| Age | Commit message (Collapse) | Author |
|---|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/isdn/i4l/isdn_net.c
fs/cifs/connect.c
|
|
We should release old elevator when change to use a new one.
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
* 'for-linus' of git://git.o-hand.com/linux-mfd:
mfd: Correct WM8350 I2C return code usage
mfd: fix event masking for da9030
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
rtc: rtc-sun4v fixes, revised
sparc: Fix tty compile warnings.
sparc: struct device - replace bus_id with dev_name(), dev_set_name()
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (27 commits)
rtnetlink: propagate error from dev_change_flags in do_setlink()
isdn: remove extra byteswap in isdn_net_ciscohdlck_slarp_send_reply
Phonet: refuse to send bigger than MTU packets
e1000e: fix IPMI traffic
e1000e: fix warn_on reload after phy_id error
phy: fix phy address bug
e100: fix dma error in direction for mapping
igb: use dev_printk instead of printk
qla3xxx: Cleanup: Fix link print statements.
igb: Use device_set_wakeup_enable
e1000: Use device_set_wakeup_enable
e1000e: Use device_set_wakeup_enable
via-velocity: enable perfect filtering for multicast packets
phy: Add support for Marvell 88E1118 PHY
mlx4_en: Pause parameters per port
phylib: fix premature freeing of struct mii_bus
atl1: Do not enumerate options unsupported by chip
atl1e: fix broken multicast by removing unnecessary crc inversion
gianfar: Fix DMA unmap invocations
net/ucc_geth: Fix oops in uec_get_ethtool_stats()
...
|
|
Several netdev share one adapter here.
We use netdev->ml_priv of the netdevs point to the first netdev's priv.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit a144ea4b7a13087081ab5402fa9ad0bcfd249e67 [IPV4]: annotate struct in_ifaddr
Missed this extra byteswap as the isdn inlines hide the htonl inside
put_u32 which causes an extra byteswap on little-endian arches.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If segmentation offload is enabled by the host, we currently allocate
maximum sized packet buffers and pass them to the host. This uses up
20 ring entries, allowing us to supply only 20 packet buffers to the
host with a 256 entry ring. This is a huge overhead when receiving
small packets, and is most keenly felt when receiving MTU sized
packets from off-host.
The VIRTIO_NET_F_MRG_RXBUF feature flag is set by hosts which support
using receive buffers which are smaller than the maximum packet size.
In order to transfer large packets to the guest, the host merges
together multiple receive buffers to form a larger logical buffer.
The number of merged buffers is returned to the guest via a field in
the virtio_net_hdr.
Make use of this support by supplying single page receive buffers to
the host. On receive, we extract the virtio_net_hdr, copy 128 bytes of
the payload to the skb's linear data buffer and adjust the fragment
offset to point to the remaining data. This ensures proper alignment
and allows us to not use any paged data for small packets. If the
payload occupies multiple pages, we simply append those pages as
fragments and free the associated skbs.
This scheme allows us to be efficient in our use of ring entries
while still supporting large packets. Benchmarking using netperf from
an external machine to a guest over a 10Gb/s network shows a 100%
improvement from ~1Gb/s to ~2Gb/s. With a local host->guest benchmark
with GSO disabled on the host side, throughput was seen to increase
from 700Mb/s to 1.7Gb/s.
Based on a patch from Herbert Xu.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (use netdev_priv)
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Seems like an oversight that we have set-tx-csum and set-sg hooked
up, but not set-tso.
Also leads to the strange situation that if you e.g. disable tx-csum,
then tso doesn't get disabled.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Each time we re-fill the recv queue with buffers, we allocate
one too many skbs and free it again when adding fails. We should
recycle the pages allocated in this case.
A previous version of this patch made trim_pages() trim trailing
unused pages from skbs with some paged data, but this actually
caused a barely measurable slowdown.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (use netdev_priv)
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change enables ECC correction for the packet buffer on all 82571
silicon.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some users reported that they have machines with BMCs enabled that cannot
receive IPMI traffic after e1000e is loaded.
http://marc.info/?l=e1000-devel&m=121909039127414&w=2
http://marc.info/?l=e1000-devel&m=121365543823387&w=2
This fixes the issue if they load with the new parameter = 0 by disabling
crc stripping, but leaves the performance feature on for most users.
