505
AHA-1510
AVA-1515
AHA-1520
AHA-1522
AHA-1530
AHA-1532
AIC-6360
(list from SCSI.INF file)
This makes my AHA-1530P card (has ADP3015 ID) work automatically.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This patch resulted from the discussion at
https://bugzilla.novell.com/show_bug.cgi?id=679277,
https://bugzilla.novell.com/show_bug.cgi?id=681840 .
Signed-off-by: Werner Fink <werner@novell.com>
Signed-off-by: Ankit Jain <jankit@suse.de>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Noticed that when the sysfs interface of the SCSI SES
driver was used to request a fault indication the LED
flashed but the buzzer didn't sound. So it was doing
what REQUEST IDENT (locate) should do.
Changelog:
- fix the setting of REQUEST FAULT for the device slot
and array device slot elements in the enclosure control
diagnostic page
- note the potentially defective code that reads the
FAULT SENSED and FAULT REQUESTED bits from the enclosure
status diagnostic page
The attached patch is against git/scsi-misc-2.6
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
commit 8ce7955aa52c37db1425ea4bd4edcfa67e253454 ("[SCSI] atari_NCR5380:
update_timeout removal") removed all users, but not the avtual variable.
Suggested-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Using the current NEXT() macro for both lvalues and rvalues gives:
In file included from drivers/scsi/sun3_scsi.c:623:
drivers/scsi/sun3_NCR5380.c: In function ‘NCR5380_queue_command_lck’:
drivers/scsi/sun3_NCR5380.c:993: warning: assignment discards qualifiers from pointer target type
drivers/scsi/sun3_NCR5380.c: In function ‘NCR5380_main’:
drivers/scsi/sun3_NCR5380.c:1147: warning: assignment discards qualifiers from pointer target type
drivers/scsi/sun3_NCR5380.c: In function ‘NCR5380_information_transfer’:
drivers/scsi/sun3_NCR5380.c:2277: warning: assignment discards qualifiers from pointer target type
drivers/scsi/sun3_NCR5380.c:2333: warning: assignment discards qualifiers from pointer target type
Change NEXT() to operate on rvalues only(), and introduce SET_NEXT() to
operate on lvalues, as is done in drivers/scsi/atari_NCR5380.c.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Deleting NPIV port causes a kernel panic when the NPIV port is in the same zone
as the physical port and shares the same LUN. This happens due to the fact that
vport destroy and unsolicited ELS are scheduled to run on the same workqueue,
and vport destroy destroys the lport and the unsolicited ELS tries to access
the invalid lport. This patch fixes this issue by maintaining a list of valid
lports and verifying if the lport is valid or not before accessing it.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Do not set io_req->sc_cmd to NULL until bnx2fc_unmap_sg_list() is called to
enable it to unmap the DMA mappings.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
interfaces
NIC partitioned interfaces reports the speed of 2500 which was not handled by
the driver.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Enabling DEBUG_STRICT_USER_COPY_CHECKS causes the following
warning:
In file included from arch/x86/include/asm/uaccess.h:573,
from include/linux/uaccess.h:5,
from include/linux/highmem.h:7,
from include/linux/pagemap.h:10,
from include/linux/blkdev.h:12,
from drivers/scsi/lpfc/lpfc_debugfs.c:21:
In function 'copy_from_user':
arch/x86/include/asm/uaccess_64.h:65:
warning: call to 'copy_from_user_overflow' declared with
attribute warning: copy_from_user() buffer size is not provably
correct
presumably due to buf_size being signed causing GCC to fail to
see that buf_size can't become negative.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
In certain circumstances, we can get an oops from a torn down device.
Most notably this is from CD roms trying to call scsi_ioctl. The root
cause of the problem is the fact that after scsi_remove_device() has
been called, the queue is fully torn down. This is actually wrong
since the queue can be used until the sdev release function is called.
Therefore, we add an extra reference to the queue which is released in
sdev->release, so the queue always exists.
