Age | Commit message (Collapse) | Author |
|
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (257 commits)
[ARM] Update mach-types
ARM: 5636/1: Move vendor enum to AMBA include
ARM: Fix pfn_valid() for sparse memory
[ARM] orion5x: Add LaCie NAS 2Big Network support
[ARM] pxa/sharpsl_pm: zaurus c3000 aka spitz: fix resume
ARM: 5686/1: at91: Correct AC97 reset line in at91sam9263ek board
ARM: 5640/1: This patch modifies the support of AC97 on the at91sam9263 ek board
ARM: 5689/1: Update default config of HP Jornada 700-series machines
ARM: 5691/1: fix cache aliasing issues between kmap() and kmap_atomic() with highmem
ARM: 5688/1: ks8695_serial: disable_irq() lockup
ARM: 5687/1: fix an oops with highmem
ARM: 5684/1: Add nuc960 platform to w90x900
ARM: 5683/1: Add nuc950 platform to w90x900
ARM: 5682/1: Add cpu.c and dev.c and modify some files of w90p910 platform
ARM: 5626/1: add suspend/resume functions to amba-pl011 serial driver
ARM: 5625/1: fix hard coded 4K resource size in amba bus detection
MMC: MMCI: convert realview MMC to use gpiolib
ARM: 5685/1: Make MMCI driver compile without gpiolib
ARM: implement highpte
ARM: Show FIQ in /proc/interrupts on CONFIG_FIQ
...
Fix up trivial conflict in arch/arm/kernel/signal.c.
It was due to the TIF_NOTIFY_RESUME addition in commit d0420c83f ("KEYS:
Extend TIF_NOTIFY_RESUME to (almost) all architectures") and follow-ups.
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1623 commits)
netxen: update copyright
netxen: fix tx timeout recovery
netxen: fix file firmware leak
netxen: improve pci memory access
netxen: change firmware write size
tg3: Fix return ring size breakage
netxen: build fix for INET=n
cdc-phonet: autoconfigure Phonet address
Phonet: back-end for autoconfigured addresses
Phonet: fix netlink address dump error handling
ipv6: Add IFA_F_DADFAILED flag
net: Add DEVTYPE support for Ethernet based devices
mv643xx_eth.c: remove unused txq_set_wrr()
ucc_geth: Fix hangs after switching from full to half duplex
ucc_geth: Rearrange some code to avoid forward declarations
phy/marvell: Make non-aneg speed/duplex forcing work for 88E1111 PHYs
drivers/net/phy: introduce missing kfree
drivers/net/wan: introduce missing kfree
net: force bridge module(s) to be GPL
Subject: [PATCH] appletalk: Fix skb leak when ipddp interface is not loaded
...
Fixed up trivial conflicts:
- arch/x86/include/asm/socket.h
converted to <asm-generic/socket.h> in the x86 tree. The generic
header has the same new #define's, so that works out fine.
- drivers/net/tun.c
fix conflict between 89f56d1e9 ("tun: reuse struct sock fields") that
switched over to using 'tun->socket.sk' instead of the redundantly
available (and thus removed) 'tun->sk', and 2b980dbd ("lsm: Add hooks
to the TUN driver") which added a new 'tun->sk' use.
Noted in 'next' by Stephen Rothwell.
|
|
|
|
Conflicts:
MAINTAINERS
arch/arm/mm/fault.c
|
|
'w90x900' into devel
|
|
As soon as the framebuffer is registered, our methods may be called by the
kernel. This leads to a crash as xenfb_refresh() gets called before we have
the irq.
Connect to the backend before registering our framebuffer with the kernel.
[ Fixes bug http://bugzilla.kernel.org/show_bug.cgi?id=14059 ]
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
devel-stable
|
|
This patch updates the SuperH Mobile LCDC driver to skip
over disabled channels. Without this patch suspend-to-ram
operation will crash if deferred io is enabled.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
arch/microblaze/include/asm/socket.h
|
|
Recent framebuffer locking patches first made affected systems unbootable,
then the dead-lock has been fixed but as of 2.6.31-rc4 the framebuffer on
mx3 machines doesn't work. Fix this.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Catalin and kmemleak spotted a leak of a VC screen buffer in
vc_allocate() due to the following chain of events:
vc_allocate()
visual_init(init=1)
vc->vc_sw->con_init(init=1)
fbcon_init()
vc_resize()
vc->screen_buf = kmalloc()
vc->screen_buf = kmalloc()
The common way for the VC drivers is to set the screen dimension
parameters manually in the init case and only call vc_resize() for
!init - which allocates a screen buffer according to the new
dimensions.
fbcon instead would do vc_resize() unconditionally and afterwards set
the dimensions manually (again) for !init - i.e. completely upside
down. The vc_resize() allocated buffer would then get lost by
vc_allocate() allocating a fresh one.
