| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
"Assorted fixes and cleanups to the existing drivers plus a new driver
for IMS Passenger Control Unit device they use for ther in-flight
entertainment system."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (44 commits)
Input: trackpoint - Optimize trackpoint init to use power-on reset
Input: apbps2 - convert to devm_ioremap_resource()
Input: ALPS - use %ph to print buffers
ARM - shmobile: Armadillo800EVA: Move st1232 reset pin handling
Input: st1232 - add reset pin handling
Input: st1232 - convert to devm_* infrastructure
Input: MT - handle semi-mt devices in core
Input: adxl34x - use spi_get_drvdata()
Input: ad7877 - use spi_get_drvdata() and spi_set_drvdata()
Input: ads7846 - use spi_get_drvdata() and spi_set_drvdata()
Input: ims-pcu - fix a memory leak on error
Input: sysrq - supplement reset sequence with timeout functionality
Input: tegra-kbc - support for defining row/columns based on SoC
Input: imx_keypad - switch to using managed resources
Input: arc_ps2 - add support for device tree
Input: mma8450 - fix signed 12bits to 32bits conversion
Input: eeti_ts - remove redundant null check
Input: edt-ft5x06 - remove redundant null check before kfree
Input: ad714x - add CONFIG_PM_SLEEP to suspend/resume functions
Input: adxl34x - add CONFIG_PM_SLEEP to suspend/resume functions
...
|
|
We first tried to avoid updating atime/mtime entirely (commit
b0de59b5733d: "TTY: do not update atime/mtime on read/write"), and then
limited it to only update it occasionally (commit 37b7f3c76595: "TTY:
fix atime/mtime regression"), but it turns out that this was both
insufficient and overkill.
It was insufficient because we let people attach to the shared ptmx node
to see activity without even reading atime/mtime, and it was overkill
because the "only once a minute" means that you can't really tell an
idle person from an active one with 'w'.
So this tries to fix the problem properly. It marks the shared ptmx
node as un-notifiable, and it lowers the "only once a minute" to a few
seconds instead - still long enough that you can't time individual
keystrokes, but short enough that you can tell whether somebody is
active or not.
Reported-by: Simon Kirby <sim@hostway.ca>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver update from Greg Kroah-Hartman:
"Here's the big tty/serial driver merge request for 3.10-rc1
Once again, Jiri has a number of TTY driver fixes and cleanups, and
Peter Hurley came through with a bunch of ldisc fixes that resolve a
number of reported issues. There are some other serial driver
cleanups as well.
All of these have been in the linux-next tree for a while"
* tag 'tty-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (117 commits)
tty/serial/sirf: fix MODULE_DEVICE_TABLE
serial: mxs: drop superfluous {get|put}_device
serial: mxs: fix buffer overflow
ARM: PL011: add support for extended FIFO-size of PL011-r1p5
serial_core.c: add put_device() after device_find_child()
tty: Fix unsafe bit ops in tty_throttle_safe/unthrottle_safe
serial: sccnxp: Replace pdata.init/exit with regulator API
serial: sccnxp: Do not override device name
TTY: pty, fix compilation warning
TTY: rocket, fix compilation warning
TTY: ircomm: fix DTR being raised on hang up
TTY: synclinkmp: fix DTR being raised on hang up
TTY: synclink_gt: fix DTR being raised on hang up
TTY: synclink: fix DTR being raised on hang up
serial: 8250_dw: Fix the stub for dw8250_probe_acpi()
serial: 8250_dw: Convert to devm_ioremap()
serial: 8250_dw: Set port capabilities based on CPR register
serial: 8250_dw: Let ACPI code extract the DMA client info
serial: 8250_dw: Support clk framework also with ACPI
serial: 8250_dw: Enable runtime PM
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver update from Greg Kroah-Hartman:
"Here's the big char / misc driver update for 3.10-rc1
A number of various driver updates, the majority being new
functionality in the MEI driver subsystem (it's now a subsystem, it
started out just a single driver), extcon updates, memory updates,
hyper-v updates, and a bunch of other small stuff that doesn't fit in
any other tree.
