| Age | Commit message (Collapse) | Author |
|---|
|
This patch fixes the following bug:
The thermal framework creates a temp*_crit interface, only when
the get_crit_temp pointer is defined. But during the _unregister_
path, without checking for the function definition, it is trying to
remove the temp*_crit interface.
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Several ACPI drivers fail to build if CONFIG_NET is unset, because
they refer to things depending on CONFIG_THERMAL that in turn depends
on CONFIG_NET. However, CONFIG_THERMAL doesn't really need to depend
on CONFIG_NET, because the only part of it requiring CONFIG_NET is
the netlink interface in thermal_sys.c.
Put the netlink interface in thermal_sys.c under #ifdef CONFIG_NET
and remove the dependency of CONFIG_THERMAL on CONFIG_NET from
drivers/thermal/Kconfig.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Len Brown <lenb@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Luming Yu <luming.yu@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
|
|
This patch adds event notification support to the generic
thermal sysfs framework in the kernel. The notification is in the
form of a netlink event.
Signed-off-by: R.Durgadoss <durgadoss.r@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
And while touching that function definition do something about the disaster
of formatting there.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Initialize sysfs attributes before device_create_file call.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=15548
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Greg KH <gregkh@suse.de>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Len Brown <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
|
|
|
|
state is unsigned long so the test did not work.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Otherwise polling will continue for the thermal zone even when
it is no longer needed, for example because forced passive cooling
was disabled.
Signed-off-by: Frans Pop <elendil@planet.nl>
Acked-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Setting polling_delay is useless as passive_delay has priority,
so the value shown in proc isn't the actual polling delay. It
also gives the impression to the user that he can change the
polling interval through proc, while in fact he can't.
Also, unset passive_delay when the forced passive trip point is
unbound to allow polling to be disabled.
Signed-off-by: Frans Pop <elendil@planet.nl>
Acked-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Values below 1000 milli-celsius don't make sense and can cause the
system to go into a thermal heart attack: the actual temperature
will always be lower and thus the system will be throttled down to
its lowest setting.
An additional problem is that values below 1000 will show as 0 in
/proc/acpi/thermal/TZx/trip_points:passive.
cat passive
0
echo -n 90 >passive
bash: echo: write error: Invalid argument
echo -n 90000 >passive
cat passive
90000
Signed-off-by: Frans Pop <elendil@planet.nl>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Make the trip_point_N_type sysfs files return a string ending in EOL for
consistency with other sysfs files.
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
The return value of the get_temp function is not checked when doing a
thermal zone update. This may lead to a critical shutdown if get_temp
fails and the content of the temp variable is incorrectly set higher than
the critical trip point.
This has been observed on a system with incorrect ACPI implementation
where the corresponding methods were not serialized and therefore
sometimes triggered ACPI errors (AE_ALREADY_EXISTS). The following
critical shutdowns indicated a temperature of 2097 C, which was obviously
wrong.
The patch adds a return value check that jumps over all trip point
evaluations printing a warning if get_temp fails. The trip points are
evaluated again on the next polling interval with successful get_temp
execution.
Signed-off-by: Michael Brunner <mibru@gmx.de>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch fixes a regression caused by commit
b1569e99c795bf83b4ddf41c4f1c42761ab7f75e
"ACPI: move thermal trip handling to generic thermal layer"
which accidentally changed trip point trigger condition to
temp > trip_temp
This patch changes the trigger condition back to
temp >= trip_temp
Signed-off-by: Vladimir Zajac <eightgraph@gmail.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Due to poor thermal design or Linux driving hardware outside its thermal
envelope, some systems will reach critical temperature and shut down
under high load. This patch adds support for forcing a polling-based
passive trip point if the firmware doesn't provide one. The assumption
is made that the processor is the most practical means to reduce the
dynamic heat generation, so hitting the passive thermal limit will cause
the CPU to be throttled until the temperature stabalises around the
defined value.
UI is provided via a "passive" sysfs entry in the thermal zone
directory. It accepts a decimal value in millidegrees celsius, or "0" to
disable the functionality. Default behaviour is for this functionality
to be disabled.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
The ACPI code currently carries its own thermal trip handling, meaning that
any other thermal implementation will need to reimplement it. Move the code
to the generic thermal layer.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
The thermal API currently uses strings to pass values to userspace. This
makes it difficult to use from within the kernel. Change the interface
to use integers and fix up the consumers.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
A bug in libsensors <= 2.10.6 is exposed
when this new hwmon I/F is enabled.
Create CONFIG_THERMAL_HWMON=n
until some time after libsensors 2.10.7 ships
so those users can run the latest kernel.
libsensors 3.x is already fixed -- those users
can use CONFIG_THERMAL_HWMON=y now.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Acked-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
thermal_sys was already the name of the resulting module,
and it is built from this one source file.
Signed-off-by: Len Brown <len.brown@intel.com>
|
