| Age | Commit message (Collapse) | Author |
|---|
|
panel-dvi uses i2c, but the Kconfig didn't have dependency on I2C. Add
it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
Even if the documentation calls this bit "Reserved" it has to be set
to 0 for correct modesetting on IGA1.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: stable@vger.kernel.org
|
|
VX900 can do hardware scaling for both IGAs in contrast to previous
hardware which could do it only for IGA2. This patch ensures that
we set the parameter for IGA2 and not for IGA1. This fixes hardware
scaling on VX900 until we have the infrastructure to support it for
both IGAs.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: stable@vger.kernel.org
|
|
fbdev-for-linus
|
|
The "OMAPDSS: HDMI: PHY burnout fix" commit switched the HDMI driver
over to using a GPIO for plug detect. Unfortunately the ->detect()
method was not also updated, causing HDMI to no longer work for the
omapdrm driver (because it would actually check if a connection was
detected before attempting to enable display).
Signed-off-by: Rob Clark <rob@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
For DSS clock domain to transition from idle to active state. It's necessary
to enable the optional clock DSS_FCLK before we enable the module using the
MODULEMODE bits in the clock domain's CM_DSS_DSS_CLKCTRL register.
This sequence was not followed correctly for the 'dss_hdmi' hwmod and it led
to DSS clock domain not getting out of idle when pm_runtime_get_sync() was
called for hdmi's platform device.
Since the clock domain failed to change it's state to active, the hwmod code
disables any clocks it had enabled before for this hwmod. This led to the clock
'dss_48mhz_clk' gettind disabled.
When hdmi's runtime_resume() op is called, the call to dss_runtime_get()
correctly enables the DSS clock domain this time. However, the clock
'dss_48mhz_clk' is needed for HDMI's PHY to function correctly. Since it was
disabled previously, the driver fails when it tries to enable HDMI's PHY.
Fix this for now by ensuring that dss_runtime_get() is called before we call
pm_runtime_get_sync() for hdmi's platform device. A correct fix for later would
be to modify the DSS related hwmod's mainclks, and also some changes in how
opt clocks are handled in the DSS driver.
This fixes the issue of HDMI not working when it's the default display. The
issue is not seen if any other display is already enabled as the first display
would have correctly enabled the DSS clockdomain.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
When a PMIC is not found, this driver is unable to obtain its
'vdds_dsi_reg' regulator. Even through its initialization function
fails, other code still calls its enable function, which fails to
check whether it has this regulator before asking for it to be enabled.
This fixes the oops, however a better fix would be to sort out the
upper layers to prevent them calling into a module which failed to
initialize.
Unable to handle kernel NULL pointer dereference at virtual address 00000038
pgd = c0004000
[00000038] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT
Modules linked in:
CPU: 0 Not tainted (3.3.0-rc2+ #228)
PC is at regulator_enable+0x10/0x70
LR is at omapdss_dpi_display_enable+0x54/0x15c
pc : [<c01b9a08>] lr : [<c01af994>] psr: 60000013
sp : c181fd90 ip : c181fdb0 fp : c181fdac
r10: c042eff0 r9 : 00000060 r8 : c044a164
r7 : c042c0e4 r6 : c042bd60 r5 : 00000000 r4 : c042bd60
r3 : c084de48 r2 : c181e000 r1 : c042bd60 r0 : 00000000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 10c5387d Table: 80004019 DAC: 00000015
