summaryrefslogtreecommitdiffstats
path: root/drivers/spi
AgeCommit message (Collapse)Author
2014-02-22spi: sh-msiof: Use the core cs_gpio field, and make it optionalGeert Uytterhoeven
In current implementation, CS is controlled by GPIO, which is passed through spi->controller_data. However, the MSIOF HW module has a function to output CS by itself, which is already enabled and actual switch will be done by pinmux. Store the GPIO number in the core cs_gpio field, and ignore it if it is an invalid (negative) GPIO number. Loosely based on a patch from Takashi Yoshii <takasi-y@ops.dti.ne.jp>. Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-22spi: sh-msiof: Add more register documentationGeert Uytterhoeven
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-22spi: sh-msiof: Change hz from unsigned long to u32Geert Uytterhoeven
Both spi_transfer.speed_hz and spi_master.max_speed_hz are u32 Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-22spi: sh-msiof: Typo in comment s/tx/rx/Geert Uytterhoeven
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-22spi: sh-msiof: Fix SPI bus population from DTGeert Uytterhoeven
DT doesn't instantiate SPI children if spi_master.dev.of_node is not set up properly. Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-22spi: core: Validate length of the transfers in messageIvan T. Ivanov
SPI transfer length should be multiple of SPI word size, where SPI word size should be power-of-two multiple Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-20spi: clps711x: Refactor to use core message parsingAxel Lin
Convert to use default implementation of transfer_one_message() which provides standard handling of delays and chip select management. Signed-off-by: Axel Lin <axel.lin@ingics.com> Tested-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-20spi: Add Qualcomm QUP SPI controller supportIvan T. Ivanov
Qualcomm Universal Peripheral (QUP) core is an AHB slave that provides a common data path (an output FIFO and an input FIFO) for serial peripheral interface (SPI) mini-core. SPI in master mode supports up to 50MHz, up to four chip selects, programmable data path from 4 bits to 32 bits and numerous protocol variants. Cc: Alok Chauhan <alokc@codeaurora.org> Cc: Gilad Avidov <gavidov@codeaurora.org> Cc: Kiran Gunda <kgunda@codeaurora.org> Cc: Sagar Dharia <sdharia@codeaurora.org> Cc: dsneddon@codeaurora.org Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-19spi/topcliff-pch: Fix DMA channelAlexander Stein
bus_num might be asigned dynamically to e.g. 32766. In this case the calculated DMA channel based on SPI bus number is bogus. Use SPI channel number instead for calculation. Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-19spi/topcliff-pch: Fix debug messageAlexander Stein
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-19spi: omap2-mcspi: Convert to let spi core validate transfer speedAxel Lin
Set master->max_speed_hz and master->min_speed_hz then spi core will handle checking transfer speed. So we can remove the same checking in this driver. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-19spi: omap2-mcspi: Remove list_empty checking in omap2_mcspi_transfer_one_messageAxel Lin
This checking is done in __spi_validate(). Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-18spi: mpc512x-psc: Remove redundant code to get bus_num from DTAxel Lin
For DT case, spi core will call of_alias_get_id() and set master->bus_num if it was not set. Signed-off-by: Axel Lin <axel.lin@ingics.com> Tested-by: Gerhard Sittig <gsi@denx.de> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-16spi: Remove explictly set bus_num and num_chipselect to default settingAxel Lin
The purpose of commit 1e8a52e18cfb "spi: By default setup spi_masters with 1 chipselect and dynamics bus number" is to avoid setting default value for bus_num and num_chipselect in spi master drivers. So let's remove the duplicate code. Signed-off-by: Axel Lin <axel.lin@ingics.com> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-By: David Daney <david.daney@cavium.com> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-16spi/fsl-dspi: Remove some coding sytle not in standardChao Fu
Remove some coding sytle not in standard in former code. Signed-off-by: Chao Fu <b44548@freescale.com> Reviewed-by: Xiubo Li <Li.Xiubo@freescale.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-16spi/fsl-dspi: Convert to use regmap and add big-endian supportChao Fu
Freescale DSPI module will have two endianess in different platform, but ARM is little endian. So when DSPI in big endian, core in little endian, readl and writel can not adjust R/W register in this condition. This patch will remove general readl/writel, and import regmap mechanism. Data endian will be transfered in regmap APIs. Documents: dspi add bool "big-endian" in dts node if DSPI module work in big endian. Signed-off-by: Chao Fu <b44548@freescale.com> Reviewed-by: Xiubo Li <Li.Xiubo@freescale.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-16spi: sun6i: Fix define for SUN6I_TFR_CTL_CS_MASKAxel Lin
