| Age | Commit message (Collapse) | Author |
|---|
|
Currently, pch_spi_start_transfer failure is not anticipated.
This patch adds the processing.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
This patch supports a spi mode setup and bit order setup by IO control.
spi mode: mode 0 to mode 3
bit order: LSB first, MSB first
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Currently, when spi-topcliff-pch receives transmit request over 4KByte,
this driver can't process correctly. This driver needs to divide the data
into 4Kbyte unit.
This patch fixes the issue.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Simplify the error handling by moving the code to free gpios in one place.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Convert static struct pci_device_id *[] to static DEFINE_PCI_DEVICE_TABLE
tables.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
This patch adds support for the SPI controller found on the Broadcom BCM63xx
SoCs.
Signed-off-by: Tanguy Bouzeloc <tanguy.bouzeloc@efixo.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
CSR SiRFprimaII has two SPIs (SPI0 and SPI1). Features:
* Master and slave modes
* 8-/12-/16-/32-bit data unit
* 256 bytes receive data FIFO and 256 bytes transmit data FIFO
* Multi-unit frame
* Configurable SPI_EN (chip select pin) active state
* Configurable SPI_CLK polarity
* Configurable SPI_CLK phase
* Configurable MSB/LSB first
Signed-off-by: Zhiwu Song <zhiwu.song@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Fix for:
drivers/spi/spi-topcliff-pch.c: In function ‘pch_spi_handler_sub’:
drivers/spi/spi-topcliff-pch.c:325:17: warning: ‘bpw_len’ may be
used uninitialized in this function [-Wuninitialized]
drivers/spi/spi-topcliff-pch.c:325:42: warning: ‘rx_index’ may be
used uninitialized in this function [-Wuninitialized]
drivers/spi/spi-topcliff-pch.c:325:42: warning: ‘tx_index’ may be
used uninitialized in this function [-Wuninitialized]
Move usage of tx_index, rx_index and bpw_len into the same
block as where they are set to prevent uninitialized usage.
v2: instead of init variables with 0 move the whole block
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Some systems have SPI devices located on plugin modules which are
enumerated at runtime as devices. The drivers for these plugin modules
need to register their SPI devices at probe() time so want to be able
to call spi_register_board_info() but that function is currently marked
as __init rather than __devinit so this usage isn't legal. Change the
annotation to __devinit to handle this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Convert the s3c64xx driver to using the new message queue factored out of
the pl022 driver by Linus Walleij, saving us a nice block of code and
getting the benefits of improvements implemented in the core.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
They are all defined in an if SPI_MASTER ... endif block.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
This patch adds SuperH HSPI driver.
It is still prototype driver, but has enough function at this point.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/cleanup
* 'next/cleanup-s3c24xx' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (24 commits)
ARM: S3C24XX: remove call to s3c24xx_setup_clocks
ARM: S3C24XX: add get_rate for clk_p on S3C2416/2443
ARM: S3C24XX: add get_rate for clk_h on S3C2416/2443
ARM: S3C24XX: remove XXX_setup_clocks method from S3C2443
ARM: S3C24XX: remove obsolete S3C2416_DMA option
ARM: S3C24XX: Reuse S3C2443 dma for S3C2416
ARM: S3C24XX: Fix indentation of dma-s3c2443
ARM: S3C24XX: Move device setup files to mach directory
ARM: S3C24XX: Consolidate Simtec extensions
ARM: S3C24XX: move simtec-specific code to mach directory
ARM: S3C24XX: Move common-smdk code to mach directory
ARM: S3C24XX: Move s3c2443-clock.c to mach-s3c24xx
ARM: s3c2410_defconfig: update s3c2410_defconfig
ARM: S3C2443: move mach-s3c2443/* into mach-s3c24xx/
ARM: S3C2440: move mach-s3c2440/* into mach-s3c24xx/
ARM: S3C2416: move mach-s3c2416/* into mach-s3c24xx/
ARM: S3C2412: move mach-s3c2412/* into mach-s3c24xx/
ARM: S3C2410: move mach-s3c2410/* into mach-s3c24xx/
ARM: S3C24XX: change the ARCH_S3C2410 to ARCH_S3C24XX
ARM: S3C2410: move s3c2410_baseclk_add to clock.h
...
|
|
This rips the message queue in the PL022 driver out and pushes
it into (optional) common infrastructure. Drivers that want to
use the message pumping thread will need to define the new
per-messags transfer methods and leave the deprecated transfer()
method as NULL.
