| Age | Commit message (Collapse) | Author |
|---|
|
Commit 18a4d0a22ed6 ("[SCSI] Handle disk devices which can not process
medium access commands") introduced a bug in which we would attempt to
dereference the scsi driver even when the device had no ULD attached.
Ensure that a driver is registered and make the driver accessor function
more resilient to errors during device discovery.
Reported-by: Elric Fu <elricfu1@gmail.com>
Reported-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Merge batch of fixes from Andrew Morton:
"The simple_open() cleanup was held back while I wanted for laggards to
merge things.
I still need to send a few checkpoint/restore patches. I've been
wobbly about merging them because I'm wobbly about the overall
prospects for success of the project. But after speaking with Pavel
at the LSF conference, it sounds like they're further toward
completion than I feared - apparently davem is at the "has stopped
complaining" stage regarding the net changes. So I need to go back
and re-review those patchs and their (lengthy) discussion."
* emailed from Andrew Morton <akpm@linux-foundation.org>: (16 patches)
memcg swap: use mem_cgroup_uncharge_swap fix
backlight: add driver for DA9052/53 PMIC v1
C6X: use set_current_blocked() and block_sigmask()
MAINTAINERS: add entry for sparse checker
MAINTAINERS: fix REMOTEPROC F: typo
alpha: use set_current_blocked() and block_sigmask()
simple_open: automatically convert to simple_open()
scripts/coccinelle/api/simple_open.cocci: semantic patch for simple_open()
libfs: add simple_open()
hugetlbfs: remove unregister_filesystem() when initializing module
drivers/rtc/rtc-88pm860x.c: fix rtc irq enable callback
fs/xattr.c:setxattr(): improve handling of allocation failures
fs/xattr.c:listxattr(): fall back to vmalloc() if kmalloc() failed
fs/xattr.c: suppress page allocation failure warnings from sys_listxattr()
sysrq: use SEND_SIG_FORCED instead of force_sig()
proc: fix mount -t proc -o AAA
|
|
Many users of debugfs copy the implementation of default_open() when
they want to support a custom read/write function op. This leads to a
proliferation of the default_open() implementation across the entire
tree.
Now that the common implementation has been consolidated into libfs we
can replace all the users of this function with simple_open().
This replacement was done with the following semantic patch:
<smpl>
@ open @
identifier open_f != simple_open;
identifier i, f;
@@
-int open_f(struct inode *i, struct file *f)
-{
(
-if (i->i_private)
-f->private_data = i->i_private;
|
-f->private_data = i->i_private;
)
-return 0;
-}
@ has_open depends on open @
identifier fops;
identifier open.open_f;
@@
struct file_operations fops = {
...
-.open = open_f,
+.open = simple_open,
...
};
</smpl>
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
Pull SCSI updates from James Bottomley:
"This is primarily another round of driver updates (lpfc, bfa, fcoe,
ipr) plus a new ufshcd driver. There shouldn't be anything
controversial in here (The final deletion of scsi proc_ops which
caused some build breakage has been held over until the next merge
window to give us more time to stabilise it).
I'm afraid, with me moving continents at exactly the wrong time,
anything submitted after the merge window opened has been held over to
the next merge window."
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (63 commits)
[SCSI] ipr: Driver version 2.5.3
[SCSI] ipr: Increase alignment boundary of command blocks
[SCSI] ipr: Increase max concurrent oustanding commands
[SCSI] ipr: Remove unnecessary memory barriers
[SCSI] ipr: Remove unnecessary interrupt clearing on new adapters
[SCSI] ipr: Fix target id allocation re-use problem
[SCSI] atp870u, mpt2sas, qla4xxx use pci_dev->revision
[SCSI] fcoe: Drop the rtnl_mutex before calling fcoe_ctlr_link_up
[SCSI] bfa: Update the driver version to 3.0.23.0
[SCSI] bfa: BSG and User interface fixes.
[SCSI] bfa: Fix to avoid vport delete hang on request queue full scenario.
