| Age | Commit message (Collapse) | Author |
|---|
|
|
|
This reverts commit e120cc0dcf2880a4c5c0a6cb27b655600a1cfa1d.
It causes a NULL pointer dereference with drivers using the generic
spi_transfer_one_message(), which always calls
spi_finalize_current_message(), which zeroes master->cur_msg.
Drivers implementing transfer_one_message() theirselves must always call
spi_finalize_current_message(), even if the transfer failed:
* @transfer_one_message: the subsystem calls the driver to transfer a single
* message while queuing transfers that arrive in the meantime. When the
* driver is finished with this message, it must call
* spi_finalize_current_message() so the subsystem can issue the next
* transfer
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A respun version of the merges for the pull request previously sent
with a few additional fixes. The last two merges were fixed up by
hand since the branches have moved on and currently have the prior
merge in them.
Quite a busy release for the SPI subsystem, mostly in cleanups big and
small scattered through the stack rather than anything else:
- New driver for the Broadcom BC63xx HSSPI controller
- Fix duplicate device registration for ACPI
- Conversion of s3c64xx to DMAEngine (this pulls in platform and DMA
changes upon which the transiton depends)
- Some small optimisations to reduce the amount of time we hold locks
in the datapath, eliminate some redundant checks and the size of a
spi_transfer
- Lots of fixes, cleanups and general enhancements to drivers,
especially the rspi and Atmel drivers"
* tag 'spi-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (112 commits)
spi: core: Fix transfer failure when master->transfer_one returns positive value
spi: Correct set_cs() documentation
spi: Clarify transfer_one() w.r.t. spi_finalize_current_transfer()
spi: Spelling s/finised/finished/
spi: sc18is602: Convert to use bits_per_word_mask
spi: Remove duplicate code to set default bits_per_word setting
spi/pxa2xx: fix compilation warning when !CONFIG_PM_SLEEP
spi: clps711x: Add MODULE_ALIAS to support module auto-loading
spi: rspi: Add missing clk_disable() calls in error and cleanup paths
spi: rspi: Spelling s/transmition/transmission/
spi: rspi: Add support for specifying CPHA/CPOL
spi/pxa2xx: initialize DMA channels to -1 to prevent inadvertent match
spi: rspi: Add more QSPI register documentation
spi: rspi: Add more RSPI register documentation
spi: rspi: Remove dependency on DMAE for SHMOBILE
spi/s3c64xx: Correct indentation
spi: sh: Use spi_sh_clear_bit() instead of open-coded
spi: bitbang: Grammar s/make to make/to make/
spi: sh-hspi: Spelling s/recive/receive/
spi: core: Improve tx/rx_nbits check comments
...
|
|
|
|
|
|
master->transfer_one returns positive value is not a error.
So set ret to 0 when master->transfer_one returns positive value.
Otherwise, I hit "spi_master spi0: failed to transfer one message from queue"
error when my transfer_one callback returns 1.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
ACPI enumerated devices has ACPI style _HID and _CID strings,
all of these strings can be used for both driver loading and matching.
Currently, in Platform, I2C and SPI bus, the ACPI style driver matching
is supported by invoking acpi_driver_match_device() in bus .match() callback.
But, the module autoloading is still broken.
For example, there is any ACPI device with _HID "INTABCD" that is
enumerated to platform bus, and we have a driver that can probe it.
The driver exports its module_alias as "acpi:INTABCD" use the following code
static const struct acpi_device_id xxx_acpi_match[] = {
{ "INTABCD", 0 },
{ }
};
MODULE_DEVICE_TABLE(acpi, xxx_acpi_match);
But, unfortunately, the device' modalias is shown as "platform:INTABCD:00",
please refer to modalias_show() and platform_uevent() in
drivers/base/platform.c.
This results in that the driver will not be loaded automatically when the
device node is created, because their modalias do not match.
This also applies to I2C and SPI bus.
With this patch, the device' modalias will be shown as "acpi:INTABCD" as well.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
- Rephrase the comments about tx/rx_nbits validity checks,
- Remove the stale comment about SPI_3WIRE (the code it refers to was
removed in commit 368ca4e0c75612c0a4d6bbcef7efb944604340c2 ("spi:
Eliminate 3WIRE spi_transfer check")).