Current code in sun6i_spi_set_cs() actually clears CPHA and CPOL bits which is obvious wrong. The define for SUN6I_TFR_CTL_CS_MASK is wrong. Fix it. Signed-off-by: Axel Lin <axel.lin@ingics.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-14spi: spi-imx: Propagate the real error code on platform_get_irq() failureFabio Estevam
No need to return a 'fake' return value on platform_get_irq() failure. Just return the error code itself instead. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-14spi: spi-mxs: Propagate the real error code on platform_get_irq() failureFabio Estevam
No need to return a 'fake' return value on platform_get_irq() failure. Just return the error code itself instead. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marex@denx.de> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-14spi: au1550: Convert to let spi core handle checking transfer speedAxel Lin
By setting master->max_speed_hz and master->min_speed_hz, spi core will handle checking transfer speed. So we can remove the same checking in this driver. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-14spi: topcliff-pch: Convert to use master->max_speed_hzAxel Lin
Set "master->max_speed_hz = PCH_MAX_BAUDRATE" then we can remove pch_spi_setup. In additional, pspi->max_speed_hz will never be 0 because it's default value will be set to master->max_speed_hz. Also remove list_empty checking in pch_spi_transfer() because the checking is done by spi core. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-14spi: bfin5xx: Remove unused last_transfer pointer in bfin_spi_giveback()Axel Lin
Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-14spi: ep93xx: Convert to let spi core handle checking transfer speedAxel Lin
By setting master->max_speed_hz and master->min_speed_hz, spi core will handle checking transfer speed. So we can remove the same checking in this driver. Signed-off-by: Axel Lin <axel.lin@ingics.com> Acked-by: Mika Westerberg <mika.westerberg@iki.fi> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-14spi: nuc900: Remove unused fields from struct nuc900_spiAxel Lin
Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-14spi: bfin5xx: Remove duplicate code to check spi->modeAxel Lin
This checking is already done in the implementation of spi_setup(). Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-14spi: s3c24xx: Convert to let spi core validate bits_per_wordAxel Lin
Set bits_per_word_mask so spi core will reject transfers that attempt to use an unsupported bits_per_word value. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-14spi: Clean up probe and remove functionsJean Delvare
While backporting 33cf00e5 ("spi: attach/detach SPI device to the ACPI power domain"), I noticed that the code changes were suboptimal: * Why use &spi->dev when we have dev at hand? * After fixing the above, spi is used only once, so we don't really need a local variable for it. This results in the following clean-up. Signed-off-by: Jean Delvare <jdelvare@suse.de> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-12spi: Make max_tx and max_rx the same typeMark Brown
Prevents spurious compiler warnings. Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-12spi: Remove duplicate code to check chip_selectAxel Lin
In spi_add_device(), we have the code to validate spi->chip_select. So remove the duplicate code in various drivers. Signed-off-by: Axel Lin <axel.lin@ingics.com> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-11spi: octeon: Remove unused bits_per_word from struct octeon_spi_setupAxel Lin
Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-11spi: orion: Convert to let spi core validate xfer->bits_per_wordAxel Lin
Set bits_per_word_mask so spi core will reject transfers that attempt to use an unsupported bits_per_word value. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-11spi: sc18is602: Move checking chip_select for SC18IS602 to sc18is602_setupAxel Lin
So it will be checked when spi device is added onto the spi bus. spi_add_device() calls spi_setup() which then calls spi->master->setup(). No need to check it every time sc18is602_transfer_one() is called. Signed-off-by: Axel Lin <axel.lin@ingics.com> Acked-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-11Merge remote-tracking branches 'spi/fix/doc', 'spi/fix/nuc900' and ↵Mark Brown
'spi/fix/rspi' into spi-linus
2014-02-11Merge remote-tracking branch 'spi/fix/core' into spi-linusMark Brown
2014-02-11spi: tegra20-slink: Convert to use master->max_speed_hzAxel Lin
Use master->max_speed_hz instead of tspi->spi_max_frequency, so spi core will handle checking transfer speed. In additional, since commit 052eb2d49006 'spi: core: Set max_speed_hz of spi_device default to max_speed_hz of controller', spi core will also set default spi->max_speed_hz if it is not set. So remove the duplicate code in tegra_slink_setup. Signed-off-by: Axel Lin <axel.lin@ingics.com> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-11spi: tegra20-sflash: Convert to use master->max_speed_hzAxel Lin
