| Age | Commit message (Collapse) | Author |
|---|
|
This patch (as1573) adds hrtimer support for managing ehci-hcd's
periodic schedule. There are two issues to deal with.
First, the schedule's state (on or off) must not be changed until the
hardware status has caught up with the current command. This is
handled by an hrtimer event that polls at 1-ms intervals to see when
the Periodic Schedule Status (PSS) flag matches the Periodic Schedule
Enable (PSE) value.
Second, the schedule should not be turned off as soon as it becomes
empty. Turning the schedule on and off takes time, so we want to wait
until the schedule has been empty for a suitable period before turning
it off. This is handled by an hrtimer event that gets set to expire
10 ms after the periodic schedule becomes empty.
The existing code polls (for up to 1125 us and with interrupts
disabled!) to check the status, and doesn't implement a delay before
turning off the schedule. Furthermore, if the polling fails then the
driver decides that the controller has died. This has caused problems
for several people; some controllers can take 10 ms or more to turn
off their periodic schedules.
This patch fixes these issues. It also makes the "broken_periodic"
workaround unnecessary; there is no longer any danger of turning off
the periodic schedule after it has been on for less than 1 ms.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch (as1564c) converts the EHCI platform drivers to use the
central ehci_setup() routine for generic controller initialization
rather than each having its own idiosyncratic approach.
The major point of difficulty lies in ehci-pci's many vendor- and
device-specific workarounds. Some of them have to be applied before
calling ehci_setup() and some after, which necessitates a fair amount
of code motion. The other platform drivers require much smaller
changes.
One point not addressed by the patch is whether ports should be
powered on or off following initialization. The different drivers
appear to handle this pretty much at random. In fact it shouldn't
matter, because the hub driver turns on power to all ports when it
binds to the root hub. Straightening that out will be left for
another day.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch (as1563) removes a lot of duplicated code by moving the
EHCI controller suspend/resume routines into the core driver, where
the various platform drivers can invoke them as needed.
Not only does this simplify these platform drivers, this also makes it
easier for other platform drivers to add suspend/resume support in the
future.
Note: The patch does not touch the ehci-fsl.c file, because its
approach to suspend and resume is so different from all the others.
It will have to be handled specially by its maintainer.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch (as1558) fixes a problem affecting several ASUS computers:
The machine crashes or corrupts memory when going into suspend if the
ehci-hcd driver is bound to any controllers. Users have been forced
to unbind or unload ehci-hcd before putting their systems to sleep.
After extensive testing, it was determined that the machines don't
like going into suspend when any EHCI controllers are in the PCI D3
power state. Presumably this is a firmware bug, but there's nothing
we can do about it except to avoid putting the controllers in D3
during system sleep.
The patch adds a new flag to indicate whether the problem is present,
and avoids changing the controller's power state if the flag is set.
Runtime suspend is unaffected; this matters only for system suspend.
However as a side effect, the controller will not respond to remote
wakeup requests while the system is asleep. Hence USB wakeup is not
functional -- but of course, this is already true in the current state
of affairs.
A similar patch has already been applied as commit
151b61284776be2d6f02d48c23c3625678960b97 (USB: EHCI: fix crash during
suspend on ASUS computers). The patch supersedes that one and reverts
it. There are two differences:
The old patch added the flag at the USB level; this patch
adds it at the PCI level.
The old patch applied to all chipsets with the same vendor,
subsystem vendor, and product IDs; this patch makes an
exception for a known-good system (based on DMI information).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Dâniel Fraga <fragabr@gmail.com>
Tested-by: Andrey Rahmatullin <wrar@wrar.name>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 1996e6c572969a8cf6d7fa97eef621219acd94a9.
It turned out to not be needed, now that the real fix has been
committed.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch (as1556) works around a bug in the Philips ISP1562 EHCI
controller. Although the controller claims to support frame-list
lengths smaller than the default of 1024 for its periodic schedule, in
fact smaller values don't work. A new quirk flag is added to indicate
when the bug is present, and if it is then the schedule size is left
at the default value.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This resolves the conflict with:
drivers/usb/host/ehci-tegra.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The upcoming Intel Lynx Point chipset includes an xHCI host controller
that can have ports switched from the EHCI host controller, just like
the Intel Panther Point xHCI host. This time, ports from both EHCI
hosts can be switched to the xHCI host controller. The PCI config
registers to do the port switching are in the exact same place in the
xHCI PCI configuration registers, with the same semantics.