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Commit e13ac47bec20 (spi: Use stable dev_name for ACPI enumerated SPI
slaves) changed the SPI device naming to be based on ACPI device name
instead of carrying bus number and chip select for devices enumerated
from ACPI namespace.
In case of a buggy BIOS that lists multiple SPI devices sharing the same
chip select (even though they should use different) the current code fails
to detect that and allows the devices to be added to the bus.
Fix this by walking through the bus and comparing spi->chip_select instead
of device name. This should work regardless what the device name will be in
future.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
For slightly better readability.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
This corrects a problem in spi_pump_messages() that leads to an spi
message hanging forever when a call to transfer_one_message() fails.
This failure occurs in my MCP2210 driver when the cs_change bit is set
on the last transfer in a message, an operation which the hardware does
not support.
Rationale
Since the transfer_one_message() returns an int, we must presume that it
may fail. If transfer_one_message() should never fail, it should return
void. Thus, calls to transfer_one_message() should properly manage a
failure.
Fixes: ffbbdd21329f3 (spi: create a message queueing infrastructure)
Signed-off-by: Daniel Santos <daniel.santos@pobox.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
|
|
Use list_first_entry_or_null() to save a few lines.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Checking for SPI_3WIRE isn't needed. spi_setup() already prevents 3WIRE
mode from being combined with DUAL or QUAD mode support. So there is no
need to differentiate between a single bit device with SPI_3WIRE set and
one with without. It doesn't change the allowed bit widths.
Signed-off-by: Trent Piepho <tpiepho@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
|
|
Currently we do a bunch of per-message validation and initialisation in
__spi_async() which is called with the bus lock held. Since none of this
validation depends on the current bus status there's no need to hold the
lock to do it so split it out into a separate __spi_validate() function
which is called prior to taking the bus lock.
This could be slightly neater but keep things simple for now to show the
code motion clearly.
Based on observations from Martin Sperl.
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
devres_add() should be called when the action to be undone succeeded,
not when it failed. Fix the inverted test in devm_spi_register_master()
which was doing the opposite.
The user-visible issue without this fix is:
insmod spi-tegra114.ko
Assume there's an MTD device on that SPI bus, which creates /dev/mtd0.
rmmod spi-tegra114
Doesn't remove devices on the SPI bus.
insmod spi-tegra114.ko
Creates a duplicate SPI device which creates /dev/mtd1.
hexdump -C /dev/mtd0
That's the old device, which uses an SPI bus hosted by a non-existent
module, which causes the oops below.
Unable to handle kernel paging request at virtual address bf0017c0
pgd = c0004000
[bf0017c0] *pgd=ad51b811, *pte=00000000, *ppte=00000000
Internal error: Oops: 80000007 [#1] PREEMPT SMP ARM
...
PC is at 0xbf0017c0
LR is at spi_pump_messages+0x15c/0x204
pc : [<bf0017c0>] lr : [<c02f0af8>] psr: 60000113
...
