| Age | Commit message (Collapse) | Author |
|---|
|
There are also two allocations with GFP_KERNEL in the pre-/post_reset
code paths. That is no good because that is a part of the SCSI error handler.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
intfdata is set only after scsi_scan(). uas_pre_reset() however
needs intfdata to be valid and will follow the NULL pointer
killing khubd. intfdata must be preemptively set before the
host is registered and undone in the error case.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Quote Dan:
The patch e36e64930cff: "uas: Use GFP_NOIO rather then GFP_ATOMIC
where possible" from Nov 7, 2013, leads to the following static
checker warning:
drivers/usb/storage/uas.c:806 uas_eh_task_mgmt()
error: scheduling with locks held: 'spin_lock:lock'
Some other allocations under spinlock are not caught.
The fix essentially reverts e36e64930cffd94e1c37fdb82f35989384aa946b
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
By specifying NO_UNION_NORMAL the ACM driver does only use the first two
USB interfaces (modem data & control). The AT Port, Diagnostic and NMEA
interfaces are left to the USB serial driver.
Signed-off-by: Michael Ulbricht <michael.ulbricht@systec-electronic.com>
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Power control of hub ports target the CLEAR_FEATURE and SET_FEATURE
requests to ports, not to the hub. Fix the hub control function to
detect the request correctly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The ret variable is not initialized in all code paths of the
ohci_jz4740_hub_control function. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
To avoid memory fetch underflows with larger USB transfers, Tegra SoCs
need txfill_tuning's txfifothresh register field set to a non-default
value. Add a custom reset override in order to set this up.
These values are recommended practice for all Tegra chips. However,
I've only noticed practical problems when not setting them this way on
systems using Tegra124. Hence, CC: stable only for recent kernels which
actually support Tegra124.
Cc: <stable@vger.kernel.org> # 3.14+
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Patch 'b8efdaf USB: EHCI: add check for wakeup/suspend race'
adds a check for possible race between suspend and wakeup interrupt,
and thereby it returns -EBUSY as error code if there's a wakeup
interrupt.
So the platform host controller should not proceed further with
its suspend callback, rather should return immediately to avoid
powering down the essential things, like phy.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Patch 'b8efdaf USB: EHCI: add check for wakeup/suspend race'
adds a check for possible race between suspend and wakeup interrupt,
and thereby it returns -EBUSY as error code if there's a wakeup
interrupt.
So the platform host controller should not proceed further with
its suspend callback, rather should return immediately to avoid
powering down the essential things, like phy.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The code in hcd-pci.c that matches up EHCI controllers with their
companion UHCI or OHCI controllers assumes that the private drvdata
fields don't get set too early. However, it turns out that this field
gets set by usb_create_hcd(), before hcd-pci expects it, and this can
result in a crash when two controllers are probed in parallel (as can
happen when a new controller card is hotplugged).
The companions_rwsem lock was supposed to prevent this sort of thing,
but usb_create_hcd() is called outside the scope of the rwsem.
A simple solution is to check that the root-hub pointer has been
initialized as well as the drvdata field. This doesn't happen until
usb_add_hcd() is called; that call and the check are both protected by
the rwsem.
This patch should be applied to stable kernels from 3.10 onward.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Stefani Seibold <stefani@seibold.net>
Tested-by: Stefani Seibold <stefani@seibold.net>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If acm_submit_read_urbs() fails in acm_port_activate(), error handling
code calls usb_autopm_put_interface() while it is already called
before acm_submit_read_urbs(). The patch reorganizes error handling code
to avoid double decrement of USB interface's PM-usage counter.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
%s/addresssed/addressed
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix regression introduced by commit 8e493ca1767d ("USB: usb_wwan: fix
bulk-urb allocation") by making sure to require both bulk-in and out
endpoints during port probe.
The original option driver (which usb_wwan is based on) was written
under the assumption that either endpoint could be missing, but
evidently this cannot have been tested properly. Specifically, it would
handle opening a device without bulk-in (but would blow up during resume
which was implemented later), but not a missing bulk-out in write()
(although it is handled in some places such as write_room()).
Fortunately (?), the driver also got the test for missing endpoints
wrong so the urbs were in fact always allocated, although they would be
initialised using the wrong endpoint address (0) and any submission of
such an urb would fail.
