| Age | Commit message (Collapse) | Author |
|---|
|
After the patch "spi/s3c64xx: Fix non-dmaengine usage"
with commit id 563b444e33810f3120838620c990480304e24e63
submitted by Mark Brown, the spi device detection in polling
mode breaks. This revealed the missing check for polling during
dma prepare. This patch adds the missing check.
Signed-off-by: Girish K S <ks.giri@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
|
|
|
|
|
|
This should work with modern compilers, isn't that much of an issue if
it goes wrong and it ensures that the DT-only hardware variants don't
leave unreferenced parameters structures lying around.
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
This patch adds support for the exynos5440 spi controller.
The integration of the spi IP in exynos5440 is different from
other SoC's. The I/O pins are no more configured via gpio, they
have dedicated pins.
Signed-off-by: Girish K S <ks.giri@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The existing driver supports gpio based /cs signal.
For controller's that have one device per controller,
the slave device's /cs signal might be internally controlled
by the chip select bit of slave select register. They are not
externally asserted/deasserted using gpio pin.
This patch adds support for controllers with dedicated /cs pin.
if "cs-gpio" property doesnt exist in a spi dts node, the controller
would treat the /cs pin as dedicated.
Signed-off-by: Girish K S <ks.giri@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The 64xx spi driver supports partial polling mode.
Only the last chunk of the transfer length is transferred
or recieved in polling mode.
Some SoC's that adopt this controller might not have have dma
interface. This patch adds support for complete polling mode
and gives flexibity for the user to select poll/dma mode.
Signed-off-by: Girish K S <ks.giri@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
If the device is already in a runtime PM enabled state
pm_runtime_get_sync() will return 1, so a test for negative
value should be used to check for errors.
Without this patch there are seen errors like:
[ 8.540000] s3c64xx-spi 13930000.spi: Failed to enable device: 1
[ 8.545000] spi_master spi1: failed to prepare transfer hardware
Likely because the driver uses synchronous API to runtime enable
the device and asynchronous one to disable it.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mark Brown <broonielinaro.org>
Cc: stable@vger.kernel.org
|
|
Fill in the recently added spi_master.bits_per_word_mask field in as
many drivers as possible. Make related cleanups, such as removing any
redundant error-checking, or empty setup callbacks.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d0631001288a5974afc0b2a5f568bcdecb4d
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Don't silently ignore errors, report them.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The multiplatform conversion in commit 788437 (spi: s3c64xx: move to
generic dmaengine API) tested for the use of the Samsung-specific DMA
API with SAMSUNG_DMADEV when in fact S3C_DMA should be used. This
renderd DMA based transfers non-functional on platforms not using
dmaengine.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
With device core now able to setup the default pin configuration,
the pin configuration code based on the deprecated Samsung specific
gpio bindings is removed.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
|
The spi-s3c64xx uses a Samsung proprietary interface for
talking to the DMA engine, which does not work with
multiplatform kernels.
This version of the patch leaves the old code in place,
behind an #ifdef. This can be removed in the future,
after the s3c64xx platform start supporting the regular
dmaengine interface. An earlier version of this patch was
tested successfully on exynos5250 by Padma Venkat.
The conversion was rather mechanical, since the samsung
interface is just a shallow wrapper around the dmaengine
interface.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SET_SYSTEM_SLEEP_PM_OPS are only used
when the CONFIG_PM_SLEEP is enabled.
drivers/spi/spi-s3c64xx.c:1362:12: warning: 's3c64xx_spi_suspend' defined but not used [-Wunused-function]
drivers/spi/spi-s3c64xx.c:1381:12: warning: 's3c64xx_spi_resume' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
|
|
The core can do the validation for us.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The status of the interrupt is available in the status register,
so reading the clear pending register and writing back the same
value will not actually clear the pending interrupts. This patch
modifies the interrupt handler to read the status register and
clear the corresponding pending bit in the clear pending register.
Modified the hwInit function to clear all the pending interrupts.