Fixes: 666d5b4c742b ("spi: core: Add devm_spi_register_master()")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
- ACPI-based device hotplug fixes for issues introduced recently and a
fix for an older error code path bug in the ACPI PCI host bridge
driver
- Fix for recently broken OMAP cpufreq build from Viresh Kumar
- Fix for a recent hibernation regression related to s2disk
- Fix for a locking-related regression in the ACPI EC driver from
Puneet Kumar
- System suspend error code path fix related to runtime PM and runtime
PM documentation update from Ulf Hansson
- cpufreq's conservative governor fix from Xiaoguang Chen
- New processor IDs for intel_idle and turbostat and removal of an
obsolete Kconfig option from Len Brown
- New device IDs for the ACPI LPSS (Low-Power Subsystem) driver and
ACPI-based PCI hotplug (ACPIPHP) cleanup from Mika Westerberg
- Removal of several ACPI video DMI blacklist entries that are not
necessary any more from Aaron Lu
- Rework of the ACPI companion representation in struct device and code
cleanup related to that change from Rafael J Wysocki, Lan Tianyu and
Jarkko Nikula
- Fixes for assigning names to ACPI-enumerated I2C and SPI devices from
Jarkko Nikula
* tag 'pm+acpi-2-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (24 commits)
PCI / hotplug / ACPI: Drop unused acpiphp_debug declaration
ACPI / scan: Set flags.match_driver in acpi_bus_scan_fixed()
ACPI / PCI root: Clear driver_data before failing enumeration
ACPI / hotplug: Fix PCI host bridge hot removal
ACPI / hotplug: Fix acpi_bus_get_device() return value check
cpufreq: governor: Remove fossil comment in the cpufreq_governor_dbs()
ACPI / video: clean up DMI table for initial black screen problem
ACPI / EC: Ensure lock is acquired before accessing ec struct members
PM / Hibernate: Do not crash kernel in free_basic_memory_bitmaps()
ACPI / AC: Remove struct acpi_device pointer from struct acpi_ac
spi: Use stable dev_name for ACPI enumerated SPI slaves
i2c: Use stable dev_name for ACPI enumerated I2C slaves
ACPI: Provide acpi_dev_name accessor for struct acpi_device device name
ACPI / bind: Use (put|get)_device() on ACPI device objects too
ACPI: Eliminate the DEVICE_ACPI_HANDLE() macro
ACPI / driver core: Store an ACPI device pointer in struct acpi_dev_node
cpufreq: OMAP: Fix compilation error 'r & ret undeclared'
PM / Runtime: Fix error path for prepare
PM / Runtime: Update documentation around probe|remove|suspend
cpufreq: conservative: set requested_freq to policy max when it is over policy max
...
|
|
Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.
[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Current spi bus_num.chip_select "spix.y" based device naming scheme may not
be stable enough to be used in name based matching, for instance within
ALSA SoC subsystem.
This can be problem in PC kind of platforms if there are changes in SPI bus
configuration, amount of busses or probe order.
This patch addresses the problem by using the ACPI device name with
"spi-" prefix for ACPI enumerated SPI slave. For them device name
"spix.y" becomes "spi-INTABCD:ij".
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Modify struct acpi_dev_node to contain a pointer to struct acpi_device
associated with the given device object (that is, its ACPI companion
device) instead of an ACPI handle corresponding to it. Introduce two
new macros for manipulating that pointer in a CONFIG_ACPI-safe way,
ACPI_COMPANION() and ACPI_COMPANION_SET(), and rework the
ACPI_HANDLE() macro to take the above changes into account.
Drop the ACPI_HANDLE_SET() macro entirely and rework its users to
use ACPI_COMPANION_SET() instead. For some of them who used to
pass the result of acpi_get_child() directly to ACPI_HANDLE_SET()
introduce a helper routine acpi_preset_companion() doing an
equivalent thing.
The main motivation for doing this is that there are things
represented by struct acpi_device objects that don't have valid
ACPI handles (so called fixed ACPI hardware features, such as
power and sleep buttons) and we would like to create platform
device objects for them and "glue" them to their ACPI companions
in the usual way (which currently is impossible due to the
lack of valid ACPI handles). However, there are more reasons
why it may be useful.
First, struct acpi_device pointers allow of much better type checking
than void pointers which are ACPI handles, so it should be more
difficult to write buggy code using modified struct acpi_dev_node
and the new macros. Second, the change should help to reduce (over
time) the number of places in which the result of ACPI_HANDLE() is
passed to acpi_bus_get_device() in order to obtain a pointer to the
struct acpi_device associated with the given "physical" device,
because now that pointer is returned by ACPI_COMPANION() directly.
Finally, the change should make it easier to write generic code that
will build both for CONFIG_ACPI set and unset without adding explicit
compiler directives to it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com> # on Haswell
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com> # for ATA and SDIO part
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael J Wysocki:
- New power capping framework and the the Intel Running Average Power
Limit (RAPL) driver using it from Srinivas Pandruvada and Jacob Pan.
- Addition of the in-kernel switching feature to the arm_big_little
cpufreq driver from Viresh Kumar and Nicolas Pitre.
