summaryrefslogtreecommitdiffstats
path: root/drivers/usb/host/ohci.h
AgeCommit message (Collapse)Author
2014-11-03USB: OHCI: Eliminate platform-specific test in ohci.hKevin Cernekee
The bcm63xx and bcm3384 platforms need to set OHCI_QUIRK_FRAME_NO, but they are non-PPC platforms and don't enable CONFIG_PPC_MPC52xx. Therefore this patch changes the code that uses OHCI_QUIRK_FRAME_NO, making it not depend on CONFIG_PPC_MPC52xx. Also, rephrase the comments describing OHCI_QUIRK_FRAME_NO and the related PSW endian swap. Signed-off-by: Kevin Cernekee <cernekee@gmail.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-18USB: OHCI: add check for stopped frame counterAlan Stern
This patch adds an extra check to ohci-hcd's I/O watchdog routine. If the controller stops updating the frame counter, we will assume it is dead. But there has to be an exception: Some controllers stop the frame counter when no ports are connected. Check to make sure there is at least one active port before deciding the controller is dead. (This test may appear racy, but it isn't. Enabling a newly connected port takes several milliseconds, during which time the frame counter must advance.) Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Dennis New <dennisn@dennisn.linuxd.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-18USB: OHCI: add I/O watchdog for orphan TDsAlan Stern
Some OHCI controllers have a bug: They fail to add completed TDs to the done queue. Examining this queue is the only method ohci-hcd has for telling when a transfer is complete; failure to add a TD can result in an URB that never completes and cannot be unlinked. This patch adds a watchdog routine to ohci-hcd. The routine periodically scans the active ED and TD lists, looking for TDs which are finished but not on the done queue. When one is found, and it is certain that the controller hardware will never add the TD to the done queue, the watchdog routine manually puts the TD on the done list so that it can be handled normally. The watchdog routine also checks for a condition indicating the controller has died. If the done queue is non-empty but the HccaDoneHead pointer hasn't been updated for a few hundred milliseconds, we assume the controller will never update it and therefore is dead. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-18USB: OHCI: make URB completions single-threadedAlan Stern
URBs for a particular endpoint should complete sequentially. That is, we shouldn't call the completion handler for one URB until the handler for the previous URB has returned. When the OHCI watchdog routine is added, there will be two paths for completing URBs: interrupt handler and watchdog routine. Their activities have to be synchronized so that completions don't occur in multiple threads concurrently. For that purpose, this patch creates an ohci_work() routine which will be responsible for calling process_done_list() and finish_unlinks(), the two routines that detect when an URB is complete. Everything will funnel through ohci_work(), and it will be careful not to run in more than one thread at a time. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-18USB: OHCI: redesign the TD done listAlan Stern
This patch changes the way ohci-hcd handles the TD done list. In addition to relying on the TD pointers stored by the controller hardware, we need to handle TDs that the hardware has forgotten about. This means the list has to exist even while the dl_done_list() routine isn't running. That function essentially gets split in two: update_done_list() reads the TD pointers stored by the hardware and adds the TDs to the done list, and process_done_list() scans through the list to handle URB completions. When we detect a TD that the hardware forgot about, we will be able to add it to the done list manually and then process it normally. Since the list is really a queue, and because there can be a lot of TDs, keep the existing singly linked implementation. To insure that URBs are given back in order of submission, whenever a TD is added to the done list, all the preceding TDs for the same endpoint must be added as well (going back to the first one that isn't already on the done list). The done list manipulations must all be protected by the private lock. The scope of the lock is expanded in preparation for the watchdog routine to be added in a later patch. We have to be more careful about giving back unlinked URBs. Since TDs may be added to the done list by the watchdog routine and not in response to a controller interrupt, we have to check explicitly to make sure all the URB's TDs that were added to the done list have been processed before giving back the URB. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-18USB: OHCI: revert the ZF Micro orphan-TD quirkAlan Stern