The commit mentioned above fixed the test for missing endpoints but
thereby exposed the other bugs which would now generate null-pointer
exceptions rather than failed urb submissions.
The regression was introduced in v3.7, but the offending commit was also
marked for stable.
Reported-by: Rafał Miłecki <zajec5@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Tested-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add device ids to pl2303 for the Hewlett-Packard HP POS pole displays:
LD960: 03f0:0B39
LCM220: 03f0:3139
LCM960: 03f0:3239
[ Johan: fix indentation and sort PIDs numerically ]
Signed-off-by: Aaron Sanders <aaron.sanders@hp.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Tristan Bruns <tristan@tristanbruns.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
option driver, added VID/PID for Telit UE910v2 modem
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 1ebca9dad5abe8b2ed4dbd186cd657fb47c1f321.
This device was erroneously added to the sierra driver even though it's
not a Sierra device and was already handled by the option driver.
Cc: Richard Farina <sidhayn@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Custom VID/PIDs for Brainboxes cards as reported in
https://bugzilla.redhat.com/show_bug.cgi?id=1071914
Signed-off-by: Michele Baldessari <michele@acksyn.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
Pull SCSI target updates from Nicholas Bellinger:
"Here are the target pending updates for v3.15-rc1. Apologies in
advance for waiting until the second to last day of the merge window
to send these out.
The highlights this round include:
- iser-target support for T10 PI (DIF) offloads (Sagi + Or)
- Fix Task Aborted Status (TAS) handling in target-core (Alex Leung)
- Pass in transport supported PI at session initialization (Sagi + MKP + nab)
- Add WRITE_INSERT + READ_STRIP T10 PI support in target-core (nab + Sagi)
- Fix iscsi-target ERL=2 ASYNC_EVENT connection pointer bug (nab)
- Fix tcm_fc use-after-free of ft_tpg (Andy Grover)
- Use correct ib_sg_dma primitives in ib_isert (Mike Marciniszyn)
Also, note the virtio-scsi + vhost-scsi changes to expose T10 PI
metadata into KVM guest have been left-out for now, as there where a
few comments from MST + Paolo that where not able to be addressed in
time for v3.15. Please expect this feature for v3.16-rc1"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (43 commits)
ib_srpt: Use correct ib_sg_dma primitives
target/tcm_fc: Rename ft_tport_create to ft_tport_get
target/tcm_fc: Rename ft_{add,del}_lport to {add,del}_wwn
target/tcm_fc: Rename structs and list members for clarity
target/tcm_fc: Limit to 1 TPG per wwn
target/tcm_fc: Don't export ft_lport_list
target/tcm_fc: Fix use-after-free of ft_tpg
target: Add check to prevent Abort Task from aborting itself
target: Enable READ_STRIP emulation in target_complete_ok_work
target/sbc: Add sbc_dif_read_strip software emulation
target: Enable WRITE_INSERT emulation in target_execute_cmd
target/sbc: Add sbc_dif_generate software emulation
target/sbc: Only expose PI read_cap16 bits when supported by fabric
target/spc: Only expose PI mode page bits when supported by fabric
target/spc: Only expose PI inquiry bits when supported by fabric
target: Pass in transport supported PI at session initialization
target/iblock: Fix double bioset_integrity_free bug
Target/sbc: Initialize COMPARE_AND_WRITE write_sg scatterlist
target/rd: T10-Dif: RAM disk is allocating more space than required.
iscsi-target: Fix ERL=2 ASYNC_EVENT connection pointer bug
...
|
|
In order to support local WRITE_INSERT + READ_STRIP operations for
non PI enabled fabrics, the fabric driver needs to be able signal
what protection offload operations are supported.
This is done at session initialization time so the modes can be
signaled by individual se_wwn + se_portal_group endpoints, as well
as optionally across different transports on the same endpoint.
For iser-target, set TARGET_PROT_ALL if the underlying ib_device
has already signaled PI offload support, and allow this to be
exposed via a new iscsit_transport->iscsit_get_sup_prot_ops()
callback.
For loopback, set TARGET_PROT_ALL to signal SCSI initiator mode
operation.
For all other drivers, set TARGET_PROT_NORMAL to disable fabric
level PI.
