| Age | Commit message (Collapse) | Author |
|---|
|
The xHCI host controller in the Panther Point chipset sometimes produces
spurious events on the event ring. If it receives a short packet, it
first puts a Transfer Event with a short transfer completion code on the
event ring. Then it puts a Transfer Event with a successful completion
code on the ring for the same TD. The xHCI driver correctly processes the
short transfer completion code, gives the URB back to the driver, and then
prints a warning in dmesg about the spurious event. These warning
messages really fill up dmesg when an HD webcam is plugged into xHCI.
This spurious successful event behavior isn't technically disallowed by
the xHCI specification, so make the xHCI driver just ignore the spurious
completion event.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
The Intel Panther Point chipsets contain an EHCI and xHCI host controller
that shares some number of skew-dependent ports. These ports can be
switched from the EHCI to the xHCI host (and vice versa) by a hardware MUX
that is controlled by registers in the xHCI PCI configuration space. The
USB 3.0 SuperSpeed terminations on the xHCI ports can be controlled
separately from the USB 2.0 data wires.
This switchover mechanism is there to support users who do a custom
install of certain non-Linux operating systems that don't have official
USB 3.0 support. By default, the ports are under EHCI, SuperSpeed
terminations are off, and USB 3.0 devices will show up under the EHCI
controller at reduced speeds. (This was more palatable for the marketing
folks than having completely dead USB 3.0 ports if no xHCI drivers are
available.) Users should be able to turn on xHCI by default through a
BIOS option, but users are happiest when they don't have to change random
BIOS settings.
This patch introduces a driver method to switchover the ports from EHCI to
xHCI before the EHCI driver finishes PCI enumeration. We want to switch
the ports over before the USB core has the chance to enumerate devices
under EHCI, or boot from USB mass storage will fail if the boot device
connects under EHCI first, and then gets disconnected when the port
switches over to xHCI.
Add code to the xHCI PCI quirk to switch the ports from EHCI to xHCI. The
PCI quirks code will run before any other PCI probe function is called, so
this avoids the issue with boot devices.
Another issue is with BIOS behavior during system resume from hibernate.
If the BIOS doesn't support xHCI, it may switch the devices under EHCI to
allow use of the USB keyboard, mice, and mass storage devices. It's
supposed to remember the value of the port routing registers and switch
them back when the OS attempts to take control of the xHCI host controller,
but we all know not to trust BIOS writers.
Make both the xHCI driver and the EHCI driver attempt to switchover the
ports in their PCI resume functions. We can't guarantee which PCI device
will be resumed first, so this avoids any race conditions. Writing a '1'
to an already set port switchover bit or a '0' to a cleared port switchover
bit should have no effect.
The xHCI PCI configuration registers will be documented in the EDS-level
chipset spec, which is not public yet. I have permission from legal and
the Intel chipset group to release this patch early to allow good Linux
support at product launch. I've tried to document the registers as much
as possible, so please let me know if anything is unclear.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
Unsurprisingly, URBs get submitted and completed a lot in the xHCI
driver. If we have to print 10 lines of debug for every URB submitted
or completed, then that can cause the whole system to stay in the
interrupt handler too long, and can cause Missed Service completion
codes for isochronous transfers.
Cut down the debugging in the URB submission and completion paths:
- Don't squawk about successful transfers, only unsuccessful ones.
- Only print the number of bytes transferred if this was a short
transfer.
- Don't print the endpoint index for successful transfers (will add
more debug to failed transfers to show endpoint index there later).
- Stop printing MMIO writes. This debugging shows up when the endpoint
doorbell is rung a to start a transfer (basically for every URB).
- Don't print out the ring enqueue and dequeue pointers
- Stop printing when we're pointing to a link TRB.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
Stop printing out the event ring dequeue pointer and status register in
the operational register set. The host will report an OK status 99% of
the time the interrupt handler is called, and usually when it's really
hosed, a host controller won't even call the interrupt handler. So the
line is really useless.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
Remove unnecessary debugging from the xHCI driver. We don't need to
know what function we're calling or returning from. Now I know how to
use markup-oops.pl to de-mystify stack dumps of crashes.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
When the xHCI host controller dies, the USB core may attempt to reset the
devices to their default configuration before disconnecting them. This
causes calls into the xHCI bandwidth allocation functions. Don't allow
those functions to submit commands or work on xHCI structures if the host
controller is marked as dying.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
When an URB is cancelled, the xHCI driver issues a Stop Endpoint command
so that it can manipulate the ring and remove the transfer. The xHC
hardware then places a transfer event with the completion code "Stopped"
or "Stopped Invalid" to let the driver know what TD it was in the middle
of processing. This TD and TRB is stored in ep->stopped_td and
ep->stopped_trb. These pointers are also used in handling stalled
endpoints.