Hooray for shipping patches for next-gen hardware before the current gen
hardware is even available for purchase!
This patch should be backported to stable kernels as old as 3.0,
that contain commit 69e848c2090aebba5698a1620604c7dccb448684
"Intel xhci: Support EHCI/xHCI port switching."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
|
|
This patch (as1545) fixes a problem affecting several ASUS computers:
The machine crashes or corrupts memory when going into suspend if the
ehci-hcd driver is bound to any controllers. Users have been forced
to unbind or unload ehci-hcd before putting their systems to sleep.
After extensive testing, it was determined that the machines don't
like going into suspend when any EHCI controllers are in the PCI D3
power state. Presumably this is a firmware bug, but there's nothing
we can do about it except to avoid putting the controllers in D3
during system sleep.
The patch adds a new flag to indicate whether the problem is present,
and avoids changing the controller's power state if the flag is set.
Runtime suspend is unaffected; this matters only for system suspend.
However as a side effect, the controller will not respond to remote
wakeup requests while the system is asleep. Hence USB wakeup is not
functional -- but of course, this is already true in the current state
of affairs.
This fixes Bugzilla #42728.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Tested-by: Andrey Rahmatullin <wrar@wrar.name>
Tested-by: Oleksij Rempel (fishor) <bug-track@fisher-privat.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com>
Cc: Alan Cox <alan@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1489) works around a hardware bug in MosChip EHCI
controllers. Evidently when one of these controllers increments the
frame-index register, it changes the three low-order bits (the
microframe counter) before changing the higher order bits (the frame
counter). If the register is read at just the wrong time, the value
obtained is too low by 8.
When the appropriate quirk flag is set, we work around this problem by
reading the frame-index register a second time if the first value's
three low-order bits are all 0. This gives the hardware a chance to
finish updating the register, yielding the correct value.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Jason N Pitt <jpitt@fhcrc.org>
CC: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1483) improves the ehci-hcd driver family by getting rid
of the reliance on the hcd->state variable. It has no clear owner and
it isn't protected by the usual HCD locks. In its place, the patch
adds a new, private ehci->rh_state field to record the state of the
root hub.
Along the way, the patch removes a couple of lines containing
redundant assignments to the state variable. Also, the QUIESCING
state simply gets changed to the RUNNING state, because the driver
doesn't make any distinction between them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The Intel Panther Point chipsets contain an EHCI and xHCI host controller
that shares some number of skew-dependent ports. These ports can be
switched from the EHCI to the xHCI host (and vice versa) by a hardware MUX
that is controlled by registers in the xHCI PCI configuration space. The
USB 3.0 SuperSpeed terminations on the xHCI ports can be controlled
separately from the USB 2.0 data wires.
This switchover mechanism is there to support users who do a custom
install of certain non-Linux operating systems that don't have official
USB 3.0 support. By default, the ports are under EHCI, SuperSpeed
terminations are off, and USB 3.0 devices will show up under the EHCI
controller at reduced speeds. (This was more palatable for the marketing
folks than having completely dead USB 3.0 ports if no xHCI drivers are
available.) Users should be able to turn on xHCI by default through a
BIOS option, but users are happiest when they don't have to change random
BIOS settings.
This patch introduces a driver method to switchover the ports from EHCI to
xHCI before the EHCI driver finishes PCI enumeration. We want to switch
the ports over before the USB core has the chance to enumerate devices
under EHCI, or boot from USB mass storage will fail if the boot device
connects under EHCI first, and then gets disconnected when the port
switches over to xHCI.
Add code to the xHCI PCI quirk to switch the ports from EHCI to xHCI. The
PCI quirks code will run before any other PCI probe function is called, so
this avoids the issue with boot devices.
Another issue is with BIOS behavior during system resume from hibernate.
If the BIOS doesn't support xHCI, it may switch the devices under EHCI to
allow use of the USB keyboard, mice, and mass storage devices. It's
supposed to remember the value of the port routing registers and switch
them back when the OS attempts to take control of the xHCI host controller,
but we all know not to trust BIOS writers.