This patch reverts the important parts of commit 89a0fd18a96e (USB: OHCI handles more ZFMicro quirks), namely, the parts related to handling orphan TDs for interrupt endpoints. A later patch in this series will introduce a more general mechanism that applies to all endpoint types and all controllers. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-20Merge 3.15-rc5 into usb-nextGreg Kroah-Hartman
We need these USB fixes in here as well. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-03USB: OHCI: fix problem with global suspend on ATI controllersAlan Stern
Some OHCI controllers from ATI/AMD seem to have difficulty with "global" USB suspend, that is, suspending an entire USB bus without setting the suspend feature for each port connected to a device. When we try to resume the child devices, the controller gives timeout errors on the unsuspended ports, requiring resets, and can even cause ohci-hcd to hang; see http://marc.info/?l=linux-usb&m=139514332820398&w=2 and the following messages. This patch fixes the problem by adding a new quirk flag to ohci-hcd. The flag causes the ohci_rh_suspend() routine to suspend each unsuspended, enabled port before suspending the root hub. This effectively converts the "global" suspend to an ordinary root-hub suspend. There is no need to unsuspend these ports when the root hub is resumed, because the child devices will be resumed anyway in the course of a normal system resume ("global" suspend is never used for runtime PM). This patch should be applied to all stable kernels which include commit 0aa2832dd0d9 (USB: use "global suspend" for system sleep on USB-2 buses) or a backported version thereof. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Peter Münster <pmlists@free.fr> Tested-by: Peter Münster <pmlists@free.fr> CC: <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-04-24USB: OHCI: Export the OHCI hub control and status_data functionsLaurent Pinchart
Platform drivers sometimes need to perform specific handling of hub control requests and status data. Make this possible by exporting the ohci_hub_control() and ohci_hub_status_data() functions which can then be called from custom hub operations in the default case. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-03ohci: kill ohci_vdbgOliver Neukum
With the introduction of dynamic debugging it has become redundant. Collapse it with ohci_dbg() Signed-off-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-03ohci: remove conditional compilationOliver Neukum
Conditional compilation for debugging is removed in favor of dynamic debugging. To do so 1. the support for debugfs is always compiled 2. the support for the ancient print_urb debugging aid is removed Signed-off-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-03USB: OHCI: add a name for the platform-private fieldManjunath Goudar
This patch adds an ohci->priv field for private use by OHCI platform drivers. Until now none of the platform drivers has used this private space, but that's about to change in the next patch of this series. Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-05-30USB: OHCI: prepare to make ohci-hcd a library moduleManjunath Goudar
This patch prepares ohci-hcd for being split up into a core library and separate platform driver modules. A generic ohci_hc_driver structure is created, containing all the "standard" values, and a new mechanism is added whereby a driver module can specify a set of overrides to those values. In addition the ohci_restart(),ohci_suspend() and ohci_resume() routines need to be EXPORTed for use by the drivers. Added ohci_setip(() and ohci_start() routine for to start the generic controller rather than each having its own idiosyncratic approach. This allow to clean duplicated code in most of SOC driver In V2: -ohci_hcd_init() ohci_run() and ohci_stop() are not made non-static. -Adds the ohci_setup() and ohci_start() routine. In V3: -purpose of ohci_setup() and ohci_start() function description written in the patch description. -ohci_init() are not made non-static but now called beginning of the ohci_restart(). -ohci_run() signature change reverted back. -unrelated changes removed. -duplicate comment line removed. -inline ohci_suspend() and ohci_resume() is not needed so removed from ohci.h file. In V4: -ohci-init() EXPORTed because it is called by all bus glue modules. -ohci-setup() removed from 1/2 added into 2/2 patch. In V5: -Again ohci_setup() is added and EXPORTed because to replace the ohci_init() from all bus glues. -ohci_init() is not made non-static function. In V6: -ohci_init() call is removed from ohci_quirk_nec_worker(), because it is already called in ohci_restart(). In V8: -ohci_hcd_init() is called by ohci_setup() to make generic ohci initialization in all ohci drivers. Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-06-13USB: move transceiver from ehci_hcd and ohci_hcd to hcd and rename it as phyRichard Zhao