Signed-off-by: Girish K S <ks.giri@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
|
|
The pointer to the driver data is never used to get the slave
controller data. We can delete the unused argument from the function.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg Kroah-Hartman:
"Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers
all over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
Other than those patches, there's not much here, some minor fixes and
updates"
Fix up trivial conflicts
* tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (221 commits)
base: memory: fix soft/hard_offline_page permissions
drivercore: Fix ordering between deferred_probe and exiting initcalls
backlight: fix class_find_device() arguments
TTY: mark tty_get_device call with the proper const values
driver-core: constify data for class_find_device()
firmware: Ignore abort check when no user-helper is used
firmware: Reduce ifdef CONFIG_FW_LOADER_USER_HELPER
firmware: Make user-mode helper optional
firmware: Refactoring for splitting user-mode helper code
Driver core: treat unregistered bus_types as having no devices
watchdog: Convert to devm_ioremap_resource()
thermal: Convert to devm_ioremap_resource()
spi: Convert to devm_ioremap_resource()
power: Convert to devm_ioremap_resource()
mtd: Convert to devm_ioremap_resource()
mmc: Convert to devm_ioremap_resource()
mfd: Convert to devm_ioremap_resource()
media: Convert to devm_ioremap_resource()
iommu: Convert to devm_ioremap_resource()
drm: Convert to devm_ioremap_resource()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"The biggest change in this update is the unification of HD-audio codec
parsers. Now the HD-audio codec is parsed in a generic parser code
which is invoked by each HD-audio codec driver.
Some background information is found in David Henningsson's blog
entry:
http://voices.canonical.com/david.henningsson/2013/01/18/upcoming-changes-to-the-intel-hda-drivers/
Other than that, some random updates/fixes like USB-audio and a bunch
of small AoC updates as usual.
Highlights:
- Unification of HD-audio parser code (aka generic parser)
- Support of new Intel HD-audio controller, new IDT codecs
- Fixes for HD-audio HDMI audio hotplug
- Haswell HDMI audio fixup
- Support of Creative CA0132 DSP code
- A few fixes of HDSP driver
- USB-audio fix for Roland A-PRO, M-Audio FT C600
- Support PM for aloop driver (and fixes Oops)
- Compress API updates for gapless playback support
For ASoC part:
- Support for a wider range of hardware in the compressed stream code
- The ability to mute capture streams as well as playback streams
while inactive
- DT support for AK4642, FSI, Samsung I2S and WM8962
- AC'97 support for Tegra
- New driver for max98090, replacing the stub which was there
- A new driver from Dialog
Note that due to dependencies, DTification of DMA support for Samsung
platforms (used only by the and I2S driver and SPI) is merged here as
well."
Fix up trivial conflict in drivers/spi/spi-s3c64xx.c due to removed code
being changed.
* tag 'sound-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (453 commits)
ALSA: usb: Fix Processing Unit Descriptor parsers
ALSA: hda - hdmi: Notify userspace when ELD control changes
ALSA: hda - hdmi: Protect ELD buffer
ALSA: hda - hdmi: Refactor hdmi_eld into parsed_hdmi_eld
ALSA: hda - hdmi: Do not expose eld data when eld is invalid
ALSA: hda - hdmi: ELD shouldn't be valid after unplug
ALSA: hda - Fix the silent speaker output on Fujitsu S7020 laptop
ALSA: hda - add quirks for mute LED on two HP machines
ALSA: usb/quirks, fix out-of-bounds access
ASoC: codecs: Add da7213 codec
ALSA: au88x0 - Define channel map for au88x0
ALSA: compress: add support for gapless playback
ALSA: hda - Remove speaker clicks on CX20549
ALSA: hda - Disable runtime PM for Intel 5 Series/3400
ALSA: hda - Increase badness for missing multi-io
ASoC: arizona: Automatically manage input mutes
ALSA: hda - Fix broken workaround for HDMI/SPDIF conflicts
ALSA: hda/ca0132 - Add missing \n to debug prints
ALSA: hda/ca0132 - Fix type of INVALID_CHIP_ADDRESS
ALSA: hda - update documentation for no-primary-hp fixup
...
|
|
Some of the spi driver module remove hooks were annotated with __exit
and referenced with __exit_p(). Presumably these were supposed to be
__devinit, __devexit and __devexit_p() since __init/__exit for a
probe/remove hook has never been correct. They also got missed during
the big __devinit/__devexit purge since they didn't match the pattern.
