| Age | Commit message (Collapse) | Author |
|---|
|
On suspend, remember whether we are streaming or not, and at what frame format,
so that on resume, we can start streaming again.
Signed-off-by: Andrew Chew <achew@nvidia.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This is to avoid needing a forward declaration when ov9740_s_power() (in the
subsequent patch) calls ov9740_s_fmt().
Signed-off-by: Andrew Chew <achew@nvidia.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Derive resolution-dependent register settings programmatically.
Signed-off-by: Andrew Chew <achew@nvidia.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Based on vendor feedback, should issue a software reset at start of day.
Also, OV9740_ANALOG_CTRL15 needs to be changed so the sensor does not begin
streaming until it is ready (otherwise, results in a nonsense frame for the
initial frame).
Added a comment on using discontinuous clock.
Finally, OV9740_ISP_CTRL19 needs to be changed to really use YUYV ordering
(the previous value was for VYUY).
Signed-off-by: Andrew Chew <achew@nvidia.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The register width of the ov9740 is 16-bits, so correct the debug print
to reflect this.
Signed-off-by: Andrew Chew <achew@nvidia.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Made all hex number casing use lower-case throughout the entire driver
for consistency.
Signed-off-by: Andrew Chew <achew@nvidia.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This patch is to enable Atmel Image Sensor Interface (ISI) driver support.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This patch removes .enum_input(), .suspend() and .resume() soc-camera
client operations.
Functionality, provided by .enum_input(), if needed, can be implemented
using the v4l2-subdev API.
As for .suspend() and .resume(), the only client driver, implementing
these methods has been mt9m111, and the only host driver, using them
has been pxa-camera. Now that both those drivers have been converted
to the standard subdev .s_power() operation, .suspend() and .resume()
can be removed.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Eliminate soc-camera specific .suspend() and .restore() methods in favour
of the standard v4l2-subdev .s_power() method
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
It is more convenient to propagate the higher level abstraction - the
struct mt9m111 object into functions and then retrieve a pointer to
the i2c client, if needed, than to do the reverse.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
tw9910 is a TV decoder, it doesn't have a tuner. Besides, the
.enum_input soc-camera operation is optional and normally not needed.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
soc_camera core now performs the standard .bytesperline and .sizeimage
calculations internally, no need to duplicate in drivers.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
If the user is requesting too large a frame, instead of failing
select an acceptable geometry, preserving the requested aspect ratio.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
soc-camera specific .suspend() and .resume() methods are deprecated
and should be replaced by the subdev standard .s_power() operation.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The pxa-camera driver only supports progressive video so far. Passing
down to the client the same format, as what the user has requested can
result in interlaced video, even if the client supports both. This
patch avoids such cases.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
soc_camera core now performs the standard .bytesperline and .sizeimage
calculations internally, no need to duplicate in drivers.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
soc_camera core now performs the standard .bytesperline and .sizeimage
calculations internally, no need to duplicate in drivers.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
range
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Whenever a control changes value or state an event is sent to anyone
that subscribed to it.
This functionality is useful for control panels but also for applications
that need to wait for (usually status) controls to change value.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
When an application changes a control you want to generate an event.
However, you want to avoid sending such an event back to the application
(file handle) that caused the change.
Add the filehandle to the various set control functions.
The filehandle isn't used yet, but the control event patches will need
this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
scenarios
It is a bit tricky to handle autogain/gain type scenerios correctly. Such
controls need to be clustered and the V4L2_CTRL_FLAG_UPDATE should be set on
the autofoo controls. In addition, the manual controls should be marked
inactive when the automatic mode is on, and active when the manual mode is on.
This also requires specialized volatile handling.
The chances of drivers doing all these things correctly are pretty remote.
So a new v4l2_ctrl_auto_cluster function was added that takes care of these
issues.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
If you have a cluster of controls that is a mix of volatile and non-volatile
controls, then requesting the value of the volatile control would fail if the
master control of that cluster was non-volatile. The code assumed that the
volatile state of the master control was the same for all other controls in
the cluster.
This is now fixed.
In addition, it was clear from bugs in some drivers that it was confusing that
the ctrl->cur union had to be used in g_volatile_ctrl. Several drivers used the
'new' values instead. The framework was changed so that drivers now set the new
value instead of the current value.
This has an additional benefit as well: the volatile values are now only stored
in the 'new' value, leaving the current value alone. This is useful for
autofoo/foo control clusters where you want to have a 'foo' control act like a
volatile control if 'autofoo' is on, but as a normal control when it is off.
Since with this change the cur value is no longer overwritten when g_volatile_ctrl
is called, you can use it to remember the original 'foo' value. For example:
autofoo = 0, foo = 10 and foo is non-volatile.