Process swapper (pid: 1, stack limit = 0xc181e2e8)
Stack: (0xc181fd90 to 0xc1820000)
fd80: c001754c c042bd60 00000000 c042bd60
fda0: c181fdcc c181fdb0 c01af994 c01b9a04 c0016104 c042bd60 c042bd60 c044a338
fdc0: c181fdec c181fdd0 c01b5ed0 c01af94c c042bd60 c042bd60 c1aa8000 c1aa8a0c
fde0: c181fe04 c181fdf0 c01b5f54 c01b5ea8 c02fc18c c042bd60 c181fe3c c181fe08
fe00: c01b2a18 c01b5f48 c01aed14 c02fc160 c01df8ec 00000002 c042bd60 00000003
fe20: c042bd60 c1aa8000 c1aa8a0c c042eff8 c181fe84 c181fe40 c01b3874 c01b29fc
fe40: c042eff8 00000000 c042f000 c0449db8 c044ed78 00000000 c181fe74 c042eff8
fe60: c042eff8 c0449db8 c0449db8 c044ed78 00000000 00000000 c181fe94 c181fe88
fe80: c01e452c c01b35e8 c181feb4 c181fe98 c01e2fdc c01e4518 c042eff8 c0449db8
fea0: c0449db8 c181fef0 c181fecc c181feb8 c01e3104 c01e2f48 c042eff8 c042f02c
fec0: c181feec c181fed0 c01e3190 c01e30c0 c01e311c 00000000 c01e311c c0449db8
fee0: c181ff14 c181fef0 c01e1998 c01e3128 c18330a8 c1892290 c04165e8 c0449db8
ff00: c0449db8 c1ab60c0 c181ff24 c181ff18 c01e2e28 c01e194c c181ff54 c181ff28
ff20: c01e2218 c01e2e14 c039afed c181ff38 c04165e8 c041660c c0449db8 00000013
ff40: 00000000 c03ffdb8 c181ff7c c181ff58 c01e384c c01e217c c181ff7c c04165e8
ff60: c041660c c003a37c 00000013 00000000 c181ff8c c181ff80 c01e488c c01e3790
ff80: c181ff9c c181ff90 c03ffdcc c01e484c c181ffdc c181ffa0 c0008798 c03ffdc4
ffa0: c181ffc4 c181ffb0 c0056440 c0187810 c003a37c c04165e8 c041660c c003a37c
ffc0: 00000013 00000000 00000000 00000000 c181fff4 c181ffe0 c03ea284 c0008708
ffe0: 00000000 c03ea208 00000000 c181fff8 c003a37c c03ea214 1073cec0 01f7ee08
Backtrace:
[<c01b99f8>] (regulator_enable+0x0/0x70) from [<c01af994>] (omapdss_dpi_display_enable+0x54/0x15c)
r6:c042bd60 r5:00000000 r4:c042bd60
[<c01af940>] (omapdss_dpi_display_enable+0x0/0x15c) from [<c01b5ed0>] (generic_dpi_panel_power_on+0x34/0x78)
r6:c044a338 r5:c042bd60 r4:c042bd60
[<c01b5e9c>] (generic_dpi_panel_power_on+0x0/0x78) from [<c01b5f54>] (generic_dpi_panel_enable+0x18/0x28)
r7:c1aa8a0c r6:c1aa8000 r5:c042bd60 r4:c042bd60
[<c01b5f3c>] (generic_dpi_panel_enable+0x0/0x28) from [<c01b2a18>] (omapfb_init_display+0x28/0x150)
r4:c042bd60
[<c01b29f0>] (omapfb_init_display+0x0/0x150) from [<c01b3874>] (omapfb_probe+0x298/0x318)
r8:c042eff8 r7:c1aa8a0c r6:c1aa8000 r5:c042bd60 r4:00000003
[<c01b35dc>] (omapfb_probe+0x0/0x318) from [<c01e452c>] (platform_drv_probe+0x20/0x24)
[<c01e450c>] (platform_drv_probe+0x0/0x24) from [<c01e2fdc>] (really_probe+0xa0/0x178)
[<c01e2f3c>] (really_probe+0x0/0x178) from [<c01e3104>] (driver_probe_device+0x50/0x68)
r7:c181fef0 r6:c0449db8 r5:c0449db8 r4:c042eff8
[<c01e30b4>] (driver_probe_device+0x0/0x68) from [<c01e3190>] (__driver_attach+0x74/0x98)
r5:c042f02c r4:c042eff8
[<c01e311c>] (__driver_attach+0x0/0x98) from [<c01e1998>] (bus_for_each_dev+0x58/0x98)
r6:c0449db8 r5:c01e311c r4:00000000
[<c01e1940>] (bus_for_each_dev+0x0/0x98) from [<c01e2e28>] (driver_attach+0x20/0x28)
r7:c1ab60c0 r6:c0449db8 r5:c0449db8 r4:c04165e8
[<c01e2e08>] (driver_attach+0x0/0x28) from [<c01e2218>] (bus_add_driver+0xa8/0x22c)
[<c01e2170>] (bus_add_driver+0x0/0x22c) from [<c01e384c>] (driver_register+0xc8/0x154)
[<c01e3784>] (driver_register+0x0/0x154) from [<c01e488c>] (platform_driver_register+0x4c/0x60)
r8:00000000 r7:00000013 r6:c003a37c r5:c041660c r4:c04165e8
[<c01e4840>] (platform_driver_register+0x0/0x60) from [<c03ffdcc>] (omapfb_init+0x14/0x34)
[<c03ffdb8>] (omapfb_init+0x0/0x34) from [<c0008798>] (do_one_initcall+0x9c/0x164)
[<c00086fc>] (do_one_initcall+0x0/0x164) from [<c03ea284>] (kernel_init+0x7c/0x120)
