summaryrefslogtreecommitdiffstats
path: root/drivers/spi
AgeCommit message (Collapse)Author
2014-03-27spi: clps711x: Convert to use master->max_speed_hzAxel Lin
Set highest transfer speed to master->max_speed_hz and then we can remove hw->max_speed. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-27spi: clps711x: Enable driver compilation with COMPILE_TESTAxel Lin
This helps increasing build testing coverage. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-26MIPS: Alchemy: Unify Devboard support.Manuel Lauss
This patch merges support for all DB1xxx and PB1xxx boards into a single image, along with a new single defconfig for them. Run-tested on DB1300 and DB1500. Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com> Cc: Linux-MIPS <linux-mips@linux-mips.org> Patchwork: https://patchwork.linux-mips.org/patch/6577/ Patchwork: https://patchwork.linux-mips.org/patch/6659/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2014-03-26spi: omap-uwire: Remove full duplex checkAxel Lin
This driver sets the SPI_MASTER_HALF_DUPLEX flag, so the spi core will check transfers to ensure they are not full duplex. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-25spi: Do not require a completionMark Brown
There is no real reason why we require transfers to have a completion and the only user of the completion now checks to see if one has been provided before using it so stop enforcing this. This makes it more convenient for drivers to chain multiple asynchronous transfers together. Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-25spi: topcliff-pch: Transform noisy message to dev_vdbgAlexander Stein
If during a SPI transfer with len larger than PCH_MAX_FIFO_DEPTH and the IRQ handler happens to be called when the transmit FIFO is already empty, and SPSR_FI_BIT is set consequently, the message "spi_master spi32766: pch_spi_handler_sub : Transfer is not completed" is spammed to the systemlog, because tx_index has already increased further due to the next bytes to be written. This case is uncritical as new bytes have already been written. Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-25spi: coldfire-qspi: Simplify the code to set register bits for transfer speedAxel Lin
spi core will use spi->max_speed_hz as transfer speed if the transfer speed was not set. So we don't need to test t->speed_hz in mcfqspi_transfer_one(). Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-25spi: bcm63xx: Remove unused define for PFXAxel Lin
Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-25spi: efm32: use $vendor,$device scheme for compatible stringUwe Kleine-König
Wolfram Sang pointed out that "efm32,$device" is non-standard. So use the common scheme and prefix device with "efm32-". The old compatible string is left in place until arch/arm/boot/dts/efm32* is fixed. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Mark Brown <broonie@linaro.org> Cc: stable@vger.kernel.org
2014-03-25spi: clps711x: Remove <mach/hardware.h> dependencyAlexander Shiyan
This patch removes <mach/hardware.h> dependency. This is performed by replace hard coded used memory regions and interrupt to getting these values from resources passed to the driver. For the system-wide registers we now able to use SYSCON driver. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-24spi: topcliff-pch: Properly unregister platform devices on probe() error pathsAxel Lin
Ensure all registered platform devices are unregistered on probe() error paths. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-21spi: fsl-espi: Remove unused bits_per_word variable in fsl_espi_bufsAxel Lin
Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-21spi: altera: Remove the code to get unused platform_dataAxel Lin
The definition of struct altera_spi_platform_data does not exist in current tree. So remove the code to get platform_data which is never used. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-21spi: fsl-lib: Fix memory leak of pinfoAxel Lin
of_mpc8xxx_spi_probe() allocates memory for pinfo but the memory is not freed anywhere. of_mpc8xxx_spi_probe() is called in .probe() and pinfo should be freed in .remove(), so convert kzalloc to devm_kzalloc to fix the memory leak. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-21spi: xtensa-xtfpga: Enable driver compilation with COMPILE_TESTAxel Lin
This helps increasing build testing coverage. Signed-off-by: Axel Lin <axel.lin@ingics.com> Reviewed-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-21spi: nuc900: Fix setting multiple bits settings in registerAxel Lin
The correct way to set multiple bits settings is always clear these bit fields before set new settings. Current code does not cause problem because the reset value of these bit fields are 0, and these settings only set once during probe. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-21spi: atmel: fix printk format warningsRandy Dunlap
Fix printk format warning by using %p extension 'ad' for dma_addr_t. drivers/spi/spi-atmel.c:1228:3: warning: format '%x' expects argument of type 'unsigned int', but argument 7 has type 'dma_addr_t' [-Wformat] drivers/spi/spi-atmel.c:1228:3: warning: format '%x' expects argument of type 'unsigned int', but argument 9 has type 'dma_addr_t' [-Wformat] Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-18spi: remove obsolete spi-ti-ssp driverArnd Bergmann