Use vc_resize() only for actual resizing to close the leak.
Set the dimensions manually only in initialization mode to remove the
redundant setting in resize mode.
The kmemleak trace from Catalin:
unreferenced object 0xde158000 (size 12288):
comm "Xorg", pid 1439, jiffies 4294961016
hex dump (first 32 bytes):
20 00 20 00 20 00 20 00 20 00 20 00 20 00 20 00 . . . . . . . .
20 00 20 00 20 00 20 00 20 00 20 00 20 00 20 00 . . . . . . . .
backtrace:
[<c006f74b>] __save_stack_trace+0x17/0x1c
[<c006f81d>] create_object+0xcd/0x188
[<c01f5457>] kmemleak_alloc+0x1b/0x3c
[<c006e303>] __kmalloc+0xdb/0xe8
[<c012cc4b>] vc_do_resize+0x73/0x1e0
[<c012cdf1>] vc_resize+0x15/0x18
[<c011afc1>] fbcon_init+0x1f9/0x2b8
[<c0129e87>] visual_init+0x9f/0xdc
[<c012aff3>] vc_allocate+0x7f/0xfc
[<c012b087>] con_open+0x17/0x80
[<c0120e43>] tty_open+0x1f7/0x2e4
[<c0072fa1>] chrdev_open+0x101/0x118
[<c006ffad>] __dentry_open+0x105/0x1cc
[<c00700fd>] nameidata_to_filp+0x2d/0x38
[<c00788cd>] do_filp_open+0x2c1/0x54c
[<c006fdff>] do_sys_open+0x3b/0xb4
Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Tested-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This fixes a bug caused by changing pointers (viafb_mode, viafb_mode1)
assigned by module_param. It reduces driver complexity by not needlessly
changing these vars as they are only read once and removing now
superfluous code.
On unpatched kernels loading viafb with viafb_mode or viafb_mode1 option
used and afterwards unloading it results in:
kernel BUG at mm/slub.c:2926!
invalid opcode: 0000 [#1] PREEMPT
last sysfs file: /sys/devices/virtual/block/loop0/removable
Modules linked in: snd_hda_codec_realtek snd_hda_intel snd_hda_codec
snd_hwdep snd_pcm rtl8187 snd_timer eeprom_93cx6 mmc_block snd soundcore
via_sdmmc fb snd_page_alloc i2c_algo_bit i2c_viapro ehci_hcd uhci_hcd
cfbcopyarea mmc_core cfbimgblt cfbfillrect video output [last unloaded:
viafb]
Pid: 3355, comm: rmmod Not tainted (2.6.31-rc1 #0)
EIP: 0060:[<c106a759>] EFLAGS: 00010246 CPU: 0
EIP is at kfree+0x80/0xda
EAX: c17c2da0 EBX: dc7edbdc ECX: 0000010f EDX: 00000000
ESI: c102c700 EDI: dc7ed8fa EBP: d703ff2c ESP: d703ff20
DS: 007b ES: 007b FS: 0000 GS: 0033 SS: 0068
Process rmmod (pid: 3355, ti=d703e000 task=db1412c0 task.ti=d703e000)
Stack:
dc7edbdc 00000014 00000016 d703ff40 c102c700 dc7f45d4 dc7f45d4 00000880
d703ff4c c103e571 00000000 d703ffac c103e751 66616976 da140062 db89ba80
00000328 d702edf8 db89ba80 d703ff9c c105d0f0 00000200 da14f898 00000014
Call Trace:
[<c102c700>] ? destroy_params+0x1e/0x2b
[<c103e571>] ? free_module+0xa2/0xd7
[<c103e751>] ? sys_delete_module+0x1ab/0x1da
[<c105d0f0>] ? do_munmap+0x20a/0x225
[<c10029b4>] ? sysenter_do_call+0x12/0x26
Code: 10 76 7a 8d 87 00 00 00 40 c1 e8 0c c1 e0 05 03 05 1c 87 41 c1 66 83 38 00 79 03 8b 40 0c 8b 10 84 d2 78 12 66 f7 c2 00 c0 75 04 <0f> 0b eb fe e8 6f 5a fe ff eb 47 8b 55 04 8b 58 0c 9c 5e fa 3b
EIP: [<c106a759>] kfree+0x80/0xda SS:ESP 0068:d703ff20
This is caused by the current code changing the pointers assigned by
module_param. During unload it tries to free the memory the pointers
point at which is now part of an internal structure.