By design, the Stop Endpoint command can race with URB completion. By
the time the Stop Endpoint command is handled, the URBs to be cancelled
may have been given back to the driver. Unfortunately, the stopped_td
and stopped_trb pointers were not getting cleared in this case.
The USB core unconditionally tries to reset the toggle bits on any
endpoints when a new alternate interface setting is installed. When the
xHCI driver saw that ep->stopped_td was still set from the Stop Endpoint
command, xhci_reset_endpoint assumed the endpoint was actually stalled,
and attempted to clean up the endpoint rings. This would manifest
itself in a failed Reset Endpoint command and failed Set TR dequeue
Pointer command after a successful Configure Endpoint command. It may
have also been causing driver oops when the stopped_td was accessed.
This patch should be backported to stable kernels since 2.6.31. Before
2.6.33, stopped_td was found in the xhci_endpoint_ring, not the
xhci_virt_ep.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (205 commits)
USB: EHCI: Remove SPARC_LEON {read,write}_be definitions from ehci.h
USB: UHCI: Support big endian GRUSBHC HC
sparc: add {read,write}*_be routines
USB: UHCI: Add support for big endian descriptors
USB: UHCI: Use ACCESS_ONCE rather than using a full compiler barrier
USB: UHCI: Add support for big endian mmio
usb-storage: Correct adjust_quirks to include latest flags
usb/isp1760: Fix possible unlink problems
usb/isp1760: Move function isp1760_endpoint_disable() within file.
USB: remove remaining usages of hcd->state from usbcore and fix regression
usb: musb: ux500: add configuration and build options for ux500 dma
usb: musb: ux500: add dma glue layer for ux500
usb: musb: ux500: add dma name for ux500
usb: musb: ux500: add ux500 specific code for gadget side
usb: musb: fix compile error
usb-storage: fix up the unusual_realtek device list
USB: gadget: f_audio: Fix invalid dereference of initdata
EHCI: don't rescan interrupt QHs needlessly
OHCI: fix regression caused by nVidia shutdown workaround
USB: OTG: msm: Free VCCCX regulator even if we can't set the voltage
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
b43: fix comment typo reqest -> request
Haavard Skinnemoen has left Atmel
cris: typo in mach-fs Makefile
Kconfig: fix copy/paste-ism for dell-wmi-aio driver
doc: timers-howto: fix a typo ("unsgined")
perf: Only include annotate.h once in tools/perf/util/ui/browsers/annotate.c
md, raid5: Fix spelling error in comment ('Ofcourse' --> 'Of course').
treewide: fix a few typos in comments
regulator: change debug statement be consistent with the style of the rest
Revert "arm: mach-u300/gpio: Fix mem_region resource size miscalculations"
audit: acquire creds selectively to reduce atomic op overhead
rtlwifi: don't touch with treewide double semicolon removal
treewide: cleanup continuations and remove logging message whitespace
ath9k_hw: don't touch with treewide double semicolon removal
include/linux/leds-regulator.h: fix syntax in example code
tty: fix typo in descripton of tty_termios_encode_baud_rate
xtensa: remove obsolete BKL kernel option from defconfig
m68k: fix comment typo 'occcured'
arch:Kconfig.locks Remove unused config option.
treewide: remove extra semicolons
...
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (110 commits)
[SCSI] qla2xxx: Refactor call to qla2xxx_read_sfp for thermal temperature.
[SCSI] qla2xxx: Unify the read/write sfp mailbox command routines.
[SCSI] qla2xxx: Clear complete initialization control block.
[SCSI] qla2xxx: Allow an override of the registered maximum LUN.
[SCSI] qla2xxx: Add host number in reset and quiescent message logs.
[SCSI] qla2xxx: Correctly read sfp single byte mailbox register.
[SCSI] qla2xxx: Add qla82xx_rom_unlock() function.
[SCSI] qla2xxx: Log if qla82xx firmware fails to load from flash.
[SCSI] qla2xxx: Use passed in host to initialize local scsi_qla_host in queuecommand function
[SCSI] qla2xxx: Correct buffer start in edc sysfs debug print.
[SCSI] qla2xxx: Update firmware version after flash update for ISP82xx.
