Age | Commit message (Collapse) | Author |
|
The users have been converted to use the ehci platform driver instead, thus
making the ehci-cns3xxx driver obsolete, so remove it.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The platform code has been converted to use the ehci-platform driver instead
thus obsoleting the ehci-au1xxx driver, which can be removed.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Enhance the ehci-platform driver to also accept no_io_watchdog as a platform
data parameter. When no_io_watchdog is set to 1, the ehci controller will set
ehci->need_io_watchdog to 0. Since most EHCI controllers do need the I/O
watchdog to be on, only let those which need it to turn the watchdog off.
Make sure that we change need_io_watchdog after the call to ehci_setup()
because ehci_setup() will unconditionnaly set need_io_watchdog to 1.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The platform code has been migrated to register the ehci-platform driver, thus
obsoleting the ehci-xls driver, which can be removed.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The platform code registering the Loongson 1B EHCI driver has now been
converted to register the ehci-platform driver instead, thus obsoleting the
ehci-ls1x driver, which can be removed.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This driver is not registered by any in-tree users, and if really needed by
some out of tree user, the same functionnality can be restored using the
ohci-platform driver using the following platform_data parameters:
big_endian_desc = 1
big_endian_mmio = 1
no_big_frame_no = 1
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This driver is not registered by any in-tree user. If needed it the EHCI
driver can be reinstatied using the ehci-platform driver with caps_offset to
0x100.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch (as1614) updates the isochronous scheduling in ohci-hcd to
match the new semantics for URB_ISO_ASAP. Testing revealed a hardware
bug in the way my OHCI controller handles expired isochronous TDs;
consequently the patch tries hard to avoid creating them (unlike the
ehci-hcd and uhci-hcd drivers).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch (as1613) updates the isochronous scheduling in uhci-hcd to
match the new semantics for URB_ISO_ASAP. The amount of code
alteration is smaller than it looks because of a change in the
indentation level.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch (as1612) updates the isochronous scheduling and processing
in ehci-hcd to match the new semantics for URB_ISO_ASAP. It also adds
a missing "unlikely" in sitd_complete() to match the corresponding
statement in itd_complete(), and it increments urb->error_count in a
couple of places that had been overlooked.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch (as1611) updates the USB documentation and kerneldoc to
give a more precise meaning for the URB_ISO_ASAP flag and to explain
more of the details of scheduling for isochronous URBs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch (as1610) replaces multiplication and divison operations in
ehci-hcd's isochronous scheduling code with a bit-mask operation,
taking advantage of the fact that isochronous periods are always
powers of 2.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch (as1609) changes the way ehci-hcd uses the "Isochronous
Scheduling Threshold" in its calculations. Until now the code has
ignored the threshold except for certain Intel PCI-based controllers.
This violates the EHCI spec.
The new code takes the threshold into account always, removing the
need for the fs_i_thresh quirk flag. In addition it implements the
"full frame cache" setting more efficiently, moving forward only as
far as the next frame boundary instead of always moving forward 8
microframes.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch (as1608) reworks the logic used by ehci-hcd for scheduling
isochronous transfers. Now the modular calculations are all based on
a window that starts at the last frame scanned for isochronous
completions. No transfer descriptors for any earlier frames can
possibly remain on the schedule, so there can be no confusion from
schedule wrap-around. This removes the need for a "slop" region of
arbitrary size.
There's no need to check for URBs that are longer than the schedule
length. With the old code they could throw things off by wrapping
around and appearing to end in the near future rather than the distant
future. Now such confusion isn't possible, and the existing test for
submissions that extend too far into the future will also catch those
that exceed the schedule length. (But there still has to be an
initial test to handle the case where the schedule already extends as
far into the future as possible.)
Delays caused by IRQ latency won't confuse the algorithm unless they
are ridiculously long (over 250 ms); they will merely reduce how far
into the future new transfers can be scheduled. A few people have
reported problems caused by delays of 50 ms or so. Now instead of
failing completely, isochronous transfers will experience a brief
glitch and then continue normally.
(Whether this is truly a good thing is debatable. A latency as large
as 50 ms generally indicates a bug is present, and complete failure of
audio or video transfers draws people's attention pretty vividly.
Making the transfers more robust also makes it easier for such bugs to
remain undetected.)
Finally, ehci->next_frame is renamed to ehci->last_iso_frame, because
that better describes what it is: the last frame to have been scanned
for isochronous completions.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc fixes from Olof Johansson:
"A set of fixes and some minor cleanups for -rc2:
- A series from Arnd that fixes warnings in drivers and other code
included by ARM defconfigs. Most have been acked by corresponding
maintainers (and seem quite hard to argue not picking up anyway in
the few exception cases).