[<c03ea208>] (kernel_init+0x0/0x120) from [<c003a37c>] (do_exit+0x0/0x2d8)
r5:c03ea208 r4:00000000
Code: e1a0c00d e92dd870 e24cb004 e24dd004 (e5906038)
---[ end trace 9e2474c2e193b223 ]---
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
fbdev fixes for 3.3
It includes:
- compile fix for fsl-diu-fb
- fix for a suspend/resume issue in atmel_lcdfb
- fix for a suspend/resume issue in OMAP
- workaround for a hardware bug to avoid physical damage in OMAP
- really trivial dead code removal in intelfb
* tag 'fbdev-fixes-for-3.3-1' of git://github.com/schandinat/linux-2.6:
atmel_lcdfb: fix usage of CONTRAST_CTR in suspend/resume
intelfb: remove some dead code
drivers/video: compile fixes for fsl-diu-fb.c
OMAPDSS: HDMI: PHY burnout fix
OMAP: 4430SDP/Panda: add HDMI HPD gpio
OMAP: 4430SDP/Panda: setup HDMI GPIO muxes
OMAPDSS: remove wrong HDMI HPD muxing
OMAP: 4430SDP/Panda: rename HPD GPIO to CT_CP_HPD
OMAP: 4430SDP/Panda: use gpio_free_array to free HDMI gpios
OMAPDSS: use sync versions of pm_runtime_put
|
|
An error was existing in the saving of CONTRAST_CTR register
across suspend/resume.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
The goto on the line before means the return is unreachable. The goto
also returns -ENODEV so no changes are needed there.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
fbdev-for-linus
|
|
Fix a compiler errors introduced in:
commit ddd3d905436b572ebadc09dcf2d12ca5b37020a0
Author: Timur Tabi <timur@freescale.com>
drivers/video: fsl-diu-fb: merge all allocated data into one block
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Fix assembler constraint to prevent overeager gcc optimisation
mac_esp: rename irq
mac_scsi: dont enable mac_scsi irq before requesting it
macfb: fix black and white modes
m68k/irq: Remove obsolete IRQ_FLG_* definitions
Fix up trivial conflict in arch/m68k/kernel/process_mm.c as per Geert.
|
|
A hardware bug in the OMAP4 HDMI PHY causes physical damage to the board
if the HDMI PHY is kept powered on when the cable is not connected.
This patch solves the problem by adding hot-plug-detection into the HDMI
IP driver. This is not a real HPD support in the sense that nobody else
than the IP driver gets to know about the HPD events, but is only meant
to fix the HW bug.
The strategy is simple: If the display device is turned off by the user,
the PHY power is set to OFF. When the display device is turned on by the
user, the PHY power is set either to LDOON or TXON, depending on whether
the HDMI cable is connected.
The reason to avoid PHY OFF when the display device is on, but the cable
is disconnected, is that when the PHY is turned OFF, the HDMI IP is not
"ticking" and thus the DISPC does not receive pixel clock from the HDMI
IP. This would, for example, prevent any VSYNCs from happening, and
would thus affect the users of omapdss. By using LDOON when the cable is
disconnected we'll avoid the HW bug, but keep the HDMI working as usual
from the user's point of view.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
omapdss doesn't work properly on system suspend. The problem seems to be
the fact that omapdss uses pm_runtime_put() functions when turning off
the hardware, and when system suspend is in process only sync versions
are allowed.
Using non-sync versions normally and sync versions when suspending would
need rather ugly hacks to convey the information of
suspending/not-suspending to different functions. Optimally the driver
wouldn't even need to care about this, and the PM layer would handle
syncing when suspend is in process.
