summaryrefslogtreecommitdiffstats
path: root/drivers/usb/host/xhci.c
AgeCommit message (Collapse)Author
2011-03-13xhci: Refactor bus suspend state into a struct.Sarah Sharp
There are several variables in the xhci_hcd structure that are related to bus suspend and resume state. There are a couple different port status arrays that are accessed by port index. Move those variables into a separate structure, xhci_bus_state. Stash that structure in xhci_hcd. When we have two roothhubs that can be suspended and resumed separately, we can have two xhci_bus_states, and index into the port arrays in each structure with the fake roothub port index (not the real hardware port index). Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2011-03-13xhci: Always use usb_hcd in URB instead of converting xhci_hcd.Sarah Sharp
Make sure to call into the USB core's link, unlink, and giveback URB functions with the usb_hcd pointer found by using urb->dev->bus. This will avoid confusion later, when the xHCI driver will deal with URBs from two separate buses (the USB 3.0 roothub and the faked USB 2.0 roothub). Assume xhci_urb_dequeue() will be called with the proper usb_hcd. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2011-03-13xhci: Remove references to HC_STATE_RUNNING.Sarah Sharp
The USB core will set hcd->state to HC_STATE_RUNNING before calling xhci_run, so there's no point in setting it twice. The USB core also doesn't pay attention to HC_STATE_RUNNING on the resume path anymore; it uses HCD_RH_RUNNING(), which looks at hcd->flags & (1U << HCD_FLAG_RH_RUNNING. Therefore, it's safe to remove the state set in xhci_bus_resume(). Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2011-03-13xhci: Remove references to HC_STATE_HALT.Sarah Sharp
The xHCI driver doesn't ever test hcd->state for HC_STATE_HALT. The USB core recently stopped using it internally, so there's no point in setting it in the driver. We still need to set HC_STATE_RUNNING in order to make it past the USB core's hcd->state check in register_roothub(). Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2011-03-13xHCI: prolong host controller halt time limitAndiry Xu
xHCI 1.0 spec specifies the xHC shall halt within 16ms after software clears Run/Stop bit. In xHCI 0.96 spec the time limit is 16 microframes (2ms), it's too short and often cause dmesg shows "Host controller not halted, aborting reset." message when rmmod xhci-hcd. Modify the time limit to comply with xHCI 1.0 specification and prevents the warning message showing when remove xhci-hcd. Signed-off-by: Andiry Xu <andiry.xu@amd.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2011-03-13xHCI: Remove redundant variable in xhci_resume()Andiry Xu
Set hcd->state = HC_STATE_SUSPENDED if there is a power loss during system resume or the system is hibernated, otherwise leave it be. The variable old_state is redundant and made an unreachable code path, so remove it. Signed-off-by: Andiry Xu <andiry.xu@amd.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2011-03-13xhci: Remove old no-op test.Sarah Sharp
The test of placing a number of command no-ops on the command ring and counting the number of no-op events that were generated was only used during the initial xHCI driver bring up. This test is no longer used, so delete it. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2011-02-22USB: xhci: mark local functions as staticDmitry Torokhov
Functions that are not used outsde of the module they are defined should be marked as static. Signed-off-by: Dmitry Torokhov <dtor@vmware.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2011-02-20USB: xhci: rework xhci_print_ir_set() to get ir set from xhci itselfDmitry Torokhov
xhci->ir_set points to __iomem region, but xhci_print_ir_set accepts plain struct xhci_intr_reg * causing multiple sparse warning at call sites and inside the fucntion when we try to read that memory. Instead of adding __iomem qualifier to the argument let's rework the function so it itself gets needed register set from xhci and prints it. Signed-off-by: Dmitry Torokhov <dtor@vmware.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2011-01-14xhci: Use GFP_NOIO during device reset.Sarah Sharp
When xhci_discover_or_reset_device() is called after a host controller power loss, the virtual device may need to be reallocated. Make sure xhci_alloc_dev() uses GFP_NOIO. This avoid causing a deadlock by allowing the kernel to flush pending I/O while reallocating memory for a virtual device for a USB mass storage device that's holding the backing store for dirty memory buffers. This patch should be queued for the 2.6.37 stable tree. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable@kernel.org