Remove then now to be rid of it.
v2: purge __init also
Reported-by: Arnd Bergmann <arnd@arndb.de>
[Arnd set a patch cleaning up one, and then I found more]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Fix checkpatch warnings and error as below:
ERROR: "foo * bar" should be "foo *bar"
WARNING: please, no space before tabs
WARNING: quoted string split across lines
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Use devm_clk_get() and devm_request_irq() rather than clk_get() and
request_irq() to make cleanup paths more simple.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc.git
Minor features and bug fixes for PXA, OMAP and GPIO deivce drivers and a
cosmetic change to the bitbang driver.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
The spi core make sure that each transfer structure have the proper
setting for bits_per_word before calling low level transfer APIs.
Hence it is no more require to check again in low level driver for
this field whether this is set correct or not. Removing such code
from low level driver.
The txx9 change also removes a test for bits_per_word set to 0, and
forcing it to 8 in that case. This can also be removed now since
spi_setup() ensures spi->bits_per_word is not zero.
if (!spi->bits_per_word)
spi->bits_per_word = 8;
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
This patch modifies the SPI driver to use generic dma dt bindings
support. This passes all the required arguments to dma dev request
functon which in turn calls the dma_request_slave_channel or dma__
request_channel based on DT or non-DT respectively.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Setting SW_RST does TX/RX FIFO flush.
After FIFO flush, SW_RST should be cleared.
The above setting and clearing SW_RST operation should be done after spi channel off.
Signed-off-by: Kyoungil Kim <ki0351.kim@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
During all transfers in one message, the device will not be chagned.
So we don't need to deassert chipselect during one message.
Signed-off-by: Kyoungil Kim <ki0351.kim@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Bill Pemberton has done most of the legwork on this series. I've used
his script to purge the attributes from the drivers/gpio tree.
Reported-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
|
|
The SPI driver makes a gpio_request during initialization. The requested
gpios need to be populated as part of the s3c64xx_spi_driver_data so that
they can be released during suspend and requested again during resume.
Add the missing code to save the requested gpios as part of the driver
data. This fixes a SPI driver suspend crash.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into fixes
A collection of warning fixes on non-ARM code from Arnd Bergmann:
* 'testing/driver-warnings' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: s3c: mark s3c2440_clk_add as __init_refok
spi/s3c64xx: use correct dma_transfer_direction type
pcmcia: sharpsl: don't discard sharpsl_pcmcia_ops
USB: EHCI: mark ehci_orion_conf_mbus_windows __devinit
mm/slob: use min_t() to compare ARCH_SLAB_MINALIGN
SCSI: ARM: make fas216_dumpinfo function conditional
SCSI: ARM: ncr5380/oak uses no interrupts
|
|
There is a subtle difference between dma_transfer_direction and
dma_data_direction: the former is used by the dmaengine framework,
while the latter is used by the dma-mapping API. Although the
purpose is comparable, the actual values are different and must
not be mixed. In this case, the driver just wants to use
dma_transfer_direction.
Without this patch, building s3c6400_defconfig results in:
drivers/spi/spi-s3c64xx.c: In function 's3c64xx_spi_dmacb':
drivers/spi/spi-s3c64xx.c:239:21: warning: comparison between
'enum dma_data_direction' and 'enum dma_transfer_direction' [-Wenum-compare]
As pointed out by Kukjin Kim, this also changes the use of constants
from DMA_FROM_DEVICE/DMA_TO_DEVICE to DMA_DEV_TO_MEM/DMA_MEM_TO_DEV.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: spi-devel-general@lists.sourceforge.net
|
|
Convert clk_enable/clk_disable to clk_prepare_enable/clk_disable_unprepare
calls as required by common clock framework.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Pull devicetree updates from Rob Herring:
- Import of latest upstream device tree compiler (dtc)
- New function of_get_child_by_name
- Support for #size-cells of 0 and #addr-cells of >2
- Couple of DT binding documentation updates
Fix up trivial conflicts due to of_get_child_by_name() having been added
next to the new of_get_next_available_child().