[SCSI] bfa: Move service parameter programming logic into firmware.
[SCSI] bfa: Revised Fabric Assigned Address(FAA) feature implementation.
[SCSI] bfa: Flash controller IOC pll init fixes.
[SCSI] bfa: Serialize the IOC hw semaphore unlock logic.
[SCSI] bfa: Modify ISR to process pending completions
[SCSI] bfa: Add fc host issue lip support
[SCSI] mpt2sas: remove extraneous sas_log_info messages
[SCSI] libfc: fcoe_transport_create fails in single-CPU environment
[SCSI] fcoe: reduce contention for fcoe_rx_list lock [v2]
...
|
|
Usage of /etc/modprobe.conf file was deprecated by module-init-tools and
is no longer parsed by new kmod tool. References to this file are
replaced in Documentation, comments and Kconfig according to the
context.
There are also some references to the old /etc/modules.conf from 2.4
kernels that are being removed.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system
Pull "Disintegrate and delete asm/system.h" from David Howells:
"Here are a bunch of patches to disintegrate asm/system.h into a set of
separate bits to relieve the problem of circular inclusion
dependencies.
I've built all the working defconfigs from all the arches that I can
and made sure that they don't break.
The reason for these patches is that I recently encountered a circular
dependency problem that came about when I produced some patches to
optimise get_order() by rewriting it to use ilog2().
This uses bitops - and on the SH arch asm/bitops.h drags in
asm-generic/get_order.h by a circuituous route involving asm/system.h.
The main difficulty seems to be asm/system.h. It holds a number of
low level bits with no/few dependencies that are commonly used (eg.
memory barriers) and a number of bits with more dependencies that
aren't used in many places (eg. switch_to()).
These patches break asm/system.h up into the following core pieces:
(1) asm/barrier.h
Move memory barriers here. This already done for MIPS and Alpha.
(2) asm/switch_to.h
Move switch_to() and related stuff here.
(3) asm/exec.h
Move arch_align_stack() here. Other process execution related bits
could perhaps go here from asm/processor.h.
(4) asm/cmpxchg.h
Move xchg() and cmpxchg() here as they're full word atomic ops and
frequently used by atomic_xchg() and atomic_cmpxchg().
(5) asm/bug.h
Move die() and related bits.
(6) asm/auxvec.h
Move AT_VECTOR_SIZE_ARCH here.
Other arch headers are created as needed on a per-arch basis."
Fixed up some conflicts from other header file cleanups and moving code
around that has happened in the meantime, so David's testing is somewhat
weakened by that. We'll find out anything that got broken and fix it..
* tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system: (38 commits)
Delete all instances of asm/system.h
Remove all #inclusions of asm/system.h
Add #includes needed to permit the removal of asm/system.h
Move all declarations of free_initmem() to linux/mm.h
Disintegrate asm/system.h for OpenRISC
Split arch_align_stack() out from asm-generic/system.h
Split the switch_to() wrapper out of asm-generic/system.h
Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h
Create asm-generic/barrier.h
Make asm-generic/cmpxchg.h #include asm-generic/cmpxchg-local.h
Disintegrate asm/system.h for Xtensa
Disintegrate asm/system.h for Unicore32 [based on ver #3, changed by gxt]
Disintegrate asm/system.h for Tile
Disintegrate asm/system.h for Sparc
Disintegrate asm/system.h for SH
Disintegrate asm/system.h for Score
Disintegrate asm/system.h for S390
Disintegrate asm/system.h for PowerPC
Disintegrate asm/system.h for PA-RISC
Disintegrate asm/system.h for MN10300
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull a few more things for powerpc by Benjamin Herrenschmidt:
- Anton's did some recent improvements to EPOW event reporting on
pSeries (power supply failures and such). The patches are self
contained enough and replace really nasty code so I felt it should