Reported-by: Parag Warudkar <parag.lkml@gmail.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
|
Fix kernel-doc warnings in scsi_proc.c:
Warning(drivers/scsi/scsi_proc.c:390): No description found for parameter 'dev'
Warning(drivers/scsi/scsi_proc.c:390): No description found for parameter 'data'
Warning(drivers/scsi/scsi_proc.c:390): Excess function parameter 's' description in 'always_match'
Warning(drivers/scsi/scsi_proc.c:390): Excess function parameter 'p' description in 'always_match'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (60 commits)
[SCSI] lpfc 8.3.24: Extend BSG infrastructure and add link diagnostics
[SCSI] lpfc 8.3.24: Add resource extent support
[SCSI] lpfc 8.3.24: Add request-firmware support
[SCSI] lpfc 8.3.24: Add SR-IOV control
[SCSI] lpfc 8.3.24: Extended hardware support and support dump images
[SCSI] lpfc 8.3.24: Miscellaneous Fixes and Corrections
[SCSI] libsas: Add option for SATA soft reset
[SCSI] libsas: check dev->gone before submitting sata i/o
[SCSI] libsas: fix/amend device gone notification in sas_deform_port()
[SCSI] MAINTAINERS update for SCSI (new email address)
[SCSI] Fix Ultrastor asm snippet
[SCSI] osst: fix warning
[SCSI] osst: wrong index used in inner loop
[SCSI] aic94xx: world-writable sysfs update_bios file
[SCSI] MAINTAINERS: Add drivers/target/ entry
[SCSI] target: Convert TASK_ATTR to scsi_tcq.h definitions
[SCSI] target: Convert REPORT_LUNs to use int_to_scsilun
[SCSI] target: Fix task->task_execute_queue=1 clear bug + LUN_RESET OOPs
[SCSI] target: Fix bug with task_sg chained transport_free_dev_tasks release
[SCSI] target: Fix interrupt context bug with stats_lock and core_tmr_alloc_req
...
|
|
Extend BSG infrastructure and add link diagnostics:
- Removed unnecessary copies in handling pass-through mbox cmds.
- Add embedded SLI_CONFIG support for BSG.
- Add multibuffer support.
- Implemented the setting up and tearing down Lancer FC device for performing
internal and external loopback diagnostic tests.
- Implemented the driver support for performing new link diagnostic tests
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
|
This patch adds support for hardware that returns resource ids via
extents rather than contiguous ranges.
[jejb: checkpatch.pl fixes]
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
|
Add request-firmware support:
- Add support for request_firmware interface for INTF2 SLI4 ports.
- Add ability to reset SLI4 INTF2 ports.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
|
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
|
Extended hardware support and support dump images:
- Make the size to be MAILBOX_SYSFS_MAX (4096) so that it allows the maximum
sysfs binary access interface possible.
- Add ids and model names for new hardware
- Add capability of inducing SLI4 firmware dump obj file
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
|
Miscellaneous Fixes and Corrections
- Remove the memset in the lpfc_sli4_remove_rpi_hdrs call.
- Correct swapping of SGE word 2 relative to offset value
- Reorganize CQ and EQ usage to comply with SLI4 Specification.
- Expand the driver to check the rn bit. Only detect an error if the error bit
is set and the RN bit is NOT set.
- If mailbox completion code is not success AND the mailbox status is success,
then and only then will the driver overwrite the mailbox status.
- When driver initializing device, if the device is on a PCIe bus, set
PCI's "needs fundamental reset" bit so that EEH uses fundamental reset
instead of hot reset for recovery.
- Prevent driver from using new WWN when changed in firmware (until driver
reload)
- When HBA reports maximum SGE size > 0xffffffff (infinite), override
with 0x80000000.
- Fixed potential missed SLI4 device initialization failure conditions.
- Added 100ms delay before driver action following IF_TYPE_2 function reset.
- Reverted patch to UNREG/REG on PLOGI to mapped/unmapped node.
- Add a check for the CVL received flag in the fcf inuse routine to avoid
unregistering the fcf if Devloss fires before Delay discover timer fires.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
|
This allows a libsas driver to optionally provide a soft reset handler
for libata to drive. The isci driver allows software to control the
assertion/deassertion of SRST.