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Now that TASK_ABORTED status is not generated for all cases by
TMR ABORT_TASK + LUN_RESET, a new TFO->abort_task() caller is
necessary in order to give fabric drivers a chance to unmap
hardware / software resources before the se_cmd descriptor is
released via the normal TFO->release_cmd() codepath.
This patch adds TFO->aborted_task() in core_tmr_abort_task()
in place of the original transport_send_task_abort(), and
also updates all fabric drivers to implement this caller.
The fabric drivers that include changes to perform cleanup
via ->aborted_task() are:
- iscsi-target
- iser-target
- srpt
- tcm_qla2xxx
The fabric drivers that currently set ->aborted_task() to
NOPs are:
- loopback
- tcm_fc
- usb-gadget
- sbp-target
- vhost-scsi
For the latter five, there appears to be no additional cleanup
required before invoking TFO->release_cmd() to release the
se_cmd descriptor.
v2 changes:
- Move ->aborted_task() call into transport_cmd_finish_abort (Alex)
Cc: Alex Leung <amleung21@yahoo.com>
Cc: Mark Rustad <mark.d.rustad@intel.com>
Cc: Roland Dreier <roland@kernel.org>
Cc: Vu Pham <vu@mellanox.com>
Cc: Chris Boot <bootc@bootc.net>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Cc: Saurav Kashyap <saurav.kashyap@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Pull ARM changes from Russell King:
- Perf updates from Will Deacon:
- Support for Qualcomm Krait processors (run perf on your phone!)
- Support for Cortex-A12 (run perf stat on your FPGA!)
- Support for perf_sample_event_took, allowing us to automatically decrease
the sample rate if we can't handle the PMU interrupts quickly enough
(run perf record on your FPGA!).
- Basic uprobes support from David Long:
This patch series adds basic uprobes support to ARM. It is based on
patches developed earlier by Rabin Vincent. That approach of adding
hooks into the kprobes instruction parsing code was not well received.
This approach separates the ARM instruction parsing code in kprobes out
into a separate set of functions which can be used by both kprobes and
uprobes. Both kprobes and uprobes then provide their own semantic action
tables to process the results of the parsing.
- ARMv7M (microcontroller) updates from Uwe Kleine-König
- OMAP DMA updates (recently added Vinod's Ack even though they've been
sitting in linux-next for a few months) to reduce the reliance of
omap-dma on the code in arch/arm.
- SA11x0 changes from Dmitry Eremin-Solenikov and Alexander Shiyan
- Support for Cortex-A12 CPU
- Align support for ARMv6 with ARMv7 so they can cooperate better in a
single zImage.
- Addition of first AT_HWCAP2 feature bits for ARMv8 crypto support.
- Removal of IRQ_DISABLED from various ARM files
- Improved efficiency of virt_to_page() for single zImage
- Patch from Ulf Hansson to permit runtime PM callbacks to be available for
AMBA devices for suspend/resume as well.
- Finally kill asm/system.h on ARM.
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (89 commits)
dmaengine: omap-dma: more consolidation of CCR register setup
dmaengine: omap-dma: move IRQ handling to omap-dma
dmaengine: omap-dma: move register read/writes into omap-dma.c
ARM: omap: dma: get rid of 'p' allocation and clean up
ARM: omap: move dma channel allocation into plat-omap code
ARM: omap: dma: get rid of errata global
ARM: omap: clean up DMA register accesses
ARM: omap: remove almost-const variables
ARM: omap: remove references to disable_irq_lch
dmaengine: omap-dma: cleanup errata 3.3 handling
dmaengine: omap-dma: provide register read/write functions
dmaengine: omap-dma: use cached CCR value when enabling DMA
dmaengine: omap-dma: move barrier to omap_dma_start_desc()
dmaengine: omap-dma: move clnk_ctrl setting to preparation functions
dmaengine: omap-dma: improve efficiency loading C.SA/C.EI/C.FI registers
dmaengine: omap-dma: consolidate clearing channel status register
dmaengine: omap-dma: move CCR buffering disable errata out of the fast path
dmaengine: omap-dma: provide register definitions
dmaengine: omap-dma: consolidate setup of CCR
dmaengine: omap-dma: consolidate setup of CSDP
...