still go in
- I did the vio driver registration change Greg requested, I don't see
the point of leaving that til the next merge window
- The remaining EEH changes I said were still pending to get rid of the
EEH references from the generic struct device_node
- A few more iSeries removal bits
- A perf bug fix on 970
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/perf: Fix instruction address sampling on 970 and Power4
powerpc+sparc/vio: Modernize driver registration
powerpc: Random little legacy iSeries removal tidy ups
powerpc: Remove NO_IRQ_IGNORE
powerpc/pseries: Cut down on enthusiastic use of defines in RAS code
powerpc/pseries: Clean up ras_error_interrupt code
powerpc/pseries: Remove RTAS_POWERMGM_EVENTS
powerpc/pseries: Use rtas_get_sensor in RAS code
powerpc/pseries: Parse and handle EPOW interrupts
powerpc: Make function that parses RTAS error logs global
powerpc/eeh: Retrieve PHB from global list
powerpc/eeh: Remove eeh information from pci_dn
powerpc/eeh: Remove eeh device from OF node
|
|
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it. Performed with the following command:
perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The latest generation of ipr hardware performs best when command blocks
are aligned to a boundary equal to the size of the command block. Ensure
512 byte alignment, since this is the largest size command block we
can send.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Increase the total number of max concurrent outstanding commands
for the most recent family of adapters in order to improve overall
adapter performance.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The ipr driver added some memory barriers in order to ensure
a PowerPC sync instruction was executed prior to sending a
command to the adapter to ensure the command block was
coherent with respect to the PCI bus's view of memory.
However, some time ago, the powerpc architecture writel
macros were changed to include the sync since most drivers
don't properly handle this. So remove these memory barriers
since they are not needed and result in executing twice
as many sync instructions, which has a significant performance
penalty.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The latest ipr hardware no longer requires the driver to issue any MMIOs
to clear the interrupt so remove this to optimize performance.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
For the latest ipr SAS adapters, target id's are a completely
logical construct that are managed in the ipr driver. This fixes
an issue that can arise if a device is deleted via sysfs. If
a new device is then physically added, it will use the previous
device's target id. If the host is then rescanned, the device
that had been deleted, since it is using the same target id as
the new device is using, will never be found, resulting in
a missing device. Fix this by only freeing the target id
only if the resource is actually gone.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
commit 44c10138fd4bbc4b6d6bff0873c24902f2a9da65 (PCI: Change all
drivers to use pci_device->revision) converted all drivers to use
pci_dev->revision. Convert these three drivers which got missed.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The rtnl_lock is primarily used to serialize networking
driver changes as well as to ensure that a networking driver
is not removed when making changes to it. fcoe also uses
the rtnl_lock to protect the fcoe hostlist.
fcoe_create holds the rtnl_lock over the entirity of the
routine including a the call to fcoe_ctlr_link_up.
This causes the below deadlock because fcoe_ctlr_link_up
acquires the fcoe_ctlr ctlr_mutex and this deadlocks with
a libfcoe thread that acquires the fcoe_ctlr ctlr_mutex and
then the rtnl_lock (to update a MAC address).
This patch drops the rtnl_lock before calling
fcoe_ctlr_link_up and therefore the deadlock is prevented.
