| Age | Commit message (Collapse) | Author |
|---|
|
This patch does two things for SCM eUSCSI USB-SCSI converters:
1. SCM eUSCSI bridge devices are hard-wired to use SCSI ID 7. On connecting
the converter, access to that ID is attempted during the bus scan. Asking
the converter to issue INQUIRY commands to itself isn't very polite and
wastes time. Set this_id to 7 so __scsi_scan_target() skips it in the scan.
2. Enable multi-LUN support. eUSCSI devices don't support Get Max LUN
requests, returning an error (-32). [Different targets could have different
numbers of LUNs, so it wouldn't make sense to return a particular value in
response to Get Max LUN.]
usb_stor_scan_dwork() does this:
/* For bulk-only devices, determine the max LUN value */
if (us->protocol == USB_PR_BULK && !(us->fflags & US_FL_SINGLE_LUN)) {
mutex_lock(&us->dev_mutex);
us->max_lun = usb_stor_Bulk_max_lun(us);
mutex_unlock(&us->dev_mutex);
It avoids calling usb_stor_Bulk_max_lun() if US_FL_SINGLE_LUN, but not for
US_FL_SCM_MULT_TARG. Since usb_stor_Bulk_max_lun() returns 0 in the error
case, us->max_lun was always set to 0.
[If the user doesn't want multi-LUN support (perhaps there are SCSI devices
which respond to commands on all LUNs?), the US_FL_SINGLE_LUN quirk can be
specified on the kernel command line.]
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big USB patchset for 3.18-rc1. Also in here is the PHY
tree, as it seems to fit well with the USB tree for various reasons...
Anyway, lots of little changes in here, all over the place, full
details in the changelog
All have been in the linux-next tree for a while with no issues"
* tag 'usb-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (244 commits)
USB: host: st: fix typo 'CONFIG_USB_EHCI_HCD_ST'
uas: Reduce number of function arguments for uas_alloc_foo functions
xhci: Allow xHCI drivers to be built as separate modules
xhci: Export symbols used by host-controller drivers
xhci: Check for XHCI_COMP_MODE_QUIRK when disabling D3cold
xhci: Introduce xhci_init_driver()
usb: hcd: add generic PHY support
usb: rename phy to usb_phy in HCD
usb: gadget: uvc: fix up uvcg_v4l2_get_unmapped_area typo
USB: host: st: fix ehci/ohci driver selection
usb: host: ehci-exynos: Remove unnecessary usb-phy support
usb: core: return -ENOTSUPP for all targeted hosts
USB: Remove .owner field for driver
usb: core: log higher level message on malformed LANGID descriptor
usb: Add LED triggers for USB activity
usb: Rename usb-common.c
usb: gadget: Refactor request completion
usb: gadget: Introduce usb_gadget_giveback_request()
usb: dwc2/gadget: move phy bus legth initialization
phy: remove .owner field for drivers using module_platform_driver
...
|
|
Fixed typos in comments of various drivers/usb files
Signed-off-by: Mickael Maison <mickael.maison@gmail.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Besides the ASM1051 (*) needing sdev->no_report_opcodes = 1, it turns out that
the JMicron JMS567 also needs it to work properly with uas (usb-storage always
sets it). Since some of the scsi devs were not to keen on the idea to
outrightly set sdev->no_report_opcodes = 1 for all uas devices, so add a quirk
for this, and set it for the JMS567.
*) Which has become a non-issue since we've completely blacklisted uas on
the ASM1051 for other reasons
Cc: stable@vger.kernel.org
Reported-and-tested-by: Claudio Bizzarri <claudio.bizzarri@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
And set this quirk for the Seagate Expansion Desk (0bc2:2312), as that one
seems to hang upon receiving an ATA_12 or ATA_16 command.
https://bugzilla.kernel.org/show_bug.cgi?id=79511
https://bbs.archlinux.org/viewtopic.php?id=183190
While at it also add missing documentation for the u value for usb-storage
quirks.
Cc: stable@vger.kernel.org # 3.16, 3.17
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
--
Changes in v2: Add documentation for new t and u usb-storage.quirks flags
Changes in v3: Fix typo in documentation
Changes in v4: Also apply the quirk to (0bc2:3312)
Changes in v5: Rebased on 3.17-rc5, drop u documentation, already upstream
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The SCSI specification requires that the second Command Data Byte
should contain the LUN value in its high-order bits if the recipient
device reports SCSI level 2 or below. Nevertheless, some USB
mass-storage devices use those bits for other purposes in
vendor-specific commands. Currently Linux has no way to send such
commands, because the SCSI stack always overwrites the LUN bits.
