Age | Commit message (Collapse) | Author |
|
In its current state, the ux500-musb driver uses platform data pointers
blindly with no prior checking. If no platform data pointer is passed
this will Oops the kernel. In this patch we ensure platform data and
board data are present prior to using them.
Cc: linux-usb@vger.kernel.org
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The dma_mask will always be the same as the coherent_dma_mask, so let's
cut down on the platform_data burden and set it as such in the driver.
This also saves us from supporting it separately when we come to enable
this driver for Device Tree.
Cc: linux-usb@vger.kernel.org
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The MUSB HDRC configuration never changes between each of the ux500
supported platforms, so there's little point passing it though platform
data. If we set it in the driver instead, we can make good use of it
when booting with either ATAGs or Device Tree.
Cc: linux-usb@vger.kernel.org
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
For all ux500 based platforms the maximum number of end-points are used.
Move this knowledge into the driver so we can relinquish the burden from
platform data. This also removes quite a bit of complexity from the driver
and will aid us when we come to enable the driver for Device Tree.
Cc: linux-usb@vger.kernel.org
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
My PL2303HX works at 500kbps after applying this patch.
I suppose that it could work at other non standard speeds since this fix
"correctly handle baudrates above 115200"
https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/drivers/usb/serial/pl2303.c?id=8d48fdf689fed2c73c493e5146d1463689246442
came after this one
"fix baud rate handling in case of unsupported values"
https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/drivers/usb/serial/pl2303.c?id=25b8286805e856c8c7fda127018e31032c918015
but I only can test it with 500000.
Patch made against mainline but tested with 3.4.45
Signed-off-by: Luca Olivetti <luca@ventoso.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The "runtime idle" helper routine, rpm_idle(), currently ignores
return values from .runtime_idle() callbacks executed by it.
However, it turns out that many subsystems use
pm_generic_runtime_idle() which checks the return value of the
driver's callback and executes pm_runtime_suspend() for the device
unless that value is not 0. If that logic is moved to rpm_idle()
instead, pm_generic_runtime_idle() can be dropped and its users
will not need any .runtime_idle() callbacks any more.
Moreover, the PCI, SCSI, and SATA subsystems' .runtime_idle()
routines, pci_pm_runtime_idle(), scsi_runtime_idle(), and
ata_port_runtime_idle(), respectively, as well as a few drivers'
ones may be simplified if rpm_idle() calls rpm_suspend() after 0 has
been returned by the .runtime_idle() callback executed by it.
To reduce overall code bloat, make the changes described above.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
|
|
This patch adds an ohci->priv field for private use by OHCI
platform drivers.
Until now none of the platform drivers has used this private space,
but that's about to change in the next patch of this series.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch splits the ohci-platform code from ohci-hcd out
into its own separate driver module.This work is part of enabling
multi-platform kernels on ARM.
In V2:
-Passed "hcd" argument instead of "ohci" in ohci_setup() because it is
using "struct usb_hcd" argument.
In V3:
-Directly passed "hcd" argument not required to call ohci_to_hcd() function.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pci_enable_device() will set device power state to D0,
so it's no need to do it again in ci13xxx_pci_probe().
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The usb3503 driver sleeps a flat 100ms when resetting the chip, with a
comment about waiting for the reference clock. This seems to be a
board-specific detail that should not hold up boot across all platforms.
This patch reduces the sleep to the 4ms initialization delay that the
chip itself actually requires (as per its data sheet). If certain boards
require more time to set up the reference clock, they should change this
through local patches or add a proper, configurable synchronization
mechanism.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove an erroneous tab that should be a space.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds Wireless USB root hub support to the USB HCD. It allows
the HWA to create its root hub which previously failed because the HCD
treated wireless root hubs the same as USB2 high speed hubs. The creation
of the root hub would fail in that case due to lack of TTs which wireless
root hubs do not support.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove redundant "_fusbh200_" from fusbh200_hcd_fusbh200_probe
and fusbh200_hcd_fusbh200_remove
Signed-off-by: Yuan-Hsin Chen <yhchen@faraday-tech.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If you want to download Infineon modem via USB, this Infineon USB
flashloader driver is required.