Make both the xHCI driver and the EHCI driver attempt to switchover the
ports in their PCI resume functions. We can't guarantee which PCI device
will be resumed first, so this avoids any race conditions. Writing a '1'
to an already set port switchover bit or a '0' to a cleared port switchover
bit should have no effect.
The xHCI PCI configuration registers will be documented in the EDS-level
chipset spec, which is not public yet. I have permission from legal and
the Intel chipset group to release this patch early to allow good Linux
support at product launch. I've tried to document the registers as much
as possible, so please let me know if anything is unclear.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
The two first HC capability registers (CAPLENGTH and HCIVERSION)
are defined as one 8-bit and one 16-bit register. Most HC
implementations have selected to treat these registers as part
of a 32-bit register, giving the same layout for both big and
small endian systems.
This patch adds a new quirk, big_endian_capbase, to support
controllers with big endian register interfaces that treat
HCIVERSION and CAPLENGTH as individual registers.
Signed-off-by: Jan Andersson <jan@gaisler.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch moves the AMD PLL quirk code in OHCI/EHCI driver to pci-quirks.c,
and exports the functions to be used by xHCI driver later.
AMD PLL quirk disable the optional PM feature inside specific
SB700/SB800/Hudson-2/3 platforms under the following conditions:
1. If an isochronous device is connected to OHCI/EHCI/xHCI port and is active;
2. Optional PM feature that powers down the internal Bus PLL when the link is
in low power state is enabled.
Without AMD PLL quirk, USB isochronous stream may stutter or have breaks
occasionally, which greatly impair the performance of audio/video streams.
Currently AMD PLL quirk is implemented in OHCI and EHCI driver, and will be
added to xHCI driver too. They are doing similar things actually, so move
the quirk code to pci-quirks.c, which has several advantages:
1. Remove duplicate defines and functions in OHCI/EHCI (and xHCI) driver and
make them cleaner;
2. AMD chipset information will be probed only once and then stored.
Currently they're probed during every OHCI/EHCI initialization, move
the detect code to pci-quirks.c saves the repeat detect cost;
3. Build up synchronization among OHCI/EHCI/xHCI driver. In current
code, every host controller enable/disable PLL only according to
its own status, and may enable PLL while there is still isoc transfer on
other HCs. Move the quirk to pci-quirks.c prevents this issue.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alex He <alex.he@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
There is a msleep with spin lock held during ehci pci suspend, which will
cause kernel BUG: scheduling while atomic. Fix that.
[ 184.139620] BUG: scheduling while atomic: kworker/u:11/416/0x00000002
[ 184.139632] 4 locks held by kworker/u:11/416:
[ 184.139640] #0: (events_unbound){+.+.+.}, at: [<c104ddd4>] process_one_work+0x1b3/0x4cb
[ 184.139669] #1: ((&entry->work)){+.+.+.}, at: [<c104ddd4>] process_one_work+0x1b3/0x4cb
[ 184.139686] #2: (&__lockdep_no_validate__){+.+.+.}, at: [<c127cde3>] __device_suspend+0x2c/0x154
[ 184.139706] #3: (&(&ehci->lock)->rlock){-.-...}, at: [<c132f3d8>] ehci_pci_suspend+0x35/0x7b
[ 184.139725] Modules linked in: serio_raw pegasus joydev mrst_gfx(C) battery
[ 184.139748] irq event stamp: 52
[ 184.139753] hardirqs last enabled at (51): [<c14fdaac>] mutex_lock_nested+0x258/0x293
[ 184.139766] hardirqs last disabled at (52): [<c14fe7b4>] _raw_spin_lock_irqsave+0xf/0x3e
[ 184.139777] softirqs last enabled at (0): [<c10371c1>] copy_process+0x3d2/0x109d