Testing shows that Windows 7 and XP do not store the LUN bits in the
CDB when sending commands to a USB device. This doesn't matter if the
device uses the Bulk-Only or UAS transports (which virtually all
modern USB mass-storage devices do), as these have a separate
mechanism for sending the LUN value.
Therefore this patch introduces a flag in the Scsi_Host structure to
inform the SCSI midlayer that a transport does not require the LUN
bits to be stored in the CDB, and it makes usb-storage set this flag
for all devices using the Bulk-Only transport. (UAS is handled by a
separate driver, but it doesn't really matter because no SCSI-2 or
lower device is at all likely to use UAS.)
The patch also cleans up the code responsible for storing the LUN
value by adding a bitflag to the scsi_device structure. The test for
whether to stick the LUN value in the CDB can be made when the device
is probed, and stored for future use rather than being made over and
over in the fast path.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Tiziano Bacocco <tiziano.bacocco@gmail.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The SCSI standard defines 64-bit values for LUNs, and large arrays
employing large or hierarchical LUN numbers become more and more
common.
So update the linux SCSI stack to use 64-bit LUN numbers.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
uas devices have 2 alternative settings on their usb-storage interface,
one for usb-storage and one for uas. Using the uas driver is preferred, so if
the uas driver is enabled, and the device has an uas alt setting, don't bind.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now that Joe cleaned up the init/exit functions, we can just get rid of
them entirely and use the proper macro that almost all other USB drivers
now use.
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use a more current logging style with dev_printk
where possible.
o Convert uses of US_DEBUGP to usb_stor_dbg
o Add "struct us_data *" to usb_stor_dbg uses
o usb_stor_dbg now uses struct device */dev_vprint_emit
o Removed embedded function names
o Coalesce formats
o Remove trailing whitespace
o Remove useless OOM messages
o Remove useless function entry/exit logging
o Convert some US_DEBUGP uses to dev_info and dev_dbg
Object size is slightly reduced when debugging
is enabled, slightly increased with no debugging
because some initialization and removal messages
are now always emitted.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This pulls in a bunch of fixes that are in Linus's tree because we need them
here for testing and development.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
1. Define a new macro for USB storage match rules:
matching with Vendor ID and interface descriptors.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch sets scsi_host->max_id as 1 if the device's quirk
flag of US_FL_SCM_MULT_TARG isn't set, because there are only 6
mass storage devices marked as mutiple targets from unusual_devs.h.
This patch is a small optimization about scanning targets, and
avoid scanning other 7 non-existed targets for single target
device.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
scsi_host_alloc() will zero our private data, no need to memset it.
Signed-off-by: Yan Hong <clouds.yan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The "Low Performance USB Block driver" has been removed which a user of
libusual. Now we have only the usb-storage driver as the only driver in
tree. This makes libusual needless.
This patch removes libusal, fixes up all users. The usual-table is now
linked into usb-storage.
usb_usual.h remains in public include directory because some staging
users seem to need it.
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support for write cache quirk on usb hdd. scsi driver will be set to wce
by detecting write cache quirk in quirk list when plugging usb hdd.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Pankaj Kumar <pankaj.km@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Fixed keyword related space issues found by
checkpatch.pl tool in drivers/usb/storage/usb.c
Signed-off-by: Jeffrin Jose <ahiliation@yahoo.co.in>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fixed several trailing white spaces issues found
by checkpatch.pl tool in drivers/usb/storage/usb.c
Signed-off-by: Jeffrin Jose <ahiliation@yahoo.co.in>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fixed C99 comment issue in drivers/usb/storage/usb.c
found using checkpatch.pl tool.
Signed-off-by: Jeffrin Jose <ahiliation@yahoo.co.in>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch fixes one lockdep warning[1] inside usb_stor_pre_reset.
If the current configuration includes multiple mass storage interfaces,
the 'AA' lockdep warning will be triggered since the lock class of
'us->dev_mutex' is acquired two times in .reset path. It isn't
a real deadlock, so just take the lockdep_set_class annotation to
remove the warning.