Signed-off-by: Wei Shuai <cpuwolf@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Option GTM681W uses a qualcomm chip and can be
served by the qcserial device driver.
Signed-off-by: Richard Weinberger <richard@nod.at>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The patch adds a new HIDCOM device and does not affect other devices
driven by the cypress_M8 module. Changes are:
- add VendorID ProductID to device tables
- skip unstable speed check because FRWD uses 115200bps
- skip reset at probe which is an issue workaround for this
particular device.
Signed-off-by: Robert Butora <robert.butora.fi@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Addition of the M and N recommended values for the USB3 PHY DPLL.
Sysclk for DRA7xx is 20MHz.
This yields:
Clk = 20MHz * M/(N+1) = 20MHz * 1000 /(7+1) = 2.5 Ghz
Signed-off-by: Ruchika Kharwar <ruchika@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Pci_enable_device() will set device power state to D0,
so it's no need to do it again in dwc3_pci_probe().
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch splits the PCI portion of ohci-hcd out into its
own separate driver module, called ohci-pci.
The major point of difficulty lies in ohci-pci's many vendor- and
device-specific workarounds. Some of them have to be applied before
calling ohci_start() some after, which necessitates a fair amount of
code motion. The other platform drivers require much smaller changes.
The complete sb800_prefetch() function moved to ohci-q.c,because its
only related to ohci-pci driver.
USB_OHCI_HCD_PCI symbol no longer dependence on STB03xxx, PPC_MPC52xx and
USB_OHCI_HCD_PPC_OF that's what removed.
V2:
- few specific content of pci related code in ohci_pci_start function has been moved to ohci_pci_reset
and rest of the generic code is written in ohci_start of ohci-hcd.c file.
V3:
- ohci_restart() has been called in ohci_pci_reset() function for to reset the ohci pci.
V4:
-sb800_prefetch() moved to ohci-q.c,because its only related to ohci-pci.
-no longer _creating_ CONFIG_USB_OHCI_PCI,creating CONFIG_USB_OHCI_HCD_PCI.
-overrides renamed with pci_override,its giving proper meaning.
V5:
-sb800_prefetch() moved to pci-quirks.c,because its only related to pci.
V6:
-sb800_prefetch() function has been moved to pci-quirks.c made as separate patch in 2/3.
-Most of the generic ohci pci changes moved in 2/3 patch,now this is complete ohci-pci separation patch.
V7:
-Unrelated include file has been removed from ohci.h file.
V8:
-USB_OHCI_HCD_PCI symbol does not dependence on STB03xxx, PPC_MPC52xx and USB_OHCI_HCD_PPC_OF.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Note that this changes is part of separating the ohci pci host controller
driver from ohci-hcd host code.
This contains :
-Moved sb800_prefetch() function from ohci-pci.c to pci-quirks.c file
and EXPORTed, this is part of the effort to move the ohci pci related
code to generic pci code.
-Passed "device" argument instead of "ohci_hcd" in sb800_prefetch()
function to avoid extra include file in pci-quirks.c.
V2:
-Passed "device" argment instead of "pci_dev", then we use to_pci_dev()
to get the "pci_dev" structure.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch prepares ohci-hcd for being split up into a core
library and separate platform driver modules. A generic
ohci_hc_driver structure is created, containing all the "standard"
values, and a new mechanism is added whereby a driver module can
specify a set of overrides to those values. In addition the
ohci_restart(),ohci_suspend() and ohci_resume() routines need
to be EXPORTed for use by the drivers.
Added ohci_setip(() and ohci_start() routine for to start the generic
controller rather than each having its own idiosyncratic approach.
This allow to clean duplicated code in most of SOC driver
In V2:
-ohci_hcd_init() ohci_run() and ohci_stop() are not made non-static.
-Adds the ohci_setup() and ohci_start() routine.