All of these have been in linux-next for a while"
* tag 'char-misc-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (148 commits)
Tools: hv: Fix a checkpatch warning
tools: hv: skip iso9660 mounts in hv_vss_daemon
tools: hv: use FIFREEZE/FITHAW in hv_vss_daemon
tools: hv: use getmntent in hv_vss_daemon
Tools: hv: Fix a checkpatch warning
tools: hv: fix checks for origin of netlink message in hv_vss_daemon
Tools: hv: fix warnings in hv_vss_daemon
misc: mark spear13xx-pcie-gadget as broken
mei: fix krealloc() misuse in in mei_cl_irq_read_msg()
mei: reduce flow control only for completed messages
mei: reseting -> resetting
mei: fix reading large reposnes
mei: revamp mei_irq_read_client_message function
mei: revamp mei_amthif_irq_read_message
mei: revamp hbm state machine
Revert "drivers/scsi: use module_pcmcia_driver() in pcmcia drivers"
Revert "scsi: pcmcia: nsp_cs: remove module init/exit function prototypes"
scsi: pcmcia: nsp_cs: remove module init/exit function prototypes
mei: wd: fix line over 80 characters
misc: tsl2550: Use dev_pm_ops
...
|
|
In commit b0de59b5733d ("TTY: do not update atime/mtime on read/write")
we removed timestamps from tty inodes to fix a security issue and waited
if something breaks. Well, 'w', the utility to find out logged users
and their inactivity time broke. It shows that users are inactive since
the time they logged in.
To revert to the old behaviour while still preventing attackers to
guess the password length, we update the timestamps in one-minute
intervals by this patch.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This fixes building the sirfsorc-uart driver as a loadable module,
which uses an incorrect MODULE_DEVICE_TABLE, by changing the reference to the
correct symbol.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Driver core already takes care of refcounting, no need to do this on
driver level again.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
SMATCH correctly found an off-by-one error:
drivers/tty/serial/mxs-auart.c:889 auart_console_write() error: buffer overflow 'auart_port' 5 <= 5
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The latest r1p5-revision of the ARM PL011 UART has 32-byte FIFOs,
while all earlier ones have 16-byte FIFOs. This patch suggests
a way to set the FIFO-size correctly & flexibly by using a member
function named get_fifosize, rather than using the fifosize member
variable. The function takes the UARTPeriphID, and returns the
correct FIFO size.
Signed-off-by: Jongsung Kim <neidhard.kim@lge.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The serial core uses device_find_child() but does not drop the reference to
the retrieved child after using it. This patch add the missing put_device().
What I have done to test this issue.
I used a machine with an AMBA PL011 serial driver. I tested the patch on
next-20120408 because the last branch [next-20120415] does not boot on this
board.
For test purpose, I added some pr_info() messages to print the refcount
after device_find_child() (lines: 1937,2009), and after put_device()
(lines: 1947, 2021).
Boot the machine *without* put_device(). Then:
echo reboot > /sys/power/disk
echo disk > /sys/power/state
[ 87.058575] uart_suspend_port:1937 refcount 4
[ 87.058582] uart_suspend_port:1947 refcount 4
[ 87.098083] uart_resume_port:2009refcount 5
[ 87.098088] uart_resume_port:2021 refcount 5
echo disk > /sys/power/state
[ 103.055574] uart_suspend_port:1937 refcount 6
[ 103.055580] uart_suspend_port:1947 refcount 6
[ 103.095322] uart_resume_port:2009 refcount 7
[ 103.095327] uart_resume_port:2021 refcount 7
echo disk > /sys/power/state
[ 252.459580] uart_suspend_port:1937 refcount 8
[ 252.459586] uart_suspend_port:1947 refcount 8
[ 252.499611] uart_resume_port:2009 refcount 9
[ 252.499616] uart_resume_port:2021 refcount 9
The refcount continuously increased.