Most of the design is described in the documentation changes that
are included in this patch.
Since there is a queue that need to be stopped when the system
is suspending/resuming, two new calls are implemented for the
device drivers to call in their suspend()/resume() functions:
spi_master_suspend() and spi_master_resume().
ChangeLog v1->v2:
- Remove Kconfig entry and do not make the queue support optional
at all, instead be more agressive and have it as part of the
compulsory infrastructure.
- If the .transfer() method is implemented, delete print a small
deprecation notice and do not start the transfer pump.
- Fix a bitrotted comment.
ChangeLog v2->v3:
- Fix up a problematic sequence courtesy of Chris Blair.
- Stop rather than destroy the queue on suspend() courtesy of
Chris Blair.
Signed-off-by: Chris Blair <chris.blair@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
The SH7757 has RSPI module. This patch supports it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
This SPI controller's access size is 32, or 8-bit. The previous driver
supported 32-bit only. So, this patch adds IORESOURCE_MEM_TYPE_MASK
decoding, an then, the driver can handle the SPI controller of 8-bit.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
This patch changes the ARCH name to "ARCH_S3C24XX" for Samsung
S3C2410, S3C2412, S3C2413, S3C2416, S3C2440, S3C2442, S3C2443,
and S3C2450 SoCs so that we can merge the mach-xxx directories
and plat-s3c24xx dir. to just one mach-s3c24xx for them.
I think this should be sent to upstream via samsung tree because
this touches many samsung stuff.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
[for the gadget part:]
Acked-by: Felipe Balbi <balbi@ti.com>
[for the framebuffer (video) part:]
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
[For the watchdog-part:]
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
.device_fc is added in struct dma_slave_config recently. All user drivers, which
want DMA to be the flow controller must pass this field as false. As earlier
driver don't look to use this feature, mark it false for now.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
Add device tree support to the OMAP2+ McSPI driver.
Add the bindings documentation.
Based on original code from Rajendra.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
WARNING: drivers/spi/built-in.o(.devinit.text+0xdb8): Section mismatch in reference from the function pl022_probe() to the function .init.text:pl022_dma_probe()
The function __devinit pl022_probe() references
a function __init pl022_dma_probe().
If pl022_dma_probe is only used by pl022_probe then
annotate pl022_dma_probe with a matching annotation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Rename static struct pci_driver pch_spi_pcidev to
pch_spi_pcidev_driver to get rid of warnings from modpost checks.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
The spi-s3c64xx driver is also used on Exynos4 so update the dependency
to enable build on those platforms.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[grant.likely: relax depends to ARCH_EXYNOS instead of ARCH_EXYNOS4]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
This switches the PL022 worker to a kthread in order to get
hold of a mechanism to control the message pump priority. On
low-latency systems elevating the message kthread to realtime
priority give a real sleek response curve. This has been
confirmed by measurements. Realtime priority elevation for
a certain PL022 port can be requested from platform data.
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Chris Blair <chris.blair@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
The memory allocated using kzalloc by spi_alloc_master so it doesn't
need to be set to 0 again.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
spi.h now only contains the definition of the platform data structure
for the driver in spi-s3c24xx.c . Therefore it does not need to stay
in include/mach but can instead live in linux/spi/s3c24xx.h .