The patch simply avoids changing the pointers. This is okay as they are
read only once during the initialization process.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Scott Fang <ScottFang@viatech.com.cn>
Cc: Joseph Chan <JosephChan@via.com.tw>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix the rotate_ud() function not to crash in case of a font which has not
a width of multiple by 8: The inner loop of the font pixel copy should not
access a bit outside the font memory area. Subtract the shift offset from
the font width will prevent this.
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
This fixes an off-by-one error. Also, use dev_err instead of printk
in probe() function.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fixed off-by-one bug in loop indexes - some elements beyond windows' array
were accessed, which might result in memory access violations when
removing/suspending the device.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Modify atmel LCD driver: atmel_lcdfb for at91sam9g10. This add a clock
management equivalent to at91sam9261.
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
There's some odd bug in gcc-4.2 where it miscompiles a simple loop whent
he loop counter is of type 'unsigned char' and it should count to 128.
The compiler will incorrectly decide that a trivial loop like this:
unsigned char i, ...
for (i = 0; i < 128; i++) {
..
is endless, and will compile it to a single instruction that just
branches to itself.
This was triggered by the addition of '-fno-strict-overflow', and we
could play games with compiler versions and go back to '-fwrapv'
instead, but the trivial way to avoid it is to just make the loop
induction variable be an 'int' instead.
Thanks to Krzysztof Oledzki for reporting and testing and to Troy Moure
for digging through assembler differences and finding it.
Reported-and-tested-by: Krzysztof Oledzki <olel@ans.pl>
Found-by: Troy Moure <twmoure@szypr.net>
Gcc-bug-acked-by: Ian Lance Taylor <iant@google.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: Realview & Versatile: Fix i2c_board_info definitions
[ARM] 5608/1: Updated U300 defconfig
[ARM] 5606/1: Fix ep93xx watchdog driver headers
[ARM] 5594/1: Correct U300 VIC init PM setting
[ARM] 5595/1: ep93xx: missing header in dma-m2p.c
[ARM] Kirkwood: Correct header define
[ARM] pxa: fix ULPI_{DIR,NXT,STP} MFP defines
backlight: fix pwm_bl.c to notify platform code when suspending
[ARM] pxa: use kzalloc() in pxa_init_gpio_chip()
[ARM] pxa: correct I2CPWR clock for pxa3xx
pxamci: correct DMA flow control
ARM: add support for the EET board, based on the i.MX31 pcm037 module
pcm037: add MT9T031 camera support
Armadillo 500 add NAND flash device support (resend).
ARM MXC: Armadillo 500 add NOR flash device support (resend).
mx31: remove duplicated #include
|
|
The connector documentation states that the argument to the callback
function is always a pointer to a struct cn_msg, but rather than encode it
in the API itself, it uses a void pointer everywhere. This doesn't make
much sense to encode the pointer in documentation as it prevents proper C
type checking from occurring and can easily allow people to use the wrong
pointer type. So convert the argument type to an explicit struct cn_msg
pointer.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Users get confused by this driver. It's really a special purpose
embedded driver, and causes a lot of problems if enabled. So hide it
under EMBEDDED by default, and make sure it doesn't get enabled with
the i915 DRM driver.
Dave, I'm hoping you can feed this to Linus through your tree. It's
appropriate for 2.6.31 I think.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
wm97xx_batery: replace driver_data with dev_get_drvdata()
omap: video: remove direct access of driver_data
Sound: remove direct access of driver_data
driver model: fix show/store prototypes in doc.
Firmware: firmware_class, fix lock imbalance
Driver Core: remove BUS_ID_SIZE
sparc: remove driver-core BUS_ID_SIZE
partitions: fix broken uevent_suppress conversion
devres: WARN() and return, don't crash on device_del() of uninitialized device
|
|
dev_set/get_drvdata() should be used instead, as driver_data is going
away.
