| Age | Commit message (Collapse) | Author |
|---|
|
Pull omapdss build problem fix from Tomi Valkeinen:
"Small fixes for omapdss driver. Most importantly, fixes a build
problem when debugfs or omapdss debug support is turned off, and fixes
a suspend related crash."
This has apparently been annoying rmk for a while..
* tag 'omapdss-for-3.5-rc2' of git://gitorious.org/linux-omap-dss2/linux:
OMAPDSS: fix registration of DPI and SDI devices
OMAPDSS: DSI: Fix bug when calculating LP command interleaving parameters
OMAPDSS: fix bogus WARN_ON in dss_runtime_put()
OMAPDSS: Taal: fix compilation warning
OMAPDSS: fix build when DEBUG_FS or DSS_DEBUG_SUPPORT disabled
|
|
This patch fixes a warning:
drivers/video/omap2/displays/panel-taal.c: In function
‘taal_num_errors_show’:
drivers/video/omap2/displays/panel-taal.c:529: warning: ‘errors’ may be
used uninitialized in this function
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Pull fbdev updates from Florian Tobias Schandinat:
- driver for AUO-K1900 and AUO-K1901 epaper controller
- large updates for OMAP (e.g. decouple HDMI audio and video)
- some updates for Exynos and SH Mobile
- various other small fixes and cleanups
* tag 'fbdev-updates-for-3.5' of git://github.com/schandinat/linux-2.6: (130 commits)
video: bfin_adv7393fb: Fix cleanup code
video: exynos_dp: reduce delay time when configuring video setting
video: exynos_dp: move sw reset prioir to enabling sw defined function
video: exynos_dp: use devm_ functions
fb: handle NULL pointers in framebuffer release
OMAPDSS: HDMI: OMAP4: Update IRQ flags for the HPD IRQ request
OMAPDSS: Apply VENC timings even if panel is disabled
OMAPDSS: VENC/DISPC: Delay dividing Y resolution for managers connected to VENC
OMAPDSS: DISPC: Support rotation through TILER
OMAPDSS: VRFB: remove compiler warnings when CONFIG_BUG=n
OMAPFB: remove compiler warnings when CONFIG_BUG=n
OMAPDSS: remove compiler warnings when CONFIG_BUG=n
OMAPDSS: DISPC: fix usage of dispc_ovl_set_accu_uv
OMAPDSS: use DSI_FIFO_BUG workaround only for manual update displays
OMAPDSS: DSI: Support command mode interleaving during video mode blanking periods
OMAPDSS: DISPC: Update Accumulator configuration for chroma plane
drivers/video: fsl-diu-fb: don't initialize the THRESHOLDS registers
video: exynos mipi dsi: support reverse panel type
video: exynos mipi dsi: Properly interpret the interrupt source flags
video: exynos mipi dsi: Avoid races in probe()
...
|
|
In all these files, the .power field was never correctly initialized.
Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Dave Airlie <airlied@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The Beagleboard xM gpio used for TFP410 powerdown is connected through
an I2C attached chip which means setting the GPIO can sleep. Code that
calls tfp410_power_on/off holds a mutex, so sleeping should be fine.
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
To ease device tree adaptation in the future, rewrite TFP410 platform
data handling to be done inside probe(), so that probe() is the only
place where we need to handle the DT/pdata choice.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Conflicts:
drivers/video/omap2/displays/panel-taal.c
Merge OMAP DSS related board file changes. The branch will also be
merged through linux-omap tree to solve conflicts.
|
|
In preparation for device tree, this patch changes how the DSI pins are
configured. The current configuration method is only doable with board
files and the configuration data is OMAP specific.
This patch moves the configuration data to the panel's platform data,
and the data can easily be given via DT in the future. The configuration
data format is also changed to a generic one which should be suitable
for all platforms.
The new format is an array of pin numbers, where the array items start
from clock + and -, then data1 + and -, and so on. For example:
{
0, // pin num for clock lane +
1, // pin num for clock lane -
2, // pin num for data1 lane +
3, // pin num for data1 lane -
...