[1], lockdep warning log
:[ INFO: possible recursive locking detected ]
:3.3.0-0.rc5.git3.1.fc17.x86_64 #1 Tainted: G W
:---------------------------------------------
:usb-storage/14846 is trying to acquire lock:
: (&(us->dev_mutex)){+.+.+.}, at: [<ffffffffa0481c0c>] usb_stor_pre_reset+0x1c/0x20 [usb_storage]
:but task is already holding lock:
: (&(us->dev_mutex)){+.+.+.}, at: [<ffffffffa0481c0c>] usb_stor_pre_reset+0x1c/0x20 [usb_storage]
:other info that might help us debug this:
: Possible unsafe locking scenario:
: CPU0
: ----
: lock(&(us->dev_mutex));
: lock(&(us->dev_mutex));
: *** DEADLOCK ***
: May be due to missing lock nesting notation
:2 locks held by usb-storage/14846:
: #0: (&__lockdep_no_validate__){......}, at: [<ffffffff8147e6a5>] usb_lock_device_for_reset+0x95/0x100
: #1: (&(us->dev_mutex)){+.+.+.}, at: [<ffffffffa0481c0c>] usb_stor_pre_reset+0x1c/0x20 [usb_storage]
:stack backtrace:
:Pid: 14846, comm: usb-storage Tainted: G W 3.3.0-0.rc5.git3.1.fc17.x86_64 #1
:Call Trace:
: [<ffffffff810cbdaf>] __lock_acquire+0x168f/0x1bb0
: [<ffffffff81021083>] ? native_sched_clock+0x13/0x80
: [<ffffffff810210f9>] ? sched_clock+0x9/0x10
: [<ffffffff810210f9>] ? sched_clock+0x9/0x10
: [<ffffffff810a2975>] ? sched_clock_local+0x25/0xa0
: [<ffffffff810cc9a1>] lock_acquire+0xa1/0x1e0
: [<ffffffffa0481c0c>] ? usb_stor_pre_reset+0x1c/0x20 [usb_storage]
: [<ffffffff81699c86>] mutex_lock_nested+0x76/0x3a0
: [<ffffffffa0481c0c>] ? usb_stor_pre_reset+0x1c/0x20 [usb_storage]
: [<ffffffffa0481c0c>] ? usb_stor_pre_reset+0x1c/0x20 [usb_storage]
: [<ffffffffa0481c0c>] usb_stor_pre_reset+0x1c/0x20 [usb_storage]
: [<ffffffff8148184d>] usb_reset_device+0x7d/0x190
: [<ffffffffa048119c>] usb_stor_port_reset+0x7c/0x80 [usb_storage]
: [<ffffffffa0481234>] usb_stor_invoke_transport+0x94/0x560 [usb_storage]
: [<ffffffff810cd3b2>] ? mark_held_locks+0xb2/0x130
: [<ffffffff8169dbd0>] ? _raw_spin_unlock_irq+0x30/0x50
: [<ffffffffa047fe3e>] usb_stor_transparent_scsi_command+0xe/0x10 [usb_storage]
: [<ffffffffa0481ae3>] usb_stor_control_thread+0x173/0x280 [usb_storage]
: [<ffffffffa0481970>] ? fill_inquiry_response+0x20/0x20 [usb_storage]
: [<ffffffff8108a3f7>] kthread+0xb7/0xc0
: [<ffffffff816a7d34>] kernel_thread_helper+0x4/0x10
: [<ffffffff8169e0f4>] ? retint_restore_args+0x13/0x13
: [<ffffffff8108a340>] ? kthread_worker_fn+0x1a0/0x1a0
: [<ffffffff816a7d30>] ? gs_change+0x13/0x13
Reported-By: Dave Jones <davej@redhat.com>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is to pull in the xhci changes and the other fixes and device id
updates that were done in Linus's tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch (as1521b) fixes the interaction between usb-storage's
scanning thread and the freezer. The current implementation has a
race: If the device is unplugged shortly after being plugged in and
just as a system sleep begins, the scanning thread may get frozen
before the khubd task. Khubd won't be able to freeze until the
disconnect processing is complete, and the disconnect processing can't
proceed until the scanning thread finishes, so the sleep transition
will fail.