https://bugzilla.kernel.org/show_bug.cgi?id=42918
the existing dependency chain (in reverse order) is:
-> #1 (&fip->ctlr_mutex){+.+...}:
[<c1091f70>] lock_acquire+0x80/0x1b0
[<c147655d>] mutex_lock_nested+0x6d/0x340
[<f8970c32>] fcoe_ctlr_link_up+0x22/0x180 [libfcoe]
[<f894620e>] fcoe_create+0x47e/0x6e0 [fcoe]
[<f8973dd3>] fcoe_transport_create+0x143/0x250 [libfcoe]
[<c10527e0>] param_attr_store+0x30/0x60
[<c1052696>] module_attr_store+0x26/0x40
[<c11a201e>] sysfs_write_file+0xae/0x100
[<c11449df>] vfs_write+0x8f/0x160
[<c1144cbd>] sys_write+0x3d/0x70
[<c147a0c4>] syscall_call+0x7/0xb
-> #0 (rtnl_mutex){+.+.+.}:
[<c109164b>] __lock_acquire+0x140b/0x1720
[<c1091f70>] lock_acquire+0x80/0x1b0
[<c147655d>] mutex_lock_nested+0x6d/0x340
[<c13a10c4>] rtnl_lock+0x14/0x20
[<f89445ac>] fcoe_update_src_mac+0x2c/0xb0 [fcoe]
[<f8971712>] fcoe_ctlr_timer_work+0x712/0xb60 [libfcoe]
[<c104fb69>] process_one_work+0x179/0x5d0
[<c10502f1>] worker_thread+0x121/0x2d0
[<c10550ed>] kthread+0x7d/0x90
[<c1481a82>] kernel_thread_helper+0x6/0x10
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&fip->ctlr_mutex);
lock(rtnl_mutex);
lock(&fip->ctlr_mutex);
lock(rtnl_mutex);
*** DEADLOCK ***
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Made changes to set the rport maxfrsize param to use a value that is
equal to or less than the Buffer-to-Buffer Receive Data_Field size
specified in the Common Service Parameters.
Increased the diag memtest timeout for the Brocade-1860 adapters.
Made changes to enable valid port speed configuration check for all adapters.
Made changes to increase the max hw segments in a request, in order to
support larger data transfers from user space.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Fixed the LPS (Logical Port Services) state machine to send a
FDISC/FLOGI to the FW from the request queue wait state, when
there is space available again on the request queue.
Made changes to free the vport on LOGO/cleanup complete instead
of free'ing it from vport_delete_handler in the module unload scenario.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Programming of the service parameters Tx credits etc., is now done in firmware.
Remove the logic of sending the service parameters to firmware from driver.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Made changes to the Fabric Assigned Address(FAA) feature implementation.
Introduced the IOCFC state machine, which now handles the FAA logic,
IOC and BFA sub-modules enablement.
Removed un-wanted FAA enable/disable routines; FAA is enabled by default.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Made changes to resume the flash controller if it is halted before going
ahead with flash controller pause/resume logic.
Made changes to avoid clearing off the interrupts during the initial
pll initialization.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Made changes to ensure only the function that comes first will execute
the IOC hw semaphore unlock logic.
Used IOC init sem register to serialize execution of the unlock logic.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Made changes to the driver ISR to process any pending completions even if
the RME bit is not set in the interrupt status register.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This fix ensures that the IOP_LOGINFO_CODE_TASK_TERMINATED
messages do not clutter the sas_log_info messages.
Bugzilla 42142 - mpt2sas: Number specified in wrong base
https://bugzilla.kernel.org/show_bug.cgi?id=42142
Signed-off-by: Sathisha Nanjappa <sathisha.nanjappa@hp.com>
Acked-by: "Nandigama, Nagalakshmi" <Nagalakshmi.Nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Starting fcoe fails at fcoe_transport_create when attempting to allocate a
pool of 4K exchanges on a 64-bit single-CPU environment because the call to
__alloc_percpu() is greater than the max of 32K. This patch reduces the
number of exchanges to fit within the maximum allowed space.
[ Whitespace problems fixed by Robert Love to satisfy chechpatch.pl ]
Signed-off-by: Steven Clark <sclark@crossbeam.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
There is potentially lots of contention for the rx_list_lock. On a cpu that is
receiving lots of fcoe traffic, the softirq context has to add and release the
lock for every frame it receives, as does the receiving per-cpu thread. We can
reduce this contention somewhat by altering the per-cpu threads loop such that
when traffic is detected on the fcoe_rx_list, we splice it to a temporary list.
In this way, we can process multiple skbs while only having to acquire and
release the fcoe_rx_list lock once.