[SCSI] qla2xxx: Fix hang during driver unload when vport is active.
[SCSI] qla2xxx: Properly set the dsd_list_len for dsd_chaining in cmd type 6.
[SCSI] qla2xxx: Fix virtual port failing to login after chip reset.
[SCSI] qla2xxx: Fix vport delete hang when logins are outstanding.
[SCSI] hpsa: Change memset using sizeof(ptr) to sizeof(*ptr)
[SCSI] ipr: Rate limit DMA mapping errors
[SCSI] hpsa: add P2000 to list of shared SAS devices
[SCSI] hpsa: do not attempt PCI power management reset method if we know it won't work.
[SCSI] hpsa: remove superfluous sleeps around reset code
...
|
|
Commit e66eed651fd1 ("list: remove prefetching from regular list
iterators") removed the include of prefetch.h from list.h, which
uncovered several cases that had apparently relied on that rather
obscure header file dependency.
So this fixes things up a bit, using
grep -L linux/prefetch.h $(git grep -l '[^a-z_]prefetchw*(' -- '*.[ch]')
grep -L 'prefetchw*(' $(git grep -l 'linux/prefetch.h' -- '*.[ch]')
to guide us in finding files that either need <linux/prefetch.h>
inclusion, or have it despite not needing it.
There are more of them around (mostly network drivers), but this gets
many core ones.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
{read,write}l_be are now defined for SPARC and do not need to be
defined for SPARC_LEON in ehci.h. This patch fixes the following
warnings:
CC drivers/usb/host/ehci-hcd.o
In file included from drivers/usb/host/ehci-hcd.c:119:
drivers/usb/host/ehci.h:631:1: warning: "readl_be" redefined
...
drivers/usb/host/ehci-hcd.c:119:
drivers/usb/host/ehci.h:632:1: warning: "writel_be" redefined
...
Signed-off-by: Jan Andersson <jan@gaisler.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch adds support for big endian GRUSBHC UHCI controllers.
The HCD bus glue will probe the register interface to determine
the endianness of the controller.
Tested on GR-LEON4-ITX board which has a controller with little endian
interface and on custom LEON3 board with a BE controller.
Signed-off-by: Jan Andersson <jan@gaisler.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch adds support for universal host controllers that use
big endian descriptors. Support for BE descriptors requires a non-PCI
host controller. For kernels with PCI-only UHCI there should be no
change in behaviour.
This patch tries to replicate the technique used to support BE descriptors
in the EHCI HCD. Parts added to uhci-hcd.h are basically copy'n'paste from
ehci.h.
Signed-off-by: Jan Andersson <jan@gaisler.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1462) updates the special accessor functions defined in
uhci-hcd.h. Rather than using a full compiler barrier, all we really
need is the ACCESS_ONCE() mechanism, because the idea is to force the
compiler to store a fixed copy of a possibly changing value.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch adds support for big endian mmio to the UHCI HCD. Big endian
mmio is supported by adding a flag bit to the UHCI HCD replicating the
solution used in the EHCI HCD.
When adding big endian support this patch also adds a check to see if we
need to support HCs with PCI I/O registers when we support HCs with MMIO.
This patch also adds 'const' to the register access functions' uhci_hcd
argument.
Signed-off-by: Jan Andersson <jan@gaisler.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Commits ae38c78a03e1b77ad45248fcf097e4568e740209
and 00914025cc4e783d4703b4db1d47b41f389e50c8 added quirk flags
US_FL_NO_READ_DISC_INFO and US_FL_NO_READ_CAPACITY_16 to
the usb-storage driver. However they did not add the corresponding flags
to adjust_quirks() in usb.c, so there was no facility for a user
to over-ride/add them via the quirks module parameter.
Signed-off-by: Karl Relton <karllinuxtest.relton@ntlworld.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Use skip map to avoid spurious interrupts from unlinked transfers.
Also changes to urb_dequeue() and endpoint_disable() to avoid
release of spinlock in uncertain state.
Signed-off-by: Arvid Brodin <arvid.brodin@enea.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Preparation for patch #2. The function isp1760_endpoint_disable() does almost
the same thing as urb_dequeue(). In patch #2 I change these to use a common
helper function instead of calling each other - for clarity but also to
avoid releasing the spinlock while in a "questionable" state. It seemed
proper to have these functions close to each other in the code.