The implementation in the 3.2 kernel suffers from an additional
problem. There the scanning thread calls set_freezable_with_signal(),
and the signals sent by the freezer will mess up the thread's I/O
delays, which are all interruptible.
The solution to both problems is the same: Replace the kernel thread
used for scanning with a delayed-work routine on the system freezable
work queue. Freezable work queues have the nice property that you can
cancel a work item even while the work queue is frozen, and no signals
are needed.
The 3.2 version of this patch solves the problem in Bugzilla #42730.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Seth Forshee <seth.forshee@canonical.com>
CC: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Enable usb-storage support dynamic id again by using a fixed id entry
that describes a device using the Bulk-Only transport with the
Transparent SCSI protocol.
Signed-off-by: Huajun Li <huajun.li.lee@gmail.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (232 commits)
USB: Add USB-ID for Multiplex RC serial adapter to cp210x.c
xhci: Clean up 32-bit build warnings.
USB: update documentation for usbmon
usb: usb-storage doesn't support dynamic id currently, the patch disables the feature to fix an oops
drivers/usb/class/cdc-acm.c: clear dangling pointer
drivers/usb/dwc3/dwc3-pci.c: introduce missing kfree
drivers/usb/host/isp1760-if.c: introduce missing kfree
usb: option: add ZD Incorporated HSPA modem
usb: ch9: fix up MaxStreams helper
USB: usb-skeleton.c: cleanup open_count
USB: usb-skeleton.c: fix open/disconnect race
xhci: Properly handle COMP_2ND_BW_ERR
USB: remove dead code from suspend/resume path
USB: add quirk for another camera
drivers: usb: wusbcore: Fix dependency for USB_WUSB
xhci: Better debugging for critical host errors.
xhci: Be less verbose during URB cancellation.
xhci: Remove debugging about ring structure allocation.
xhci: Remove debugging about toggling cycle bits.
xhci: Remove debugging for individual transfers.
...
|
|
the feature to fix an oops
Echo vendor and product number of a non usb-storage device to
usb-storage driver's new_id, then plug in the device to host and you
will find following oops msg, the root cause is usb_stor_probe1()
refers invalid id entry if giving a dynamic id, so just disable the
feature.
[ 3105.018012] general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC
[ 3105.018062] CPU 0
[ 3105.018075] Modules linked in: usb_storage usb_libusual bluetooth
dm_crypt binfmt_misc snd_hda_codec_analog snd_hda_intel snd_hda_codec
snd_hwdep hp_wmi ppdev sparse_keymap snd_pcm snd_seq_midi snd_rawmidi
snd_seq_midi_event snd_seq snd_timer snd_seq_device psmouse snd
serio_raw tpm_infineon soundcore i915 snd_page_alloc tpm_tis
parport_pc tpm tpm_bios drm_kms_helper drm i2c_algo_bit video lp
parport usbhid hid sg sr_mod sd_mod ehci_hcd uhci_hcd usbcore e1000e
usb_common floppy
[ 3105.018408]
[ 3105.018419] Pid: 189, comm: khubd Tainted: G I 3.2.0-rc7+
#29 Hewlett-Packard HP Compaq dc7800p Convertible Minitower/0AACh
[ 3105.018481] RIP: 0010:[<ffffffffa045830d>] [<ffffffffa045830d>]
usb_stor_probe1+0x2fd/0xc20 [usb_storage]
[ 3105.018536] RSP: 0018:ffff880056a3d830 EFLAGS: 00010286
[ 3105.018562] RAX: ffff880065f4e648 RBX: ffff88006bb28000 RCX: 0000000000000000
[ 3105.018597] RDX: ffff88006f23c7b0 RSI: 0000000000000001 RDI: 0000000000000206
[ 3105.018632] RBP: ffff880056a3d900 R08: 0000000000000000 R09: ffff880067365000
[ 3105.018665] R10: 00000000000002ac R11: 0000000000000010 R12: ffff6000b41a7340
[ 3105.018698] R13: ffff880065f4ef60 R14: ffff88006bb28b88 R15: ffff88006f23d270
[ 3105.018733] FS: 0000000000000000(0000) GS:ffff88007a200000(0000)
knlGS:0000000000000000