[ Braces around single statement while loop removed by Robert Love
to satisfy checkpath.pl. ]
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
commit e7a51997dad4e17395be1209970e18d2e9305b24 ([SCSI] fcoe: flush per-cpu
thread work when destroying interface) added a skb flush to the fcoe_rx_list,
which ensures that we push any pending frames on the list through the per-cpu
receive thread. Because of this, its redundant to lock and scan the list
first, dropping any arriving frames.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
As with the fcoe sw transport, the bnx2fc packet handler function runs only in
softirq context. Theres no need to disable bottom halves here
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The fcoe sw recive packet function (fcoe_rcv) only ever executes in softirq
context. Given that, and the fact that no use of the fcoe_rx_list is made in
irq context, its not necessecary to disable bottom halves while actually
receiving the frame. Convert spin_*_bh calls in that function to their
lock-only equivalents
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Some switch implementations (eg., HP virtual connect FlexFabric) send two MAC
descriptors in FIP FLOGI response, with first MAC descriptor (granted_mac) used
as FPMA, and the second one (fcoe_mac) used as destination address for
sending/receiving FCoE packets. fip_mac continues to be used for FIP traffic.
This patch introduces fcoe_mac in fcoe_fcf structure. For regular switches,
both fcoe_mac and fip_mac will be the same. For the switches that send
additional MAC descriptor, fcoe_mac is updated.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Currently fc_host mfs is not getting updated in
case its changed during FLOGI and that leaves fc_host
to show its initial old value in sysfs, so instead
have fc_host mfs updated along with updating lport mfs
during FLOGI.
Also in case of bad mfs during flogi, error out
instead of continuing with flogi.
[ Changes made by Robert Love: condition to '>=' and
added printing of lport->mfs in DBG statement. FLOGI
resp processing failed without being able to compare
FCoE MFS 2112 against an incoming MFS of 2112 ]
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
When handling CVL with no Vx port descriptors, lports for NPIV ports are reset
before issuing the ctlr_reset. This causes FDISCs to be issued before
successful FLOGI. Fix it by resetting the controller before resetting the
lports.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
commit 859b7b649ab58ee5cbfb761491317d5b315c1b0f introduced the ability to call
fcoe_recv_frame in softirq context. While this is beneficial to performance,
its not safe to do, as it breaks the serialization of access to the lport
structure (i.e. when an fcoe interface is being torn down, theres no way to
serialize the teardown effort with the completion of receieve operations
occuring in softirq context. As a result, lport (and other) data structures can
be read and modified in parallel leading to corruption. Most notable is the
vport list, which is protected by a mutex, that will cause a panic if a softirq
receive while said mutex is locked. Additionaly, the ema_list, discussed here:
http://lists.open-fcoe.org/pipermail/devel/2012-February/011947.html
Can be corrupted if a list traversal occurs in softirq context at the same time
as a list delete in process context. And generally the lport state variables
will not be stable, and may lead to unpredictable results.
The most direct fix is to remove the bits from the above commit that allowed
fcoe_recv_frame to be called in softirq context. We just force all frames to be
handled by the per-cpu rx threads. This will allow the fcoe_if_destroy's use of
fcoe_percpu_clean to function properly, ensuring that no frames are being
received while the lport is being torn down.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reviewed-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Pull ARM platform updates from Russell King:
"This covers platform stuff for platforms I have a direct interest in
(iow, I have the hardware). Essentially:
- as we no longer support any other Acorn platforms other than RiscPC
anymore, we can collect all that code into mach-rpc.
- convert Acorn expansion card stuff to use IRQ allocation functions,
and get rid of NO_IRQ from there.
- cleanups to the ebsa110 platform to move some private stuff out of
its header files.
- large amount of SA11x0 updates:
- conversion of private DMA implementation to DMA engine support
(this actually gives us greater flexibility in drivers over the old
API.)
- re-worked ucb1x00 updates - convert to genirq, remove sa11x0
dependencies, fix various minor issues
- move platform specific sa11x0 framebuffer data into platform files
in arch/arm instead of keeping this in the driver itself
- update sa11x0 IrDA driver for DMA engine, and allow it to use DMA
for SIR transmissions as well as FIR
- rework sa1111 support for genirq, and irq allocation
- fix sa1111 IRQ support so it works again
- use sparse IRQ support
After this, I have one more pull request remaining from my current
set, which I think is going to be the most problematical as it
generates 8 conflicts."