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc
Conflicts:
drivers/spi/spi-s3c64xx.c
|
|
Enable and disable the clocks to the SPI controller using runtime PM. This
serves the dual purpose of reducing power consumption a little and letting
the core know when the device is idle.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
|
|
In preparation for the addition of runtime PM ops.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Although the hardware supports interrupts we're not currently using them
at all since for small transfers the overhead is greater than that for
busy waiting and for large transfers we have interrupts from the DMA.
This means that if the hardware reports an error (especially one which
might not stall transfer) we might miss it.
Take a first pass at dealing with such errors by enabling the interrupt
if we can and logging the errors if they happen. Ideally we'd report the
error via the affected transfer but since we're in master mode it's very
difficult to trigger errors at present and this code is much simpler.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (53 commits)
ARM: mach-shmobile: specify CHCLR registers on SH7372
dma: shdma: fix runtime PM: clear channel buffers on reset
dma/imx-sdma: save irq flags when use spin_lock in sdma_tx_submit
dmaengine/ste_dma40: clear LNK on channel startup
dmaengine: intel_mid_dma: remove legacy pm interface
ASoC: mxs: correct 'direction' of device_prep_dma_cyclic
dmaengine: intel_mid_dma: error path fix
dmaengine: intel_mid_dma: locking and freeing fixes
mtd: gpmi-nand: move to dma_transfer_direction
mtd: fix compile error for gpmi-nand
mmc: mxs-mmc: fix the dma_transfer_direction migration
dmaengine: add DMA_TRANS_NONE to dma_transfer_direction
dma: mxs-dma: Don't use CLKGATE bits in CTRL0 to disable DMA channels
dma: mxs-dma: make mxs_dma_prep_slave_sg() multi user safe
dma: mxs-dma: Always leave mxs_dma_init() with the clock disabled.
dma: mxs-dma: fix a typo in comment
DMA: PL330: Remove pm_runtime_xxx calls from pl330 probe/remove
video i.MX IPU: Fix display connections
i.MX IPU DMA: Fix wrong burstsize settings
dmaengine/ste_dma40: allow fixed physical channel
...
Fix up conflicts in drivers/dma/{Kconfig,mxs-dma.c,pl330.c}
The conflicts looked pretty trivial, but I'll ask people to verify them.
|
|
git://git.secretlab.ca/git/linux-2.6
2nd set of device tree changes and SPI bug fixes for v3.3
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux-2.6:
of/irq: Add interrupts-names property to name an irq resource
of/address: Add reg-names property to name an iomem resource
* tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6:
spi/tegra: depend instead of select TEGRA_SYSTEM_DMA
|
|
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (119 commits)
MIPS: Delete unused function add_temporary_entry.
MIPS: Set default pci cache line size.
MIPS: Flush huge TLB
MIPS: Octeon: Remove SYS_SUPPORTS_HIGHMEM.
MIPS: Octeon: Add support for OCTEON II PCIe
MIPS: Octeon: Update PCI Latency timer and enable more error reporting.
MIPS: Alchemy: Update cpu-feature-overrides
MIPS: Alchemy: db1200: Improve PB1200 detection.
MIPS: Alchemy: merge Au1000 and Au1300-style IRQ controller code.
MIPS: Alchemy: chain IRQ controllers to MIPS IRQ controller
MIPS: Alchemy: irq: register pm at irq init time
MIPS: Alchemy: Touchscreen support on DB1100
MIPS: Alchemy: Hook up IrDA on DB1000/DB1100
net/irda: convert au1k_ir to platform driver.
MIPS: Alchemy: remove unused board headers
MTD: nand: make au1550nd.c a platform_driver
MIPS: Netlogic: Mark Netlogic chips as SMT capable
MIPS: Netlogic: Add support for XLP 3XX cores
MIPS: Netlogic: Merge some of XLR/XLP wakup code
MIPS: Netlogic: Add default XLP config.
...
Fix up trivial conflicts in arch/mips/kernel/{perf_event_mipsxx.c,
traps.c} and drivers/tty/serial/Makefile
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Cleanups for the Samsung platforms
Various cleanup changes that the device driver changes are built upon.