[jejb: checkpatch.pl fixes]
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
|
Head off doomed-to-fail i/o in sas_queuecommand before sending it down
the ata path.
Before:
sd 7:0:0:0: [sdd] Synchronizing SCSI cache
ata8: no sense translation for status: 0x00
ata8: translated ATA stat/err 0x00/00 to SCSI SK/ASC/ASCQ 0xb/00/00
ata8.00: device reported invalid CHS sector 0
ata8: status=0x00 { }
ata8: no sense translation for status: 0x00
ata8: translated ATA stat/err 0x00/00 to SCSI SK/ASC/ASCQ 0xb/00/00
ata8.00: device reported invalid CHS sector 0
ata8: status=0x00 { }
ata8: no sense translation for status: 0x00
ata8: translated ATA stat/err 0x00/00 to SCSI SK/ASC/ASCQ 0xb/00/00
ata8.00: device reported invalid CHS sector 0
ata8: status=0x00 { }
sd 7:0:0:0: [sdd] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
sd 7:0:0:0: [sdd] Sense Key : Aborted Command [current] [descriptor]
sd 7:0:0:0: [sdd] Add. Sense: No additional sense information
sd 7:0:0:0: [sdd] Stopping disk
After:
sd 9:0:0:0: [sdd] Synchronizing SCSI cache
sd 9:0:0:0: [sdd] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
sd 9:0:0:0: [sdd] Stopping disk
sd 9:0:0:0: [sdd] START_STOP FAILED
sd 9:0:0:0: [sdd] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
This is a cosmetic change as sata i/o can still leak to a gone device,
but this addresses the nominal hotplug case when releasing the target.
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
|
Commit 56dd2c06 "libsas: Don't issue commands to devices that have been
hot-removed" edited Darrick's original patch to remove setting 'gone' in
the sas_deform_port() path because that prevented scsi sync cache
commands from being issued when the driver was unloaded. However, this
allows true device gone notifications (as signaled port phy events) to
trigger sync cache commands to devices that are known to be unreachable.
Teach libsas which sas_deform_port() invocations are likely device gone
events.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6
* 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6:
gfs2: Drop __TIME__ usage
isdn/diva: Drop __TIME__ usage
atm: Drop __TIME__ usage
dlm: Drop __TIME__ usage
wan/pc300: Drop __TIME__ usage
parport: Drop __TIME__ usage
hdlcdrv: Drop __TIME__ usage
baycom: Drop __TIME__ usage
pmcraid: Drop __DATE__ usage
edac: Drop __DATE__ usage
rio: Drop __DATE__ usage
scsi/wd33c93: Drop __TIME__ usage
scsi/in2000: Drop __TIME__ usage
aacraid: Drop __TIME__ usage
media/cx231xx: Drop __TIME__ usage
media/radio-maxiradio: Drop __TIME__ usage
nozomi: Drop __TIME__ usage
cyclades: Drop __TIME__ usage
|
|
* 'for-2.6.40/core' of git://git.kernel.dk/linux-2.6-block: (40 commits)
cfq-iosched: free cic_index if cfqd allocation fails
cfq-iosched: remove unused 'group_changed' in cfq_service_tree_add()
cfq-iosched: reduce bit operations in cfq_choose_req()
cfq-iosched: algebraic simplification in cfq_prio_to_maxrq()
blk-cgroup: Initialize ioc->cgroup_changed at ioc creation time
block: move bd_set_size() above rescan_partitions() in __blkdev_get()
block: call elv_bio_merged() when merged
cfq-iosched: Make IO merge related stats per cpu
cfq-iosched: Fix a memory leak of per cpu stats for root group
backing-dev: Kill set but not used var in bdi_debug_stats_show()
block: get rid of on-stack plugging debug checks
blk-throttle: Make no throttling rule group processing lockless
blk-cgroup: Make cgroup stat reset path blkg->lock free for dispatch stats
blk-cgroup: Make 64bit per cpu stats safe on 32bit arch
blk-throttle: Make dispatch stats per cpu
blk-throttle: Free up a group only after one rcu grace period
blk-throttle: Use helper function to add root throtl group to lists
blk-throttle: Introduce a helper function to fill in device details
blk-throttle: Dynamically allocate root group
blk-cgroup: Allow sleeping while dynamically allocating a group
...