Fixed up the trivial conflict in arch/arm/mach-rpc/Makefile as per
Russell.
* 'platforms' of git://git.linaro.org/people/rmk/linux-arm: (125 commits)
ARM: 7343/1: sa11x0: convert to sparse IRQ
ARM: 7342/2: sa1100: prepare for sparse irq conversion
ARM: 7341/1: input: prepare jornada720 keyboard and ts for sa11x0 sparse irq
ARM: 7340/1: rtc: sa1100: include mach/irqs.h instead of asm/irq.h
ARM: sa11x0: remove unused DMA controller definitions
ARM: sa11x0: remove old SoC private DMA driver
USB: sa1111: add hcd .reset method
USB: sa1111: add OHCI shutdown methods
USB: sa1111: reorganize ohci-sa1111.c
USB: sa1111: get rid of nasty printk(KERN_DEBUG "%s: ...", __FILE__)
USB: sa1111: sparse and checkpatch cleanups
ARM: sa11x0: don't static map sa1111
ARM: sa1111: use dev_err() rather than printk()
ARM: sa1111: cleanup sub-device registration and unregistration
ARM: sa1111: only setup DMA for DMA capable devices
ARM: sa1111: register sa1111 devices with dmabounce in bus notifier
ARM: sa1111: move USB interface register definitions to ohci-sa1111.c
ARM: sa1111: move PCMCIA interface register definitions to sa1111_generic.c
ARM: sa1111: move PS/2 interface register definitions to sa1111p2.c
ARM: sa1111: delete unused physical GPIO register definitions
...
|
|
This makes vio_register_driver() get the module owner & name at compile
time like PCI drivers do, and adds a name pointer directly in struct
vio_driver to avoid having to explicitly initialize the embedded
struct device.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David S. Miller <davem@davemloft.net>
|
|
Fetch the config page from the device to learn max target id to set
host->max_id.
Also, fix some indentation issues and update the 'Maintained by' field.
Signed-off-by: Arvind Kumar <arvindkumar@vmware.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The page length for the 0xb2 VPD page is defined to be 4 bytes when no
provisioning descriptors are provided (DP=0).
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Add LBPRZ support to scsi_debug; i.e. read zeros for
unmapped blocks.
Rather than checking for unmapped blocks at
read time, this just zeroes them on the backing store
at unmap time so it behaves the same way.
This also adds a module parameter to disable it.
lbprz, "unmapped blocks return 0 on read (def=1)"
[jejb: fix whitespace errors]
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
If a ping or host event were to occur when memory is low
we do not want to use GFP_KERNEL, because the paths
sending them cannot block for data to be written. These
paths might be needed to recover write paths. Use GFP_NOIO
instead.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Casting pointer from native data type to other type is
endian-sensitive.
"iocmd->offset" is 64 bit but we use only first 32 bit.
It works in little-endian system but in big-endian system
it will break.
Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com>
Acked-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Defined error codes for ping completion status.
This patch take care of Mike Christie's commets
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The st tape driver recently added the MTWEOFI ioctl, which writes
a tape filemark (EOF), like the MTWEOF ioctl, except that MTWEOFI
returns immediately. This makes certain applications, like backup
software, run much more quickly on buffered tape drives.
Since legacy applications do not know about this new MTWEOFI ioctl,
this patch adds a new ioctl option that tells the st driver to return
immediately when writing an EOF (i.e. a filemark). This new flag
is much like the existing flag that tells the st driver to perform
writes (and certain other IOs) immediately, but this new flag only
applies to writing EOFs.
This new feature is controlled via the MTSETDRVBUFFER ioctl, using
the newly-defined MT_ST_NOWAIT_EOF flag.
Use of this new feature is displayed via the sysfs tape "options"
attribute.
The st documentation was updated to mention this new flag, as well
as the problems that can occur from using it.
Signed-off-by: Lee Duncan <lduncan@suse.com>
Acked-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