Since the samsung cleanups depend on the device tree series, which
depends on the first set of cleanups for tegra.
* tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: EXYNOS: Use gpio_request_one
ARM: S5PV210: Use gpio_request_one
ARM: S3C64XX: Modified according to SPI consolidation work
ARM: S5PV210: Modified files for SPI consolidation work
ARM: S5P64X0: Modified files for SPI consolidation work
ARM: S5PC100: Modified files for SPI consolidation work
ARM: S3C64XX: Modified files for SPI consolidation work
ARM: SAMSUNG: Consolidation of SPI platform devices to plat-samsung
ARM: SAMSUNG: Remove SPI bus clocks from platform data
ARM: S5PV210: Add SPI clkdev support
ARM: S5P64X0: Add SPI clkdev support
ARM: S5PC100: Add SPI clkdev support
ARM: S3C64XX: Add SPI clkdev support
spi/s3c64xx: Use bus clocks created using clkdev
mmc: sdhci-s3c: Use generic clock names for sdhci bus clock options
ARM: SAMSUNG: Add lookup of sdhci-s3c clocks using generic names
ARM: SAMSUNG: Remove SDHCI bus clocks from platform data
ARM: SAMSUNG: Use kmemdup rather than duplicating its implementation
ARM: EXYNOS: remove exynos4_scu_enable()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (53 commits)
Kconfig: acpi: Fix typo in comment.
misc latin1 to utf8 conversions
devres: Fix a typo in devm_kfree comment
btrfs: free-space-cache.c: remove extra semicolon.
fat: Spelling s/obsolate/obsolete/g
SCSI, pmcraid: Fix spelling error in a pmcraid_err() call
tools/power turbostat: update fields in manpage
mac80211: drop spelling fix
types.h: fix comment spelling for 'architectures'
typo fixes: aera -> area, exntension -> extension
devices.txt: Fix typo of 'VMware'.
sis900: Fix enum typo 'sis900_rx_bufer_status'
decompress_bunzip2: remove invalid vi modeline
treewide: Fix comment and string typo 'bufer'
hyper-v: Update MAINTAINERS
treewide: Fix typos in various parts of the kernel, and fix some comments.
clockevents: drop unknown Kconfig symbol GENERIC_CLOCKEVENTS_MIGR
gpio: Kconfig: drop unknown symbol 'CS5535_GPIO'
leds: Kconfig: Fix typo 'D2NET_V2'
sound: Kconfig: drop unknown symbol ARCH_CLPS7500
...
Fix up trivial conflicts in arch/powerpc/platforms/40x/Kconfig (some new
kconfig additions, close to removed commented-out old ones)
|
|
spi changes queued up for v3.3 merge window
* tag 'spi-for-linus-20120104' of git://git.secretlab.ca/git/linux-2.6:
spi: Fix device unregistration when unregistering the bus master
spi-topcliff-pch: Change company name OKI SEMICONDUCTOR to LAPIS Semiconductor
spi-topcliff-pch: Support new device LAPIS Semiconductor ML7831 IOH
spi/omap: Correct the error path
spi/omap: call pm_runtime_disable in error path and remove
spi/omap: Use a workqueue per omap2_mcspi controller
|
|
Changes queued in gpio/next for the start of the 3.3 merge window
* tag 'gpio-for-linus-20120104' of git://git.secretlab.ca/git/linux-2.6:
gpio: Add decode of WM8994 GPIO configuration
gpio: Convert GPIO drivers to module_platform_driver
gpio: Fix typo in comment in Samsung driver
gpio: Explicitly index samsung_gpio_cfgs
gpio: Add Linus Walleij as gpio co-maintainer
of: Add device tree selftests
of: create of_phandle_args to simplify return of phandle parsing data
gpio/powerpc: Eliminate duplication of of_get_named_gpio_flags()
gpio/microblaze: Eliminate duplication of of_get_named_gpio_flags()
gpiolib: output basic details and consolidate gpio device drivers
pch_gpio: Change company name OKI SEMICONDUCTOR to LAPIS Semiconductor