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree updates from Jiri Kosina:
"Usual rocket science -- mostly documentation and comment updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
sparse: fix comment
doc: fix double words
isdn: capi: fix "CAPI_VERSION" comment
doc: DocBook: Fix typos in xml and template file
Bluetooth: add module name for btwilink
driver core: unexport static function create_syslog_header
mmc: core: typo fix in printk specifier
ARM: spear: clean up editing mistake
net-sysfs: fix comment typo 'CONFIG_SYFS'
doc: Insert MODULE_ in module-signing macros
Documentation: update URL to hfsplus Technote 1150
gpio: update path to documentation
ixgbe: Fix format string in ixgbe_fcoe.
Kconfig: Remove useless "default N" lines
user_namespace.c: Remove duplicated word in comment
CREDITS: fix formatting
treewide: Fix typo in Documentation/DocBook
mm: Fix warning on make htmldocs caused by slab.c
ata: ata-samsung_cf: cleanup in header file
idr: remove unused prototype of idr_free()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg KH:
"Here's the big USB pull request for 3.15-rc1.
The normal set of patches, lots of controller driver updates, and a
smattering of individual USB driver updates as well.
All have been in linux-next for a while"
* tag 'usb-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (249 commits)
xhci: Transition maintainership to Mathias Nyman.
USB: disable reset-resume when USB_QUIRK_RESET is set
USB: unbind all interfaces before rebinding any
usb: phy: Add ulpi IDs for SMSC USB3320 and TI TUSB1210
usb: gadget: tcm_usb_gadget: stop format strings
usb: gadget: f_fs: add missing spinlock and mutex unlock
usb: gadget: composite: switch over to ERR_CAST()
usb: gadget: inode: switch over to memdup_user()
usb: gadget: f_subset: switch over to PTR_RET
usb: gadget: lpc32xx_udc: fix wrong clk_put() sequence
USB: keyspan: remove dead debugging code
USB: serial: add missing newlines to dev_<level> messages.
USB: serial: add missing braces
USB: serial: continue to write on errors
USB: serial: continue to read on errors
USB: serial: make bulk_out_size a lower limit
USB: cypress_m8: fix potential scheduling while atomic
devicetree: bindings: document lsi,zevio-usb
usb: chipidea: add support for USB OTG controller on LSI Zevio SoCs
usb: chipidea: imx: Use dev_name() for ci_hdrc name to distinguish USBs
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver update from Greg KH:
"Here's the big tty/serial driver update for 3.15-rc1.
Nothing major, a number of serial driver updates and a few tty core
fixes as well.
All have been in linux-next for a while"
* tag 'tty-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (71 commits)
tty/serial: omap: empty the RX FIFO at the end of half-duplex TX
tty/serial: omap: fix RX interrupt enable/disable in half-duplex TX
serial: sh-sci: Neaten dev_<level> uses
serial: sh-sci: Replace hardcoded 3 by UART_PM_STATE_OFF
serial: sh-sci: Add more register documentation
serial: sh-sci: Remove useless casts
serial: sh-sci: Replace printk() by pr_*()
serial_core: Avoid NULL pointer dereference in uart_close()
serial_core: Get a reference for port->tty in uart_remove_one_port()
serial: clps711x: Give a chance to perform useful tasks during wait loop
serial_core: Grammar s/ports/port's/
serial_core: Spelling s/contro/control/
serial: efm32: properly namespace location property
serial: max310x: Add missing #include <linux/uaccess.h>
synclink: fix info leak in ioctl
serial: 8250: Clean up the locking for -rt
serial: 8250_pci: change BayTrail default uartclk
serial: 8250_pci: more BayTrail error-free bauds
serial: sh-sci: Add missing call to uart_remove_one_port() in failure path
serial_core: Unregister console in uart_remove_one_port()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here's the huge drivers/staging/ update for 3.15-rc1.
Loads of cleanup fixes, a few drivers removed, and some new ones
added.