- cpufreq support for iMac G5 from Aaro Koskinen.
- Baytrail processors support for intel_pstate from Dirk Brandewie.
- cpufreq support for Midway/ECX-2000 from Mark Langsdorf.
- ARM vexpress/TC2 cpufreq support from Sudeep KarkadaNagesha.
- ACPI power management support for the I2C and SPI bus types from Mika
Westerberg and Lv Zheng.
- cpufreq core fixes and cleanups from Viresh Kumar, Srivatsa S Bhat,
Stratos Karafotis, Xiaoguang Chen, Lan Tianyu.
- cpufreq drivers updates (mostly fixes and cleanups) from Viresh
Kumar, Aaro Koskinen, Jungseok Lee, Sudeep KarkadaNagesha, Lukasz
Majewski, Manish Badarkhe, Hans-Christian Egtvedt, Evgeny Kapaev.
- intel_pstate updates from Dirk Brandewie and Adrian Huang.
- ACPICA update to version 20130927 includig fixes and cleanups and
some reduction of divergences between the ACPICA code in the kernel
and ACPICA upstream in order to improve the automatic ACPICA patch
generation process. From Bob Moore, Lv Zheng, Tomasz Nowicki, Naresh
Bhat, Bjorn Helgaas, David E Box.
- ACPI IPMI driver fixes and cleanups from Lv Zheng.
- ACPI hotplug fixes and cleanups from Bjorn Helgaas, Toshi Kani, Zhang
Yanfei, Rafael J Wysocki.
- Conversion of the ACPI AC driver to the platform bus type and
multiple driver fixes and cleanups related to ACPI from Zhang Rui.
- ACPI processor driver fixes and cleanups from Hanjun Guo, Jiang Liu,
Bartlomiej Zolnierkiewicz, Mathieu Rhéaume, Rafael J Wysocki.
- Fixes and cleanups and new blacklist entries related to the ACPI
video support from Aaron Lu, Felipe Contreras, Lennart Poettering,
Kirill Tkhai.
- cpuidle core cleanups from Viresh Kumar and Lorenzo Pieralisi.
- cpuidle drivers fixes and cleanups from Daniel Lezcano, Jingoo Han,
Bartlomiej Zolnierkiewicz, Prarit Bhargava.
- devfreq updates from Sachin Kamat, Dan Carpenter, Manish Badarkhe.
- Operation Performance Points (OPP) core updates from Nishanth Menon.
- Runtime power management core fix from Rafael J Wysocki and update
from Ulf Hansson.
- Hibernation fixes from Aaron Lu and Rafael J Wysocki.
- Device suspend/resume lockup detection mechanism from Benoit Goby.
- Removal of unused proc directories created for various ACPI drivers
from Lan Tianyu.
- ACPI LPSS driver fix and new device IDs for the ACPI platform scan
handler from Heikki Krogerus and Jarkko Nikula.
- New ACPI _OSI blacklist entry for Toshiba NB100 from Levente Kurusa.
- Assorted fixes and cleanups related to ACPI from Andy Shevchenko, Al
Stone, Bartlomiej Zolnierkiewicz, Colin Ian King, Dan Carpenter,
Felipe Contreras, Jianguo Wu, Lan Tianyu, Yinghai Lu, Mathias Krause,
Liu Chuansheng.
- Assorted PM fixes and cleanups from Andy Shevchenko, Thierry Reding,
Jean-Christophe Plagniol-Villard.
* tag 'pm+acpi-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (386 commits)
cpufreq: conservative: fix requested_freq reduction issue
ACPI / hotplug: Consolidate deferred execution of ACPI hotplug routines
PM / runtime: Use pm_runtime_put_sync() in __device_release_driver()
ACPI / event: remove unneeded NULL pointer check
Revert "ACPI / video: Ignore BIOS initial backlight value for HP 250 G1"
ACPI / video: Quirk initial backlight level 0
ACPI / video: Fix initial level validity test
intel_pstate: skip the driver if ACPI has power mgmt option
PM / hibernate: Avoid overflow in hibernate_preallocate_memory()
ACPI / hotplug: Do not execute "insert in progress" _OST
ACPI / hotplug: Carry out PCI root eject directly
ACPI / hotplug: Merge device hot-removal routines
ACPI / hotplug: Make acpi_bus_hot_remove_device() internal
ACPI / hotplug: Simplify device ejection routines
ACPI / hotplug: Fix handle_root_bridge_removal()
ACPI / hotplug: Refuse to hot-remove all objects with disabled hotplug
ACPI / scan: Start matching drivers after trying scan handlers
ACPI: Remove acpi_pci_slot_init() headers from internal.h
ACPI / blacklist: fix name of ThinkPad Edge E530
PowerCap: Fix build error with option -Werror=format-security
...