2011-01-14xhci: Do not run xhci_cleanup_msix with irq disabledZhang Rui
when unloading xhci_hcd, I got: [ 134.856813] xhci_hcd 0000:02:00.0: remove, state 4 [ 134.858140] usb usb3: USB disconnect, address 1 [ 134.874956] xhci_hcd 0000:02:00.0: Host controller not halted, aborting reset. [ 134.876351] BUG: sleeping function called from invalid context at kernel/mutex.c:85 [ 134.877657] in_atomic(): 0, irqs_disabled(): 1, pid: 1451, name: modprobe [ 134.878975] Pid: 1451, comm: modprobe Not tainted 2.6.37-rc5+ #162 [ 134.880298] Call Trace: [ 134.881602] [<ffffffff8104156a>] __might_sleep+0xeb/0xf0 [ 134.882921] [<ffffffff814763dc>] mutex_lock+0x24/0x50 [ 134.884229] [<ffffffff810a745c>] free_desc+0x2e/0x5f [ 134.885538] [<ffffffff810a74c8>] irq_free_descs+0x3b/0x71 [ 134.886853] [<ffffffff8102584d>] free_irq_at+0x31/0x36 [ 134.888167] [<ffffffff8102723f>] destroy_irq+0x69/0x71 [ 134.889486] [<ffffffff8102747a>] native_teardown_msi_irq+0xe/0x10 [ 134.890820] [<ffffffff8124c382>] default_teardown_msi_irqs+0x57/0x80 [ 134.892158] [<ffffffff8124be46>] free_msi_irqs+0x8b/0xe9 [ 134.893504] [<ffffffff8124cd46>] pci_disable_msix+0x35/0x39 [ 134.894844] [<ffffffffa01b444a>] xhci_cleanup_msix+0x31/0x51 [xhci_hcd] [ 134.896186] [<ffffffffa01b4b3a>] xhci_stop+0x3a/0x80 [xhci_hcd] [ 134.897521] [<ffffffff81341dd4>] usb_remove_hcd+0xfd/0x14a [ 134.898859] [<ffffffff813500ae>] usb_hcd_pci_remove+0x5c/0xc6 [ 134.900193] [<ffffffff8123c606>] pci_device_remove+0x3f/0x91 [ 134.901535] [<ffffffff812e7ea4>] __device_release_driver+0x83/0xd9 [ 134.902899] [<ffffffff812e8571>] driver_detach+0x86/0xad [ 134.904222] [<ffffffff812e7d56>] bus_remove_driver+0xb2/0xd8 [ 134.905540] [<ffffffff812e8633>] driver_unregister+0x6c/0x74 [ 134.906839] [<ffffffff8123c8e4>] pci_unregister_driver+0x44/0x89 [ 134.908121] [<ffffffffa01b940e>] xhci_unregister_pci+0x15/0x17 [xhci_hcd] [ 134.909396] [<ffffffffa01bd7d2>] xhci_hcd_cleanup+0xe/0x10 [xhci_hcd] [ 134.910652] [<ffffffff8107fcd1>] sys_delete_module+0x1ca/0x23b [ 134.911882] [<ffffffff81123932>] ? path_put+0x22/0x26 [ 134.913104] [<ffffffff8109a800>] ? audit_syscall_entry+0x2c/0x148 [ 134.914333] [<ffffffff8100ac82>] system_call_fastpath+0x16/0x1b [ 134.915658] xhci_hcd 0000:02:00.0: USB bus 3 deregistered [ 134.916465] xhci_hcd 0000:02:00.0: PCI INT A disabled and the same issue when xhci_suspend is invoked. (Note from Sarah: That's fixed by Andiry's patch before this, by synchronizing the irqs rather than freeing them on suspend.) Do not run xhci_cleanup_msix with irq disabled. This patch should be queued for the 2.6.37 stable tree. Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable@kernel.org
2011-01-14xHCI: synchronize irq in xhci_suspend()Andiry Xu
Synchronize the interrupts instead of free them in xhci_suspend(). This will prevent a double free when the host is suspended and then the card removed. Set the flag hcd->msix_enabled when using MSI-X, and check the flag in suspend_common(). MSI-X synchronization will be handled by xhci_suspend(), and MSI/INTx will be synchronized in suspend_common(). This patch should be queued for the 2.6.37 stable tree. Reported-by: Matthew Garrett <mjg@redhat.com> Signed-off-by: Andiry Xu <andiry.xu@amd.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable@kernel.org
2010-11-19xhci: Fix reset-device and configure-endpoint commandsPaul Zimmerman
We have been having problems with the USB-IF Gold Tree tests when plugging and unplugging devices from the tree. I have seen that the reset-device and configure-endpoint commands, which are invoked from xhci_discover_or_reset_device() and xhci_configure_endpoint(), will sometimes time out. After much debugging, I determined that the commands themselves do not actually time out, but rather their completion events do not get delivered to the right place. This happens when the command ring has just wrapped around, and it's enqueue pointer is left pointing to the link TRB. xhci_discover_or_reset_device() and xhci_configure_endpoint() use the enqueue pointer directly as their command TRB pointer, without checking whether it's pointing to the link TRB. When the completion event arrives, if the command TRB is pointing to the link TRB, the check against the command ring dequeue pointer in handle_cmd_in_cmd_wait_list() fails, so the completion inside the command does not get signaled. The patch below fixes the timeout problem for me. This should be queued for the 2.6.35 and 2.6.36 stable trees. Signed-off-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable@kernel.org
2010-11-15xhci: Fix command ring replay after resume.Sarah Sharp