Cc: Imre Deak <imre.deak@nokia.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Trilok Soni <soni.trilok@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Felipe Contreras <felipe.contreras@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
* Remove smp_lock.h from files which don't need it (including some headers!)
* Add smp_lock.h to files which do need it
* Make smp_lock.h include conditional in hardirq.h
It's needed only for one kernel_locked() usage which is under CONFIG_PREEMPT
This will make hardirq.h inclusion cheaper for every PREEMPT=n config
(which includes allmodconfig/allyesconfig, BTW)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove call to the mx3fb_set_par() and the mx3fb_blank() before the
register_framebuffer().
This fixes a problem with uninitialized the fb_info->mm_lock mutex
introduced by the commit 537a1bf059f " fbdev: add mutex for fb_mmap
locking"
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove call to the fb_set_par() before the register_framebuffer().
This fixes a problem with uninitialized the fb_info->mm_lock mutex
introduced by the commit 537a1bf059f " fbdev: add mutex for fb_mmap
locking"
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6
|
|
Remove not needed locking of the fb_info->mm_lock mutex before a
frambuffer is registered.
This fixes a problem with uninitialized the fb_info->mm_lock mutex
introduced by the commit 537a1bf059f " fbdev: add mutex for fb_mmap
locking"
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove call to the fsl_diu_set_par before the register_framebuffer().
This fixes a problem with uninitialized the fb_info->mm_lock mutex
introduced by the commit 537a1bf059f " fbdev: add mutex for fb_mmap
locking"
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Tested-by: "Kai Jiang" <b18973@freescale.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 5fd29d6ccbc98884569d6f3105aeca70858b3e0f ("printk: clean up
handling of log-levels and newlines") changed printk semantics. printk
lines with multiple KERN_<level> prefixes are no longer emitted as
before the patch.
<level> is now included in the output on each additional use.
Remove all uses of multiple KERN_<level>s in formats.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6
* 'sh/for-2.6.31' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
serial: sh-sci: fix sci interrupt handler
video: hitfb: Move over to dev_pm_ops.
video: hitfb: Convert to framebuffer_alloc().
video: sh_mobile_lcdcfb: Convert to framebuffer_alloc().
sh: add r8a66597 usb0 host to the se7724 board
usb: allow sh7724 to enable on-chip r8a66597
sh-sci: update receive error handling for muxed irqs
sh: define PERF_COUNTER_INDEX_OFFSET.
|
|
This reverts commit 4148df9b0f38bdd362dd91d52076926c11cbe5a9.
Let's hope that the mm_lock initialization is now correct with all
drivers, following Krzysztof's patches.
Requested-by: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove redundant locking by the mm_lock mutex before a second head of
matrox framebuffer is registered.
This fixes a problem with uninitialized the fb_info->mm_lock mutex
introduced by the commit 537a1bf059f " fbdev: add mutex for fb_mmap
locking"
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove redundant call to the matroxfb_update_fix() before matrox
frambuffer is registered.
This fixes a problem with uninitialized the fb_info->mm_lock mutex
introduced by the commit 537a1bf059f " fbdev: add mutex for fb_mmap
locking"
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove redundant call to the w100fb_set_par() before w100 frambuffer is
registered.
This fixes a problem with uninitialized the fb_info->mm_lock mutex
introduced by the commit 537a1bf059f " fbdev: add mutex for fb_mmap
locking"
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove redundant locking of the fb_info->mm_lock mutex before the
frambuffer is registered.
This fixes a problem with uninitialized the fb_info->mm_lock mutex
introduced by the commit 537a1bf059f " fbdev: add mutex for fb_mmap
locking"
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove redundant call to the encode_fix() before i810 frambuffer is
registered.
This fixes a problem with uninitialized the fb_info->mm_lock mutex
introduced by the commit 537a1bf059f " fbdev: add mutex for fb_mmap
locking"
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6 into sh/for-2.6.31
|
|
A trivial update to move hitfb over to dev_pm_ops.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Follows the sh_mobile_lcdcfb change.
Also fixes up a memory leak with cmap allocation.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
All fb_info structures need to be allocated with framebuffer_alloc() due
to special initialization. Switch over to it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This way they'll be properly initialized early enough for users that may
touch them before the framebuffer has been registered.