Boot the machine *with* this patch. Then:
echo reboot > /sys/power/disk
echo disk > /sys/power/state
[ 159.333559] uart_suspend_port:1937 refcount 4
[ 159.333566] uart_suspend_port:1947 refcount 3
[ 159.372751] uart_resume_port:2009 refcount 4
[ 159.372755] uart_resume_port:2021 refcount 3
echo disk > /sys/power/state
[ 185.713614] uart_suspend_port:1937 refcount 4
[ 185.713621] uart_suspend_port:1947 refcount 3
[ 185.752935] uart_resume_port:2009 refcount 4
[ 185.752940] uart_resume_port:2021 refcount 3
echo disk > /sys/power/state
[ 207.458584] uart_suspend_port:1937 refcount 4
[ 207.458591] uart_suspend_port:1947 refcount 3
[ 207.498598] uart_resume_port:2009 refcount 4
[ 207.498605] uart_resume_port:2021 refcount 3
The refcount correctly handled.
Signed-off-by: Federico Vaga <federico.vaga@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
tty->flags needs to be atomically modified.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Typical usage of pdata.init/exit is enable/disable power and/or toggle
reset for the target chip.
This patch replaces these callbacks with regulator API.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When CONFIG_UNIX98_PTYS is unset, we see this warning in pty:
drivers/tty/pty.c:409:13: warning: ‘pty_unix98_shutdown’ defined but not used
Fix that by moving the function to a section which depends on that
config.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: Toralf Foerster <toralf.foerster@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When CONFIG_PCI is unset, we see these warnings in rocket:
drivers/tty/rocket.c:3140:13: warning: 'rmSpeakerReset' defined but not used
drivers/tty/rocket.c:2599:12: warning: 'sPCIInitController' defined but not used
Fix those by moving the functions to one place and make them depend on
CONFIG_PCI.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: Toralf Foerster <toralf.foerster@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want the fixes here.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want the fixes in there.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure to check ASYNC_INITIALISED before raising DTR when waking up
from blocked open in block_til_ready.
Currently DTR could get raised at hang up as a blocked process would
raise DTR unconditionally before checking for hang up and returning.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure to check ASYNC_INITIALISED before raising DTR when waking up
from blocked open in block_til_ready.
Currently DTR could get raised at hang up as a blocked process would
raise DTR unconditionally before checking for hang up and returning.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure to check ASYNC_INITIALISED before raising DTR when waking up
from blocked open in block_til_ready.
Currently DTR could get raised at hang up as a blocked process would
raise DTR unconditionally before checking for hang up and returning.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This fixes the stub for dw8250_probe_acpi() that is used
when compiling without ACPI enabled. The argument type was
wrong.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use resource managed ioremap.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Designware UART has an optional support for 16750
compatible Auto Flow Control. This will enable it based on
the AFCE bit in Component Parameter Register.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The new ACPI DMA helpers in dmaengine API can take care of
extracting all the necessary information regarding DMA. The
driver does not need to do this separately any more.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Lynxpoint LPSS peripheral clocks are now handled in clk
framework so the drivers do not need to take care of them
manually. In dw8250_probe_acpi(), the uartclk is now taken
from the driver_data only if it was not already set.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This allows ACPI to put the device to D3 when it's not used.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some slave channel parameters will be always the same. For
example, direction for the Rx channel will always be
DMA_DEV_TO_MEM and DMA_MEM_TO_DEV for Tx channel.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The helper functions in dmaengine API allow the drivers to
request slave channels without the filter parameters. They
will attempt to extract the needed DMA client information
from DT or ACPI, but if such information is not available
the filter parameters can still be used.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Overrun, parity and framing errors should be handled in
8250_core. This also adds check for the dma_status and exits
if the channel is not idle.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Removing one unneeded uart_write_wakeup(). There is no need
to start PIO transfer unless DMA fails, so this also changes
serial8250_tx_dma() to return 0 unless that is the case.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There are a few bugs in the samsung serial driver when built as a
loadable module, which makes the console code unavailable, as well as
giving no access to the 'printascii' early debug function. This adds
the appropriate compile time conditionals.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The registers for the Samsung S3C serial port are currently defined in
the platform specific arch/arm/plat-samsung/include/plat/regs-serial.h
file, which is not visible to multiplatform capable drivers.
Unfortunately, it is not possible to move the file into a more local
place as we should normally try to, because the same registers
may be used in one of four places:
* In the driver itself
* In platform-independent ARM code for early debug output
* In platform_data definitions
* In the Samsung platform power management code
I have also found no way to logically split out a platform_data
file, other than possibly move everything into
include/linux/platform_data, which also felt wrong. The only
part of this file that makes sense to keep specific to the s3c24xx
platform are the virtual and physical addresses defined here,
which are needed in no other location.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
With the common clock interface, there is no way to provide the
"clock_source" sysfs attribute for the samsung serial ports. Given that
this file was purely informational and had fixed contents, we have reason
to believe that no user space programs were relying on it.