Andiry's xHCI bus suspend patch introduced the possibly of a host controller replaying old commands on the command ring, if the host successfully restores the registers after a resume. After a resume from suspend, the xHCI driver must restore the registers, including the command ring pointer. I had suggested that Andiry set the command ring pointer to the current command ring dequeue pointer, so that the driver wouldn't have to zero the command ring. Unfortunately, setting the command ring pointer to the current dequeue pointer won't work because the register assumes the pointer is 64-byte aligned, and TRBs on the command ring are 16-byte aligned. The lower seven bits will always be masked off, leading to the written pointer being up to 3 TRBs behind the intended pointer. Here's a log excerpt. On init, the xHCI driver places a vendor-specific command on the command ring: [ 215.750958] xhci_hcd 0000:01:00.0: Vendor specific event TRB type = 48 [ 215.750960] xhci_hcd 0000:01:00.0: NEC firmware version 30.25 [ 215.750962] xhci_hcd 0000:01:00.0: Command ring deq = 0x3781e010 (DMA) When we resume, the command ring dequeue pointer to be written should have been 0x3781e010. Instead, it's 0x3781e000: [ 235.557846] xhci_hcd 0000:01:00.0: // Setting command ring address to 0x3781e001 [ 235.557848] xhci_hcd 0000:01:00.0: `MEM_WRITE_DWORD(3'b000, 64'hffffc900100bc038, 64'h3781e001, 4'hf); [ 235.557850] xhci_hcd 0000:01:00.0: `MEM_WRITE_DWORD(3'b000, 32'hffffc900100bc020, 32'h204, 4'hf); [ 235.557866] usb usb9: root hub lost power or was reset (I can't see the results of this bug because the xHCI restore always fails on this box, and the xHCI driver re-allocates everything.) The fix is to zero the command ring and put the software and hardware enqueue and dequeue pointer back to the beginning of the ring. We do this before the system suspends, to be paranoid and prevent the BIOS from starting the host without clearing the command ring pointer, which might cause the host to muck with stale memory. (The pointer isn't required to be in the suspend power well, but it could be.) The command ring pointer is set again after the host resumes. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Tested-by: Andiry Xu <andiry.xu@amd.com>
2010-11-11xHCI: release spinlock when setup interruptAndiry Xu
Jiri Slaby reports spinlock is held while calling kmalloc(GFP_KERNEL) and request_irq() in xhci_resume(). Release the spinlock when setup interrupt. Reported-by: Jiri Slaby <jirislaby@gmail.com> Signed-off-by: Andiry Xu <andiry.xu@amd.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2010-11-11Revert "USB: xhci: Use GFP_ATOMIC under spin_lock"Greg Kroah-Hartman
This reverts commit ef821ae70fc35a76bdce7e07c70a1a7c2c33cdb9. The correct thing to do is to drop the spinlock, not change the GFP flag here. Thanks to Sarah for pointing out I shouldn't have taken this patch in the first place. Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: David Sterba <dsterba@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-11-11USB: xhci: Use GFP_ATOMIC under spin_lockDavid Sterba
coccinelle check scripts/coccinelle/locks/call_kern.cocci found that in drivers/usb/host/xhci.c an allocation with GFP_KERNEL is done with locks held: xhci_resume spin_lock_irq(xhci->lock) xhci_setup_msix kmalloc(GFP_KERNEL) Change it to GFP_ATOMIC. Signed-off-by: David Sterba <dsterba@suse.cz> CC: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-10-22usb: Fix linker errors with CONFIG_PM=nSarah Sharp
Fix these linker errors when CONFIG_PM=n: ERROR: "xhci_bus_resume" [drivers/usb/host/xhci-hcd.ko] undefined! ERROR: "xhci_bus_suspend" [drivers/usb/host/xhci-hcd.ko] undefined! Reported-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Acked-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-10-22USB: xhci: Fix compile error when CONFIG_PM=nSarah Sharp
Fix this error when CONFIG_PM is not enabled: drivers/usb/host/xhci.c:675: error: implicit declaration of function 'usb_root_hub_lost_power' Wrap xhci_suspend() and xhci_resume() into an ifdef CONFIG_PM, along with the functions that only they call -- xhci_save_registers() and xhci_restore_registers(). Reported-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-10-22USB: xHCI: PCI power management implementationAndiry Xu
This patch implements the PCI suspend/resume. Please refer to xHCI spec for doing the suspend/resume operation. For S3, CSS/SRS in USBCMD is used to save/restore the internal state. However, an error maybe occurs while restoring the internal state. In this case, it means that HC internal state is wrong and HC will be re-initialized. Signed-off-by: Libin Yang <libin.yang@amd.com> Signed-off-by: Dong Nguyen <dong.nguyen@amd.com> Signed-off-by: Andiry Xu <andiry.xu@amd.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-10-22USB: xHCI: port power management implementationAndiry Xu