* tag 'dt-for-3.7' of git://sources.calxeda.com/kernel/linux:
MAINTAINERS: add scripts/dtc under Devicetree maintainers
dtc: import latest upstream dtc
dt: Document general interrupt controller bindings
dt/s3c64xx/spi: Use of_get_child_by_name to get a named child
dt: introduce of_get_child_by_name to get child node by name
of: i2c: add support for wakeup-source property
of/address: Handle #address-cells > 2 specially
DT: export of_irq_to_resource_table()
devicetree: serial: Add documentation for imx serial
devicetree: pwm: mxs-pwm.txt: Fix reg field annotation
of: Allow busses with #size-cells=0
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc
Pull spi updates from Mark Brown:
"No framework work here, only a bunch of driver updates of varying
sizes:
- Factoring out of the core hardware support from the MXS MMC driver
by Marek Vasut to allow the hardware to also be used for SPI.
- Lots of error handling cleanups from Guenter Roeck
- Removal of the existing Tegra driver which is quite comprehensively
broken as detailed in the changelog for the removal.
- DT suppport for the PL022 and GPIO drivers.
- pinctrl support for OMAP and PL022."
Pulling from Mark Brown as Grant Likely is still busy moving.
* tag 'spi-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc: (53 commits)
spi: remove completely broken Tegra driver
spi/imx: set the inactive state of the clock according to the clock polarity
spi/pl022: get/put resources on suspend/resume
spi/pl022: use more managed resources
spi/pl022: Devicetree support w/o platform data
spi/s3c64xx: Don't free controller_data on non-dt platforms
spi: omap2-mcspi: add pinctrl support
spi/pl022: adopt pinctrl support
spi: omap2-mcspi: Cleanup the omap2_mcspi_txrx_dma function
spi/gpio: Fix stub for spi_gpio_probe_dt()
spi/mxs: Make the SPI block clock speed configurable via DT
spi: spi-sh-hspi: drop frees of devm_ alloc'd data
spi/pl022: Fix chipselects pointer computation
spi: spi-tle62x0: Use module_spi_driver macro
mxs/spi: Rework the mxs_ssp_timeout to be more readable
mxs/spi: Decrement the DMA/PIO border
mxs/spi: Increment the transfer length only if transfer succeeded
mxs/spi: Fix issues when doing long continuous transfer
spi: spi-gpio: Add DT bindings
spi: spi-gpio: store chipselect information in private structure
...
|
|
As follow-up to "dt: introduce of_get_child_by_name to get child node by
name." patch, This patch removes some of the code duplication in the
driver by replacing it with of_get_child_by_name instead.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
|
|
Linux 3.6-rc6
Conflicts:
drivers/spi/spi-omap2-mcspi.c
|
|
When s3c64xx-spi is instantiated from device tree an instance of
struct s3c64xx_spi_csinfo is dynamically allocated in the driver.
For non-dt platform it is passed from board code through
spi_register_board_info(). On error path in s3c64xx_spi_setup()
function there is an attempt to free this data struct
s3c64xx_spi_csinfo object as it would have been allocated in the
driver for both, dt and non-dt based platforms. This leads to
following bug when gpio request fails:
spi spi1.0: Failed to get /CS gpio [21]: -16
kernel BUG at mm/slub.c:3478!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 Not tainted (3.6.0-rc5-00092-g9b0b493-dirty #6111)
PC is at kfree+0x148/0x158
LR is at s3c64xx_spi_setup+0xac/0x290
pc : [<c00a513c>] lr : [<c0227014>] psr: 40000013
sp : ee043e10 ip : c032883c fp : c0481f7c
r10: ee0abd80 r9 : 00000063 r8 : 00000000
r7 : ee129e78 r6 : ee104a00 r5 : fffffff0 r4 : c047bc64
r3 : 40000400 r2 : c047bc64 r1 : c04def60 r0 : 0004047b
Flags: nZcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 10c5387d Table: 4000404a DAC: 00000015
Process swapper/0 (pid: 1, stack limit = 0xee0422f0)
Stack: (0xee043e10 to 0xee044000)
...