The sysfs file is not documented in the ABI docs.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As Ilya Zykov identified in his patch 'PROBLEM: Race condition in
tty buffer's function flush_to_ldisc()', a race condition exists
which allows a parallel flush_to_ldisc() to flush and free the tty
flip buffers while those buffers are in-use. For example,
CPU 0 | CPU 1 | CPU 2
| flush_to_ldisc() |
| grab spin lock |
tty_buffer_flush() | | flush_to_ldisc()
wait for spin lock | | wait for spin lock
| if (!test_and_set_bit(TTYP_FLUSHING)) |
| while (next flip buffer) |
| ... |
| drop spin lock |
grab spin lock | |
if (test_bit(TTYP_FLUSHING)) | |
set_bit(TTYP_FLUSHPENDING) | receive_buf() |
drop spin lock | |
| | grab spin lock
| | if (!test_and_set_bit(TTYP_FLUSHING))
| | if (test_bit(TTYP_FLUSHPENDING))
| | __tty_buffer_flush()
CPU 2 has just flushed and freed all tty flip buffers while CPU 1 is
transferring data from the head flip buffer.
The original patch was rejected under the assumption that parallel
flush_to_ldisc() was not possible. Because of necessary changes to
the workqueue api, work items can execute in parallel on SMP.
This patch differs slightly from the original patch by testing for
a pending flush _after_ each receive_buf(), since TTYP_FLUSHPENDING
can only be set while the lock is dropped around receive_buf().
Reported-by: Ilya Zykov <linux@izyk.ru>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Ilya Zykov <linux@izyk.ru>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
mxser_module_init()
There is a bug in resources deallocation code in mxser_probe() and
mxser_module_init(). As soon as variable 'i' is unsigned int, cycle
termination condition i >= 0 is always true. The patch fixes the issue.
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 77e372a3d82e5e4878ce1962207edd766773cc76.
Checking for disabled resources board breaks detection pnp on another
board "AMI UEFI implementation (Version: 0406 Release Date: 06/06/2012)".
I'm working with the reporter of the original bug to write and test
a better fix.
https://bugzilla.redhat.com/show_bug.cgi?id=928246
Signed-off-by: Sean Young <sean@mess.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Partially reverts 1776fd059c40907297d6c26c51876575d63fd9e2
that introduced regression reported by Paul Walmsley.
This commit restores setting granularity in SCR register
and adds note about comments below being inconsistent with
actual code.
Signed-off-by: Alexey Pelykh <alexey.pelykh@gmail.com>
Tested-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Following patch will fix build error if CONFIG_DMA_ENGINE is unset.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Chanho Min <chanho.min@lge.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some devices have too few buttons, which it makes it hard to have
a reset combo that won't trigger automatically. As such a
timeout functionality that requires the combination to be held for
a given amount of time before triggering is introduced.
If a key combo is recognized and held for a 'timeout' amount of time,
the system triggers a reset. If the timeout value is omitted the
driver simply ignores the functionality.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
We need the fixes here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This picks up the fixes in 3.9-rc5 that we need here.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In DMA support, The received data is not pushed to tty until the DMA buffer
is filled. But some megabyte rate chips such as BT expect fast response and
data should be pushed immediately. In order to fix this issue, We suggest
the use of the timer for polling DMA buffer.
In our test, no data loss occurred at high-baudrate as compared with interrupt-
driven (We tested with 3Mbps).
We changes:
- We add timer for polling. If we set poll_timer to 10, every 10ms,
timer handler checks the residue in the dma buffer and transfer data
to the tty. Also, last_residue is updated for the next polling.
- poll_timeout is used to prevent the timer's system cost.
If poll_timeout is set to 3000 and no data is received in 3 seconds,
we inactivate poll timer and driver falls back to interrupt-driven.
When data is received again in FIFO and UART irq is occurred, we switch
back to DMA mode and start polling.