pch_gpio: Support new device LAPIS Semiconductor ML7831 IOH
spi/pl022: make the chip deselect handling thread safe
spi/pl022: add support for pm_runtime autosuspend
spi/pl022: disable the PL022 block when unused
spi/pl022: move device disable to workqueue thread
spi/pl022: skip default configuration before suspending
spi/pl022: fix build warnings
spi/pl022: only enable RX interrupts when TX is complete
|
|
git://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm
* 'amba-modalias' of git://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
sound: aaci: Enable module alias autogeneration for AMBA drivers
watchdog: sp805: Enable module alias autogeneration for AMBA drivers
fbdev: amba: Enable module alias autogeneration for AMBA drivers
serial: pl011: Enable module alias autogeneration for AMBA drivers
serial: pl010: Enable module alias autogeneration for AMBA drivers
spi: pl022: Enable module alias autogeneration for AMBA drivers
rtc: pl031: Enable module alias autogeneration for AMBA drivers
rtc: pl030: Enable module alias autogeneration for AMBA drivers
mmc: mmci: Enable module alias autogeneration for AMBA drivers
input: ambakmi: Enable module alias autogeneration for AMBA drivers
gpio: pl061: Enable module alias autogeneration for AMBA drivers
dmaengine: pl330: Enable module alias autogeneration for AMBA drivers
dmaengine: pl08x: Enable module alias autogeneration for AMBA drivers
hwrng: nomadik: Enable module alias autogeneration for AMBA drivers
ARM: amba: Auto-generate AMBA driver module aliases during modpost
ARM: amba: Move definition of struct amba_id to mod_devicetable.h
|
|
|
|
It's unlikely that anyone ever wants to turn off SYSTEM_DMA, but just in
case, it makes more sense to have the driver depend on it than select it.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
This patch modifies the driver to stop depending on the
clock names being passed from platform and switch over
to lookup clocks generic names using clkdev
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Device are added as children of the bus master's parent device, but
spi_unregister_master() looks for devices to unregister in the bus
master's children. This results in the child devices not being
unregistered.
Fix this by registering devices as direct children of the bus master.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into gpio/next
|
|
Add basic support for the Au1300 variant(s):
- New GPIO/Interrupt controller
- DBDMA ids
- USB setup
- MMC support
- enable various PSC drivers
- detection code.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2866/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Fixes:
The function __devinit spi_gpio_probe() references
a function __init spi_gpio_alloc.isra.4().
If spi_gpio_alloc.isra.4 is only used by spi_gpio_probe then
annotate spi_gpio_alloc.isra.4 with a matching annotation.
[wsa: fix spi_gpio_request(), too]
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
|
|
When spi_fsl_espi is chosen to be built as a module, there is a build
error because we test only CONFIG_SPI_FSL_ESPI in declaration of
struct mpc8xxx_spi in drivers/spi/spi_fsl_lib.h. Also some called
functions are not exported.
So we forbid CONFIG_SPI_FSL_ESPI to be tristate here.
The error looks like:
drivers/spi/spi_fsl_espi.c: In function 'fsl_espi_bufs':
drivers/spi/spi_fsl_espi.c:232: error: 'struct mpc8xxx_spi' has no member named 'len'
...