Add software trigger USB device suspend resume function hook. Do port suspend & resume in terms of xHCI spec. Port Suspend: Stop all endpoints via Stop Endpoint Command with Suspend (SP) flag set. Place individual ports into suspend mode by writing '3' for Port Link State (PLS) field into PORTSC register. This can only be done when the port is in Enabled state. When writing, the Port Link State Write Strobe (LWS) bit shall be set to '1'. Allocate an xhci_command and stash it in xhci_virt_device to wait completion for the last Stop Endpoint Command. Use the Suspend bit in TRB to indicate the Stop Endpoint Command is for port suspend. Based on Sarah's suggestion. Port Resume: Write '0' in PLS field, device will transition to running state. Ring an endpoints' doorbell to restart it. Ref: USB device remote wake need another patch to implement. For details of how USB subsystem do power management, please see: Documentation/usb/power-management.txt Signed-off-by: Crane Cai <crane.cai@amd.com> Signed-off-by: Libin Yang <libin.yang@amd.com> Signed-off-by: Andiry Xu <andiry.xu@amd.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-10-22USB: core: use kernel assigned address for devices under xHCIAndiry Xu
xHCI driver uses hardware assigned device address. This may cause device address conflict in certain cases. Use kernel assigned address for devices under xHCI. Store the xHC assigned address locally in xHCI driver. Signed-off-by: Andiry Xu <andiry.xu@amd.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2010-10-22USB: xHCI: change xhci_reset_device() to allocate new deviceAndiry Xu
Rename xhci_reset_device() to xhci_discover_or_reset_device(). If xhci_discover_or_reset_device() is called to reset a device which does not exist or does not match the udev, it calls xhci_alloc_dev() to re-allocate the device. This would prevent the reset device failure, possibly due to the xHC restore error during S3/S4 resume. Signed-off-by: Andiry Xu <andiry.xu@amd.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-10-22USB: xHCI: Add pointer to udev in struct xhci_virt_deviceAndiry Xu
Add a pointer to udev in struct xhci_virt_device. When allocate a new virt_device, make the pointer point to the corresponding udev. Modify xhci_check_args(), check if virt_dev->udev matches the target udev, to make sure command is issued to the right device. Signed-off-by: Andiry Xu <andiry.xu@amd.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-08-10USB: xhci: Performance - move interrupt handlers into xhci-ring.cSarah Sharp
Most of the work for interrupt handling is done in xhci-ring.c, so it makes sense to move the functions that are first called when an interrupt happens (xhci_irq() or xhci_msi_irq()) into xhci-ring.c, so that the compiler can better optimize them. Shorten some lines to make it pass checkpatch. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-08-10USB: xhci: Performance - move functions that find ep ring.Sarah Sharp
I've been using perf to measure the top symbols while transferring 1GB of data on a USB 3.0 drive with dd. This is using the raw disk with /dev/sdb, with a block size of 1K. During performance testing, the top symbol was xhci_triad_to_transfer_ring(), a function that should return immediately if streams are not enabled for an endpoint. It turned out that the functions to find the endpoint ring was defined in xhci-mem.c and used in xhci-ring.c and xhci-hcd.c. I moved a copy of xhci_triad_to_transfer_ring() and xhci_urb_to_transfer_ring() into xhci-ring.c and declared them static. I also made a static version of xhci_urb_to_transfer_ring() in xhci.c. This improved throughput on a 1GB read of the raw disk with dd from 186MB/s to 195MB/s, and perf reported sampling the xhci_triad_to_transfer_ring() 0.06% of the time, rather than 9.26% of the time. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-08-10USB: xHCI: Isoc urb enqueueAndiry Xu
Enable isochronous urb enqueue. Signed-off-by: Andiry Xu <andiry.xu@amd.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-08-10USB: xHCI: Introduce urb_priv structureAndiry Xu
Add urb_priv data structure to xHCI driver. This structure allows multiple xhci TDs to be linked to one urb, which is essential for isochronous transfer. For non-isochronous urb, only one TD is needed for one urb; for isochronous urb, the TD number for the urb is equal to urb->number_of_packets. The length field of urb_priv indicates the number of TDs in the urb. The td_cnt field indicates the number of TDs already processed by xHC. When td_cnt matches length, the urb can be given back to usbcore. When an urb is dequeued or cancelled, add all the unprocessed TDs to the endpoint's cancelled_td_list. When process a cancelled TD, increase td_cnt field. When td_cnt equals urb_priv->length, giveback the cancelled urb. Signed-off-by: Andiry Xu <andiry.xu@amd.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-08-10USB: xHCI: Supporting MSI/MSI-XDong Nguyen