[ 184.139789] softirqs last disabled at (0): [< (null)>] (null)
[ 184.139802] Pid: 416, comm: kworker/u:11 Tainted: G C 2.6.37-6.3-adaptation-oaktrail #37
[ 184.139809] Call Trace:
[ 184.139820] [<c102eeff>] __schedule_bug+0x5e/0x65
[ 184.139829] [<c14fbca5>] schedule+0xac/0xc4c
[ 184.139840] [<c11d4845>] ? string+0x37/0x8b
[ 184.139853] [<c1044f21>] ? lock_timer_base+0x1f/0x3e
[ 184.139863] [<c14fe7da>] ? _raw_spin_lock_irqsave+0x35/0x3e
[ 184.139876] [<c1061590>] ? trace_hardirqs_off+0xb/0xd
[ 184.139885] [<c14fccdc>] schedule_timeout+0x283/0x2d9
[ 184.139896] [<c104516f>] ? process_timeout+0x0/0xa
[ 184.139906] [<c14fcd47>] schedule_timeout_uninterruptible+0x15/0x17
[ 184.139916] [<c104566a>] msleep+0x10/0x16
[ 184.139926] [<c132f316>] ehci_adjust_port_wakeup_flags+0x69/0xf6
[ 184.139937] [<c132f3eb>] ehci_pci_suspend+0x48/0x7b
[ 184.139946] [<c1326587>] suspend_common+0x52/0xbb
[ 184.139956] [<c1326625>] hcd_pci_suspend+0x26/0x28
[ 184.139967] [<c11e7182>] pci_pm_suspend+0x5f/0xd0
[ 184.139976] [<c127ca3a>] pm_op+0x5d/0xf0
[ 184.139986] [<c127ceac>] __device_suspend+0xf5/0x154
[ 184.139996] [<c127d2c8>] async_suspend+0x16/0x3a
[ 184.140006] [<c1058f54>] async_run_entry_fn+0x89/0x111
[ 184.140016] [<c104deb6>] process_one_work+0x295/0x4cb
[ 184.140026] [<c1058ecb>] ? async_run_entry_fn+0x0/0x111
[ 184.140036] [<c104e3d0>] worker_thread+0x17f/0x298
[ 184.140045] [<c104e251>] ? worker_thread+0x0/0x298
[ 184.140055] [<c105277f>] kthread+0x64/0x69
[ 184.140064] [<c105271b>] ? kthread+0x0/0x69
[ 184.140075] [<c1002efa>] kernel_thread_helper+0x6/0x1a
Signed-off-by: Yin Kangkai <kangkai.yin@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <dbrownell@users.sourceforge.net>
CC: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
AMD Hudson also needs the same ASPM quirk as SB800
Signed-off-by: Alex He <alex.he@amd.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
* usb-next: (132 commits)
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
usb: gadget: f_ncm.c added
usb: gadget: u_ether: prepare for NCM
usb: pch_udc: Fix setup transfers with data out
usb: pch_udc: Fix compile error, warnings and checkpatch warnings
usb: add ab8500 usb transceiver driver
USB: gadget: Implement runtime PM for MSM bus glue driver
USB: gadget: Implement runtime PM for ci13xxx gadget
USB: gadget: Add USB controller driver for MSM SoC
USB: gadget: Introduce ci13xxx_udc_driver struct
USB: gadget: Initialize ci13xxx gadget device's coherent DMA mask
USB: gadget: Fix "scheduling while atomic" bugs in ci13xxx_udc
USB: gadget: Separate out PCI bus code from ci13xxx_udc
...
|
|
When ASPM PM Feature is enabled on UMI link, devices that use ISOC stream of
data transfer may be exposed to longer latency causing less than optimal per-
formance of the device. The longer latencies are normal and are due to link
wake time coming out of low power state which happens frequently to save
power when the link is not active.
The following code will make exception for certain features of ASPM to be by
passed and keep the logic normal state only when the ISOC device is connected
and active. This change will allow the device to run at optimal performance
yet minimize the impact on overall power savings.
Signed-off-by: Alex He <alex.he@amd.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Tested on MacBookAir3,1. Without this, we get EPROTO errors when
fetching device config descriptors.
Signed-off-by: Brian Tarricone <brian@tarricone.org>
Reported-by: Benoit Gschwind <gschwind@gnu-log.net>
Tested-by: Edgar Hucek <gimli@dark-green.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch adds support for the EHCI IP block present on the Intel
CE4100.