[<c00a513c>] (kfree+0x148/0x158) from [<c0227014>] (s3c64xx_spi_setup+0xac/0x290)
[<c0227014>] (s3c64xx_spi_setup+0xac/0x290) from [<c02251a4>] (spi_setup+0x34/0x4c)
[<c02251a4>] (spi_setup+0x34/0x4c) from [<c02258d0>] (spi_add_device+0x98/0x128)
[<c02258d0>] (spi_add_device+0x98/0x128) from [<c02259d4>] (spi_new_device+0x74/0xa8)
[<c02259d4>] (spi_new_device+0x74/0xa8) from [<c0225a2c>] (spi_match_master_to_boardinfo+0x24/0x44)
[<c0225a2c>] (spi_match_master_to_boardinfo+0x24/0x44) from [<c0225b40>] (spi_register_master+0xf4/0x2a8)
[<c0225b40>] (spi_register_master+0xf4/0x2a8) from [<c043fe0c>] (s3c64xx_spi_probe+0x34c/0x42c)
[<c043fe0c>] (s3c64xx_spi_probe+0x34c/0x42c) from [<c01fc198>] (platform_drv_probe+0x18/0x1c)
There should be no attempt to kfree controller_data when it was
externally provided through the board code. Fix this by freeing
controller_data only when dev->of_node is not null.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the samsung include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Bryan Wu <bryan.wu@canonical.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: linux-samsung-soc@vger.kernel.org
|
|
Suspend and resume functions call spi_master_get() without matching
spi_master_put(). The extra references are unnecessary and cause subsequent
module unload attempts to fail. Drop the calls.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc
Pull spi fixes from Mark Brown:
"Grant is still away so another pull request with some fairly minor
fixes, the most notable of which are several fixes for some common
error patterns with the reference counting spi_master_get/put do."
* tag 'spi-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc:
spi/coldfire-qspi: Drop extra calls to spi_master_get in suspend/resume functions
spi: spi-coldfire-qspi: Drop extra spi_master_put in device remove function
spi/pl022: fix spi-pl022 pm enable at probe
spi/bcm63xx: Ensure that memory is freed only after it is no longer used
spi: omap2-mcspi: Fix the error handling in probe
spi/s3c64xx: Add missing static storage class specifiers
|
|
When a device tree definition os an s3c64xx SPI master is missing
a "controller-data" subnode, the newly added s3c64xx_get_slave_ctrldata
function might use uninitialized memory in place of that node,
which was correctly reported by gcc.
Without this patch, building s3c6400_defconfig results in:
drivers/spi/spi-s3c64xx.c: In function 's3c64xx_get_slave_ctrldata.isra.25':
drivers/spi/spi-s3c64xx.c:841:5: warning: 'data_np' may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Jaswinder Singh <jaswinder.singh@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
|
|
Silences the following sparse warnings:
drivers/spi/spi-s3c64xx.c:1482:32: warning:
symbol 's3c2443_spi_port_config' was not declared. Should it be static?
drivers/spi/spi-s3c64xx.c:1489:32: warning:
symbol 's3c6410_spi_port_config' was not declared. Should it be static?
drivers/spi/spi-s3c64xx.c:1495:32: warning:
symbol 's5p64x0_spi_port_config' was not declared. Should it be static?
drivers/spi/spi-s3c64xx.c:1501:32: warning:
symbol 's5pc100_spi_port_config' was not declared. Should it be static?
drivers/spi/spi-s3c64xx.c:1508:32: warning:
symbol 's5pv210_spi_port_config' was not declared. Should it be static?
drivers/spi/spi-s3c64xx.c:1515:32: warning:
symbol 'exynos4_spi_port_config' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