Enable MSI/MSI-X supporting in xhci driver. Provide the mechanism to fall back using MSI and Legacy IRQs if MSI-X IRQs register failed. Signed-off-by: Dong Nguyen <Dong.Nguyen@amd.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>, Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-08-10USB: convert usb_hcd bitfields into atomic flagsAlan Stern
This patch (as1393) converts several of the single-bit fields in struct usb_hcd to atomic flags. This is for safety's sake; not all CPUs can update bitfield values atomically, and these flags are used in multiple contexts. The flag fields that are set only during registration or removal can remain as they are, since non-atomic accesses at those times will not cause any problems. (Strictly speaking, the authorized_default flag should become atomic as well. I didn't bother with it because it gets changed only via sysfs. It can be done later, if anyone wants.) Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-08-10USB: xhci: Remove obsolete debugging printk.Sarah Sharp
When code to manipulate the command register was refactored from xhci_run() to xhci_start(), a debugging statement was left behind that no longer applies. Remove that statement. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Reported-by: Sergei Shtylyov <sshtylyov@mvista.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-07-26USB: xhci: Set EP0 dequeue ptr after reset of configured device.Sarah Sharp
When a configured device is reset, the control endpoint's ring is reused. If control transfers to the device were issued before the device is reset, the dequeue pointer will be somewhere in the middle of the ring. If the device is then issued an address with the set address command, the xHCI driver must provide a valid input context for control endpoint zero. The original code would give the hardware the original input context, which had a dequeue pointer set to the top of the ring. This would cause the host to re-execute any control transfers until it reached the ring's enqueue pointer. When issuing a set address command for a device that has just been configured and then reset, use the control endpoint's enqueue pointer as the hardware's dequeue pointer. Assumption: All control transfers will be completed or cancelled before the set address command is issued to the device. If there are any outstanding control transfers, this code will not work. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-06-04USB: xhci: Print NEC firmware version.Sarah Sharp
The NEC xHCI host controller firmware version can be found by putting a vendor-specific command on the command ring and extracting the BCD encoded-version out of the vendor-specific event TRB. The firmware version debug line in dmesg will look like: xhci_hcd 0000:05:00.0: NEC firmware version 30.21 (NEC merged with Renesas Technologies and became Renesas Electronics on April 1, 2010. I have their OK to merge this vendor-specific code.) Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: Satoshi Otani <satoshi.otani.xm@renesas.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-06-04USB: xhci: Wait for host to start running.Sarah Sharp
When the run bit is set in the xHCI command register, it may take a few microseconds for the host to start running. We cannot ring any doorbells until the host is actually running, so wait until the status register says the host is running. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Reported-by: Shinya Saito <shinya.saito.sx@renesas.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-06-04USB: xhci: Wait for controller to be ready after reset.Sarah Sharp
After software resets an xHCI host controller, it must wait for the "Controller Not Ready" (CNR) bit in the status register to be cleared. Software is not supposed to ring any doorbells or write to any registers except the status register until this bit is cleared. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-05-20USB: xhci: Set stream ID to 0 after cleaning up stalls.Sarah Sharp
After using state stored in xhci_virt_ep to clean up a stalled endpoint, be sure to set the stalled stream ID back to 0. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-05-20USB: xhci: Avoid double free after streams are disabled.Sarah Sharp