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
CC: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
On AMD SB700/SB800/Hudson-2/3 platforms, USB EHCI controller may read/write
to memory space not allocated to USB controller if there is longer than
normal latency on DMA read encountered. In this condition the exposure will
be encountered only if the driver has following format of Periodic Frame
List link pointer structure:
For any idle periodic schedule, the Frame List link pointers that have the
T-bit set to 1 intending to terminate the use of frame list link pointer
as a physical memory pointer.
Idle periodic schedule Frame List Link pointer shoule be in the following
format to avoid the issue:
Frame list link pointer should be always contains a valid pointer to a
inactive QHead with T-bit set to 0.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
We have to do so due to HW limitation.
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1405) fixes a small bug in ehci-hcd's isochronous
scheduler. Not all EHCI controllers are PCI, and the code shouldn't
assume that they are. Instead, introduce a special flag for
controllers which need to delay iso scheduling for full-speed devices
beyond the scheduling threshold.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: David Brownell <david-b@pacbell.net>
CC: stable <stable@kernel.org>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
This patch (as1385) adds a "do_wakeup" parameter to the pci_suspend
method used by PCI-based host controller drivers. ehci-hcd in
particular needs to know whether or not to enable wakeup when
suspending a controller. Although that information is currently
available through device_may_wakeup(), when support is added for
runtime suspend this will no longer be true.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
With this patch, the LPM capable EHCI host controller can put device
into L1 sleep state which is a mode that can enter/exit quickly, and
reduce power consumption.
Signed-off-by: Jacob Pan <jacob.jun.pan@intel.com>
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1380) fixes a bug in the wakeup settings for EHCI host
controllers. When the controller is suspended, if it isn't enabled
for remote wakeup then we have to turn off all the port wakeup flags.
Disabling PCI PME# isn't good enough, because some systems (Intel)
evidently use alternate wakeup signalling paths.
In addition, the patch improves the handling of the Intel Moorestown
hardware by performing various power-up and power-down delays just
once instead of once for each port (i.e., the delays are moved outside
of the port loops). This requires extra code, but the total delay
time is reduced.
There are also a few additional minor cleanups.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Ondrej Zary <linux@rainbow-software.org>
CC: Alek Du <alek.du@intel.com>
CC: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
I've been running with this patch on my Niagara2 boxes for some time
and have not seen any ill effects yet. Maybe we can stash this into
the USB tree to get exposure for some time in -next and if anything
crops up we can simply revert?
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
a quirky chipset needs periodic schedules to run for a minimum
time before they can be disabled again. This enforces the requirement
with a time stamp and a calculated delay
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
If the EHCI debug port is initialized and in use, the EHCI host
controller driver must follow two rules.
1) If the EHCI host driver issues a controller reset, the debug
controller driver re-initialization must get called after the reset
is completed.
2) The EHCI host driver should ignore any requests to the physical
EHCI debug port when the EHCI debug port is in use.
The code to check for the debug port was moved from ehci_pci_reinit()
to ehci_pci_setup because it must get called prior to ehci_reset()
which will clear the debug port registers.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: dbrownell@users.sourceforge.net
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Basically the io watchdog is only useful for those quirk HCDs. For most
good ones, it only brings unnecessary wakeups. At least, I know the
Intel EHCI HCDs should turn off the flag.
Signed-off-by: Alek Du <alek.du@intel.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
trivial: fix typo "for for" in multiple files
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This patch (as1256) changes ehci-hcd and all the other drivers in the
EHCI family to make use of the new clear_tt_buffer callbacks. When a
Clear-TT-Buffer request is in progress for a QH, the QH is not allowed
to be linked into the async schedule until the request is finished.
At that time, if there are any URBs queued for the QH, it is linked
into the async schedule.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1245) fixes a bug in ehci-hcd. When an URB is queued
for an endpoint whose QH is already in the LINKED state, the QH
doesn't get refreshed. As a result, if usb_clear_halt() was called
during the time that the QH was linked but idle, the data toggle value
in the QH doesn't get reset.
The symptom is that after a clear_halt, data gets lost and transfers
time out. This problem is starting to show up now because the
"ehci-hcd unlink speedups" patch causes QHs with no queued URBs to
remain linked for a suitable time.