All have been in linux-next for a while"
* tag 'staging-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1375 commits)
staging: xillybus: XILLYBUS_PCIE depends on PCI_MSI
staging: xillybus: Added "select CRC32" for XILLYBUS in Kconfig
staging: comedi: poc: remove obsolete driver
staging: unisys: replace kzalloc/kfree with UISMALLOC/UISFREE
staging: octeon-usb: prevent memory corruption
staging: usbip: fix line over 80 characters
staging: usbip: fix quoted string split across lines
Staging: unisys: Remove RETINT macro
Staging: unisys: Remove FAIL macro
Staging: unisys: Remove RETVOID macro
Staging: unisys: Remove RETPTR macro
Staging: unisys: Remove RETBOOL macro
Staging: unisys: Remove FAIL_WPOSTCODE_1 macro
Staging: unisys: Cleanup macros to get rid of goto statements
Staging: unisys: include: Remove unused macros from timskmod.h
staging: dgap: fix the rest of the checkpatch warnings in dgap.c
Staging: bcm: Remove unnecessary parentheses
staging: wlags49_h2: Delete unnecessary braces
staging: wlags49_h2: Do not use assignment in if condition
staging: wlags49_h2: Enclose macro in a do-while loop
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver patches from Greg KH:
"Here's the big char/misc driver updates for 3.15-rc1.
Lots of various things here, including the new mcb driver subsystem.
All of these have been in linux-next for a while"
* tag 'char-misc-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (118 commits)
extcon: Move OF helper function to extcon core and change function name
extcon: of: Remove unnecessary function call by using the name of device_node
extcon: gpio: Use SIMPLE_DEV_PM_OPS macro
extcon: palmas: Use SIMPLE_DEV_PM_OPS macro
mei: don't use deprecated DEFINE_PCI_DEVICE_TABLE macro
mei: amthif: fix checkpatch error
mei: client.h fix checkpatch errors
mei: use cl_dbg where appropriate
mei: fix Unnecessary space after function pointer name
mei: report consistently copy_from/to_user failures
mei: drop pr_fmt macros
mei: make me hw headers private to me hw.
mei: fix memory leak of pending write cb objects
mei: me: do not reset when less than expected data is received
drivers: mcb: Fix build error discovered by 0-day bot
cs5535-mfgpt: Simplify dependencies
spmi: pm: drop bus-level PM suspend/resume routines
spmi: pmic_arb: make selectable on ARCH_QCOM
Drivers: hv: vmbus: Increase the limit on the number of pfns we can handle
pch_phub: Report error writing MAC back to user
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"There have been lots of changes in ALSA core, HD-audio and ASoC, also
most of PCI drivers touched by conversions of printks. All these
resulted in a high volume and wide ranged patch sets in this release.
Many changes are fairly trivial, but also lots of nice cleanups and
refactors. There are a few new drivers, most notably, the Intel
Haswell and Baytrail ASoC driver.
Core changes:
- A bit modernization; embed the device struct into snd_card struct,
so that it may be referred from the beginning. A new
snd_card_new() function is introduced for that, and all drivers
have been converted.
- Simplification in the device management code in ALSA core; now
managed by a simple priority list instead
- Converted many kernel messages to use the standard dev_err() & co;
this would be the pretty visible difference, especially for
HD-audio.
HD-audio:
- Conexant codecs use the auto-parser as default now; the old static
code still remains in case of regressions. Some old quirks have
been rewritten with the fixups for auto-parser.
- C-Media codecs also use the auto-parser as default now, too.
- A device struct is assigned to each HD-audio codec, and the
formerly hwdep attributes are accessible over the codec sysfs, too.
hwdep attributes still remain for compatibility.
- Split the PCI-specific stuff for HD-audio controller into a
separate module, ane make a helper module for the generic
controller driver. This is a preliminary change for supporting
Tegra HDMI controller in near future, which slipped from 3.15
merge.
- Device-specific fixes: mute LED support for Lenovo Ideapad, mic LED
fix for HP laptops, more ASUS subwoofer quirks, yet more Dell
laptop headset quirks
- Make the HD-audio codec response a bit more robust
- A few improvements on Realtek ALC282 / 283 about the pop noises
- A couple of Intel HDMI fixes
ASoC:
- Lots of cleanups for enumerations; refactored lots of error prone
original codes to use more modern APIs
- Elimination of the ASoC level wrappers for I2C and SPI moving us
closer to converting to regmap completely and avoiding some
randconfig hassle
- Provide both manually and transparently locked DAPM APIs rather
than a mix of the two fixing some concurrency issues
- Start converting CODEC drivers to use separate bus interface
drivers rather than having them all in one file helping avoid
dependency issues
- DPCM support for Intel Haswell and Bay Trail platforms, lots of
fixes
- Lots of work on improvements for simple-card, DaVinci and the
Renesas rcar drivers.