Signed-off-by: Arvid Brodin <arvid.brodin@enea.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1467) removes the last usages of hcd->state from
usbcore. We no longer check to see if an interrupt handler finds that
a controller has died; instead we rely on host controller drivers to
make an explicit call to usb_hc_died().
This fixes a regression introduced by commit
9b37596a2e860404503a3f2a6513db60c296bfdc (USB: move usbcore away from
hcd->state). It used to be that when a controller shared an IRQ with
another device and an interrupt arrived while hcd->state was set to
HC_STATE_HALT, the interrupt handler would be skipped. The commit
removed that test; as a result the current code doesn't skip calling
the handler and ends up believing the controller has died, even though
it's only temporarily stopped. The solution is to ignore HC_STATE_HALT
following the handler's return.
As a consequence of this change, several of the host controller
drivers need to be modified. They can no longer implicitly rely on
usbcore realizing that a controller has died because of hcd->state.
The patch adds calls to usb_hc_died() in the appropriate places.
The patch also changes a few of the interrupt handlers. They don't
expect to be called when hcd->state is equal to HC_STATE_HALT, even if
the controller is still alive. Early returns were added to avoid any
confusion.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Manuel Lauss <manuel.lauss@googlemail.com>
CC: Rodolfo Giometti <giometti@linux.it>
CC: Olav Kongas <ok@artecdesign.ee>
CC: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Haavard's e-mail address at Atmel is no longer valid.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Havard Skinnemoen <hskinnemoen@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Commit b826291c, "drivercore/dt: add a match table pointer to struct
device" added an of_match pointer to struct device to cache the
of_match_table entry discovered at driver match time. This was unsafe
because matching is not an atomic operation with probing a driver. If
two or more drivers are attempted to be matched to a driver at the
same time, then the cached matching entry pointer could get
overwritten.
This patch reverts the of_match cache pointer and reworks all users to
call of_match_device() directly instead.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Unaligned sizes and buffers are not supported and they will be filtered
out by is_compatible().
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Although U8500 and U5500 platforms use paltform dma, Inventra dma specific code
can work for them for the most part. Only difference is for the Rx path where
this patch is making use of request->short_not_ok to select dma mode.
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
commit 35a83365da6aa10095c6138cc428c15853409c32
(usb: musb: drop unneeded musb_debug trickery)
introduced a compile error for blackfin and
tusb6010 glue layers. Fix it.
Reported-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch (as1461) fixes the unusual_devs entries for the Realtek USB
card reader. They should be ordered by PID, and they should not
override the Subclass and Protocol values provided by the device.
Otherwise a notification about unnecessary entries gets printed in the
kernel log during probing.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-By: Tony Vroon <tony@linx.net>
CC: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
as_out_ep_desc contines to be used during gadget enumeration and thus
should not be marked as __initdata
Signed-off-by: Martin Jackson <mjackson220.list@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1466) speeds up processing of ehci-hcd's periodic list.
The existing code will pointlessly rescan an interrupt endpoint queue
each time it encounters the queue's QH in the periodic list, which can
happen quite a few times if the endpoint's period is low. On some
embedded systems, this useless overhead can waste so much time that
the driver falls hopelessly behind and loses events.
The patch introduces a "periodic_stamp" variable, which gets
incremented each time scan_periodic() runs and each time the scan
advances to a new frame. If the corresponding stamp in an interrupt
QH is equal to the current periodic_stamp, we assume the QH has
already been scanned and skip over it. Otherwise we scan the QH as
usual, and if none of its URBs have completed then we store the
current periodic_stamp in the QH's stamp, preventing it from being
scanned again.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1463) fixes a regression caused by commit
3df7169e73fc1d71a39cffeacc969f6840cdf52b (OHCI: work around for nVidia
shutdown problem).
The original problem encountered by people using NVIDIA chipsets was
that USB devices were not turning off when the system shut down. For
example, the LED on an optical mouse would remain on, draining a
laptop's battery. The problem was caused by a bug in the chipset; an
OHCI controller in the Reset state would continue to drive a bus reset
signal even after system shutdown. The workaround was to put the
controllers into the Suspend state instead.
It turns out that later NVIDIA chipsets do not suffer from this bug.
Instead some have the opposite bug: If a system is shut down while an
OHCI controller is in the Suspend state, USB devices remain powered!
On other systems, shutting down with a Suspended controller causes the
system to reboot immediately. Thus, working around the original bug
on some machines exposes other bugs on other machines.