Drivers that allocate their fb_info structure some other way (like
matrocfb's broken static allocation) need to be fixed up appropriately.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Correct the CLKVAL_F field value of VIDEO MAIN CONTROLLER 0 REGITSTER.
Frame Rate is 1 / [ { (VSPW+1) + (VBPD+1) + (LIINEVAL + 1) + (VFPD+1)
} x {(HSPW+1) + (HBPD +1)
+ (HFPD+1) + (HOZVAL + 1) } x { ( CLKVAL+1 ) / ( Frequency of Clock
source ) } ] and VCLK = Video Clock Source / (CLKVAL +1).
therefore CLKVAL_F should be "CLKVAL_F = Frequency of Clock source / pixel
clock * refresh".
for this, I added refresh value in platform data like below.
static struct s3c_fb_pd_win xxx_fb_win0 = {
/* this is to ensure we use win0 */
.win_mode = {
.refresh = 60,
.pixclock = (66+4+2+480)*(15+5+3+800),
.left_margin = 66,
.right_margin = 2,
.upper_margin = 15,
.lower_margin = 3,
.hsync_len = 4,
.vsync_len = 5,
.xres = 480,
.yres = 800,
},
.max_bpp = 32,
.default_bpp = 24,
};
static struct s3c_fb_platdata xxx_lcd_pdata __initdata = {
.win[0] = &xxx_fb_win0,
.vidcon0 = VIDCON0_VIDOUT_RGB | VIDCON0_PNRMODE_RGB,
.vidcon1 = VIDCON1_INV_HSYNC | VIDCON1_INV_VSYNC
| VIDCON1_INV_VCLK | VIDCON1_INV_VDEN,
.setup_gpio = s5pc1xx_fb_gpio_setup_24bpp,
};
xxx_machine_init()
{
.
.
.
s3c_fb_set_platdata(&xxx_lcd_pdata);
}
platform data defined in machine code should be setting using
s3c_fb_set_platdata().
Signed-off-by: InKi Dae <inki.dae@samsung.com>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove redundant call to the sisfb_get_fix() before sis frambuffer is
registered.
This fixes a problem with uninitialized the fb_info->mm_lock mutex
introduced by the commit 537a1bf059f " fbdev: add mutex for fb_mmap
locking"
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Tested-by: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 537a1bf059fa312355696fa6db80726e655e7f17 (fbdev: add mutex for
fb_mmap locking) introduces a ->mm_lock mutex for protecting smem
assignments. Unfortunately in the case of sm501fb these happen quite
early in the initialization code, well before the mutex_init() that takes
place in register_framebuffer(), leading to:
Badness at kernel/mutex.c:207
Pid : 1, Comm: swapper
CPU : 0 Not tainted (2.6.31-rc1-00284-g529ba0d-dirty #2273)
PC is at __mutex_lock_slowpath+0x72/0x1bc
PR is at __mutex_lock_slowpath+0x66/0x1bc
...
matroxfb appears to have the same issue and has solved it with an early
mutex_init(), so we do the same for sm501fb.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6: (27 commits)
parisc: use generic atomic64 on 32-bit
parisc: superio: fix build breakage
parisc: Fix PCI resource allocation on non-PAT SBA machines
parisc: perf: wire up sys_perf_counter_open
parisc: add task_pt_regs macro
parisc: wire sys_perf_counter_open to sys_ni_syscall
parisc: inventory.c, fix bloated stack frame
parisc: processor.c, fix bloated stack frame
parisc: fix compile warning in mm/init.c
parisc: remove dead code from sys_parisc32.c
parisc: wire up rt_tgsigqueueinfo
parisc: ensure broadcast tlb purge runs single threaded
parisc: fix "delay!" timer handling
parisc: fix mismatched parenthesis in memcpy.c
parisc: Fix gcc 4.4 warning in lba_pci.c
parisc: add parameter to read_cr16()
parisc: decode_exc.c should include kernel.h
parisc: remove obsolete hw_interrupt_type
parisc: fix irq compile bugs in arch/parisc/kernel/irq.c
parisc: advertise PCI devs after "assign_resources"
...
Manually fixed up trivial conflicts in tools/perf/perf.h due to addition
of SH vs HPPA perf-counter support.
|
|
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|