- A few misc patches from the list for integrator/vt8500/i.MX
- A batch of fixes to OMAP platforms, fixing:
- boot problems on beaglebone,
- regression fixes for local timers
- clockdomain locking fixes
- a few boot/sparse warnings
- For Tegra:
- Clock rate calculation overflow fix
- Revert a change that removed timer clocks and a fix for symbol
name clashes
- For Renesas:
- IO accessor / annotation cleanups to remove warnings
- For Kirkwood/Dove/mvebu:
- Fixes for device trees for Dove (some minor cleanups, some fixes)
- Fixes for the mvebu gpio driver
- Fix build problem for Feroceon due to missing ifdefs
- Fix lsxl DTS files"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits)
ARM: kirkwood: fix buttons on lsxl boards
ARM: kirkwood: fix LEDs names for lsxl boards
ARM: Kirkwood: fix disabling CACHE_FEROCEON_L2
gpio: mvebu: Add missing breaks in mvebu_gpio_irq_set_type
ARM: dove: Add crypto engine to DT
ARM: dove: Remove watchdog from DT
ARM: dove: Restructure SoC device tree descriptor
ARM: dove: Fix clock names of sata and gbe
ARM: dove: Fix tauros2 device tree init
ARM: dove: Add pcie clock support
ARM: OMAP2+: Allow kernel to boot even if GPMC fails to reserve memory
ARM: OMAP: clockdomain: Fix locking on _clkdm_clk_hwmod_enable / disable
ARM: s3c: mark s3c2440_clk_add as __init_refok
spi/s3c64xx: use correct dma_transfer_direction type
ARM: OMAP4: devices: fixup OMAP4 DMIC platform device error message
ARM: OMAP2+: clock data: Add dev-id for the omap-gpmc dummy fck
ARM: OMAP: resolve sparse warning concerning debug_card_init()
ARM: OMAP4: Fix twd_local_timer_register regression
ARM: tegra: add tegra_timer clock
ARM: tegra: rename tegra system timer
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into fixes
A collection of warning fixes on non-ARM code from Arnd Bergmann:
* 'testing/driver-warnings' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: s3c: mark s3c2440_clk_add as __init_refok
spi/s3c64xx: use correct dma_transfer_direction type
pcmcia: sharpsl: don't discard sharpsl_pcmcia_ops
USB: EHCI: mark ehci_orion_conf_mbus_windows __devinit
mm/slob: use min_t() to compare ARCH_SLAB_MINALIGN
SCSI: ARM: make fas216_dumpinfo function conditional
SCSI: ARM: ncr5380/oak uses no interrupts
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are the USB patches against your 3.7-rc1 tree.
There are the usual UABI header file movements, and we finally are now
able to remove the dbg() macro that is over 15 years old (that had to
wait for after some other trees got merged into yours during the big
3.7-rc1 merge window.)
Other than that, nothing major, just a number of bugfixes and new
device ids. It turns out that almost all of the usb-serial drivers
had bugs in how they were handling their internal data, leaking
memory, hence all of those fixups.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (42 commits)
USB: option: add more ZTE devices
USB: option: blacklist net interface on ZTE devices
usb: host: xhci: New system added for Compliance Mode Patch on SN65LVPE502CP
USB: io_ti: fix sysfs-attribute creation
USB: iuu_phoenix: fix sysfs-attribute creation
USB: spcp8x5: fix port-data memory leak
USB: ssu100: fix port-data memory leak
USB: ti_usb_3410_5052: fix port-data memory leak
USB: oti6858: fix port-data memory leak
USB: iuu_phoenix: fix port-data memory leak
USB: kl5kusb105: fix port-data memory leak
USB: io_ti: fix port-data memory leak
USB: keyspan_pda: fix port-data memory leak
USB: f81232: fix port-data memory leak
USB: io_edgeport: fix port-data memory leak
USB: kobil_sct: fix port-data memory leak
USB: cypress_m8: fix port-data memory leak
usb: acm: fix the computation of the number of data bits
usb: Missing dma_mask in ehci-vt8500.c when probed from device-tree
usb: Missing dma_mask in uhci-platform.c when probed from device-tree
...
|
|
ehci_fsl_setup_phy is supposed to return an int, but had a void return
value in the case of controller_ver being invalid.
Introduced by commit 3735ba8db8e6 ("powerpc/usb: fix bug of CPU hang
when missing USB PHY clock"), which missed one return.
Signed-off-by: Ben Collins <ben.c@servergy.com>
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
commit 93abe8e (clk: add non CONFIG_HAVE_CLK routines)
added clk API stubs when !defined(CONFIG_HAVE_CLK).
This allows us to remove the HAVE_CLK dependency from
Exynos' glue layer and let it compile always.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Based on information from the ZTE Windows drivers.
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
usb: fixes for v3.7-rc2
Here's the first set of fixes for v3.7-rc cycle.