- We use consistent DMA mappings to avoid from the frequent cache operation
of the timer function for default.
- pl011_dma_rx_chars is modified. the pending size is recalculated because
data can be taken by polling.
- the polling time is adjusted if dma rx poll is enabled but no rate is
specified. Ideal polling interval to push 1 character at every interval
is the reciprocal of 'baud rate / 10 line bits per character / 1000 ms
per sec'. But It is very aggressive to system. Experimentally,
'10000000 / baud' is suitable to receive dozens of characters. the poll rate
can be specified statically by dma_rx_poll_rate of the platform data as well.
Changes compared to v1:
- Use of consistent DMA mappings.
- Added dma_rx_poll_rate in platform data to specify the polling interval.
- Added dma_rx_poll_timeout in platform data to specify the polling timeout.
Changes compared to v2:
- Use of consistent DMA mappings for default.
- Added dma_rx_poll_enable in platform data to adjust the polling time
according to the baud rate.
- remove unnecessary lock from the polling function.
Signed-off-by: Chanho Min <chanho.min@lge.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This commit implements support for using the clk api; this lets us use
the "clocks" property with device tree, instead of having to use
clock-frequency.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The no_console_suspend option allows the console to write to the UART
during early resume, before the serial port itself is resumed. Such
writes hang indefinitely waiting for TX ready.
This adds a check to the console putchar function to drop characters
instead of hanging if the port hasn't been initialized. That way, we
can use no_console_suspend without risk of hanging.
Signed-off-by: Michael Spang <spang@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This closes a window where the system may hang in resume as soon as the
UART interrupt is enabled and before the mask is restored. The hang occurs
because the driver can't handle IRQs it thinks are masked.
Signed-off-by: Michael Spang <spang@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since the interrupt mask register is not preserved across system suspend
and it defaults to all interrupts enabled, it is not enough to disable
UART interrupt.
This patch adds free_irq to port shutdown and mask setting to port
startup to handle IRQ disabling in a suspend-friendly way. In addition,
a bug caused by multiple request_irq calls in port startup callback is
fixed.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY/serial fixes from Greg Kroah-Hartman:
"Here are some tty/serial driver fixes for 3.9.
The big thing here is the fix for the huge mess we caused renaming the
8250 driver accidentally in the 3.7 kernel release, without realizing
that there were users of the module options that suddenly broke. This
is now resolved, and, to top the injury off, we have a backwards-
compatible option for those users who got used to the new name since
3.7. Ugh, sorry about that.
Other than that, some other minor fixes for issues that have been
reported by users."
* tag 'tty-3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Xilinx: ARM: UART: clear pending irqs before enabling irqs
TTY: 8250, deprecated 8250_core.* options
TTY: 8250, revert module name change
serial: 8250_pci: Add WCH CH352 quirk to avoid Xscale detection
tty: atmel_serial_probe(): index of atmel_ports[] fix
|
|
Consider a situation where I have an ARM based system
and therefore no legacy ports. Say, I have two
memory-mapped ports. I use device tree to describe the
ports. What would be the config options I set so that
I get only the two ports in my system? I do not want
legacy ports being created automatically and I want
it to be flexible enough that it creates the devices
based only on the device tree. I expected setting
SERIAL_8250_RUNTIME_UARTS = 0 to work because the
description said, "Set this to the maximum number of
serial ports you want the kernel to register at boot
time." Unfortunately, even though SERIAL_8250_NR_UARTS
was set to the default value of 4, I did not get any device
nodes (because SERIAL_8250_RUNTIME_UARTS was 0). This
is what this change is addressing.
SERIAL_8250_NR_UARTS controls the maximum number of ports
you can support. SERIAL_8250_RUNTIME_UARTS specifies the
number of ports you want to create automatically for legacy
ports at boot time. All other ports will be created
when serial8250_register_port is called (and if does not exceed
the total number of supported ports as specified by
SERIAL_8250_NR_UARTS).
Signed-off-by: Karthik Manamcheri <karthik.manamcheri@ni.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"stable fodder; assorted deadlock fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
vt: synchronize_rcu() under spinlock is not nice...
Nest rename_lock inside vfsmount_lock
Don't bother with redoing rw_verify_area() from default_file_splice_from()
|