[ 3105.018773] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[ 3105.018801] CR2: 00007fc99c8c4650 CR3: 0000000001e05000 CR4: 00000000000006f0
[ 3105.018835] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 3105.018870] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[ 3105.018906] Process khubd (pid: 189, threadinfo ffff880056a3c000,
task ffff88005677a400)
[ 3105.018945] Stack:
[ 3105.018959] 0000000000000000 0000000000000000 ffff880056a3d8d0
0000000000000002
[ 3105.019011] 0000000000000000 ffff880056a3d918 ffff880000000000
0000000000000002
[ 3105.019058] ffff880056a3d8d0 0000000000000012 ffff880056a3d8d0
0000000000000006
[ 3105.019105] Call Trace:
[ 3105.019128] [<ffffffffa0458cd4>] storage_probe+0xa4/0xe0 [usb_storage]
[ 3105.019173] [<ffffffffa0097822>] usb_probe_interface+0x172/0x330 [usbcore]
[ 3105.019211] [<ffffffff815fda67>] driver_probe_device+0x257/0x3b0
[ 3105.019243] [<ffffffff815fdd43>] __device_attach+0x73/0x90
[ 3105.019272] [<ffffffff815fdcd0>] ? __driver_attach+0x110/0x110
[ 3105.019303] [<ffffffff815fb93c>] bus_for_each_drv+0x9c/0xf0
[ 3105.019334] [<ffffffff815fd6c7>] device_attach+0xf7/0x120
[ 3105.019364] [<ffffffff815fc905>] bus_probe_device+0x45/0x80
[ 3105.019396] [<ffffffff815f98a6>] device_add+0x876/0x990
[ 3105.019434] [<ffffffffa0094e42>] usb_set_configuration+0x822/0x9e0 [usbcore]
[ 3105.019479] [<ffffffffa00a3492>] generic_probe+0x62/0xf0 [usbcore]
[ 3105.019518] [<ffffffffa0097a46>] usb_probe_device+0x66/0xb0 [usbcore]
[ 3105.019555] [<ffffffff815fda67>] driver_probe_device+0x257/0x3b0
[ 3105.019589] [<ffffffff815fdd43>] __device_attach+0x73/0x90
[ 3105.019617] [<ffffffff815fdcd0>] ? __driver_attach+0x110/0x110
[ 3105.019648] [<ffffffff815fb93c>] bus_for_each_drv+0x9c/0xf0
[ 3105.019680] [<ffffffff815fd6c7>] device_attach+0xf7/0x120
[ 3105.019709] [<ffffffff815fc905>] bus_probe_device+0x45/0x80
[ 3105.021040] usb usb6: usb auto-resume
[ 3105.021045] usb usb6: wakeup_rh
[ 3105.024849] [<ffffffff815f98a6>] device_add+0x876/0x990
[ 3105.025086] [<ffffffffa0088987>] usb_new_device+0x1e7/0x2b0 [usbcore]
[ 3105.025086] [<ffffffffa008a4d7>] hub_thread+0xb27/0x1ec0 [usbcore]
[ 3105.025086] [<ffffffff810d5200>] ? wake_up_bit+0x50/0x50
[ 3105.025086] [<ffffffffa00899b0>] ? usb_remote_wakeup+0xa0/0xa0 [usbcore]
[ 3105.025086] [<ffffffff810d49b8>] kthread+0xd8/0xf0
[ 3105.025086] [<ffffffff81939884>] kernel_thread_helper+0x4/0x10
[ 3105.025086] [<ffffffff8192a8c0>] ? _raw_spin_unlock_irq+0x50/0x80
[ 3105.025086] [<ffffffff8192b1b4>] ? retint_restore_args+0x13/0x13
[ 3105.025086] [<ffffffff810d48e0>] ? __init_kthread_worker+0x80/0x80
[ 3105.025086] [<ffffffff81939880>] ? gs_change+0x13/0x13
[ 3105.025086] Code: 00 48 83 05 cd ad 00 00 01 48 83 05 cd ad 00 00
01 4c 8b ab 30 0c 00 00 48 8b 50 08 48 83 c0 30 48 89 45 a0 4c 89 a3
40 0c 00 00 <41> 0f b6 44 24 10 48 89 55 a8 3c ff 0f 84 b8 04 00 00 48
83 05
[ 3105.025086] RIP [<ffffffffa045830d>] usb_stor_probe1+0x2fd/0xc20
[usb_storage]
[ 3105.025086] RSP <ffff880056a3d830>
[ 3105.060037] hub 6-0:1.0: hub_resume
[ 3105.062616] usb usb5: usb auto-resume
[ 3105.064317] ehci_hcd 0000:00:1d.7: resume root hub
[ 3105.094809] ---[ end trace a7919e7f17c0a727 ]---
[ 3105.130069] hub 5-0:1.0: hub_resume
[ 3105.132131] usb usb4: usb auto-resume
[ 3105.132136] usb usb4: wakeup_rh
[ 3105.180059] hub 4-0:1.0: hub_resume
[ 3106.290052] usb usb6: suspend_rh (auto-stop)
[ 3106.290077] usb usb4: suspend_rh (auto-stop)
Signed-off-by: Huajun Li <huajun.li.lee@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The current implementation of set_freezable_with_signal() is buggy and
tricky to get right. usb-storage is the only user and its use can be
avoided trivially.