- New drivers for Analog Devices ADAU1977, TI PCM512x and parts of
the CSR SiRF SoC, TLV320AIC31XXX, Armada 370 DB, Cirrus cs42xx8
- Fixes for the simple-card DAI format DT mess
- DT support for a couple more devices.
- Use of the tdm_slot mapping in a few drivers
Others:
- Support of reset_resume callback for improved S4 in USB-audio
driver; the device with boot quirks have been little tested, which
we need to watch out in this development cycle
- Add PM support for ICE1712 driver (finally!); it's still pretty
partial support, only for M-Audio devices"
* tag 'sound-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (610 commits)
ALSA: ice1712: Add suspend support for M-Audio ICE1712-based cards
ALSA: ice1712: add suspend support for ICE1712 chip
ALSA: hda - Enable beep for ASUS 1015E
ALSA: asihpi: fix some indenting in snd_card_asihpi_pcm_new()
ALSA: hda - add headset mic detect quirks for three Dell laptops
ASoC: tegra: move AC97 clock handling to the machine driver
ASoC: simple-card: Handle many DAI links
ASoC: simple-card: Add DT documentation for multi-DAI links
ASoC: simple-card: dynamically allocate the DAI link and properties
ASoC: imx-ssi: Add .xlate_tdm_slot_mask() support.
ASoC: fsl-esai: Add .xlate_tdm_slot_mask() support.
ASoC: fsl-utils: Add fsl_asoc_xlate_tdm_slot_mask() support.
ASoC: core: remove the 'of_' prefix of of_xlate_tdm_slot_mask.
ASoC: rcar: subnode tidyup for renesas,rsnd.txt
ASoC: Remove name_prefix unset during DAI link init hack
ALSA: hda - Inform the unexpectedly ignored pins by auto-parser
ASoC: rcar: bugfix: it cares about the non-src case
ARM: bockw: fixup SND_SOC_DAIFMT_CBx_CFx flags
ASoC: pcm: Drop incorrect double/extra frees
ASoC: mfld_machine: Fix compile error
...
|
|
Pull workqueue changes from Tejun Heo:
"PREPARE_[DELAYED_]WORK() were used to change the work function of work
items without fully reinitializing it; however, this makes workqueue
consider the work item as a different one from before and allows the
work item to start executing before the previous instance is finished
which can lead to extremely subtle issues which are painful to debug.
The interface has never been popular. This pull request contains
patches to remove existing usages and kill the interface. As one of
the changes was routed during the last devel cycle and another
depended on a pending change in nvme, for-3.15 contains a couple merge
commits.
In addition, interfaces which were deprecated quite a while ago -
__cancel_delayed_work() and WQ_NON_REENTRANT - are removed too"
* 'for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: remove deprecated WQ_NON_REENTRANT
workqueue: Spelling s/instensive/intensive/
workqueue: remove PREPARE_[DELAYED_]WORK()
staging/fwserial: don't use PREPARE_WORK
afs: don't use PREPARE_WORK
nvme: don't use PREPARE_WORK
usb: don't use PREPARE_DELAYED_WORK
floppy: don't use PREPARE_[DELAYED_]WORK
ps3-vuart: don't use PREPARE_WORK
wireless/rt2x00: don't use PREPARE_WORK in rt2800usb.c
workqueue: Remove deprecated __cancel_delayed_work()
|
|
The USB_QUIRK_RESET flag indicates that a USB device changes its
identity in some way when it is reset. It may lose its firmware, its
descriptors may change, or it may switch back to a default mode of
operation.
If a device does this, the kernel needs to avoid resetting it. Resets
are likely to fail, or worse, succeed while changing the device's
state in a way the system can't detect.