- to decrease redundant since both ehci_hcd and ohci_hcd have the same variable - it helps access phy in usb core code - phy is more meaningful than transceiver Signed-off-by: Richard Zhao <richard.zhao@freescale.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-13usb: otg: Rename otg_transceiver to usb_phyHeikki Krogerus
This is the first step in separating USB transceivers from USB OTG utilities. Includes fixes to IMX code from Sascha Hauer. Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Pavankumar Kondeti <pkondeti@codeaurora.org> Acked-by: Li Yang <leoli@freescale.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Reviewed-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-11-26Merge 3.2-rc3 into usb-linusGreg Kroah-Hartman
This pulls in the latest USB bugfixes and helps a few of the drivers merge nicer in the future due to changes in both branches. Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-11-18OHCI: final fix for NVIDIA problems (I hope)Alan Stern
Problems with NVIDIA's OHCI host controllers persist. After looking carefully through the spec, I finally realized that when a controller is reset it then automatically goes into a SUSPEND state in which it is completely quiescent (no DMA and no IRQs) and from which it will not awaken until the system puts it into the OPERATIONAL state. Therefore there's no need to worry about controllers being in the RESET state for extended periods, or remaining in the OPERATIONAL state during system shutdown. The proper action for device initialization is to put the controller into the RESET state (if it's not there already) and then to issue a software reset. Similarly, the proper action for device shutdown is simply to do a software reset. This patch (as1499) implements such an approach. It simplifies initialization and shutdown, and allows the NVIDIA shutdown-quirk code to be removed. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Andre "Osku" Schmidt <andre.osku.schmidt@googlemail.com> Tested-by: Arno Augustin <Arno.Augustin@web.de> Cc: stable <stable@vger.kernel.org> [after tested in 3.2 for a while] Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-11-18OHCI: remove uses of hcd->stateAlan Stern
This patch (as1500) removes all uses of the objectionable hcd->state variable from the ohci-hcd family of drivers. It is replaced by a private ohci->rh_state field, just as in uhci-hcd and ehci-hcd. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-03-16Merge branch 'remove' of master.kernel.org:/home/rmk/linux-2.6-armLinus Torvalds
* 'remove' of master.kernel.org:/home/rmk/linux-2.6-arm: ARM: 6629/2: aaec2000: remove support for mach-aaec2000 ARM: lh7a40x: remove unmaintained platform support Fix up trivial conflicts in - arch/arm/mach-{aaec2000,lh7a40x}/include/mach/memory.h (removed) - drivers/usb/gadget/Kconfig (USB_[GADGET_]LH7A40X removed, others added)
2011-03-01USB host: Move AMD PLL quirk to pci-quirks.cAndiry Xu
This patch moves the AMD PLL quirk code in OHCI/EHCI driver to pci-quirks.c, and exports the functions to be used by xHCI driver later. AMD PLL quirk disable the optional PM feature inside specific SB700/SB800/Hudson-2/3 platforms under the following conditions: 1. If an isochronous device is connected to OHCI/EHCI/xHCI port and is active; 2. Optional PM feature that powers down the internal Bus PLL when the link is in low power state is enabled. Without AMD PLL quirk, USB isochronous stream may stutter or have breaks occasionally, which greatly impair the performance of audio/video streams. Currently AMD PLL quirk is implemented in OHCI and EHCI driver, and will be added to xHCI driver too. They are doing similar things actually, so move the quirk code to pci-quirks.c, which has several advantages: 1. Remove duplicate defines and functions in OHCI/EHCI (and xHCI) driver and make them cleaner; 2. AMD chipset information will be probed only once and then stored. Currently they're probed during every OHCI/EHCI initialization, move the detect code to pci-quirks.c saves the repeat detect cost; 3. Build up synchronization among OHCI/EHCI/xHCI driver. In current code, every host controller enable/disable PLL only according to its own status, and may enable PLL while there is still isoc transfer on other HCs. Move the quirk to pci-quirks.c prevents this issue. Signed-off-by: Andiry Xu <andiry.xu@amd.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Alex He <alex.he@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-02-17Revert "USB host: Move AMD PLL quirk to pci-quirks.c"Greg Kroah-Hartman
This reverts commit b7d5b439b7a40dd0a0202fe1c118615a3fcc3b25. It conflicts with commit baab93afc2844b68d57b0dcca5e1d34c5d7cf411 "USB: EHCI: ASPM quirk of ISOC on AMD Hudson" and merging the two just doesn't work properly. Cc: Andiry Xu <andiry.xu@amd.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Alex He <alex.he@amd.com> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-02-04USB host: Move AMD PLL quirk to pci-quirks.cAndiry Xu