All usb-storage wants is to be able to sleep with timeout and get
woken up if freezing() becomes true. This can be trivially
implemented by doing interruptible wait w/ freezing() included in the
wait condition. There's no reason to use set_freezable_with_signal().
Perform interruptible wait on freezing() instead of using
set_freezable_with_signal(), which is scheduled for removal.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Seth Forshee <seth.forshee@canonical.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Scanning cannot be run during suspend or hibernation, but if
usb-stor-scan freezes another thread waiting on scanning to
complete may fail to freeze.
However, if usb-stor-scan is left freezable without ever actually
freezing then the freezer will wait on it to exit, and threads
waiting for scanning to finish will no longer be blocked. One
problem with this approach is that usb-stor-scan has a delay to
wait for devices to settle (which is currently the only point where
it can freeze). To work around this we can request that the freezer
send a fake signal when freezing, then use interruptible sleep to
wake the thread early when freezing happens.
To make this happen, the following changes are made to
usb-stor-scan:
* Use set_freezable_with_signal() instead of set_freezable() to
request a fake signal when freezing
* Use wait_event_interruptible_timeout() instead of
wait_event_freezable_timeout() to avoid freezing
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Some USB mass-storage devices have bugs that cause them not to handle
the first READ(10) command they receive correctly. The Corsair
Padlock v2 returns completely bogus data for its first read (possibly
it returns the data in encrypted form even though the device is
supposed to be unlocked). The Feiya SD/SDHC card reader fails to
complete the first READ(10) command after it is plugged in or after a
new card is inserted, returning a status code that indicates it thinks
the command was invalid, which prevents the kernel from retrying the
read.
Since the first read of a new device or a new medium is for the
partition sector, the kernel is unable to retrieve the device's
partition table. Users have to manually issue an "hdparm -z" or
"blockdev --rereadpt" command before they can access the device.
This patch (as1470) works around the problem. It adds a new quirk
flag, US_FL_INVALID_READ10, indicating that the first READ(10) should
always be retried immediately, as should any failing READ(10) commands
(provided the preceding READ(10) command succeeded, to avoid getting
stuck in a loop). The patch also adds appropriate unusual_devs
entries containing the new flag.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Sven Geggus <sven-usbst@geggus.net>
Tested-by: Paul Hartman <paul.hartman+linux@gmail.com>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
CC: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Commits ae38c78a03e1b77ad45248fcf097e4568e740209
and 00914025cc4e783d4703b4db1d47b41f389e50c8 added quirk flags
US_FL_NO_READ_DISC_INFO and US_FL_NO_READ_CAPACITY_16 to
the usb-storage driver. However they did not add the corresponding flags
to adjust_quirks() in usb.c, so there was no facility for a user
to over-ride/add them via the quirks module parameter.
Signed-off-by: Karl Relton <karllinuxtest.relton@ntlworld.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This commit changes prefix for some of the USB mass storage
class related macros (ie. USB_SC_ for subclass and USB_PR_
for class).
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1400) adds runtime-PM support to usb-storage. It
utilizes the SCSI layer's runtime-PM implementation, so its scope is
limited. Currently the only effect is that disk-like devices (such as
card readers or flash drives) will be autosuspended if they aren't
mounted and their device files aren't open. This would apply, for
example, to card readers that don't contain a memory card.