This means we should disable the reset-resume mechanism whenever this
quirk flag is present. An attempted reset-resume will fail, the
device will be logically disconnected, and later on the hub driver
will rediscover and re-enumerate the device. This will cause the
appropriate udev events to be generated, so that userspace will have a
chance to switch the device into its normal operating mode, if
necessary.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Oliver Neukum <oliver@neukum.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch move simply OF helper function to extcon core and change function
name as following:
- of_extcon_get_extcon_dev() -> extcon_get_edev_by_phandle()
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
|
|
When a driver doesn't have pre_reset, post_reset, or reset_resume
methods, the USB core unbinds that driver when its device undergoes a
reset or a reset-resume, and then rebinds it afterward.
The existing straightforward implementation can lead to problems,
because each interface gets unbound and rebound before the next
interface is handled. If a driver claims additional interfaces, the
claim may fail because the old binding instance may still own the
additional interface when the new instance tries to claim it.
This patch fixes the problem by first unbinding all the interfaces
that are marked (i.e., their needs_binding flag is set) and then
rebinding all of them.
The patch also makes the helper functions in driver.c a little more
uniform and adjusts some out-of-date comments.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: "Poulain, Loic" <loic.poulain@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add new ulpi IDs which are available on Xilinx Zynq boards.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This makes sure that the name coming out of configfs cannot be used
accidentally as a format string.
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds missing spin_unlock and mutex_unlock calls in
error handling code.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch fixes the following Coccinelle warning:
drivers/usb/gadget/composite.c:1142:9-16: WARNING: \
ERR_CAST can be used with uc
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch fixes the following Coccinelle warning:
drivers/usb/gadget/inode.c:442:8-15: WARNING \
opportunity for memdup_user
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
this patch fixes the following Coccinelle warning:
drivers/usb/gadget/f_subset.c:279:8-14: WARNING: \
PTR_RET can be used
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch fixes the following Coccinelle error:
drivers/usb/gadget/lpc32xx_udc.c:3313:1-7: ERROR: \
missing clk_put; clk_get on line 3139 and \
execution via conditional on line 3146
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This resolves a merge issue with drivers/staging/cxt1e1/linux.c that was
fixed in a report from Stephen Rothwell
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v3.15
Quite a busy release for ASoC this time, more on janitorial work than
exciting new features but welcome nontheless:
- Lots of cleanups from Takashi for enumerations; the original API for
these was error prone so he's refactored lots of code to use more
modern APIs which avoid issues.
- Elimination of the ASoC level wrappers for I2C and SPI moving us
closer to converting to regmap completely and avoiding some
randconfig hassle.
- Provide both manually and transparently locked DAPM APIs rather than
a mix of the two fixing some concurrency issues.
- Start converting CODEC drivers to use separate bus interface drivers
rather than having them all in one file helping avoid dependency
issues.
- DPCM support for Intel Haswell and Bay Trail platforms.
- Lots of work on improvements for simple-card, DaVinci and the Renesas
rcar drivers.
- New drivers for Analog Devices ADAU1977, TI PCM512x and parts of the
CSR SiRF SoC.
|
|
Remove out-commented and ifdeffed debugging code.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
|
|
Add missing newlines to dev_<level> messages.
Also make some messages less verbose where appropriate.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
|
|
Add missing braces to conditional branches and one loop in usb-serial
core and generic implementation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
|
|
Do not discard buffered data and make sure to try to resubmit the write
urbs on errors.
Currently a recoverable error would lead to more data than necessary
being dropped.
Also upgrade error messages from debug to error log level.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
|
|
Make sure to try to resubmit the read urb on errors.
Currently a recoverable error would lead to reduced throughput as only
one urb will be used until the port is closed and reopened (or
resumed or unthrottled).
Also upgrade error messages from debug to error log level.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
|
|
Drivers are allowed to override the default bulk-out buffer size
(endpoint maximum packet size) in order to increase throughput, but it
does not make much sense to allow buffers smaller than the default.
Note that this is already how bulk_in_size is defined.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
|
|
Remove erroneous call to usb_clear_halt which is blocking and cannot be
used in interrupt context.
This code has possibly never been executed as it would cause an oops if
it was. Simply treat a stalled-endpoint error as any other error
condition.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
|
|
The USB controller in TI-NSPIRE calculators (LSI Zevio SoC) are based off either
Freescale's USB OTG controller or the USB controller found in the IMX233, both
of which are Chipidea compatible.
This patch adds a device tree binding for the controller.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Daniel Tang <dt.tangr@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