}
The pin numbers are translated by the DSI driver and used to configure
the hardware appropriately.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
The reset GPIO for Taal panel driver is currently requested in the
4430sdp board file. This patch moves the gpio request/free into the Taal
driver, where it should be.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
Now that the tfp410 driver has been renamed in the code, this patch
finishes the renaming by renaming the files.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
The driver for the TFP410 DPI-to-DVI chip was named quite badly as "DVI
panel driver". This patch renames the code to use tfp410 name for the
driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
Now that the panel-dvi driver handles the PD (power-down) GPIO, we can
remove the custom PD handling from the board files.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
The driver for the TFP410 chip should handle the power-down signal of
the chip, instead of the current way of handling it in the board files.
This patch adds power_down_gpio into the device's platform data, and
adds the necessary code in the driver to request and handle the GPIO.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Add displays to panel-generic-dpi.c
Prime View PD050VL1 (640 x 480)
Prime View PD104SLF (800 x 600)
Prime View PM070WL4 (800 x 480)
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The EDT ET0500G0DH6 is a 5 inch display. It is
tested on an OMAP3 board.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
This patch adds support for the Mitsubishi display
AA084SB01. This is a 7 inch LVDS display. It is tested with
an OMAP3 board.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
On pandora we use .set_timings to alter refresh rate,
so add .check_timings/.set_timings functions.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
With this we can eliminate some duplicate code in panel drivers.
Also lgphilips-lb035q02, nec-nl8048hl11-01b, picodlp and
tpo-td043mtea1 gain support of reading timings over sysfs.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Since any power on stabilisation delay for the supply itself should be
taken care of transparently by the regulator API when the regulator is
enabled the additional delay that the TPO-TD03MTEA1 driver adds after
that returned should be due to the requirements of the device itself
rather than the supply (the delay is also suspicously long for one for
a regulator to ramp). Correct the comment to avoid misleading people
taking this code as a reference.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
It is possible for regulator_enable() to fail and if it does fail that's
generally a bad sign for anything we try to do with the hardware afterwards
so check for and immediately return an error if regulator_enable() fails.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The TAAL driver contains some regulator support which is currently unused
(the code is there but the one panel supported by the driver doesn't have
any regulators provided). This code mostly looks like an open coded
version of the regulator core bulk API.
The only additional feature is that a voltage range can be set once when
the device is opened, though this is never varied at runtime. The general
expectation is that if the device is not actively managing the voltage of
the device (eg, doing DVFS) then any configuration will be done using the
constraints rather than by drivers, saving them code and ensuring that
they work well with systems where the voltage is not configurable.
If systems are added needing regulator support this can be added back in,
though it should be based on core features rather than open coding things.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
fbdev-next
|
|
Merge v3.3-rc6 to get the latest DSS and OMAP arch fixes.
Conflicts:
arch/arm/mach-omap1/board-innovator.c
drivers/video/omap2/dss/apply.c
|
|
|
|
panel-dvi uses i2c, but the Kconfig didn't have dependency on I2C. Add
it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
Over time better gamma has been determined and tuned with some
equipment so update the defaults. From subjective point of view
dark shades should be better visible.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
During system suspend, at the time DSS is being suspended, SPI is
already suspended and it's clocks are cut. Because of this trying to
communicate with the LCD controller results in a deadlock.
To fix this, split out LCD programming parts of display enable/disable
functions and perform them from SPI PM callbacks instead when system is
being suspended. If the display is just being enabled/disabled, do it
from DSS callbacks as before.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
This patch adds support for Innolux AT080TN52 800x600 panel.
Tested with AM3517 based board.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
This patch converts the drivers in drivers/video/* to use the
module_spi_driver() macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Imre Deak <imre.deak@nokia.com>
Cc: Roger Quadros <roger.quadros@nokia.com>
Cc: Steve Sakoman <steve@sakoman.com>
Cc: Erik Gilling <konkers@android.com>
Cc: Gražvydas Ignotas <notasas@gmail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
Using gpio_request_one can make the code simpler because it can
set the direction and initial value in one shot.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
fbdev-next
|
|
dd data for the OrtusTech COM43H4M10XTC display to the
generic_dpi_panel driver.
CC: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
This patch adds support for Microtip Technologies' UMSH-8173MD 800x480
RGB TFT panel. Tested with an OMAP3 board.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
[tomi.valkeinen@ti.com: changed the panel name string]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Make PICODLP driver on OMAP2_DSS_DPI since it is the display interface it uses.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The display state parameter of omap_dss_device struct is not being set correctly
in the panel driver NEC panel driver panel-nec-nl8048hl11-01b.c. Set the correct
states in the panel's enable/disable/suspend/resume functions.
