| Age | Commit message (Collapse) | Author |
|---|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
net/mac80211/main.c
|
|
Ignore ADSL routers, which can have the same vendor and product IDs
as ADSL modems but should be handled by the cx82310_eth driver.
This intentionally ignores device IDs that aren't currently handled
by cx82310_eth. There may be other device IDs that perhaps shouldn't
be claimed by cxacru.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added the 0xDAF8 to 0xDAFF PID range for ChamSys limited USB interface/wing products
Signed-off-by: Luke Lowrey <luke@chamsys.co.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
descriptors.
Certain USB devices, such as the Nokia X6 mobile phone, don't expose any
endpoint descriptors on some of their interfaces. If the ACM driver is forced
to probe all interfaces on a device the a NULL pointer dereference will occur
when the ACM driver attempts to use the endpoint of the alternative settings.
One way to get the ACM driver to probe all the interfaces is by using the
/sys/bus/usb/drivers/cdc_acm/new_id interface.
This patch checks that the endpoint pointer for the current alternate settings
is non-NULL before using it.
Signed-off-by: Toby Gray <toby.gray@realvnc.com>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
cdc-acm.c : Manage pseudo-modem without AT commands capabilities
Enable to drive electronic simple gadgets based on microcontrolers.
The Interface descriptor is like this:
bInterfaceClass 2 Communications
bInterfaceSubClass 2 Abstract (modem)
bInterfaceProtocol 0 None
Signed-off-by: Philippe Corbes <philippe.corbes@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The command endpoint is either a bulk or interrupt endpoint, but using
the wrong type of transfer causes an error if CONFIG_USB_DEBUG is
enabled after commit f661c6f8c67bd55e93348f160d590ff9edf08904, which
checks for this mismatch.
Detect which type of endpoint it is and use a bulk/int URB as
appropriate. There are other function calls specifying a bulk pipe,
but usb_clear_halt doesn't use the pipe type (only the endpoint) and
usb_bulk_msg auto-detects interrupt transfers.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: stable <stable@kernel.org> [.34 and newer]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Add the USB IDs needed to support the B&B USOPTL4-4P, USO9ML2-2P, and
USO9ML2-4P. This patch expands and corrects a typo in the patch sent
on 08-31-2010.
Signed-off-by: Dave Ludlow <dave.ludlow@bay.ws>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Samsung phones
S60 phones from Nokia and Samsung expose two ACM channels. The first is a modem
with a standard AT-command interface, which is picked up correctly by CDC-ACM.
The second ACM port is marked as having a vendor-specific protocol. This means
that the ACM driver will not claim the second channel by default.
This adds support for the second ACM channel for the following devices:
Nokia E63
Nokia E75
Nokia 6760 Slide
Nokia E52
Nokia E55
Nokia E72
Nokia X6
Nokia N97 Mini
Nokia 5800 Xpressmusic
Nokia E90
Samsung GTi8510 (INNOV8)
Signed-off-by: Toby Gray <toby.gray@realvnc.com>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Add the USB ID needed to support B&B Electronic's 2-port, optically-isolated,
powered, USB to RS485 converter.
Signed-off-by: Dave Ludlow <dave.ludlow@bay.ws>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Remove the hard coding of the debug flag to 1.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
When using the remove sysfs file, the device configuration is set to -1
(unconfigured). This eventually unbind drivers with the bandwidth_mutex
held. Some drivers may call functions that hold said mutex, like
usb_reset_device. This is the case for rtl8187, for example. This will
lead to the same process holding the mutex twice, which deadlocks.
Besides, according to Alan Stern:
"The deadlock problem probably could be handled somehow, but there's a
separate issue: Until the usb_disable_device call finishes unbinding
the drivers, the drivers are free to continue using their allocated
bandwidth. We musn't change the bandwidth allocations until after the
unbinding is done. So this patch is indeed necessary."
Unbinding the driver before holding the bandwidth_mutex solves the
problem. If any operation after that fails, drivers are not bound again.
But that would be a problem anyway that the user may solve resetting the
device configuration to one that works, just like he would need to do in
most other failure cases.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The Pirelli DP-L10 mobile is sold under various brand names. One, already
supported by cp210x, is the T-COM TC300. Here is the lsusb for that version:
-------------------------------------------------------------------
Bus 001 Device 002: ID 0489:e000 Foxconn / Hon Hai T-Com TC 300
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0489 Foxconn / Hon Hai
idProduct 0xe000 T-Com TC 300
bcdDevice 1.00
iManufacturer 1 Silicon Labs
iProduct 2 TC 300
iSerial 3 0001
[snip]
---------------------------------------------------------------------------
However the native Pirelli DP-L10 is not supported:
------------------------------------------------------------------
Bus 001 Device 003: ID 0489:e003 Foxconn / Hon Hai Pirelli DP-L10
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0489 Foxconn / Hon Hai
idProduct 0xe003 Pirelli DP-L10
bcdDevice 1.00
iManufacturer 1 Silicon Labs
iProduct 2 DP-L10
iSerial 3 0001
[snip]
-------------------------------------------------------------------------
All that is required is an extra USB_DEVICE entry:
{ USB_DEVICE(0x0489, 0xE003) }, /* Pirelli Broadband S.p.A, DP-L10 SIP/GSM
+Mobile */
The patch adds that entry. Tested under 2.6.36-rc2 from git.