Now autofoo is set to 1 and foo is marked volatile. Retrieving the foo value
will get the volatile value. Set autofoo back to 0, which marks foo as non-
volatile again, and retrieving foo will get the old current value of 10.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
To be consistent with v4l2-ioctl.c.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This is required to implement control events and is also needed to allow
for per-filehandle control handlers.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
When applications try to set READ_ONLY controls an error should
be returned. However, when drivers do that it should be accepted.
Those controls could reflect some driver status which the application
can't change but the driver obviously has to be able to change it.
This is needed among others for future HDMI status controls.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The lower-level prepare functions just set error_idx for each control that
might have an error. The high-level functions will override this with
cs->count in the get and set cases. Only try will keep the error_idx.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Add the call_op define to safely call the control ops. This also allows
for controls without any ops such as the 'control class' controls.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Just like the video drivers, the right thing to do is to use
the per-subsystem version control.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Standardize the remaining video drivers to return the API version
for the VIDIOC_QUERYCAP version, instead of a per-driver version.
Those drivers had the version updated more recently or are SoC
drivers. Even so, it doesn't sound a good idea to keep a per-driver
version control, so, let's use the per-subsystem version control
instead.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Instead of handling a per-driver driver version, use the
per-subsystem one.
As reviewed by Jean-Francois Moine <moinejf@free.fr>:
- the 'info' may be simplified:
Reviewed-by: Jean-Francois Moine <moinejf@free.fr>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
uvcvideo doesn't use vidioc_ioctl2. As the API is changing to use
a common version for all drivers, we need to expliticly fix this
driver.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
sn9c102 doesn't use vidioc_ioctl2. As the API is changing to use
a common version for all drivers, we need to expliticly fix this
driver.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
pvrusb2 doesn't use vidioc_ioctl2. As the API is changing to use
a common version for all drivers, we need to expliticly fix this
driver.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
et61x251 doesn't use vidioc_ioctl2. As the API is changing to use
a common version for all drivers, we need to expliticly fix this
driver.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
After discussing with Andy Walls on irc, we've agreed that this
is the best thing to do. No regressions will be introduced, as 3.x.y
is greater then the current versions for cx18 and ivtv.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
After discussing with Hans, change pwc to use the default version
control.
The only version ever used for pwc driver is 10.0.12, due to
commit 2b455db6d456ef2d44808a8377fd3bc832e08317.
Changing it to 3.x.y won't conflict with the old version.
There's no namespace conflicts in any predictable future.
Even on the remote far-away case where we might have a conflict,
it will be on just one specific stable Kernel release (Kernel 10.0.12),
if we ever have such stable release.
So, it is safe and consistent on using 3.x.y numering schema for
it.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
All the modified drivers didn't have any version increment since
Jan, 1 2011. Several of them didn't have any version increment
for a long time, even having new features and important bug fixes
happening.
As we're now filling the QUERYCAP version with the current Kernel
Release, we don't need to maintain a per-driver version control
anymore. So, let's just use the default.
In order to preserve the Kernel module version history, a
KERNEL_VERSION() macro were added to all modified drivers, and
the extraver number were incremented.
I opted to preserve the per-driver version control to a few
pwc, pvrusb2, s2255, s5p-fimc and sh_vou.
A few drivers are still using the legacy way to handle ioctl's.
So, we can't do such change on them, otherwise, they'll break.
Those are: uvc, et61x251 and sn9c102.
The rationale is that the per-driver version control seems to be
actively maintained on those.
Yet, I think that the better for them would be to just use the
default version numbering, instead of doing that by themselves.
While here, removed a few uneeded include linux/version.h
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Both drxd and siano drivers were including linux/version.h without
any reason. Probably, this is due to some compatibility code that
used to exist before having their support added into the Linux
Kernel.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Most drivers don't increase kernel versions as newer features are added or
bug fixes are solved. So, vidioc_querycap returned value for cap->version is
meaningless. Instead of keeping this situation forever, let's add a default
value matching the current Linux version.
Drivers that want to keep their own version control can still do it, as they
can override the default value for cap->version.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The core driver can now operate in either vmalloc or dma-contig modes;
obviously the latter is preferable when it is supported. Default is
currently vmalloc on all platforms; load the module with buffer_mode=1 for
contiguous DMA mode.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The sequence numbers already give that information if user space cares;
this is a frequent occurrence on slower machines, alas.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This was an old debugging thing from years ago. It's only done at
initialization time, but it's still unnecessary; take it out.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Put the includes into a slightly more readable ordering and get rid of a
few unneeded ones.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This is a basic, naive conversion to the videobuf2 infrastructure, removing
a lot of code in the process. For now, we're using vmalloc, which is
suboptimal, but it does match what the cafe driver did before. In the cafe
case, it may have to stay that way just because memory is too tight to do
direct streaming; mmp-camera will be able to do better.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This patch adds the build infra-structure for Davinci
VPBE dislay driver.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
