| Age | Commit message (Collapse) | Author |
|---|
|
The issue fixed by this patch manifests only then using X11
with mxsfb driver. The X11 will display either shifted image
or otherwise distorted image on the LCD.
The problem is that the X11 tries to reconfigure the framebuffer
and along the way calls fb_ops.fb_set_par() with X11's desired
configuration values. The field of particular interest is
fb_info->var.sync which contains non-standard values if
configured by kernel. These are either FB_SYNC_DATA_ENABLE_HIGH_ACT,
FB_SYNC_DOTCLK_FAILING_ACT or both, depending on the platform
configuration. Both of these values are defined in the
include/linux/mxsfb.h file.
The driver interprets these values and configures the LCD controller
accordingly. Yet X11 only has access to the standard values for this
field defined in include/uapi/linux/fb.h and thus, unlike kernel,
omits these special values. This results in distorted image on the
LCD.
This patch moves these non-standard values into new field of the
mxsfb_platform_data structure so the driver can in turn check this
field instead of the video mode field for these specific portions.
Moreover, this patch prefixes these values with MXSFB_SYNC_ prefix
instead of FB_SYNC_ prefix to prevent confusion of subsequent users.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Linux ARM <linux-arm-kernel@lists.infradead.org>
Cc: Linux FBDEV <linux-fbdev@vger.kernel.org>
Cc: Lothar Waßmann <LW@karo-electronics.de>
Cc: Sascha Hauer <kernel@pengutronix.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Pull ARM SoC fixes from Olof Johansson:
"People are back from the holiday breaks, and it shows. Here are a
bunch of fixes for a number of platforms:
- A couple of small fixes for Nomadik
- A larger set of changes for kirkwood/mvebu
- uart driver selection, dt clocks, gpio-poweroff fixups, a few
__init annotation fixes and some error handling improvement in
their xor dma driver.
- i.MX had a couple of minor fixes (and a critical one for flexcan2
clock setup)
- MXS has a small board fix and a framebuffer bugfix
- A set of fixes for Samsung Exynos, fixing default bootargs and some
Exynos5440 clock issues
- A set of OMAP changes including PM fixes and a few sparse warning
fixups
All in all a bit more positive code delta than we'd ideally want to
see here, mostly from the OMAP PM changes, but nothing overly crazy."
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (44 commits)
ARM: clps711x: Fix bad merge of clockevents setup
ARM: highbank: save and restore L2 cache and GIC on suspend
ARM: highbank: add a power request clear
ARM: highbank: fix secondary boot and hotplug
ARM: highbank: fix typos with hignbank in power request functions
ARM: dts: fix highbank cpu mpidr values
ARM: dts: add device_type prop to cpu nodes on Calxeda platforms
ARM: mx5: Fix MX53 flexcan2 clock
ARM: OMAP2+: am33xx-hwmod: Fix wrongly terminated am33xx_usbss_mpu_irqs array
pinctrl: mvebu: make pdma clock on dove mandatory
ARM: Dove: Add pinctrl clock to DT
dma: mv_xor: fix error handling for clocks
dma: mv_xor: fix error handling of mv_xor_channel_add()
arm: mvebu: Add missing ; for cpu node.
arm: mvebu: Armada XP MV78230 has only three Ethernet interfaces
arm: mvebu: Armada XP MV78230 has two cores, not one
clk: mvebu: Remove inappropriate __init tagging
ARM: Kirkwood: Use fixed-regulator instead of board gpio call
ARM: Kirkwood: Fix missing sdio clock
ARM: Kirkwood: Switch TWSI1 of 88f6282 to DT clock providers
...
|
|
The VDCTRL4 register does not provide the MXS SET/CLR/TOGGLE feature.
The write in mxsfb_disable_controller() sets the data_cnt for the LCD
DMA to 0 which obviously means the max. count for the LCD DMA and
leads to overwriting arbitrary memory when the display is unblanked.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Juergen Beisert <jbe@pengutronix.de>
Tested-by: Lauri Hintsala <lauri.hintsala@bluegiga.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a simple device tree probe support for mxsfb driver. Before
a common binding for struct fb_videomode is available, the driver will
keep using struct mxsfb_platform_data. That said, platform code will
use auxdata to attach mxsfb_platform_data for device tree boot.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Move mxsfb.h into include/linux, so that mxsfb driver does not have to
include <mach/*> header.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Pull fbdev updates from Florian Tobias Schandinat:
- driver for AUO-K1900 and AUO-K1901 epaper controller
- large updates for OMAP (e.g. decouple HDMI audio and video)
- some updates for Exynos and SH Mobile
- various other small fixes and cleanups
* tag 'fbdev-updates-for-3.5' of git://github.com/schandinat/linux-2.6: (130 commits)
video: bfin_adv7393fb: Fix cleanup code
video: exynos_dp: reduce delay time when configuring video setting
video: exynos_dp: move sw reset prioir to enabling sw defined function
video: exynos_dp: use devm_ functions
fb: handle NULL pointers in framebuffer release
OMAPDSS: HDMI: OMAP4: Update IRQ flags for the HPD IRQ request
OMAPDSS: Apply VENC timings even if panel is disabled
OMAPDSS: VENC/DISPC: Delay dividing Y resolution for managers connected to VENC
OMAPDSS: DISPC: Support rotation through TILER
OMAPDSS: VRFB: remove compiler warnings when CONFIG_BUG=n
OMAPFB: remove compiler warnings when CONFIG_BUG=n
OMAPDSS: remove compiler warnings when CONFIG_BUG=n
OMAPDSS: DISPC: fix usage of dispc_ovl_set_accu_uv
OMAPDSS: use DSI_FIFO_BUG workaround only for manual update displays
OMAPDSS: DSI: Support command mode interleaving during video mode blanking periods
OMAPDSS: DISPC: Update Accumulator configuration for chroma plane
drivers/video: fsl-diu-fb: don't initialize the THRESHOLDS registers
video: exynos mipi dsi: support reverse panel type
video: exynos mipi dsi: Properly interpret the interrupt source flags
video: exynos mipi dsi: Avoid races in probe()
...