Signed-off-by: A E Lawrence <lawrence_a_e@ntlworld.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This is the cable between an H3000 navigation unit and a multi-function display.
http://www.bandg.com/en/Products/H3000/Spares-and-Accessories/Cables/H3000-CPU-USB-Cable-Pack/
Signed-off-by: Jason Detring <jason.detring@navico.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
New device ID added for Balluff RFID reader.
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Unfortunately some of the hardware PID belonging to auto-install CDROM
(AICD) of Novatel modems found their way into the option module. This
causes the AICD to be treated as a modem in stead of a disk. Since the
modem ports do not appear until after the AICD is ejected, this
essentially disables the modem. After a couple of minutes the AICD
should auto-eject, but it is just too long a wait. The frequency of the
failure seems to depend on both the hardware and the linux distribution.
Here is a patch that fixes this up, and also adds a couple of new PID,
offering some explanations and removing some incomplete and unnecessary
comments.
Signed-off-by: Dirk De Schepper <ddeschepper@nvtl.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Please find attached patch for
https://bugzilla.kernel.org/show_bug.cgi?id=16023 problem.
Signed-off-by: Maxim Osipov <maxim.osipov@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch removes the following section mismatch warning,
by moving the function rndis_init() from .init.text to .text.
WARNING: vmlinux.o(.text+0x1aeca5a): Section mismatch in reference from the function rndis_bind_config() to the function .init.text:rndis_init()
The function rndis_bind_config() references
the function __init rndis_init().
This is often because rndis_bind_config lacks a __init
annotation or the annotation of rndis_init is wrong.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The iounmap(ehci->ohci_hcctrl_reg); should be the first thing we do
because the ioremap() was the last thing we did. Also if we hit any of
the goto statements in the original code then it would have led to a
NULL dereference of "ehci". This bug was introduced in: 796bcae7361c
"USB: powerpc: Workaround for the PPC440EPX USBH_23 errata [take 3]"
I modified the few lines in front a little so that my code didn't
obscure the return success code path.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
DEBUG is defined unconditionally, remove it as this clutters the message log.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: pxa27x_keypad - remove input_free_device() in pxa27x_keypad_remove()
Input: mousedev - fix regression of inverting axes
Input: uinput - add devname alias to allow module on-demand load
Input: hil_kbd - fix compile error
USB: drop tty argument from usb_serial_handle_sysrq_char()
Input: sysrq - drop tty argument form handle_sysrq()
Input: sysrq - drop tty argument from sysrq ops handlers
|
|
Add ftdi product ID for Lenz LI-USB, a model train interface. This
was NOT tested against 2.6.35, but a similar patch was tested with the
CentOS 2.6.18-194.11.1.el5 kernel. It wasn't clear to me what
ordering is being used in ftdi_sio.c, so I inserted the ID after another
model train entry(SPROG_II).
Signed-off-by: Galen Seitz <galens@seitzassoc.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
copy_to_user() returns number of not copied bytes, not error code.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
copy_to_user() returns number of not copied bytes, not error code.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch fixes a isoc transfer bug reported by Sander Eikelenboom.
When ep->skip is set, endpoint ring dequeue pointer should be updated
when processed every missed td. Although ring dequeue pointer will also
be updated when ep->skip is clear, leave it intact during missed tds
processing may cause two issues:
1). If the very next valid transfer following missed tds is a short
transfer, its actual_length will be miscalculated;
2). If there are too many missed tds during transfer, new inserted tds
may found the transfer ring full and urb enqueue fails.
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The code to increment the TRB pointer has a slight ambiguity that could
lead to a bug on different compilers. The ANSI C specification does not
specify the precedence of the assignment operator over the postfix
operator. gcc 4.4 produced the correct code (increment the pointer and
assign the value), but a MIPS compiler that one of John's clients used
assigned the old (unincremented) value.
Remove the unnecessary assignment to make all compilers produce the
correct assembly.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Add the ID for the Ionics PlugComputer (<http://ionicsplug.com/>).
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
If the write download record failed we shouldn't return 0.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The reset state of twl4030-usb is not sleeping, it starts
up awaken and we need to disable it if we have booted
with a disconnected cable to avoid over consumption on
the default state.
To avoid problems later, we read the current state of the
transceiver from the PHY_PWR_CTRL register. The bootloader
can, anyways, put the device to sleep before us.