The best solution seems to be to limit the workaround to OHCI
controllers with a low-numbered PCI product ID. I don't know exactly
at what point NVIDIA changed their chipsets; the value used here is a
guess. So far it was worked out okay for all the people who have
tested it.
This fixes Bugzilla #35032.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Andre "Osku" Schmidt <andre.osku.schmidt@googlemail.com>
Tested-by: Yury Siamashka <yurand2@gmail.com>
CC: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
If for some reason we fail to set the voltage range for the VDDCX regulator
when removing it's better to still disable and free the regulator as that
avoids leaking a reference to it and is likely to ensure that it's turned
off completely.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
When not active the hardware should be able to tolerate voltages within
the normal operating range so when removing set the maximum voltage we
can use to the maximum rather than minimum of the operating range. This
will improve interoperability in case we end up sharing the supply in
some design.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
I am sharing patch to the devices/usb/serial/option.c. This allows
operation of Huawei E353 broadband modem using the “option” driver. The
patch simply adds new constant with proper product ID and an entry to
usb_device_id. I worked on the 2.6.38.6 sources. Tested on Dell inspiron
1764 (i3 core cpu) and brand new Huawei E353 modem, Fedora 15 beta.
Looking at the type of change, i doubt it has potential to introduce
problems in other parts of kernel or the driver itself.
Signed-off-by: Marcin Galczynski <marcin@galczynski.pl>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
When the USB core wants to change to an alternate interface setting that
doesn't include an active endpoint, or de-configuring the device, the xHCI
driver needs to issue a Configure Endpoint command to tell the host to
drop some endpoints from the schedule. After the command completes, the
xHCI driver needs to free rings for any endpoints that were dropped.
Unfortunately, the xHCI driver wasn't actually freeing the endpoint rings
for dropped endpoints. The rings would be freed if the endpoint's
information was simply changed (and a new ring was installed), but dropped
endpoints never had their rings freed. This caused errors when the ring
segment DMA pool was freed when the xHCI driver was unloaded:
[ 5582.883995] xhci_hcd 0000:06:00.0: dma_pool_destroy xHCI ring segments, ffff88003371d000 busy
[ 5582.884002] xhci_hcd 0000:06:00.0: dma_pool_destroy xHCI ring segments, ffff880033716000 busy
[ 5582.884011] xhci_hcd 0000:06:00.0: dma_pool_destroy xHCI ring segments, ffff880033455000 busy
[ 5582.884018] xhci_hcd 0000:06:00.0: Freed segment pool
[ 5582.884026] xhci_hcd 0000:06:00.0: Freed device context pool
[ 5582.884033] xhci_hcd 0000:06:00.0: Freed small stream array pool
[ 5582.884038] xhci_hcd 0000:06:00.0: Freed medium stream array pool
[ 5582.884048] xhci_hcd 0000:06:00.0: xhci_stop completed - status = 1
[ 5582.884061] xhci_hcd 0000:06:00.0: USB bus 3 deregistered
[ 5582.884193] xhci_hcd 0000:06:00.0: PCI INT A disabled
Fix this issue and free endpoint rings when their endpoints are
successfully dropped.
This patch should be backported to kernels as old as 2.6.31.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
|
|
When an endpoint ring is freed, it is either cached in a per-device ring
cache, or simply freed if the ring cache is full. If the ring was added
to the cache, then virt_dev->num_rings_cached is incremented. The cache
is designed to hold up to 31 endpoint rings, in array indexes 0 to 30.
When the device is freed (when the slot was disabled),
xhci_free_virt_device() is called, it would free the cached rings in
array indexes 0 to virt_dev->num_rings_cached.
Unfortunately, the original code in xhci_free_or_cache_endpoint_ring()
would put the first entry into the ring cache in array index 1, instead of
array index 0. This was caused by the second assignment to rings_cached:
rings_cached = virt_dev->num_rings_cached;
if (rings_cached < XHCI_MAX_RINGS_CACHED) {
virt_dev->num_rings_cached++;
rings_cached = virt_dev->num_rings_cached;
virt_dev->ring_cache[rings_cached] =
virt_dev->eps[ep_index].ring;
This meant that when the device was freed, cached rings with indexes 0 to
N would be freed, and the last cached ring in index N+1 would not be
freed. When the driver was unloaded, this caused interesting messages
like:
xhci_hcd 0000:06:00.0: dma_pool_destroy xHCI ring segments, ffff880063040000 busy
This should be queued to stable kernels back to 2.6.33.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
|
|
Dmitry's patch
dfa49c4ad120a784ef1ff0717168aa79f55a483a USB: xhci - fix math in xhci_get_endpoint_interval()
introduced a bug. The USB 2.0 spec says that full speed isochronous endpoints'
bInterval must be decoded as an exponent to a power of two (e.g. interval =
2^(bInterval - 1)). Full speed interrupt endpoints, on the other hand, don't
use exponents, and the interval in frames is encoded straight into bInterval.