Use master->max_speed_hz instead of tspi->spi_max_frequency, so spi core will handle checking transfer speed. In additional, since commit 052eb2d49006 'spi: core: Set max_speed_hz of spi_device default to max_speed_hz of controller', spi core will also set default spi->max_speed_hz if it is not set. So remove tegra_sflash_setup(). Signed-off-by: Axel Lin <axel.lin@ingics.com> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-11spi: tegra114: Convert to use master->max_speed_hzAxel Lin
Use master->max_speed_hz instead of tspi->spi_max_frequency, so spi core will handle checking transfer speed. In additional, since commit 052eb2d49006 'spi: core: Set max_speed_hz of spi_device default to max_speed_hz of controller', spi core will also set default spi->max_speed_hz if it is not set. So remove the duplicate code in tegra_spi_setup. Signed-off-by: Axel Lin <axel.lin@ingics.com> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-10spi: txx9: Convert to let spi core handle checking transfer speedAxel Lin
By setting master->max_speed_hz and master->min_speed_hz, spi core will handle checking transfer speed. Then we can remove the same checking in this driver. Signed-off-by: Axel Lin <axel.lin@ingics.com> Reviewed-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-10spi: core: Set max_speed_hz of spi_device default to max_speed_hz of controllerAxel Lin
In __spi_validate(), xfer->speed_hz is set to be spi->max_speed_hz if it is not set for this transfer. However, if spi->max_speed_hz is also not set, xfer->speed_hz is 0. Some drivers (e.g. au1550, tegra114, tegra20-sflash, tegra20-slink, etc.) then use below code to avoid setting xfer->speed_hz to 0. /* Set speed to the spi max fequency if spi device has not set */ spi->max_speed_hz = spi->max_speed_hz ? : tspi->spi_max_frequency; Let's handle it in spi core. If spi->max_speed_hz is not set, make it default to spi->master->max_speed_hz. So In __spi_validate() if both xfer->speed_hz and spi->max_speed_hz are not set, xfer->speed_hz will be set to spi->master->max_speed_hz. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-10spi: omap2: use SUPERH, not SHPaul Bolle
Commit 0079aae0f1e6 ("spi: omap2: Add build dependencies for writel_relaxed()") added an optional Kconfig dependency on SH. That Kconfig symbol doesn't exist. Apparently SUPERH was intended. Use that. Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-10spi: Use reinit_completion at appropriate placesAxel Lin
Calling init_completion() once is enough. For the rest of the iterations, call reinit_completion() instead. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-10spi: omap-100k: Remove unused fields from struct omap1_spi100kAxel Lin
Both *master and state are not really used, remove them. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-10spi: omap-100k: Remove unused pointer in omap1_spi100k_txrx_pio()Christian Engelmayer
Remove unused devdata pointer 'spi100k' in function omap1_spi100k_txrx_pio(). Detected by Coverity: CID 1077869. Signed-off-by: Christian Engelmayer <cengelma@gmx.at> Reviewed-by: Jingoo Han <jg1.han@samsung.com> Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-10spi: omap-100k: Remove unused MOD_REG_BIT macroAxel Lin
Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-07spi/s3c64xx: Remove code no longer needed as a result of S3C_DMA removalMark Brown
Remove functions that only had an effect when using S3C_DMA and inline dmaengine_terminate_all() since it's pointless to have a function which expands to a single function call. Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-07spi/s3c64xx: Remove S3C_DMA supportMark Brown
All the platforms which use the old S3C_DMA API have now been converted to dmaengine so we can remove the legacy code from the driver, simplifying maintenance. Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-07spi/s3c64xx: Use core DMA mapping code with dmaengineMark Brown
When using dmaengine allow the core to do the DMA mapping. We still need local mapping code for the non-dmaengine case so this doesn't save us anything for now. Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-07spi: Use SPI_BPW_MASK macro at appropriate placesAxel Lin
Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-07spi: mxs: Use list_for_each_entry to iterate over transfer listAxel Lin
We don't modify the list entry while iterating the transfer list. So use list_for_each_entry instead of list_for_each_entry_safe. Signed-off-by: Axel Lin <axel.lin@ingics.com> Acked-by: Marek Vasut <marex@denx.de> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-07spi: orion: Let spi core handle checking transfer speedAxel Lin
Since commit a2fd4f9fa3b9 'spi: Support transfer speed checking in the core', the SPI core validates the desired speed of a given transfer against the minimum and maximum speeds supported by the controller. So we can remove the same code in this driver and let spi core handle checking the desired speed of a given transfer. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2025-03-16 02:10:02 +0000