DesignWare Core USB3 Driver (dwc3) got two fixes. The first one fixes a long
standing bug which would keep endpoint with BUSY flag set forever if we cancel
a transfer which has already been started by the controller. The second fix
will just switch PHYs back off when DWC3 driver is removed.
MUSB fixed a bug which would cause a Kernel Oops at least on AM3517 when
removing a device. For some reason that particular device can fall into a
situation where you have both Disconnect and Endpoint IRQs happen
simultaneously (have both bits set in IRQ_STATUS register) and, because
Disconnect Interrupt is handled before Endpoint Interrupts, we would try to
transfer data over a disconnected device, thus generating a kernel oops.
Renensas' USB DRD driver got two fixes which are a) fixing an off-by-one bug on
the pipe iterator implementation and b) fixing Interrupt Status Clear procedure
in order to properly clear a single Interrupt event without clearing (and
masking) other events we didn't handle yet.
|
|
This minor change adds a new system to which the "Fix Compliance Mode
on SN65LVPE502CP Hardware" patch has to be applied also.
System added:
Vendor: Hewlett-Packard. System Model: Z1
Signed-off-by: Alexis R. Cortes <alexis.cortes@ti.com>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure port data is initialised before creating sysfs attributes to
avoid a race.
A recent patch ("USB: io_ti: fix port-data memory leak") got the
sysfs-attribute creation and port-data initialisation ordering wrong.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure sysfs attributes are created at port probe.
A recent patch ("USB: iuu_phoenix: fix port-data memory leak") removed
the sysfs-attribute creation by mistake.
Reported-by: Yuanhan Liu <yuanhan.liu@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.
Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.
Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix port-data memory leak by moving port data allocation and
deallocation to port_probe and port_remove.
Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.
Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.
Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.
Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Note that the write waitqueue was initialised but never used.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix port-data memory leak by moving port data allocation and
deallocation to port_probe and port_remove.
Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.
Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Note that the write waitqueue was initialised but never used.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.
Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix port-data memory leak by moving port data allocation and
deallocation to port_probe and port_remove.
Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.
Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.
Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The current code assumes that CSIZE is 0000060, which appears to be
wrong on some arches (such as powerpc).
Signed-off-by: Nicolas Boullis <nboullis@debian.org>
Acked-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Device-tree probed devices don't get a dev.dma_mask set. This patch
sets a default 32bit mask on arch-vt8500 when using devicetree.
Without this patch, arch-vt8500 cannot detect ehci attached devices.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Device-tree probed devices don't get a dev.dma_mask set. This patch
sets a default 32bit mask on platforms using devicetree.
Without this patch, arch-vt8500 cannot detect uhci attached devices.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the write endpoint is interrupt type, usb_sndintpipe() should
be passed to usb_fill_int_urb() instead of usb_sndbulkpipe().
Cc: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The handling of large output bulk transfers is broken; the same user
page is read over and over again. Fixed with this patch.
Cc: stable <stable@vger.kernel.org>
Acked-by: Peter Stuge <peter@stuge.se>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There's no need to have this file in plat/fpga.h. We can
make it local to plat-omap replacing fpga_read/write
functions directly with readb/writeb as that's how
they are already defined in fpga.h.
Note that 2420 based H4 is also using the fpga, so let's
keep the led support around in plat-omap until we flip
over mach-omap2 to device tree.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: linux-fbdev@vger.kernel.org
Cc: Felipe Balbi <balbi@ti.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch (as1615) fixes a bug in the Garmin USB serial driver. It
uses attach, disconnect, and release routines to carry out actions
that should be handled by port_probe and port_remove routines, because
they access port-specific data.
The bug causes an oops when the device in unplugged, because the
private data for each port structure now gets erased when the port is
unbound from the driver, resulting in a null-pointer dereference.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported--by: Markus Schauler <mschauler@gmail.com>
Tested-by: Markus Schauler <mschauler@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix port-data memory leak by allocating and freeing port data in
port_probe/remove rather than in attach/release, and by introducing
serial private data to store the device type which is interface rather
than port specific.
Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix port data memory leak by replacing port private data with serial
private data.
Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at
release.
The private data is used to store the control interface number, but as
this is the same for all ports on an interface it should be stored as
usb-serial data anyway.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.
Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Note that the write waitqueue was initialised but never used.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.
Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Note that the write waitqueue was initialised but never used.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix NULL-pointer dereference at release by replacing attach and release
with port_probe and port_remove.
Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is NULL when release is called.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The STOTG04 is an replacement for ISP1301.
Most of the registers on STOTG04 are the same as on ISP1301, but the
register ISP1301_I2C_OTG_CONTROL_2 (address 0x10) doesn't exist on the
ST part.
This is a work around for this by using the interrupt source register that
should behave the same on both parts and has the needed information.
Tested-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|