In V3:
-purpose of ohci_setup() and ohci_start() function description written in the patch
description.
-ohci_init() are not made non-static but now called beginning of the ohci_restart().
-ohci_run() signature change reverted back.
-unrelated changes removed.
-duplicate comment line removed.
-inline ohci_suspend() and ohci_resume() is not needed so removed from ohci.h file.
In V4:
-ohci-init() EXPORTed because it is called by all bus glue modules.
-ohci-setup() removed from 1/2 added into 2/2 patch.
In V5:
-Again ohci_setup() is added and EXPORTed because to replace the ohci_init() from
all bus glues.
-ohci_init() is not made non-static function.
In V6:
-ohci_init() call is removed from ohci_quirk_nec_worker(), because it is already called in ohci_restart().
In V8:
-ohci_hcd_init() is called by ohci_setup() to make generic ohci initialization in all ohci drivers.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch attempts to fix the isochronous API in the fhci-hcd
driver. There are two problems with the current code:
ed->last_iso is used but not set anywhere. The patch changes
its name to ed->next_iso and uses it to store the frame number
of the next available slot in the isochronous stream.
urb->start_frame isn't set when the URB_ISO_ASAP flag is off.
The patch sets it to the next available slot if the stream is
in use, or the current frame otherwise.
This won't give the right behavior when an underrun occurs, but I
don't know enough about the driver to handle that case.
Unfortunately, I don't have any way to test these changes.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Anton Vorontsov <avorontsov@ru.mvista.com>
CC: Li Yang <leoli@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch attempts to update the imx21-hcd driver to the current
standard for the isochronous API. Firstly, urb->start_frame should
always be set by the driver; it is not an input parameter. Secondly,
the URB_ISO_ASAP flag matters only when an URB is submitted to a
stream that has gotten an underrun. It causes the URB to be scheduled
for the next available slot in the future, rather than the earliest
unused (and expired) slot.
Unfortunately, I don't have any way to test these changes.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Sascha Hauer <kernel@pengutronix.de>
CC: Martin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch attempts to fix the isochonour API in the musb host
driver. In particular, the urb->start_frame field should always be
set by the driver; it isn't an input parameter.
The simplest way to accomplish this is to treat all URBs as though the
URB_ISO_ASAP flag was set. This won't give the right behavior when an
underrun occurs, but I don't know enough about the musb driver to
handle that case.
Unfortunately, I have no way to test this change.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Exynos5440 does not require any explict USB phy configuration. So skip
the USB phy configuration for Exynos5440 based platforms.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Ackked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is a specifier we may use to dump small buffers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Also, unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
'hcd' can never be NULL and the spear_ehci_hcd_drv_remove routine
will never be called in_interrupt. Hence remove these checks.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When converting this driver to devm_ioremap_resource, the removal of this now
unneeded function has been forgotten.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch is to add a property 'disabled-ports' representing the unused port
of USB3503. USB3503 can support up to 3 USB host port and each ports can be
controlled to be enabled or disabled. Do not describe this property if all
ports must be enabled.
You can represent the ports to disable in the device tree.
usb3503@08{
...
disabled-ports = <2 3>;
...
};
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch is to disable the USB ports unconnected to USB3503. In order to
disable the port, 'port_off_mask' must be set.
* Disable PORT1 only
.port_off_mask = USB3503_OFF_PORT1;
* Disable PORT1 and PORT3 only
.port_off_mask = USB3503_OFF_PORT1 | USB3503_OFF_PORT3;
* Enables all ports
.port_off_mask = 0;
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds some code that inadvertently got left out of commit
c1fdb68e3d73741630ca16695cf9176c233be7ed (USB: EHCI: changes related
to qh_refresh()). The calls to qh_refresh() and qh_link_periodic()
were taken out of qh_schedule(); therefore it is necessary to call
these routines manually after calling qh_schedule().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
very minor patch fixing the following build warning on
a debug message:
drivers/usb/musb/musb_host.c: In function ‘musb_host_rx’:
drivers/usb/musb/musb_host.c:1763:4: warning: format ‘%x’ \
expects argument of type ‘unsigned int’, but argument \
6 has type ‘dma_addr_t’ [-Wformat]
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Registered Tegra USB PHY as a separate platform driver.