This patch changes all omapdss's pm_runtime_put calls to
pm_runtime_put_sync. This fixes the suspend problem, and probably the
performance penalty of always using sync versions is negligible.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
|
|
l4f00242t03_probe if regulator_get() fails
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Alberto Panizzo <alberto@amarulasolutions.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We need to write new value if the bit mask fields of new value is not
equal to old value. It does not make sense to write new value only when
all the bit_mask bits are zero.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
macfb won't init in black & white modes since fb_alloc_cmap() no longer
works for zero cmap length. Fix this and also clean up a few printk's and
some stylistic inconsistencies.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (53 commits)
ARM: mach-shmobile: specify CHCLR registers on SH7372
dma: shdma: fix runtime PM: clear channel buffers on reset
dma/imx-sdma: save irq flags when use spin_lock in sdma_tx_submit
dmaengine/ste_dma40: clear LNK on channel startup
dmaengine: intel_mid_dma: remove legacy pm interface
ASoC: mxs: correct 'direction' of device_prep_dma_cyclic
dmaengine: intel_mid_dma: error path fix
dmaengine: intel_mid_dma: locking and freeing fixes
mtd: gpmi-nand: move to dma_transfer_direction
mtd: fix compile error for gpmi-nand
mmc: mxs-mmc: fix the dma_transfer_direction migration
dmaengine: add DMA_TRANS_NONE to dma_transfer_direction
dma: mxs-dma: Don't use CLKGATE bits in CTRL0 to disable DMA channels
dma: mxs-dma: make mxs_dma_prep_slave_sg() multi user safe
dma: mxs-dma: Always leave mxs_dma_init() with the clock disabled.
dma: mxs-dma: fix a typo in comment
DMA: PL330: Remove pm_runtime_xxx calls from pl330 probe/remove
video i.MX IPU: Fix display connections
i.MX IPU DMA: Fix wrong burstsize settings
dmaengine/ste_dma40: allow fixed physical channel
...
Fix up conflicts in drivers/dma/{Kconfig,mxs-dma.c,pl330.c}
The conflicts looked pretty trivial, but I'll ask people to verify them.
|
|
* 'fbdev-next' of git://github.com/schandinat/linux-2.6: (175 commits)
module_param: make bool parameters really bool (drivers/video/i810)
Revert "atmel_lcdfb: Adjust HFP calculation so it matches the manual."
OMAPDSS: HDMI: Disable DDC internal pull up
OMAPDSS: HDMI: Move duplicate code from boardfile
OMAPDSS: add OrtusTech COM43H4M10XTC display support
OMAP: DSS2: Support for UMSH-8173MD TFT panel
ASoC: OMAP: HDMI: Move HDMI codec trigger function to generic HDMI driver
OMAPDSS: HDMI: Create function to enable HDMI audio
ASoC: OMAP: HDMI: Correct signature of ASoC functions
ASoC: OMAP: HDMI: Introduce driver data for audio codec
grvga: fix section mismatch warnings
video: s3c-fb: Don't keep device runtime active when open
video: s3c-fb: Hold runtime PM references when touching registers
video: s3c-fb: Take a runtime PM reference when unblanked
video: s3c-fb: Disable runtime PM in error paths from probe
video: s3c-fb: Use s3c_fb_enable() to enable the framebuffer
video: s3c-fb: Make runtime PM functional again
drivers/video: fsl-diu-fb: merge fsl_diu_alloc() into map_video_memory()
drivers/video: fsl-diu-fb: add default platform ops functions
drivers/video: fsl-diu-fb: remove broken reference count enabling the display
...
|
|
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (119 commits)
MIPS: Delete unused function add_temporary_entry.
MIPS: Set default pci cache line size.
MIPS: Flush huge TLB
MIPS: Octeon: Remove SYS_SUPPORTS_HIGHMEM.
MIPS: Octeon: Add support for OCTEON II PCIe
MIPS: Octeon: Update PCI Latency timer and enable more error reporting.
MIPS: Alchemy: Update cpu-feature-overrides
MIPS: Alchemy: db1200: Improve PB1200 detection.
MIPS: Alchemy: merge Au1000 and Au1300-style IRQ controller code.