Dmitry's patch was supposed to fix up the full speed isochronous to parse
bInterval as an exponent, but instead it changed the *interrupt* endpoint
bInterval decoding. The isochronous endpoint encoding was the same.
This caused full speed devices with interrupt endpoints (including mice, hubs,
and USB to ethernet devices) to fail under NEC 0.96 xHCI host controllers:
[ 100.909818] xhci_hcd 0000:06:00.0: add ep 0x83, slot id 1, new drop flags = 0x0, new add flags = 0x99, new slot info = 0x38100000
[ 100.909821] xhci_hcd 0000:06:00.0: xhci_check_bandwidth called for udev ffff88011f0ea000
...
[ 100.910187] xhci_hcd 0000:06:00.0: ERROR: unexpected command completion code 0x11.
[ 100.910190] xhci_hcd 0000:06:00.0: xhci_reset_bandwidth called for udev ffff88011f0ea000
When the interrupt endpoint was added and a Configure Endpoint command was
issued to the host, the host controller would return a very odd error message
(0x11 means "Slot Not Enabled", which isn't true because the slot was enabled).
Probably the host controller was getting very confused with the bad encoding.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Dmitry Torokhov <dtor@vmware.com>
Reported-by: Thomas Lindroth <thomas.lindroth@gmail.com>
Tested-by: Thomas Lindroth <thomas.lindroth@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/balbi/usb into usb-next
* 'for-next' of master.kernel.org:/pub/scm/linux/kernel/git/balbi/usb:
MAINTAINERS: tree moved to kernel.org
usb: musb: Calling VBUS pulsing API when SRP is initiated.
usb: otg: TWL6030: OMAP4430: Adding SRP VBUS pulsing API
usb: musb: host: remove duplicate check in musb_ep_program()
usb: musb: export musb_interrupt symbol
usb: musb: allow musb and glue layers to be modules
usb: musb: drop unneeded musb_debug trickery
|
|
composite.c always sets req->length to zero
and expects function driver's setup handlers
to return the amount of bytes to be used
on req->length. If we test against req->length
w_length will always be greater than req->length
thus making us always stall that particular
SEND_ENCAPSULATED_COMMAND request.
Tested against a Windows XP SP3.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
on 9g20 they are the same as the 9260
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Several resources have been allocated before this kmalloc failure, and thus
they should be released in this error handling code, as done in nearby
error handling code.
The semantic match that finds this problem is:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
local idexpression urb;
statement S;
position p1,p2;
@@
urb = usb_alloc_urb@p1(...);
... when != urb
if (urb == NULL) S
... when != urb
(
return <+...urb...+>;
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
cocci.print_main("",p1)
cocci.print_secs("",p2)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Return PTR_ERR(hsotg->clk) instead of -EINVAL if clk_get fails
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch fixes the checkpatch warnings listed below:
WARNING: braces {} are not necessary for any arm of this statement
WARNING: please, no space before tabs
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch fixes the checkpatch error and warning listed below:
ERROR: code indent should use tabs where possible
WARNING: please, no spaces at the start of a line
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
clk_get() returns ERR_PTR() on error, not NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Call VBUS pulsing API when there is SRP initiation from user space.
Signed-off-by: Hema HK <hemahk@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Implement the start_srp API to generate the VBUS pulsing and assign it to
otg_transciever function pointer. This will be used by the link driver when
there is SRP initiation from user.
Signed-off-by: Hema HK <hemahk@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
musb_ep_program() contains obviously duplicate check for 'dma_channel' in its
IN/receive path -- removing it allows to save one level of indentation. While
at it, improve the comment style...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
currently that's used by another module
(am35x) which, granted, it shouldn't be
using that, but in order to avoid compile
errors, let's export that symbol temporarily
until re-factoring work is done on that
driver.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This in part reverts commit 7a180e70cfc56e131bfe4796773df2acfc7d4180.
(usb: musb: temporarily make it bool) and while
at that we also allow glue layers to be compiled
as modules.
There are still some other changes needed
until we can have a fully functional build
with this setup, but we're getting there.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