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
|
|
Include linux/module.h to fix below build error:
CC drivers/spi/spi-nuc900.o
drivers/spi/spi-nuc900.c:484: error: 'THIS_MODULE' undeclared here (not in a function)
drivers/spi/spi-nuc900.c:489: error: expected declaration specifiers or '...' before string constant
drivers/spi/spi-nuc900.c:489: warning: data definition has no type or storage class
drivers/spi/spi-nuc900.c:489: warning: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
drivers/spi/spi-nuc900.c:489: warning: function declaration isn't a prototype
drivers/spi/spi-nuc900.c:490: error: expected declaration specifiers or '...' before string constant
drivers/spi/spi-nuc900.c:490: warning: data definition has no type or storage class
drivers/spi/spi-nuc900.c:490: warning: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
drivers/spi/spi-nuc900.c:490: warning: function declaration isn't a prototype
drivers/spi/spi-nuc900.c:491: error: expected declaration specifiers or '...' before string constant
drivers/spi/spi-nuc900.c:491: warning: data definition has no type or storage class
drivers/spi/spi-nuc900.c:491: warning: type defaults to 'int' in declaration of 'MODULE_LICENSE'
drivers/spi/spi-nuc900.c:491: warning: function declaration isn't a prototype
drivers/spi/spi-nuc900.c:492: error: expected declaration specifiers or '...' before string constant
drivers/spi/spi-nuc900.c:492: warning: data definition has no type or storage class
drivers/spi/spi-nuc900.c:492: warning: type defaults to 'int' in declaration of 'MODULE_ALIAS'
drivers/spi/spi-nuc900.c:492: warning: function declaration isn't a prototype
make[2]: *** [drivers/spi/spi-nuc900.o] Error 1
make[1]: *** [drivers/spi] Error 2
make: *** [drivers] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
|
|
Whithout including 'linux/module.h' spi-ath79 driver fails to compile
with the these errors:
drivers/spi/spi-ath79.c:273:12: error: 'THIS_MODULE' undeclared here (not in a function)
drivers/spi/spi-ath79.c:278:20: error: expected declaration specifiers or '...' before string constant
drivers/spi/spi-ath79.c:278:1: warning: data definition has no type or storage class
drivers/spi/spi-ath79.c:278:1: warning: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
drivers/spi/spi-ath79.c:278:20: warning: function declaration isn't a prototype
drivers/spi/spi-ath79.c:279:15: error: expected declaration specifiers or '...' before string constant
drivers/spi/spi-ath79.c:279:1: warning: data definition has no type or storage class
drivers/spi/spi-ath79.c:279:1: warning: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
drivers/spi/spi-ath79.c:279:15: warning: function declaration isn't a prototype
drivers/spi/spi-ath79.c:280:16: error: expected declaration specifiers or '...' before string constant
drivers/spi/spi-ath79.c:280:1: warning: data definition has no type or storage class
drivers/spi/spi-ath79.c:280:1: warning: type defaults to 'int' in declaration of 'MODULE_LICENSE'
drivers/spi/spi-ath79.c:280:16: warning: function declaration isn't a prototype
drivers/spi/spi-ath79.c:281:14: error: expected declaration specifiers or '...' before string constant
drivers/spi/spi-ath79.c:281:1: warning: data definition has no type or storage class
drivers/spi/spi-ath79.c:281:1: warning: type defaults to 'int' in declaration of 'MODULE_ALIAS'
drivers/spi/spi-ath79.c:281:14: warning: function declaration isn't a prototype
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
|
|
There is a possibility that the pump_message and giveback
run in parallel on a SMP system. Both the pump_message and
giveback threads work on the same SPI message queue.
Results will be in correct if the pump_message gets to
work on the queue first.
when the pump_message works with the queue, it reads the
head of the queue and removes it from the queue. pump_message
activates the chip select depending on this message read.
This leads to giveback working on the modified queue or a
emptied queue. If the queue is empty or if the next message on
the queue (which is not the actual next message, as the pump
message has removed the next message from the queue) is not for
the same SPI device as that Of the previous one, giveback will
de-activate the chip select activated by pump_message(),
which is wrong.
To solve this problem pump_message is made not to run and
access the queue until the giveback is done handling the queue.
I.e. by making the cur_msg NULL after the giveback has read the
queue.
Also a state variable has been introduced to keep track of when
the CS for next message is already activated and avoid to
double-activate it.
Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