The patch utilizes the new endpoint_reset mechanism to fix the
problem. When an endpoint is reset, the new method forcibly unlinks
the QH (if necessary) and safely updates the toggle value. This
allows qh_update() to be simplified and avoids using usb_device's
toggle bits in a rather unintuitive way.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Tested-by: David <david@unsolicited.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1237) changes the way the PCI host controller drivers
avoid retaining bogus hardware states during resume-from-hibernation.
Previously we had reset the hardware as part of preparing to reinstate
the memory image. But we can do better now with the new PM framework,
since we know exactly which resume operations are from hibernation.
The pci_resume method is changed to accept a flag indicating whether
the system is resuming from hibernation. When this flag is set, the
drivers will reset the hardware to get rid of any existing state.
Similarly, the pci_suspend method is changed to remove the
pm_message_t argument. It's no longer needed, since no special action
has to be taken when preparing to reinstate the memory image.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1236) converts the USB PCI power management routines
over to the new PM framework.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Replace all DMA_31BIT_MASK macro with DMA_BIT_MASK(31)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If a USB PCI controller is behind a cardbus bridge, we are trying to
restore its configuration registers too early, before the cardbus
bridge is operational. To fix this, call pci_restore_state() from
usb_hcd_pci_resume() and remove usb_hcd_pci_resume_early() which is
no longer necessary (the configuration spaces of USB controllers that
are not behind cardbus bridges will be restored by the PCI PM core
with interrupts disabled anyway).
This patch fixes the regression from 2.6.28 tracked as
http://bugzilla.kernel.org/show_bug.cgi?id=12659
[ Side note: the proper long-term fix is probably to just force the
unplug event at suspend time instead of doing a plug/unplug at resume
time, but this patch is fine regardless - Linus ]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit a0d4922da2e4ccb0973095d8d29f36f6b1b5f703
(USB: fix up suspend and resume for PCI host controllers) attempted
to fix the suspend-resume of PCI USB controllers, but unfortunately
it did that incorrectly and interrupts are left enabled by the USB
controllers' ->suspend_late() callback as a result. This leads to
serious problems during suspend which are very difficult to debug.
Fix the issue by removing the ->suspend_late() callback of PCI
USB controllers and moving the code from there to the ->suspend()
callback executed with interrupts enabled. Additionally, make
the ->resume() callback of PCI USB controllers execute
pci_enable_wake(dev, PCI_D0, false) to disable wake-up from the
full power state (PCI_D0).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Andrey Borzenkov <arvidjaar@mail.ru>
Tested-by: "Jeff Chua" <jeff.chua.linux@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: "Zdenek Kabelac" <zdenek.kabelac@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1199) changes the initial wakeup settings for PCI USB
host controllers. The controllers are marked as capable of waking the
system, but wakeup is not enabled by default.
It turns out that enabling wakeup for USB host controllers has a lot
of bad consequences. As the simplest example, if a USB mouse or
keyboard is unplugged immediately after the computer is put to sleep,
the unplug will cause the system to wake back up again! We are better
off marking them as wakeup-capable and leaving wakeup disabled.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Rafael J. Wysocki <rjw@sisk.pl>
CC: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1193b) enables wakeup during initialization for all PCI
host controllers, and it removes some code (and comments!) that are no
longer needed now that the PCI core automatically initializes wakeup
settings for all new devices.
The idea is that the bus should initialize wakeup, and the bus glue
or controller driver should enable it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1192) rearranges the USB PCI host controller suspend and
resume and resume routines:
Use pci_wake_from_d3() for enabling and disabling wakeup,
instead of pci_enable_wake().
Carry out the actual state change while interrupts are
disabled.
Change the order of the preparations to agree with the
general recommendation for PCI devices, instead of
messing around with the wakeup settings while the device
is in D3.
In .suspend:
Call the underlying driver to disable IRQ
generation;
pci_wake_from_d3(device_may_wakeup());
pci_disable_device();
In .suspend_late:
pci_save_state();
pci_set_power_state(D3hot);
(for PPC_PMAC) Disable ASIC clocks
In .resume_early:
(for PPC_PMAC) Enable ASIC clocks
pci_set_power_state(D0);
pci_restore_state();
In .resume:
pci_enable_device();
pci_set_master();
pci_wake_from_d3(0);
Call the underlying driver to reenable IRQ
generation
Add the necessary .suspend_late and .resume_early method
pointers to the PCI host controller drivers.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch is required for all AMD SB600 revisions to avoid USB subsystem hang
symptom. The USB subsystem hang symptom is observed when the system has
multiple USB devices connected to it. In some cases a USB hub may be required
to observe this symptom.