Unfortunately this won't interact very well with the removable-media
polling normally carried out by hal or DeviceKit. Maybe those
programs can be changed to use a longer polling interval, or maybe the
default autosuspend time for usb-storage should be set to something
below 1 second.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: James Bottomley <James.Bottomley@suse.de>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Right now quirks are printed only when the are manually overriden with
the module parameters. It's not so useful to remind the user that his
parameters are correctly applied; what is useful is to print out the
quirks the user is not aware are being applied.
So let's do the smart thing and print the quirks when they are present.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Use pr_foo and dev_foo instead of printk. Maybe US_DEBUG* should be
replaced too.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
For more clearance what the functions actually do,
usb_buffer_alloc() is renamed to usb_alloc_coherent()
usb_buffer_free() is renamed to usb_free_coherent()
They should only be used in code which really needs DMA coherency.
All call sites have been changed accordingly, except for staging
drivers.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Pedro Ribeiro <pedrib@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1350) removes all usages of coherent buffers for USB
control-request setup-packet buffers. There's no good reason to
reserve coherent memory for these things; control requests are hardly
ever used in large quantity (the major exception is firmware
transfers, and they aren't time-critical). Furthermore, only seven
drivers used it. We might as well always use streaming DMA mappings
for setup-packet buffers, and remove some extra complexity from
usbcore.
The DMA-mapping portion of hcd.c is currently in flux. A separate
patch will be submitted to remove support for URB_NO_SETUP_DMA_MAP
after everything else settles down. The removal should go smoothly,
as by then nobody will be using it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The five-second delay can be rather annoying, and makes the system
appear much less responsive when you connect a USB drive.
It's also not entirely clear that it is needed - the settling delay has
at least historically been an issue on some Apple iPods, for example,
and some devices have been reported to need even more than the old 5s
delay.
But before we penalize them all, let's see how bad it really is. Some
of the reasons for long delays seem to be actual historical kernel bugs
that should probably never have been papered over with a delay in the
first place (there's a Ubuntu bug report for 2.6.20 about a NULL pointer
dereference unless 'delay_use' is 8 or more, for example).
It also looks like some distros have already shipped with delay_use=0,
so the five second default may well be totally historical.
In other words: "Let's see if anybody screams".
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch adds a mask bit which was mistakenly omitted from the
as1311 patch (usb-storage: add BAD_SENSE flag).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1312) fixes a minor bug in usb-storage. The
fill_inquiry() routine neglects to pre-load the inquiry data buffer
with spaces. As a result, if the vendor name is shorter than 8
characters or the product name is shorter than 16, the remainder will
be filled with garbage.
The patch also removes some unnecessary calls to strlen().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1311) fixes a problem in usb-storage: Some devices are
pretty broken when it comes to reporting sense data. The information
they send back indicates that they have more than 18 bytes of sense
data available, but when the system asks for more than 18 they fail or
hang. The symptom is that probing fails with multiple resets.
The patch adds a new BAD_SENSE flag to indicate that usb-storage
should never ask for more than 18 bytes of sense data. The flag can
be set in an unusual_devs entry or via the "quirks=" module parameter,
and it is set automatically whenever a REQUEST SENSE command for more
than 18 bytes fails or times out.
An unusual_devs entry is added for the Agfa photo frame, which uses a
Prolific chip having this bug.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Daniel Kukula <daniel.kuku@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The WHCI HCD will also support urbs with scatter-gather lists. Add a
usb_bus field to indicated how many sg list elements are supported by
the HCD. Use this to decide whether to pass the scatter-list to the HCD
or not.
Make the usb-storage driver use this new field.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Use dev_dbg() instead of an unconditional printk(KERN_DEBUG). This has
two benefits; one is that it identifies the USB device which the messages
related to, and the other is that the messages won't be produced unless
debug is turned on.
Enable the debug messages when CONFIG_USB_STORAGE_DEBUG is set.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Instead of reporting "SCSI emulation for USB Mass Storage devices",
report "usb-storage 1-4:1.0".
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1217) converts usb-storage's onetouch subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1216) converts usb-storage's karma subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1215) converts usb-storage's alauda subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1214) converts usb-storage's jumpshot subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1213) converts usb-storage's datafab subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1212) converts usb-storage's freecom subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