To synchronize host controller and PHY initialization, used deferred
probe mechanism. As PHY should be initialized before EHCI starts running,
deferred probe of Tegra EHCI driver till PHY probe gets completed.
Got rid of instance number based handling in host driver.
Made use of DT params to get the PHY Pad registers.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Check return values from all GPIO APIs and handle errors accordingly.
Remove the call to clk_disable_unprepare(); this function does not
prepare or enable the clock, so the error path should not disable or
unprepare it.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
As GPIO information is avail through DT, used it to get Tegra ULPI
reset GPIO number. Added a new member to tegra_usb_phy structure to
store this number.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Added a new PHY mode to support OTG.
Obtained Tegra USB PHY mode using DT property.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
In case if clk_get_sys fails, return correct error value provided by
the API.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Increase the current arbitrary limit for isocronous packet size to a
value large enough to account for USB 3.0 super bandwidth streams,
bMaxBurst (0~15 allowed, 1~16 packets)
bmAttributes (bit 1:0, mult 0~2, 1~3 packets)
so the size max for one USB 3 isocronous transfer is
1024 byte * 16 * 3 = 49152 byte
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Federico Manzan <f.manzan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The control-message timeout is specified in milliseconds and should not
depend on HZ.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The control and bulk-message timeouts are specified in milliseconds and
should not depend on HZ.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The bulk-message timeout is specified in milliseconds and should not
depend on HZ.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The control-message timeout is specified in milliseconds and should not
depend on HZ.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix regression introduced by commit 0eafe4de1a ("USB: serial: mos7840:
add support for MCS7810 devices") which used stack-allocated buffers for
control messages.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The read_mos_reg function is called with stack-allocated buffers, which
must not be used for control messages.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix regression introduced by commit 214916f2e ("USB: visor: reimplement
using generic framework") which broke initialisation of Treo/Kyocera
devices that re-mapped bulk-in endpoints.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The first and second interrupt-in urbs are swapped for some Treo/Kyocera
devices, but the urb context was never updated with the new port.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch reverts commit 3e619d04159be54b3daa0b7036b0ce9e067f4b5d
(USB: EHCI: fix bug in scheduling periodic split transfers). The
commit was valid -- it fixed a real bug -- but the periodic scheduler
in ehci-hcd is in such bad shape (especially the part that handles
split transactions) that fixing one bug is very likely to cause
another to surface. That's what happened in this case; the result was
choppy and noisy playback on certain 24-bit audio devices.
The only real fix will be to rewrite this entire section of code. My
next project...
This fixes https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1136110.
Thanks to Tim Richardson for extra testing and feedback, and to Joseph
Salisbury and Tyson Tan for tracking down the original source of the
problem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Joseph Salisbury <joseph.salisbury@canonical.com>
CC: Tim Richardson <tim@tim-richardson.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus
Sarah writes:
xhci: Misc bug fixes for 3.10.
Hi Greg,
Here's four xHCI bug fixes that should be queued for 3.10.
The first two are generic bug fixes, and have been in my queue for a while
because I've been doing the OPW internship coordination. I suspect you'll be
seeing more pull requests from me now that the intern selection process is
almost over. :)
The last two patches fix a nasty kernel crash on resume from S3 for TI hosts
that have the compliance mode quirk. Tony has confirmed that the patches fix
the issue on the effected systems.
All four patches are marked for stable.
Sarah Sharp
|
|
Since highmem PIO URB handling was introduced in:
8e8a551 usb: musb: host: Handle highmem in PIO mode
when a URB is being handled it may happen that the static use_sg flag
was set by a previous URB with buffer in highmem. This leads to error
in handling the present URB.
Fix this by making the use_sg flag URB specific.
Cc: stable <stable@vger.kernel.org> # 3.7+
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|