When a device is disconnected, xhci_free_virt_device() is called. Ramya found that if the device had streams enabled, and then the driver freed the streams with a call to usb_free_streams(), then about a minute after he had called this, his machine crashed with a Bad DMA error. It turns out that xhci_free_virt_device() would attempt to free the endpoint's stream_info data structure if it wasn't NULL, and the free streams function was not setting it to NULL after freeing it. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Tested-by: Ramya Desai <ramya.desai@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-05-20USB: remove the usb_host_ss_ep_comp structureAlan Stern
This patch (as1375) eliminates the usb_host_ss_ep_comp structure used for storing a dynamically-allocated copy of the SuperSpeed endpoint companion descriptor. The SuperSpeed descriptor is placed directly in the usb_host_endpoint structure, alongside the standard endpoint descriptor. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-05-20USB: xhci: Correct assumptions about number of rings per endpoint.Sarah Sharp
Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-05-20USB: xhci: Add memory allocation for USB3 bulk streams.Sarah Sharp
Add support for allocating streams for USB 3.0 bulk endpoints. See Documentation/usb/bulk-streams.txt for more information about how and why you would use streams. When an endpoint has streams enabled, instead of having one ring where all transfers are enqueued to the hardware, it has several rings. The ring dequeue pointer in the endpoint context is changed to point to a "Stream Context Array". This is basically an array of pointers to transfer rings, one for each stream ID that the driver wants to use. The Stream Context Array size must be a power of two, and host controllers can place a limit on the size of the array (4 to 2^16 entries). These two facts make calculating the size of the Stream Context Array and the number of entries actually used by the driver a bit tricky. Besides the Stream Context Array and rings for all the stream IDs, we need one more data structure. The xHCI hardware will not tell us which stream ID a transfer event was for, but it will give us the slot ID, endpoint index, and physical address for the TRB that caused the event. For every endpoint on a device, add a radix tree to map physical TRB addresses to virtual segments within a stream ring. Keep track of whether an endpoint is transitioning to using streams, and don't enqueue any URBs while that's taking place. Refuse to transition an endpoint to streams if there are already URBs enqueued for that endpoint. We need to make sure that freeing streams does not fail, since a driver's disconnect() function may attempt to do this, and it cannot fail. Pre-allocate the command structure used to issue the Configure Endpoint command, and reserve space on the command ring for each stream endpoint. This may be a bit overkill, but it is permissible for the driver to allocate all streams in one call and free them in multiple calls. (It is not advised, however, since it is a waste of resources and time.) Even with the memory and ring room pre-allocated, freeing streams can still fail because the xHC rejects the configure endpoint command. It is valid (by the xHCI 0.96 spec) to return a "Bandwidth Error" or a "Resource Error" for a configure endpoint command. We should never see a Bandwidth Error, since bulk endpoints do not effect the reserved bandwidth. The host controller can still return a Resource Error, but it's improbable since the xHC would be going from a more resource-intensive configuration (streams) to a less resource-intensive configuration (no streams). If the xHC returns a Resource Error, the endpoint will be stuck with streams and will be unusable for drivers. It's an unavoidable consequence of broken host controller hardware. Includes bug fixes from the original patch, contributed by John Youn <John.Youn@synopsys.com> and Andy Green <AGreen@PLXTech.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-05-20USB: xhci: Fix issue with set interface after stall.Sarah Sharp
When the USB core installs a new interface, it unconditionally clears the halts on all the endpoints on the new interface. Usually the xHCI host needs to know when an endpoint is reset, so it can change its internal endpoint state. In this case, it doesn't care, because the endpoints were never halted in the first place. To avoid issuing a redundant Reset Endpoint command, the xHCI driver looks at xhci_virt_ep->stopped_td to determine if the endpoint was actually halted. However, the functions that handle the stall never set that variable to NULL after it dealt with the stall. So if an endpoint stalled and a Reset Endpoint command completed, and then the class driver tried to install a new alternate setting, the xHCI driver would access the old xhci_virt_ep->stopped_td pointer. A similar problem occurs if the endpoint has been stopped to cancel a transfer. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-30include cleanup: Update gfp.h and slab.h includes to prepare for breaking ↵Tejun Heo