MIPS: Alchemy: chain IRQ controllers to MIPS IRQ controller
MIPS: Alchemy: irq: register pm at irq init time
MIPS: Alchemy: Touchscreen support on DB1100
MIPS: Alchemy: Hook up IrDA on DB1000/DB1100
net/irda: convert au1k_ir to platform driver.
MIPS: Alchemy: remove unused board headers
MTD: nand: make au1550nd.c a platform_driver
MIPS: Netlogic: Mark Netlogic chips as SMT capable
MIPS: Netlogic: Add support for XLP 3XX cores
MIPS: Netlogic: Merge some of XLR/XLP wakup code
MIPS: Netlogic: Add default XLP config.
...
Fix up trivial conflicts in arch/mips/kernel/{perf_event_mipsxx.c,
traps.c} and drivers/tty/serial/Makefile
|
|
Autogenerated GPG tag for Rusty D1ADB8F1: 15EE 8D6C AB0E 7F0C F999 BFCB D920 0E6C D1AD B8F1
* tag 'for-linus' of git://github.com/rustyrussell/linux:
module_param: check that bool parameters really are bool.
intelfbdrv.c: bailearly is an int module_param
paride/pcd: fix bool verbose module parameter.
module_param: make bool parameters really bool (drivers & misc)
module_param: make bool parameters really bool (arch)
module_param: make bool parameters really bool (core code)
kernel/async: remove redundant declaration.
printk: fix unnecessary module_param_name.
lirc_parallel: fix module parameter description.
module_param: avoid bool abuse, add bint for special cases.
module_param: check type correctness for module_param_array
modpost: use linker section to generate table.
modpost: use a table rather than a giant if/else statement.
modules: sysfs - export: taint, coresize, initsize
kernel/params: replace DEBUGP with pr_debug
module: replace DEBUGP with pr_debug
module: struct module_ref should contains long fields
module: Fix performance regression on modules with large symbol tables
module: Add comments describing how the "strmap" logic works
Fix up conflicts in scripts/mod/file2alias.c due to the new linker-
generated table approach to adding __mod_*_device_table entries. The
ARM sa11x0 mcp bus needed to be converted to that too.
|
|
Fix the int/bool confusion in there.
drivers/video/nvidia/nvidia.c:1602: warning: return from incompatible pointer type
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
Dan Carpenter points out that it's an int, not a bool:
intelfbdrv.c:818: if (bailearly == 1)
intelfbdrv.c:828: if (bailearly == 2)
intelfbdrv.c:836: if (bailearly == 3)
intelfbdrv.c:842: if (bailearly == 4)
intelfbdrv.c:851: if (bailearly == 5)
intelfbdrv.c:859: if (bailearly == 6)
intelfbdrv.c:866: bailearly > 6 ? bailearly - 6 : 0);
intelfbdrv.c:874: if (bailearly == 18)
intelfbdrv.c:886: if (bailearly == 19)
intelfbdrv.c:893: if (bailearly == 20)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
|
|
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
This reverts commit 5d910426a6e80194a50e33351c91abcad266c809.
Nicolas Ferre <nicolas.ferre@atmel.com> wrote:
"Unfortunately this is not true for all the SoC that embed the
atmel_lcdfb... So I may need to rework this patch but it is certainly
not applicable in the current form."
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
|
|
Andrew elucidates:
- First installmeant of MM. We have a HUGE number of MM patches this
time. It's crazy.
- MAINTAINERS updates
- backlight updates
- leds
- checkpatch updates
- misc ELF stuff
- rtc updates
- reiserfs
- procfs
- some misc other bits
* akpm: (124 commits)
user namespace: make signal.c respect user namespaces
workqueue: make alloc_workqueue() take printf fmt and args for name
procfs: add hidepid= and gid= mount options
procfs: parse mount options
procfs: introduce the /proc/<pid>/map_files/ directory
procfs: make proc_get_link to use dentry instead of inode
signal: add block_sigmask() for adding sigmask to current->blocked
sparc: make SA_NOMASK a synonym of SA_NODEFER
reiserfs: don't lock root inode searching
reiserfs: don't lock journal_init()
reiserfs: delay reiserfs lock until journal initialization
reiserfs: delete comments referring to the BKL
drivers/rtc/interface.c: fix alarm rollover when day or month is out-of-range
drivers/rtc/rtc-twl.c: add DT support for RTC inside twl4030/twl6030
drivers/rtc/: remove redundant spi driver bus initialization
drivers/rtc/rtc-jz4740.c: make jz4740_rtc_driver static
drivers/rtc/rtc-mc13xxx.c: make mc13xxx_rtc_idtable static
rtc: convert drivers/rtc/* to use module_platform_driver()
drivers/rtc/rtc-wm831x.c: convert to devm_kzalloc()
drivers/rtc/rtc-wm831x.c: remove unused period IRQ handler
...
|
|
Should be no functional changes, mainly a reorganisation to support future
work.