|
|
The presense of a writeq() implementation on 32-bit x86 that splits the
64-bit write into two 32-bit writes turns out to break the mpt2sas driver
(and in general is risky for drivers as was discussed in
<http://lkml.kernel.org/r/adaab6c1h7c.fsf@cisco.com>). To fix this,
revert 2c5643b1c5c7 ("x86: provide readq()/writeq() on 32-bit too") and
follow-on cleanups.
This unfortunately leads to pushing non-atomic definitions of readq() and
write() to various x86-only drivers that in the meantime started using the
definitions in the x86 version of <asm/io.h>. However as discussed
exhaustively, this is actually the right thing to do, because the right
way to split a 64-bit transaction is hardware dependent and therefore
belongs in the hardware driver (eg mpt2sas needs a spinlock to make sure
no other accesses occur in between the two halves of the access).
Build tested on 32- and 64-bit x86 allmodconfig.
Link: http://lkml.kernel.org/r/x86-32-writeq-is-broken@mdm.bga.com
Acked-by: Hitoshi Mitake <h.mitake@gmail.com>
Cc: Kashyap Desai <Kashyap.Desai@lsi.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Ravi Anand <ravi.anand@qlogic.com>
Cc: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Jason Uhlenkott <juhlenko@akamai.com>
Acked-by: James Bottomley <James.Bottomley@parallels.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
pcmcia: Make struct pcmcia_device_id const, sound drivers edition
staging: pcmcia: Convert pcmcia_device_id declarations to const
pcmcia: Convert pcmcia_device_id declarations to const
pcmcia: Make declaration and uses of struct pcmcia_device_id const
pcmcia/sa1100: put sa11x0_pcmcia_hw_init[] to .devinit.data
|
|
Commit 1292500b replaced
"=m" (*field) : "1" (*field)
with
"=m" (*field) :
with comment "The following patch fixes it by using the '+' operator on
the (*field) operand, marking it as read-write to gcc."
'+' was actually forgotten. This really puts it.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
|
drivers/scsi/osst.c: In function '__os_scsi_tape_open':
drivers/scsi/osst.c:4705: warning: ISO C90 forbids mixed declarations and code
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
|
Index i was already used in the outer loop. Fixes a potentially-infinite
loop.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Willem Riede <osst@riede.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
|
Don't allow everybody to load firmware.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
|
In error recovery, most scsi error recovery stages will send a TUR command
for every bad command when a driver's error handler reports success. When
several bad commands to the same device, this results in a device
being probed multiple times.
This becomes very problematic if the device or connection is in a state
where the device still doesn't respond to commands even after a recovery
function returns success. The error handler must wait for the test
commands to time out. The time waiting for the redundant commands can
drastically lengthen error recovery.
This patch alters the scsi mid-layer's error routines to send test commands
once per device instead of once per bad command. This can drastically
lower error recovery time.
[jejb: fixed up whitespace and formatting]
Signed-of-by: David Jeffery <djeffery@redhat.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
|
Some kernel transport drivers unconditionally disable
retrieval of the Caching mode page. One such for example is
the BBB/CBI transport over USB. Such a restraint is too
harsh as some devices do support the Caching mode
page. Unconditionally enabling the retrieval of this mode
page over those transports at their transport code level may
result in some devices failing and becoming unusable.
This patch implements a method of retrieving the Caching
mode page without unconditionally enabling it in the
transports which unconditionally disable it. The idea is to
ask for all supported pages, page code 0x3F, and then search
for the Caching mode page in the mode parameter data
returned. The sd driver already asks for all the mode pages
supported by the attached device by setting the page code to
0x3F in order to find out if the media is write protected by
reading the WP bit in the Device Specific Parameter
field. It then attempts to retrieve only the Caching mode
page by setting the page code to 8 and actually attempting
to retrieve it if and only if the transport allows it.