Conflicts:
arch/arm/mach-omap2/opp.c
drivers/Kconfig
drivers/spi/spi.c
|
|
|
|
|
|
|
|
Fix the following checkpatch error and warnings.
ERROR: space required after that ',' (ctx:VxV)
WARNING: quoted string split across lines
WARNING: max() should probably be max_t(int, nb, master->num_chipselect)
WARNING: sizeof *spi should be sizeof(*spi)
WARNING: sizeof *master should be sizeof(*master)
WARNING: sizeof x should be sizeof(x)
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
|
|
The loops which SPI controller drivers use to process the list of transfers
in a spi_message are typically very similar and have some error prone areas
such as the handling of /CS. Help simplify drivers by factoring this code
out into the core - if drivers provide a transfer_one() function instead
of a transfer_one_message() function the core will handle processing at the
message level.
/CS can be controlled by either setting cs_gpio or providing a set_cs
function. If this is not possible for hardware reasons then both can be
omitted and the driver should continue to implement manual /CS handling.
This is a first step in refactoring and it is expected that there will be
further enhancements, for example factoring out of the mapping of transfers
for DMA and the initiation and completion of interrupt driven transfers.
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Many SPI drivers perform setup and tear down on every message, usually
doing things like DMA mapping the message. Provide hooks for them to use
to provide such operations.
This is of limited value for drivers that implement transfer_one_message()
but will be of much greater utility with future factoring out of standard
implementations of that function.
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
If the SPI device is enumerated from ACPI namespace (it has an ACPI handle)
it might have ACPI methods that needs to be called in order to transition
the device to different power states (such as _PSx).
We follow what has been done for platform and I2C buses here and attach the
SPI device to the ACPI power domain if the device has an ACPI handle. This
makes sure that the device is powered on when its ->probe() is called.
For non-ACPI devices this patch is a no-op.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
There is a minor fault about ACPI enumerated SPI devices with their modalias
attribute. Now modalias is set by device instance not by hardware ID.
For example "spi:INTABCD:00", "spi:INTABCD:01" etc.
This means each device instance gets different modalias which does match
with generated modules.alias. Currently this is not problem as matching can
happen also with "acpi:INTABCD" modalias.
Fix this by using ACPI hardware ID.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The dev_attrs field of struct bus_type is going away soon, dev_groups
should be used instead. This converts the spi bus code to use the
correct field.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Provide tracepoints for the lifecycle of a message from submission to
completion and for the active time for masters to help with performance
analysis of SPI I/O.
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Instead of getting the raw property, checking the length, and doing
endian conversion each time, use the OF function
of_property_read_u32() that does all that.
Error messages are slightly improved with error codes from
of_property_read_u32() for different ways the property may be invalid
(missing, too short, etc.)
Signed-off-by: Trent Piepho <tpiepho@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
request_module() can handle format strings on its own, no need to create
the full module name ourself.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Help simplify the cleanup code for SPI master drivers by providing a
managed master registration function, ensuring that the master is
automatically unregistered whenever the device is unbound.
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
|
|
|
|
|
|
|
|
spi: quad: fix the name of DT property in patch
The previous property name spi-tx-nbits and spi-rx-nbits looks not
human-readable. To make it consistent with other devices, using property
name spi-tx-bus-width and spi-rx-bus-width instead of the previous one
specify the number of data wires that spi controller will work in.
Add the specification in spi-bus.txt.
Signed-off-by: wangyuhang <wangyuhang2014@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
In the case spi_master_initialize_queue() fails, current code calls
device_unregister() before return error from spi_register_master().