[akpm@linux-foundation.org: fix CONFIG_PM=n build]
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Saves some error handling code and eliminates a class of leaks.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The usage of simple_strtoul() or strict_strtoul() is not preferred. Thus,
kstrtoul should be used.
This patch also fixes checkpatch error as follows:
ERROR: space required after that ',' (ctx:VxV)
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
module.h is included twice.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ryan Mallon <rmallon@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch supports regulator power control in the driver. Current ld9040
driver was controlled power on/off sequence by callback function in the
board file. But, by doing this, there's no need to register lcd power
on/off callback function in the board file.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Convert the drivers in drivers/video/backlight/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com> [ep93xx_bl.c]
Cc: Mike Rapoport <mike@compulab.co.il>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Support for the Avionic Design Xanthos backlight device got added in
commit 3b96ea9ef8 ("backlight: Add support for the Avionic Design Xanthos
backlight device."). That support depends on ARCH_PXA_ADX. The code that
should have provided that Kconfig symbol never got submitted. It has
never been possible to even build this driver. Remove it.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
* 'stable/for-linus-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen: (37 commits)
xen/pciback: Expand the warning message to include domain id.
xen/pciback: Fix "device has been assigned to X domain!" warning
xen/pciback: Move the PCI_DEV_FLAGS_ASSIGNED ops to the "[un|]bind"
xen/xenbus: don't reimplement kvasprintf via a fixed size buffer
xenbus: maximum buffer size is XENSTORE_PAYLOAD_MAX
xen/xenbus: Reject replies with payload > XENSTORE_PAYLOAD_MAX.
Xen: consolidate and simplify struct xenbus_driver instantiation
xen-gntalloc: introduce missing kfree
xen/xenbus: Fix compile error - missing header for xen_initial_domain()
xen/netback: Enable netback on HVM guests
xen/grant-table: Support mappings required by blkback
xenbus: Use grant-table wrapper functions
xenbus: Support HVM backends
xen/xenbus-frontend: Fix compile error with randconfig
xen/xenbus-frontend: Make error message more clear
xen/privcmd: Remove unused support for arch specific privcmp mmap
xen: Add xenbus_backend device
xen: Add xenbus device driver
xen: Add privcmd device driver
xen/gntalloc: fix reference counts on multi-page mappings
...
|
|
clock management changes for i.MX
Another simple series related to clock management, this time only for
imx.
* tag 'clk' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: mxs: select HAVE_CLK_PREPARE for clock
clk: add config option HAVE_CLK_PREPARE into Kconfig
ASoC: mxs-saif: convert to clk_prepare/clk_unprepare
video: mxsfb: convert to clk_prepare/clk_unprepare
serial: mxs-auart: convert to clk_prepare/clk_unprepare
net: flexcan: convert to clk_prepare/clk_unprepare
mtd: gpmi-lib: convert to clk_prepare/clk_unprepare
mmc: mxs-mmc: convert to clk_prepare/clk_unprepare
dma: mxs-dma: convert to clk_prepare/clk_unprepare
net: fec: add clk_prepare/clk_unprepare
ARM: mxs: convert platform code to clk_prepare/clk_unprepare
clk: add helper functions clk_prepare_enable and clk_disable_unprepare
Fix up trivial conflicts in drivers/net/ethernet/freescale/fec.c due to
commit 0ebafefcaa7a ("net: fec: add clk_prepare/clk_unprepare") clashing
trivially with commit e163cc97f9ac ("net/fec: fix the .remove code").