This patch moves the AMD PLL quirk code in OHCI/EHCI driver to pci-quirks.c, and exports the functions to be used by xHCI driver later. AMD PLL quirk disable the optional PM feature inside specific SB700/SB800/Hudson-2/3 platforms under the following conditions: 1. If an isochronous device is connected to OHCI/EHCI/xHCI port and is active; 2. Optional PM feature that powers down the internal Bus PLL when the link is in low power state is enabled. Without AMD PLL quirk, USB isochronous stream may stutter or have breaks occasionally, which greatly impair the performance of audio/video streams. Currently AMD PLL quirk is implemented in OHCI and EHCI driver, and will be added to xHCI driver too. They are doing similar things actually, so move the quirk code to pci-quirks.c, which has several advantages: 1. Remove duplicate defines and functions in OHCI/EHCI (and xHCI) driver and make them cleaner; 2. AMD chipset information will be probed only once and then stored. Currently they're probed during every OHCI/EHCI initialization, move the detect code to pci-quirks.c saves the repeat detect cost; 3. Build up synchronization among OHCI/EHCI/xHCI driver. In current code, every host controller enable/disable PLL only according to its own status, and may enable PLL while there is still isoc transfer on other HCs. Move the quirk to pci-quirks.c prevents this issue. Signed-off-by: Andiry Xu <andiry.xu@amd.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Alex He <alex.he@amd.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-01-24ARM: lh7a40x: remove unmaintained platform supportRussell King
lh7a40x has only been receiving updates for updates to generic code. The last involvement from the maintainer according to the git logs was in 2006. As such, it is a maintainence burden with no benefit. This gets rid of two defconfigs. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-10-22OHCI: work around for nVidia shutdown problemAlan Stern
This patch (as1417) fixes a problem affecting some (or all) nVidia chipsets. When the computer is shut down, the OHCI controllers continue to power the USB buses and evidently they drive a Reset signal out all their ports. This prevents attached devices from going to low power. Mouse LEDs stay on, for example, which is disconcerting for users and a drain on laptop batteries. The fix involves leaving each OHCI controller in the OPERATIONAL state during system shutdown rather than putting it in the RESET state. Although this nominally means the controller is running, in fact it's not doing very much since all the schedules are all disabled. However there is ongoing DMA to the Host Controller Communications Area, so the patch also disables the bus-master capability of all PCI USB controllers after the shutdown routine runs. The fix is applied only to nVidia-based PCI OHCI controllers, so it shouldn't cause problems on systems using other hardware. As an added safety measure, in case the kernel encounters one of these running controllers during boot, the patch changes quirk_usb_handoff_ohci() (which runs early on during PCI discovery) to reset the controller before anything bad can happen. Reported-by: Pali Rohár <pali.rohar@gmail.com> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: David Brownell <david-b@pacbell.net> Tested-by: Pali Rohár <pali.rohar@gmail.com> CC: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-11-17USB: ohci: quirk AMD prefetch for USB 1.1 ISO transferLibin Yang
The following patch in the driver is required to avoid USB 1.1 device failures that may occur due to requests from USB OHCI controllers may be overwritten if the latency for any pending request by the USB controller is very long (in the range of milliseconds). Signed-off-by: Libin Yang <libin.yang@amd.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-10-17usb: remove code associated with !CONFIG_PPC_MERGEKumar Gala
Now that arch/ppc is gone we don't need CONFIG_PPC_MERGE anymore remove the dead code associated with !CONFIG_PPC_MERGE. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-08-13USB: quirk PLL power down modeLibin Yang
On some AMD 700 series southbridges, ISO OUT transfers (such as audio playback through speakers) on the USB OHCI controller may be corrupted when an A-Link express power saving feature is active. PLL power down mode in conjunction with link power management feature L1 being enabled is the bad combination ... this patch prevents them from being enabled when ISO transfers are pending. Signed-off-by: Crane Cai <crane.cai@amd.com> Signed-off-by: Libin Yang <libin.yang@amd.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-08-13USB: Hook start_hnp into ohci structDmitry Baryshkov