|
|
Cc: linux-fbdev@vger.kernel.org
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
If there's some traffic on the LCD controller pads, the BootROM has trouble with
sampling the bootmode from these pads. The BootROM usually ends in a loop.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Chen Peter-B29397 <B29397@freescale.com>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Li Frank-B20596 <B20596@freescale.com>
Cc: Lin Tony-B19295 <B19295@freescale.com>
Cc: Linux FBDEV <linux-fbdev@vger.kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Shawn Guo <shawn.guo@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Subodh Nijsure <snijsure@grid-net.com>
Cc: Tony Lin <tony.lin@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Wolfgang Denk <wd@denx.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
* 'fbdev-next' of git://github.com/schandinat/linux-2.6: (175 commits)
module_param: make bool parameters really bool (drivers/video/i810)
Revert "atmel_lcdfb: Adjust HFP calculation so it matches the manual."
OMAPDSS: HDMI: Disable DDC internal pull up
OMAPDSS: HDMI: Move duplicate code from boardfile
OMAPDSS: add OrtusTech COM43H4M10XTC display support
OMAP: DSS2: Support for UMSH-8173MD TFT panel
ASoC: OMAP: HDMI: Move HDMI codec trigger function to generic HDMI driver
OMAPDSS: HDMI: Create function to enable HDMI audio
ASoC: OMAP: HDMI: Correct signature of ASoC functions
ASoC: OMAP: HDMI: Introduce driver data for audio codec
grvga: fix section mismatch warnings
video: s3c-fb: Don't keep device runtime active when open
video: s3c-fb: Hold runtime PM references when touching registers
video: s3c-fb: Take a runtime PM reference when unblanked
video: s3c-fb: Disable runtime PM in error paths from probe
video: s3c-fb: Use s3c_fb_enable() to enable the framebuffer
video: s3c-fb: Make runtime PM functional again
drivers/video: fsl-diu-fb: merge fsl_diu_alloc() into map_video_memory()
drivers/video: fsl-diu-fb: add default platform ops functions
drivers/video: fsl-diu-fb: remove broken reference count enabling the display
...
|
|
The patch converts mxsfb driver to clk_prepare/clk_unprepare by
using helper functions clk_prepare_enable/clk_disable_unprepare.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
The driver should be registered with mxsfb_driver, not with mxsfb_devtype.
This caused obvious null pointer dereference and crash.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Huang Shijie <b32955@freescale.com>
Acked-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
This patch converts the drivers in drivers/video/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Cc: Ben Dooks <ben@simtec.co.uk>
Cc: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Acked-by: Alexey Charkov <alchark@gmail.com>
Acked-by: Damian Hobson-Garcia <dhobsong@igel.co.jp>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
Include linux/module.h to fix below build error:
from drivers/video/mxsfb.c:42:
arch/arm/mach-mxs/include/mach/memory.h:22:1: warning: this is the location of the previous definition
drivers/video/mxsfb.c:574: error: 'THIS_MODULE' undeclared here (not in a function)
drivers/video/mxsfb.c:893: warning: data definition has no type or storage class
drivers/video/mxsfb.c:893: warning: type defaults to 'int' in declaration of 'MODULE_DEVICE_TABLE'
drivers/video/mxsfb.c:893: warning: parameter names (without types) in function declaration
drivers/video/mxsfb.c:917: error: expected declaration specifiers or '...' before string constant
drivers/video/mxsfb.c:917: warning: data definition has no type or storage class
drivers/video/mxsfb.c:917: warning: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
drivers/video/mxsfb.c:917: warning: function declaration isn't a prototype
drivers/video/mxsfb.c:918: error: expected declaration specifiers or '...' before string constant
drivers/video/mxsfb.c:918: warning: data definition has no type or storage class
drivers/video/mxsfb.c:918: warning: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
drivers/video/mxsfb.c:918: warning: function declaration isn't a prototype
drivers/video/mxsfb.c:919: error: expected declaration specifiers or '...' before string constant
drivers/video/mxsfb.c:919: warning: data definition has no type or storage class
drivers/video/mxsfb.c:919: warning: type defaults to 'int' in declaration of 'MODULE_LICENSE'
drivers/video/mxsfb.c:919: warning: function declaration isn't a prototype
make[2]: *** [drivers/video/mxsfb.o] Error 1
make[1]: *** [drivers/video] Error 2
make: *** [drivers] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
changes since v2:
- use v3 and v4 for specifying the ip version instead of i.MX23/28.
This is a better namespace when future versions are added.
- rename mach/fb.h to mach/mxsfb.h
changes since v1:
- Add a LCDC_ prefix to the register names.
- use set/clear registers where appropriate
- protect call to mxsfb_disable_controller() in mxsfb_remove()
with a (host->enabled) as suggested by Lothar Wassmann
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: linux-fbdev@vger.kernel.org
|