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
* 'staging-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (466 commits)
net/hyperv: Add support for jumbo frame up to 64KB
net/hyperv: Add NETVSP protocol version negotiation
net/hyperv: Remove unnecessary kmap_atomic in netvsc driver
staging/rtl8192e: Register against lib80211
staging/rtl8192e: Convert to lib80211_crypt_info
staging/rtl8192e: Convert to lib80211_crypt_data and lib80211_crypt_ops
staging/rtl8192e: Add lib80211.h to rtllib.h
staging/mei: add watchdog device registration wrappers
drm/omap: GEM, deal with cache
staging: vt6656: int.c, int.h: Change return of function to void
staging: usbip: removed unused definitions from header
staging: usbip: removed dead code from receive function
staging:iio: Drop {mark,unmark}_in_use callbacks
staging:iio: Drop buffer mark_param_change callback
staging:iio: Drop the unused buffer enable() and is_enabled() callbacks
staging:iio: Drop buffer busy flag
staging:iio: Make sure a device is only opened once at a time
staging:iio: Disallow modifying buffer size when buffer is enabled
staging:iio: Disallow changing scan elements in all buffered modes
staging:iio: Use iio_buffer_enabled instead of open coding it
...
Fix up conflict in drivers/staging/iio/adc/ad799x_core.c (removal of
module_init due to using module_i2c_driver() helper, next to removal of
MODULE_ALIAS due to using MODULE_DEVICE_TABLE instead).
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (53 commits)
Kconfig: acpi: Fix typo in comment.
misc latin1 to utf8 conversions
devres: Fix a typo in devm_kfree comment
btrfs: free-space-cache.c: remove extra semicolon.
fat: Spelling s/obsolate/obsolete/g
SCSI, pmcraid: Fix spelling error in a pmcraid_err() call
tools/power turbostat: update fields in manpage
mac80211: drop spelling fix
types.h: fix comment spelling for 'architectures'
typo fixes: aera -> area, exntension -> extension
devices.txt: Fix typo of 'VMware'.
sis900: Fix enum typo 'sis900_rx_bufer_status'
decompress_bunzip2: remove invalid vi modeline
treewide: Fix comment and string typo 'bufer'
hyper-v: Update MAINTAINERS
treewide: Fix typos in various parts of the kernel, and fix some comments.
clockevents: drop unknown Kconfig symbol GENERIC_CLOCKEVENTS_MIGR
gpio: Kconfig: drop unknown symbol 'CS5535_GPIO'
leds: Kconfig: Fix typo 'D2NET_V2'
sound: Kconfig: drop unknown symbol ARCH_CLPS7500
...
Fix up trivial conflicts in arch/powerpc/platforms/40x/Kconfig (some new
kconfig additions, close to removed commented-out old ones)
|
|
fbdev-next
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
* 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (73 commits)
arm: fix up some samsung merge sysdev conversion problems
firmware: Fix an oops on reading fw_priv->fw in sysfs loading file
Drivers:hv: Fix a bug in vmbus_driver_unregister()
driver core: remove __must_check from device_create_file
debugfs: add missing #ifdef HAS_IOMEM
arm: time.h: remove device.h #include
driver-core: remove sysdev.h usage.
clockevents: remove sysdev.h
arm: convert sysdev_class to a regular subsystem
arm: leds: convert sysdev_class to a regular subsystem
kobject: remove kset_find_obj_hinted()
m86k: gpio - convert sysdev_class to a regular subsystem
mips: txx9_sram - convert sysdev_class to a regular subsystem
mips: 7segled - convert sysdev_class to a regular subsystem
sh: dma - convert sysdev_class to a regular subsystem
sh: intc - convert sysdev_class to a regular subsystem
power: suspend - convert sysdev_class to a regular subsystem
power: qe_ic - convert sysdev_class to a regular subsystem
power: cmm - convert sysdev_class to a regular subsystem
s390: time - convert sysdev_class to a regular subsystem
...