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-08-13USB: ohci: make distrust_firmware a quirkDmitry Baryshkov
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-02-01USB: convert ohci debug files to use debugfs instead of sysfsTony Jones
We should not have multiple line files in sysfs, this moves the data to debugfs instead, like the UHCI driver. Signed-off-by: Tony Jones <tonyj@suse.de> Cc: Kay Sievers <kay.sievers@vrfy.org> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-10-12USB: add runtime frame_no quirk for big-endian OHCIValentine Barshak
Add OHCI big endian frame_no quirk. The frame_no value stored in the HCCA is a 16 bit field at a specific offset, but since not all CPUs can do 16-bit memory accesses it's used as a 32 bit field. And that's why big-endian OHCI must shift 16 bits ... unless the spec is not followed. Currently there's one MPC52xx platform that doesn't need the shift. This patch adds a new "big endian frame_no" quirk to control that at runtime. Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com> Acked-by: Dale Farnsworth <dale@farnsworth.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-10-12USB: OHCI handles more ZFMicro quirksMike Nuss
The ZF Micro OHCI controller exhibits unexpected behavior that seems to be related to high load. Under certain conditions, the controller will complete a TD, remove it from the endpoint's queue, and fail to add it to the donelist. This causes the endpoint to appear to stop responding. Worse, if the device is removed while in that state, OHCI will hang while waiting for the orphaned TD to complete. The situation is not recoverable without rebooting. This fix enhances the scope of the existing OHCI_QUIRK_ZFMICRO flag: 1. A watchdog routine periodically scans the OHCI structures to check for orphaned TDs. In these cases the TD is taken back from the controller and completed normally. 2. If a device is removed while the endpoint is hung but before the watchdog catches the situation, any outstanding TDs are taken back from the controller in the 'sanitize' phase. The ohci-hcd driver used to print "INTR_SF lossage" in this situation; this changes it to the universally accurate "ED unlink timeout". Other instances of this message presumably have different root causes. Both this Compaq quirk and a NEC quirk are now properly compiled out for non-PCI builds of this driver. Signed-off-by: Mike Nuss <mike@terascala.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-07-12USB: Fix NEC OHCI chip silicon bugMichael Hanselmann
This patch fixes a silicon bug in some NEC OHCI chips. The bug appears at random times and is very, very difficult to reproduce. Without the following patch, Linux would shut the chip and its associated devices down. In Apple PowerBooks this leads to an unusable keyboard and mouse (SSH still working). The idea of restarting the chip is taken from public Darwin code. Signed-off-by: Michael Hanselmann <linux-kernel@hansmi.ch> Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-09[PATCH] hci_{read,write}l() does force casts to wrong type for no reasonAl Viro
readl() et.al. expect iomem pointer, so WTF force-cast it to normal one??? Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-07USB: Fix OHCI warningBenjamin Herrenschmidt
This patch fixes a warning introduces by the split endian OHCI support patch on platforms that don't have readl_be/writel_be variants (though mostly harmless as those are called in an if (0) statement, but gcc still warns). Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-07USB: Implement support for "split" endian OHCIBenjamin Herrenschmidt
This patch separates support for big endian MMIO register access and big endian descriptors in order to support the Toshiba SCC implementation which has big endian registers but little endian in-memory descriptors. It simplifies the access functions a bit in ohci.h while at it. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Geoff Levand <geoffrey.levand@am.sony.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-20USB: ohci whitespace/comment fixupsDavid Brownell
This is an OHCI cleanup patch ... it removes a lot of erroneous whitespace (space before tab, at end of line) as well as the obsolete inline changelog. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-20USB: fix ohci.h over-use warningsJeff Garzik
When u132-hcd is built, it includes local header ohci.h, which appears to have been intended only for use by ohci-hcd. This throws warnings about functions which are defined and not used. The warnings thrown are because three small functions are implemented in the header, but not declared 'inline', a rather strange affair. Since these functions are small, let's go ahead and define them as 'inline', just like the inline functions surrounding them. This makes things more consistent, and kills the warnings. Signed-off-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-09-28OHCI: add auto-stop supportAlan Stern