CC: Erik Gilling <konkers@android.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
In ancient times it was necessary to manually initialize the bus field of an
spi_driver to spi_bus_type. These days this is done in spi_driver_register(),
so we can drop the manual assignment.
The patch was generated using the following coccinelle semantic patch:
// <smpl>
@@
identifier _driver;
@@
struct spi_driver _driver = {
.driver = {
- .bus = &spi_bus_type,
},
};
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
The current code uses dsi_video_mode_enable/disable functions to
enable/disable DISPC output for video mode displays. For command mode
displays we have no notion in the DISPC side of whether the panel is
enabled, except when a dss_mgr_start_update() call is made.
However, to properly maintain the DISPC state in apply.c, we need to
know if a manager used for a manual update display is currently in use.
This patch achieves that by changing dsi_video_mode_enable/disable to
dsi_enable/disable_video_output, which is called by both video and
command mode displays. For video mode displays it starts the actual
pixel stream, as it did before. For command mode displays it doesn't do
anything else than mark that the manager is currently in use.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Partial update for manual update displays has never worked quite well:
* The HW has limitations on the update area, and the x and width need to
be even.
* Showing a part of a scaled overlay causes artifacts.
* Makes the management of dispc very complex
Considering the above points and the fact that partial update is not
used anywhere, this and the following patches remove the partial update
support. This will greatly simplify the following re-write of the apply
mechanism to get proper locking and additional features like fifo-merge.
This patch removes the partial update from the panel-taal.c.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Partial update for manual update displays has never worked quite well:
* The HW has limitations on the update area, and the x and width need to
be even.
* Showing a part of a scaled overlay causes artifacts.
* Makes the management of dispc very complex
Considering the above points and the fact that partial update is not
used anywhere, this and the following patches remove the partial update
support. This will greatly simplify the following re-write of the apply
mechanism to get proper locking and additional features like fifo-merge.
This patch removes the partial update from the dsi.c.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Add data for the FocalTech ETM070003DH6 display to the generic_dpi_panel
display driver.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
fbdev-next
|
|
Compiling panel-picodlp.c failed with:
drivers/video/omap2/displays/panel-picodlp.c:560:12: error:
'THIS_MODULE' undeclared here (not in a function)
Add #include <linux/module.h> to get THIS_MODULE definition.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Since commit [e58aa3d2: genirq: Run irq handlers with interrupts disabled],
We run all interrupt handlers with interrupts disabled
and we even check and yell when an interrupt handler
returns with interrupts enabled (see commit [b738a50a:
genirq: Warn when handler enables interrupts]).
So now this flag is a NOOP and can be removed.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
Four of the LCD panel drivers depend on the backlight class,
so add the dependency in Kconfig.
Selecting the BACKLIGHT_CLASS_DEVICE symbol does not generally
work since it has other dependencies.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[tomi.valkeinen@ti.com: changed also N8x0 panel]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
This is a driver for N800's display, ported from the old omapfb. This is
a slightly lighter version of the driver as not all features of the old
driver can be ported without big changes to DSS2, and also because some
of the HW features used in the old driver are unclear (e.g. the power
management part).
That said, the new driver works fine for basic use.
Architecturally the driver is not as neat as it could be. N800's display
HW consists of a display buffer chip and a panel, and ideally they would
be represented by separate, independent drivers. This is not currently
possible, and this driver contains both buffer chip and panel driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Port the old omapfb panel driver for Apollon to DSS2.
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Port the old omapfb panel driver for H4 to DSS2.
Cc: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Port the old omapfb panel driver for 2430SDP to DSS2.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Taal panel driver supports two kinds of backlight control: 1) using DSI
commands sent to the panel to control the backlight, 2) calling function
pointers going to the board file to control the backlight.
The second option is a bit hacky, and will no longer be needed when the
PWM driver supports the backlight features. After that we can use the
standard PWM backlight driver.
This patch removes the second backlight control mechanism, and adds a
boolean field, use_dsi_backlight, to nokia_dsi_panel_data which the
board file can use to inform whether the panel driver should use DSI
commands to control the backlight.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Remove the "generic" panel config entry, which is not used.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