Reported in bugzilla as #11599, the similar patch for SB700 old revision is:
commit b09bc6cbae4dd3a2d35722668ef2c502a7b8b093
Reported-by: raffaele <ralfconn@tele2.it>
Tested-by: Roman Mamedov <roman@rm.pp.ru>
Signed-off-by: Shane Huang <shane.huang@amd.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch is required for AMD SB700 south bridge revision A12 and A13 to avoid
USB subsystem hang symptom. The USB subsystem hang symptom is observed when the
system has multiple USB devices connected to it. In some cases a USB hub may be
required to observe this symptom.
This patch works around the problem by correcting the internal register setting
that will help by changing the behavior of the internal logic to avoid the
USB subsystem hang issue. The change in the behavior of the logic does not
impact the normal operation of the USB subsystem.
Reported-by: Volker Armin Hemmann <volker.armin.hemmann@tu-clausthal.de>
Tested-by: Volker Armin Hemmann <volker.armin.hemmann@tu-clausthal.de>
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Libin Yang <libin.yang@amd.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1096) fixes an annoying problem: When a full-speed or
low-speed device is plugged into an EHCI controller, it fails to
enumerate at high speed and then is handed over to the companion
controller. But usbcore logs a misleading and unwanted error message
when the high-speed enumeration fails.
The patch adds a new HCD method, port_handed_over, which asks whether
a port has been handed over to a companion controller. If it has, the
error message is suppressed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1095) cleans up the HCD glue and several of the EHCI
bus-glue files. The ehci->is_tdi_rh_tt flag is redundant, since it
means the same thing as the hcd->has_tt flag, so it is removed and the
other flag used in its place.
Some of the bus-glue files didn't get the relinquish_port method added
to their hc_driver structures. Although that routine currently
doesn't do anything for controllers with an integrated TT, in the
future it might. So the patch adds it where it is missing.
Lastly, some of the bus-glue files have erroneous entries for their
hc_driver's suspend and resume methods. These method pointers are
specific to PCI and shouldn't be used otherwise.
(The patch also includes an invisible whitespace fix.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
This patch (as1072) fixes some recently-introduced compile problems
that show up in ehci-hcd when CONFIG_PM is turned off.
PORT_WAKE_BITS needs to be defined always.
ehci_port_power() is called during initialization by all the
EHCI variants other than the PCI version, in which it is
"defined but not used". So add a call to it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
When a USB device is suspended, whether or not it is enabled for
remote wakeup depends on the device_may_wakeup() setting. The setting
is then saved in the do_remote_wakeup flag.
Later on, however, the device_may_wakeup() value can change because of
user activity. So when testing whether a suspended device is or
should be enabled for remote wakeup, we should always test
do_remote_wakeup instead of device_may_wakeup(). This patch (as1076)
makes that change for root hubs in several places.
The patch also adjusts uhci-hcd so that when an autostopped controller
is suspended, the remote wakeup setting agrees with the value recorded
in the root hub's do_remote_wakeup flag.
And the patch adjusts ehci-hcd so that wakeup events on selectively
suspended ports (i.e., the bus itself isn't suspended) don't turn on
the PME# wakeup signal.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The .suspend and .resume method pointers in struct usb_hcd have not
been fully understood by host-controller driver writers. They are
meant for use with PCI controllers; other platform-specific drivers
generally should not refer to them.
To try and clarify matters, this patch (as1065) renames those methods
to .pci_suspend and .pci_resume. It eliminates corresponding dead code
and bogus references in the ohci-ssb and u132-hcd drivers.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Currently EHCI root hubs enumerate with a bDeviceProtocol code
indicating that they possess a Transaction Translator. However the
vast majority of controllers do not; they rely on a companion
controller to handle full- and low-speed communications. This patch
(as1064) changes the root-hub device descriptor to match the actual
situation.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