implicit slab.h inclusion from percpu.h percpu.h is included by sched.h and module.h and thus ends up being included when building most .c files. percpu.h includes slab.h which in turn includes gfp.h making everything defined by the two files universally available and complicating inclusion dependencies. percpu.h -> slab.h dependency is about to be removed. Prepare for this change by updating users of gfp and slab facilities include those headers directly instead of assuming availability. As this conversion needs to touch large number of source files, the following script is used as the basis of conversion. http://userweb.kernel.org/~tj/misc/slabh-sweep.py The script does the followings. * Scan files for gfp and slab usages and update includes such that only the necessary includes are there. ie. if only gfp is used, gfp.h, if slab is used, slab.h. * When the script inserts a new include, it looks at the include blocks and try to put the new include such that its order conforms to its surrounding. It's put in the include block which contains core kernel includes, in the same order that the rest are ordered - alphabetical, Christmas tree, rev-Xmas-tree or at the end if there doesn't seem to be any matching order. * If the script can't find a place to put a new include (mostly because the file doesn't have fitting include block), it prints out an error message indicating which .h file needs to be added to the file. The conversion was done in the following steps. 1. The initial automatic conversion of all .c files updated slightly over 4000 files, deleting around 700 includes and adding ~480 gfp.h and ~3000 slab.h inclusions. The script emitted errors for ~400 files. 2. Each error was manually checked. Some didn't need the inclusion, some needed manual addition while adding it to implementation .h or embedding .c file was more appropriate for others. This step added inclusions to around 150 files. 3. The script was run again and the output was compared to the edits from #2 to make sure no file was left behind. 4. Several build tests were done and a couple of problems were fixed. e.g. lib/decompress_*.c used malloc/free() wrappers around slab APIs requiring slab.h to be added manually. 5. The script was run on all .h files but without automatically editing them as sprinkling gfp.h and slab.h inclusions around .h files could easily lead to inclusion dependency hell. Most gfp.h inclusion directives were ignored as stuff from gfp.h was usually wildly available and often used in preprocessor macros. Each slab.h inclusion directive was examined and added manually as necessary. 6. percpu.h was updated not to include slab.h. 7. Build test were done on the following configurations and failures were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my distributed build env didn't work with gcov compiles) and a few more options had to be turned off depending on archs to make things build (like ipr on powerpc/64 which failed due to missing writeq). * x86 and x86_64 UP and SMP allmodconfig and a custom test config. * powerpc and powerpc64 SMP allmodconfig * sparc and sparc64 SMP allmodconfig * ia64 SMP allmodconfig * s390 SMP allmodconfig * alpha SMP allmodconfig * um on x86_64 SMP allmodconfig 8. percpu.h modifications were reverted so that it could be applied as a separate patch and serve as bisection point. Given the fact that I had only a couple of failures from tests on step 6, I'm fairly confident about the coverage of this conversion patch. If there is a breakage, it's likely to be something in one of the arch headers which should be easily discoverable easily on most builds of the specific arch. Signed-off-by: Tejun Heo <tj@kernel.org> Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
2010-03-19USB: xHCI: re-initialize cmd_completionAndiry Xu
When a signal interrupts a Configure Endpoint command, the cmd_completion used in xhci_configure_endpoint() is not re-initialized and the wait_for_completion_interruptible_timeout() will return failure. Initialize cmd_completion in xhci_configure_endpoint(). Signed-off-by: Andiry Xu <andiry.xu@amd.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-19USB: xhci: rename driver to xhci_hcdAlex Chiang
Naming consistency with other USB HCDs. Signed-off-by: Alex Chiang <achiang@hp.com> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>