Fix up conflicts with 'struct sysdev' removal from various platform
drivers that got changed:
- arch/arm/mach-exynos/cpu.c
- arch/arm/mach-exynos/irq-eint.c
- arch/arm/mach-s3c64xx/common.c
- arch/arm/mach-s3c64xx/cpu.c
- arch/arm/mach-s5p64x0/cpu.c
- arch/arm/mach-s5pv210/common.c
- arch/arm/plat-samsung/include/plat/cpu.h
- arch/powerpc/kernel/sysfs.c
and fix up cpu_is_hotpluggable() as per Greg in include/linux/cpu.h
|
|
git://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm
* 'amba-modalias' of git://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
sound: aaci: Enable module alias autogeneration for AMBA drivers
watchdog: sp805: Enable module alias autogeneration for AMBA drivers
fbdev: amba: Enable module alias autogeneration for AMBA drivers
serial: pl011: Enable module alias autogeneration for AMBA drivers
serial: pl010: Enable module alias autogeneration for AMBA drivers
spi: pl022: Enable module alias autogeneration for AMBA drivers
rtc: pl031: Enable module alias autogeneration for AMBA drivers
rtc: pl030: Enable module alias autogeneration for AMBA drivers
mmc: mmci: Enable module alias autogeneration for AMBA drivers
input: ambakmi: Enable module alias autogeneration for AMBA drivers
gpio: pl061: Enable module alias autogeneration for AMBA drivers
dmaengine: pl330: Enable module alias autogeneration for AMBA drivers
dmaengine: pl08x: Enable module alias autogeneration for AMBA drivers
hwrng: nomadik: Enable module alias autogeneration for AMBA drivers
ARM: amba: Auto-generate AMBA driver module aliases during modpost
ARM: amba: Move definition of struct amba_id to mod_devicetable.h
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (185 commits)
powerpc: fix compile error with 85xx/p1010rdb.c
powerpc: fix compile error with 85xx/p1023_rds.c
powerpc/fsl: add MSI support for the Freescale hypervisor
arch/powerpc/sysdev/fsl_rmu.c: introduce missing kfree
powerpc/fsl: Add support for Integrated Flash Controller
powerpc/fsl: update compatiable on fsl 16550 uart nodes
powerpc/85xx: fix PCI and localbus properties in p1022ds.dts
powerpc/85xx: re-enable ePAPR byte channel driver in corenet32_smp_defconfig
powerpc/fsl: Update defconfigs to enable some standard FSL HW features
powerpc: Add TBI PHY node to first MDIO bus
sbc834x: put full compat string in board match check
powerpc/fsl-pci: Allow 64-bit PCIe devices to DMA to any memory address
powerpc: Fix unpaired probe_hcall_entry and probe_hcall_exit
offb: Fix setting of the pseudo-palette for >8bpp
offb: Add palette hack for qemu "standard vga" framebuffer
offb: Fix bug in calculating requested vram size
powerpc/boot: Change the WARN to INFO for boot wrapper overlap message
powerpc/44x: Fix build error on currituck platform
powerpc/boot: Change the load address for the wrapper to fit the kernel
powerpc/44x: Enable CRASH_DUMP for 440x
...
Fix up a trivial conflict in arch/powerpc/include/asm/cputime.h due to
the additional sparse-checking code for cputime_t.
|
|
This resolves the conflict in the arch/arm/mach-s3c64xx/s3c6400.c file,
and it fixes the build error in the arch/x86/kernel/microcode_core.c
file, that the merge did not catch.
The microcode_core.c patch was provided by Stephen Rothwell
<sfr@canb.auug.org.au> who was invaluable in the merge issues involved
with the large sysdev removal process in the driver-core tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
dd data for the OrtusTech COM43H4M10XTC display to the
generic_dpi_panel driver.
CC: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
This patch adds support for Microtip Technologies' UMSH-8173MD 800x480
RGB TFT panel. Tested with an OMAP3 board.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
[tomi.valkeinen@ti.com: changed the panel name string]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The function hdmi_audio_trigger is a callback used by ASoC to stop/start
HDMI audio. Also, it does not perform IP-specific configuration directly.
Hence, it should be placed in the general portion of the HDMI driver,
along with the other ASoC callbacks.
Also, make this function static.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
In order to separate clearly IP-specific code from general DSS code,
a function for OMAP4 audio enable is created. This function is
included in the HDMI IP ops to align with the current implementation
of the DSS HDMI driver. This function is to be used by the ASoC
HDMI audio codec.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
These functions require access to IP-secific data. However, it is not possible
to pass such data as a function argument as such functions have a specific
signature specified by ASoC. Instead, they will have access to the IP-specific
data by calling snd_soc_codec_get_drvdata. The codec driver data is set
at probe time.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