This patch (as790b) adds "autostop" support to ohci-hcd: the driver will automatically stop the host controller when no devices have been connected for at least one second. This feature is useful when the USB autosuspend facility isn't available, such as when CONFIG_USB_SUSPEND hasn't been set. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-09-27USB: Dealias -110 code (more complete)Pete Zaitcev
The purpose of this patch is to split off the case when a device does not reply on the lower level (which is reported by HC hardware), and a case when the device accepted the request, but does not reply at upper level. This redefinition allows to diagnose issues easier, without asking the user if the -110 happened "immediately". The usbmon splits such cases already thanks to its timestamp, but it's not always available. I adjusted all drivers which I found affected (by searching for "urb"). Out of tree drivers may suffer a little bit, but I do not expect much breakage. At worst they may print a few messages. Signed-off-by: Pete Zaitcev <zaitcev@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-09-27USB: Properly unregister reboot notifier in case of failure in ehci hcdAleksey Gorelov
If some problem occurs during ehci startup, for instance, request_irq fails, echi hcd driver tries it best to cleanup, but fails to unregister reboot notifier, which in turn leads to crash on reboot/poweroff. The following patch resolves this problem by not using reboot notifiers anymore, but instead making ehci/ohci driver get its own shutdown method. For PCI, it is done through pci glue, for everything else through platform driver glue. One downside: sa1111 does not use platform driver stuff, and does not have its own shutdown hook, so no 'shutdown' is called for it now. I'm not sure if it is really necessary on that platform, though. Signed-off-by: Aleks Gorelov <dared1st@yahoo.com> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-10-28[PATCH] OHCI PM updatesDavid Brownell
This simplifies the OHCI root hub suspend logic: - Uses new usbcore root hub calls to make autosuspend work again: * Uses a newish usbcore root hub wakeup mechanism, making requests to khubd not keventd. * Uses an even newer sibling suspend hook. - Expect someone always made usbcore call ohci_hub_suspend() before bus glue fires; and that ohci_hub_resume() is only called after that bus glue ran. Previously, only CONFIG_USB_SUSPEND promised those things. (Includes updates to PCI and OMAP bus glue.) - Handle a not-noticed-before special case during resume from one of the swsusp snapshots when using "usb-handoff": the controller isn't left in RESET state. (A bug to fix in the usb-handoff code...) Also cleans up a minor debug printk glitch, and switches an mdelay over to an msleep (how did that stick around for so long?). Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> drivers/usb/host/ohci-dbg.c | 4 ---- drivers/usb/host/ohci-hcd.c | 2 +- drivers/usb/host/ohci-hub.c | 42 ++++++++++++------------------------------ drivers/usb/host/ohci-mem.c | 1 - drivers/usb/host/ohci-omap.c | 36 ++++++++++++------------------------ drivers/usb/host/ohci-pci.c | 40 ++++++++-------------------------------- drivers/usb/host/ohci.h | 1 - 7 files changed, 33 insertions(+), 93 deletions(-)
2005-09-12[PATCH] USB: OHCI relies less on NDP registerDavid Brownell
Some OHCI implementations have differences in the way the NDP register (in roothub_a) reports the number of ports present. This patch allows the platform specific code to optionally supply the number of ports. The driver just reads the value at init (if not supplied) instead of reading it every time its needed (except for an AMD756 bug workaround). It also sets the value correctly for the ARM pxa27x architecture. Signed-Off-By: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-06-27[PATCH] ohci-omap, sl811, dummy: remove hub_set_power_budgetAlan Stern
This patch changes the HCDs that used the old hub_set_power_budget call, making them use the new hcd->power_budget field instead. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-06-27[PATCH] USB: add reboot notifier to ohciDavid Brownell
Adds a reboot notifier to OHCI, mostly to benefit kexec; plus minor #include tweaks. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-04-18[PATCH] USB: OHCI on Compaq Aramada 7400David Brownell
This adds a quirk to the OHCI driver that lets it work with an old Compaq implementation. It also removes some needless strings from the non-debug version of the driver. Signed-off-by: Chris Clayton <chris_clayton@f1internet.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-04-16Linux-2.6.12-rc2v2.6.12-rc2Linus Torvalds
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!