However, all the drivers call spi_master_put() in the error path if
spi_register_master() fails. Thus we should call device_del() rather than
device_unregister() before return error from spi_register_master().
This also makes all the spi_register_master() error handling consistent,
because all other error paths of spi_register_master() expect drivers to
call spi_master_put() if spi_register_master() fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The addition SPI quad support made the DT properties mandatory, breaking
compatibility with existing systems. Fix that by making them optional,
also improving the error messages while we're at it.
Signed-off-by: Mark Brown <broonie@linaro.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
|
|
Delete a "return" when commit the patch to a new kernel version
by mistake. So recover it.
Signed-off-by: wangyuhang <wangyuhang2014@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
|
|
We have tested master->running immediately after grab the master->queue_lock.
The status of master->running won't be changed until we release the lock.
Thus remove a redundant test for master->running.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
There is a bug in the following patch:
http://comments.gmane.org/gmane.linux.kernel.spi.devel/14420
spi: DUAL and QUAD support
fix the previous patch some mistake below:
1. DT in slave node, use "spi-tx-nbits = <1/2/4>" in place of using
"spi-tx-dual, spi-tx-quad" directly, same to rx. So correct the
previous way to get the property in @of_register_spi_devices().
2. Change the value of transfer bit macro(SPI_NBITS_SINGLE, SPI_NBITS_DUAL
SPI_NBITS_QUAD) to 0x01, 0x02 and 0x04 to match the actual wires.
3. Add the following check
(1)keep the tx_nbits and rx_nbits in spi_transfer is not beyond the
single, dual and quad.
(2)keep tx_nbits and rx_nbits are contained by @spi_device->mode
example: if @spi_device->mode = DUAL, then tx/rx_nbits can not be set
to QUAD(SPI_NBITS_QUAD)
(3)if "@spi_device->mode & SPI_3WIRE", then tx/rx_nbits should be in
single(SPI_NBITS_SINGLE)
Checking of the tx/rx transfer bits and mode bits should be done conditionally
based on type of buffer filled else EINVAL condition will
always get hit either for rx or tx.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
fix the previous patch some mistake below:
1. DT in slave node, use "spi-tx-nbits = <1/2/4>" in place of using
"spi-tx-dual, spi-tx-quad" directly, same to rx. So correct the
previous way to get the property in @of_register_spi_devices().
2. Change the value of transfer bit macro(SPI_NBITS_SINGLE, SPI_NBITS_DUAL
SPI_NBITS_QUAD) to 0x01, 0x02 and 0x04 to match the actual wires.
3. Add the following check
(1)keep the tx_nbits and rx_nbits in spi_transfer is not beyond the
single, dual and quad.
(2)keep tx_nbits and rx_nbits are contained by @spi_device->mode
example: if @spi_device->mode = DUAL, then tx/rx_nbits can not be set
to QUAD(SPI_NBITS_QUAD)
(3)if "@spi_device->mode & SPI_3WIRE", then tx/rx_nbits should be in
single(SPI_NBITS_SINGLE)
Signed-off-by: wangyuhang <wangyuhang2014@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Since the 'spi: Support transfer speed checking in the core'
change, the SPI core validates the desired speed of a given
transfer against the minimum and maximum speeds supported by
the controller.
If the speed of a transfer is not specified, the core uses
the maximum speed of the actual SPI device. However if the
maximum speed of the actual device is greater than the
maximum speed of the controller, the core will reject the
transfer due to the aforementioned change.
Change the code to use the maximum speed of the controller
by default if that is below the device's maximum speed.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Most SPI drivers that implement runtime PM support use identical code to
do so: they acquire a runtime PM lock in prepare_transfer_hardware() and
then they release it in unprepare_transfer_hardware(). The variations in
this are mostly missing error checking and the choice to use autosuspend.
Since these runtime PM calls are normally the only thing in the prepare
and unprepare callbacks and the autosuspend API transparently does the
right thing on devices with autosuspend disabled factor all of this out
into the core with a flag to enable the behaviour.
Signed-off-by: Mark Brown <broonie@linaro.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