Tested on a custom OMAP board.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
In this code, 0 is returned on memory allocation failure, even though other
failures return -ENOMEM or other similar values.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression ret;
expression x,e1,e2,e3;
@@
ret = 0
... when != ret = e1
*x = \(kmalloc\|kcalloc\|kzalloc\)(...)
... when != ret = e2
if (x == NULL) { ... when != ret = e3
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Warning(include/linux/usb/composite.h:284): No description found for parameter 'disconnect'
Warning(drivers/usb/gadget/composite.c:744): No description found for parameter 'c'
Warning(drivers/usb/gadget/composite.c:744): Excess function parameter 'cdev' description in 'usb_string_ids_n'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
flag was never set in ssu100_process_packet. Add logic to set it
before calling tty_insert_flip_*
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Add a disconnect function to the functions of this device. The
disconnect is a call to usb_serial_generic_disconnect() so it requires
that symbol to be exported from generic.c.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This is needed by the ssu100 driver to use this function.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Rework the logic for TIOCMIWAIT to use wait_event_interruptible.
This also adds support for TIOCGICOUNT.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The function ssu100_setregister was hard coded to only set the MCR
register. Add a register parameter so that other registers can be
set.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The ssu100 uses a TI16C550C UART so the SERIAL_ defines in this code
are duplicates of those found in serial_reg.h. Remove the defines in
ssu100.c and use the ones in the header file.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The status information does not appear at the start of each incoming
packet so the check for len < 4 at the start of ssu100_process_packet
is wrong. Remove it.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
If we can't read the firmware for a device from the disk, and yet the
device already has a valid firmware image in it, we don't want to
replace the firmware with something invalid. So check the version
number to be less than the current one to verify this is the correct
thing to do.
Reported-by: Chris Beauchamp <chris@chillibean.tv>
Tested-by: Chris Beauchamp <chris@chillibean.tv>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The USB max packet size (always little-endian) was not being byte
swapped on big-endian systems.
Applicable since [USB: ftdi_sio: fix hi-speed device packet size calculation] approx 2.6.31
Signed-off-by: Michael Wileczka <mikewileczka@yahoo.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The definitions for BREAK_ON and BREAK_OFF are inverted, causing break
requests to fail. This patch sets BREAK_ON and BREAK_OFF to the correct
values.
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Add support for the Zeagle N2iTiON3 dive computer interface. Since
Zeagle devices are actually manufactured by Seiko, this patch will
support other Seiko based models as well.
Signed-off-by: Jef Driesen <jefdriesen@telenet.be>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The patch with title below makes reference count of usb serial module
always more than one after driver is bound.
USB-BKL: Remove BKL use for usb serial driver probing
In fact, the patch above only replaces lock_kernel() with try_module_get()
, and does not use module_put() to do what unlock_kernel() did, so casue leak
of reference count of usb serial module and the module can not be unloaded
after serial driver is bound with device.
This patch fixes the issue, also simplifies such things:
-only call try_module_get() once in the entry of usb_serial_probe()
-only call module_put() once in the exit of usb_serial_probe
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
I recently bought a i-gotU USB GPS, and whilst hunting around for linux
support discovered this post by you back in 2009:
http://kerneltrap.org/mailarchive/linux-usb/2009/3/12/5148644
>Try the navman driver instead. You can either add the device id to the
> driver and rebuild it, or do this before you plug the device in:
> modprobe navman
> echo -n "0x0df7 0x0900" > /sys/bus/usb-serial/drivers/navman/new_id
>
> and then plug your device in and see if that works.
I can confirm that the navman driver works with the right device IDs on
my i-gotU GT-600, which has the same device IDs. Attached is a patch
adding the IDs.
From: Ross Burton <ross@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The ISP1760 has some timing requirements where it has to delay a short
period after a write to a register has started. However, this delay is
from the time the write hits the USB chip (the ISP1760), not from the
time where the processor started processing the write. So on a quick
enough processor, it is sometimes possible for the write to not hit the
device before we start delaying, and we then violate the part's timing
requirements, so things stop working.
To avoid all this, insert a write barrier after the register write and
before the timing delay/register read so we can guarantee we only start
counting time after the write has hit the device.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
We're trying to test for the the end of the loop here. "format" is
never NULL. We don't know what "format->fcc" is because we're past the
end of the loop and I think "fmt->fmt.pix.pixelformat" comes from the
user so we don't know what that is either. It works, but it's cleaner
to just test to see if (i == ARRAY_SIZE(uvc_formats).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Since handle_sysrq() does not take tty as argument anymore we can
drop it from usb_serial_handle_sysrq_char() as well.
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Sysrq operations do not accept tty argument anymore so no need to pass
it to us.
[Stephen Rothwell <sfr@canb.auug.org.au>: fix build breakage in drm code
caused by sysrq using bool but not including linux/types.h]
[Sachin Sant <sachinp@in.ibm.com>: fix build breakage in s390 keyboadr
driver]
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