The tnetv107x platform is getting removed, so this driver will not be needed any more. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Sekhar Nori <nsekhar@ti.com> Acked-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-17spi: core: Use master->max_speed_hz as transfer speed when xfer->speed_hz > ↵Axel Lin
master->max_speed_hz When xfer->speed_hz is greater than master->max_speed_hz, it's generally safe to use master->max_speed_hz as transfer speed. Thus use master->max_speed_hz as transfer speed rather than return error when xfer->speed_hz > master->max_speed_hz. Signed-off-by: Axel Lin <axel.lin@ingics.com> Tested-by: Guenter Roeck <linux@roeck-us.net> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-14spi: efm32: properly namespace location propertyUwe Kleine-König
While reviewing an i2c driver for efm32 that needs a similar property Wolfram Sang pointed out that "location" is a too generic name for something that is efm32 specific. So add an appropriate namespace and fall back to the generic name in case of failure. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-13spi: sh-sci: Prevent NULL pointer dereferenceAxel Lin
If sp->info is NULL, we will hit NULL pointer dereference in probe() while setting bus_num and num_chipselect for master: sp->bitbang.master->bus_num = sp->info->bus_num; sp->bitbang.master->num_chipselect = sp->info->num_chipselect; Thus add NULL test for sp->info in probe() to prevent NULL pointer dereference. Signed-off-by: Axel Lin <axel.lin@ingics.com> Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-13spi: sirf: Add missing spi_master_{resume,suspend} calls to PM callbacksAxel Lin
This is required since commit 2025172e3280 "spi/bitbang: Use core message pump". spi-bitbang now uses core message pump, so it needs to call spi_master_suspend/ spi_master_resume to stop/start the queue while suspend/resume. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-13spi: altera: Use bits_per_word_maskAxel Lin
This driver does not work for bits_per_word greater than 16. Set bits_per_word_mask so spi core will reject transfers that attempt to use an unsupported bits_per_word value. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-13spi: oc-tiny: Remove unneeded NULL checking for hw->bitbang.masterAxel Lin
We already has NULL test for master after calling spi_alloc_master(). Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-13spi: clps711x: Remove duplicate code to set default bits_per_word and max speedAxel Lin
In the implementation of __spi_validate(), spi core will set transfer bits_per_word and max speed as spi device default if it is not set for this transfer. So we can remove the same logic in spi_clps711x_setup_xfer() and spi_clps711x_transfer_one(). Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-13spi: sc18is602: Convert to let spi core validate transfer speedAxel Lin
Set master->max_speed_hz and master->min_speed_hz then spi core will handle checking transfer speed. So we can remove the same checking in this driver. This patch also remove testing if hz is 0 because spi->max_speed_hz will be default set to master->min_speed_hz if it was not set. So the transfer speed will never set to 0. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-13spi: add xtfpga SPI controller driverMax Filippov
This simple SPI master controller is built into xtfpga bitstreams. It always transfers 16 bit words in SPI mode 0, automatically asserting CS on transfer start and deasserting on end. Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-12spi: efm32: Clean up non-DT pathsAxel Lin
This is a DT-only driver, so remove all non-DT paths. of_gpio_named_count() may fail, thus also add checking it's return value. efm32_spi_probe_dt() never fails, make it return void. Signed-off-by: Axel Lin <axel.lin@ingics.com> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-11spi: rspi: Add runtime PM support, using spi core auto_runtime_pmGeert Uytterhoeven
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-11spi: sh-msiof: Convert to spi core auto_runtime_pm frameworkGeert Uytterhoeven
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-11spi: sh-hspi: Add missing call to pm_runtime_disable() in failure pathGeert Uytterhoeven
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-10spi: coldfire-qspi: Prevent NULL pointer dereferenceAxel Lin
If pdata->cs_control is NULL, we will hit NULL pointer dereference in mcfqspi_cs_select() and mcfqspi_cs_deselect(). Thus add NULL test for pdata->cs_control in probe(). Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-10spi: clps711x: Provide label argument for devm_gpio_requestAxel Lin
The label argument was removed by commit 989847967cd762 spi: clps711x: Use devm_gpio_request(), add it back. This makes it easier to know the gpio usage in /sys/kernel/debug/gpio. Also remove unnecessary gpio_is_valid() checking, devm_gpio_request() returns error if the requested gpio is invalid. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-10spi: coldfire-qspi: Enable clock before calling spi_master_resumeAxel Lin