The method implemented here is that if the transport doesn't
allow retrieval of the Caching mode page and the device is
not RBC, then we ask for all pages supported by setting the
page code to 0x3F (similarly to how the WP bit is retrieved
above), and then we search for the Caching mode page in the
mode parameter data returned.
With this patch, devices over SATA, report this (no change):
Oct 22 18:45:58 localhost kernel: sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
Oct 22 18:45:58 localhost kernel: sd 0:0:0:0: Attached scsi generic sg0 type 0
Oct 22 18:45:58 localhost kernel: sd 0:0:0:0: [sda] Write Protect is off
Oct 22 18:45:58 localhost kernel: sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
Oct 22 18:45:58 localhost kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Smart devices report their Caching mode page. This is a
change where we'd previously see the kernel making
assumption about the device's cache being write-through:
Oct 22 18:45:58 localhost kernel: sd 6:0:0:0: Attached scsi generic sg2 type 0
Oct 22 18:45:58 localhost kernel: sd 6:0:0:0: [sdb] 610472646 4096-byte logical blocks: (2.50 TB/2.27 TiB)
Oct 22 18:45:58 localhost kernel: sd 6:0:0:0: [sdb] Write Protect is off
Oct 22 18:45:58 localhost kernel: sd 6:0:0:0: [sdb] Mode Sense: 47 00 10 08
Oct 22 18:45:58 localhost kernel: sd 6:0:0:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA
And "dumb" devices over BBB, are correctly shown not to
support reporting the Caching mode page:
Oct 22 18:49:06 localhost kernel: sd 7:0:0:0: [sdc] 15663104 512-byte logical blocks: (8.01 GB/7.46 GiB)
Oct 22 18:49:06 localhost kernel: sd 7:0:0:0: [sdc] Write Protect is off
Oct 22 18:49:06 localhost kernel: sd 7:0:0:0: [sdc] Mode Sense: 23 00 00 00
Oct 22 18:49:06 localhost kernel: sd 7:0:0:0: [sdc] No Caching mode page present
Oct 22 18:49:06 localhost kernel: sd 7:0:0:0: [sdc] Assuming drive cache: write through
Version 2 adds this:
Some devices don't support page code 0x3F, and others require a
fixed transfer length of 192 bytes. This single commit includes a
patch by Alan Stern which fixes this.
Reported-and-tested-by: Richard Senior <richard@r-senior.demon.co.uk>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Luben Tuikov <ltuikov@yahoo.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
|
Modified the event coalescing code for iSCSI offload to combat both
corner cases and optimize performance as follows:
1. Added mechanism to loop back a second time to process any leftover
CQEs that was generated by the hardware during the time the driver is
busy processing previous CQEs in the bh. This not only helps the
performance but also fixes the corner case when no more CQEs are being
generated in the pipeline; so those leftover CQEs will get a a chance
to be processed.
2. Added ARM_CQE_FP to distinguish between fast path arming versus
slow path arming. This change will guarantee that the CQEs will
always get a chance to be re-armed during fast path completions.
3. Removed the inline event coalescing division for perf optimization.
Also fixed a division-by-zero error when the event_coal_div module
param was set to 0.
4. Changed the default SQ WQEs size from 256 to 128 to match chip
default.
5. Changed the cmd_per_lun from 32 to 24.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
|
Modified the 10s wait time for inflight offload connections to
advance to the next state to 2s based on test result.
Modified the 20s shutdown timeout to 30s based on test result.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
|
The number of chip's internal command cell, which is use to generate
SCSI cmd packets to the target, was not initialized correctly by
the driver when the sq_size is changed from the default 128.
This, in turn, will create a problem where the chip's transmit pipe
will erroneously reuse an old command cell that is no longer valid.
The fix is to correctly initialize the chip's command cell upon setup.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
|
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
|
Added fw_version, serial_num, iscsi version and boot loader version
sysfs attributes.
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