This ensures clock has been enabled before calling spi_master_resume(). while at it, also add checking return value of spi_master_suspend and spi_master_resume because they may fail. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-10spi/ti-qspi: Fix return from mmap pathSourav Poddar
mmap resource requirement is only for memory mapped operations. If the user does not populate mmap resource, dont call return, instead we go on for normal spi mode operations. Signed-off-by: Sourav Poddar <sourav.poddar@ti.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-07spi: s3c24xx: Add missing spi_master_{resume,suspend} calls to PM callbacksAxel Lin
This is required since commit 2025172e3280 "spi/bitbang: Use core message pump". spi-bitbang now uses core message pump, so it needs to call spi_master_suspend/ spi_master_resume to start/stop the queue while suspend/resume. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-07Merge remote-tracking branches 'spi/fix/ath79', 'spi/fix/atmel', ↵Mark Brown
'spi/fix/coldfire', 'spi/fix/fsl-dspi', 'spi/fix/imx' and 'spi/fix/topcliff-pch' into spi-linus
2014-03-06spi: pl022: Don't ignore power domain and amba bus at system suspendUlf Hansson
Previously only the resources controlled by the driver were put into low power state at system suspend. Both the amba bus and a potential power domain were ignored. Moreover, while putting the device into low power state we first brought it back to full power, but for no particular reason. To handle both issues above, use pm_runtime_force_suspend|resume() from the system suspend|resume callbacks. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-06spi: pl022: Let runtime PM callbacks be available for CONFIG_PMUlf Hansson
Convert to the SET_PM_RUNTIME_PM macro while defining the runtime PM callbacks. This means the callbacks becomes available for both CONFIG_PM_SLEEP and CONFIG_PM_RUNTIME, which is needed to handle the combinations of these scenarios. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-06Merge branch 'pm-drivers' of ↵Mark Brown
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm into spi-pl022
2014-03-05spi: fsl-dspi: Use SIMPLE_DEV_PM_OPS macroJingoo Han
Use SIMPLE_DEV_PM_OPS macro in order to make the code simpler. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-05spi: bcm63xx-hsspi: Use SIMPLE_DEV_PM_OPS macroJingoo Han
Use SIMPLE_DEV_PM_OPS macro in order to make the code simpler. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-05spi: omap-100k: fix spacing coding style issueJingoo Han
Fix the following checkpatch issues. ERROR: space prohibited after that open parenthesis '(' ERROR: space required before the open parenthesis '(' ERROR: trailing statements should be on next line ERROR: space required after that ',' (ctx:VxV) ERROR: spaces required around that '-=' (ctx:VxV) WARNING: sizeof *cs should be sizeof(*cs) Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-05spi: atmel: add missing spi_master_{resume,suspend} calls to PM callbacksWenyou Yang
The PM callbacks implemented by the spi-atmel driver don't call spi_master_{resume,suspend}, fix that. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-05spi: coldfire-qspi: Use core message handlingAxel Lin
Convert to use default implementation of transfer_one_message(). Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-05spi: coldfire-qspi: Remove unused dev field from struct mcfqspiAxel Lin
Also remove unused *res variable in mcfqspi_remove(). Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-05spi: coldfire-qspi: Fix getting correct address for *mcfqspiAxel Lin
dev_get_drvdata() returns the address of master rather than mcfqspi. Fixes: af361079 (spi/coldfire-qspi: Drop extra calls to spi_master_get in suspend/resume functions) Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org> Cc: stable@vger.kernel.org
2014-03-05spi: fsl-dspi: Fix getting correct address for masterAxel Lin
Current code set platform drvdata to dspi. However, the code in dspi_suspend() and dspi_resume() assumes the drvdata is the address of master. Fix it by setting platform drvdata to master. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org> Cc: stable@vger.kernel.org
2014-03-05spi: atmel: adopt pinctrl supportWenyou Yang
Amend the spi atmel pin controller to optionally take a pin control handle and set the state of the pins to: - "default" on boot, resume and before performing an spitransfer - "sleep" on suspend() This should make it possible to optimize energy usage for the pins both for the suspend/resume cycle Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-04spi: core: make zero length transfer valid againAtsushi Nemoto
Zero length transfer becomes invalid since "spi: core: Validate length of the transfers in message" commit, but it should be valid to support an odd device, for example, which requires long delay between chipselect and the first transfer, etc. Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Tested-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Mark Brown <broonie@linaro.org>
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2025-03-15 19:53:26 +0000