Based on work done by Hong Zhang.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the driver fails to initialize the first time due to the failure in the
phy_id check the kernel triggers a warn_on on the second try to load the
driver because the driver did not free the msi/x resources in the first
load because of the previous failure in phy_id check.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
make mdio-gpio work with non OpenFirmware gpio implementation.
Aditional changes to mdio-gpio:
- use gpio_request() and gpio_free()
- place irq[] array in struct mdio_gpio_info
- add module description, author and license
- add note about compiling this driver as module
- rename mdc and mdio function (were ugly names)
- change MII to MDIO in bus name
- add __init __exit to module (un)loading functions
- probe fails if no phys added to the bus
- kzalloc bitbang with sizeof(*bitbang)
Changes since v3:
- keep bus naming "%x" to be compatible with existing drivers.
Changes since v2:
- more #ifdefs reduction
- platform driver will be registered on OF platforms also
- unified platform and OF bus_id to phy%i
Changes since v1:
- removed NO_IRQ
- reduced #idefs
Laurent, please test this driver under OF.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reported by Stephen Rothwell:
drivers/net/dm9000.c:1450: error: expected ')' before ';' token
drivers/net/dm9000.c:1455: error: expected ';' before '}' token
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The vendor BSP used for the WM8350 development provided an I2C driver
which incorrectly returned zero on succesful sends rather than the
number of transmitted bytes, an error which was then propagated into the
WM8350 I2C accessors.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
|
|
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
|
|
Commit 0794469da3f7b2093575cbdfc1108308dd3641ce: ("ACPI: struct device -
replace bus_id with dev_name(), dev_set_name()") introduced a bug by
testing 'dev_name(ldev)' instead of 'ldev->bus' for NULL when printing
out the bus information.
So if ldev->bus was NULL, we'd oops.
Reported-and-tested-by: Bruno Prémont <bonbons@linux-vserver.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Len Brown <len.brown@intel.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
PHYID returns 0xffff and not 0xffffffff when not found and in some
case(at91sam9263) 0x0. Maybe this patch could be useful.
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The e100 driver triggers BUG_ON(buf->direction != dir)
by doing pci_map_single(..., PCI_DMA_BIDIRECTIONAL)
and pci_dma_sync_single_for_device(..., PCI_DMA_TODEVICE).
Changing the DMA direction, especially with dmabounce will result
in unexpected behaviour.
Reported-by: Anders Grafstrom <grfstrm@users.sourceforge.net>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use dev_printk() instead of printk() to give a little more context
and use consistent format.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Removed debug print statements and improved conditionals around informational statements.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since dev->power.should_wakeup bit is used by the PCI core to
decide whether the device should wake up the system from sleep
states, set/unset this bit whenever WOL is enabled/disabled using
igb_set_wol(). Accordingly, use device_can_wakeup() for checking
if wake-up is supported by the device.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since dev->power.should_wakeup bit is used by the PCI core to
decide whether the device should wake up the system from sleep
states, set/unset this bit whenever WOL is enabled/disabled using
e1000_set_wol(). Accordingly, use device_can_wakeup() for checking
if wake-up is supported by the device.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since dev->power.should_wakeup bit is used by the PCI core to
decide whether the device should wake up the system from sleep
states, set/unset this bit whenever WOL is enabled/disabled using
e1000_set_wol(). Accordingly, use device_can_wakeup() for checking
if wake-up is supported by the device.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Joey Zhuo <joeyzhuo@via.com.tw>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make pegasus driver not allocate a workqueue until the driver
is bound to some device, which will need that workqueue if
the device is brought up. This conserves resources when the
driver is linked but there's no pegasus device connected.
Also shrink the runtime footprint a smidgeon by moving some
init-only code into its proper section, and move an obnoxious
(frequent and meaningless) message to be debug-only.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netif_carrier_off() is sufficient to stop Tx into the driver. Stopping the Tx
queues is redundant and unnecessary. By the same token, netif_carrier_on()
will be sufficient to re-enable Tx, so waking the queues is unnecessary.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: don't grab devices with no input
HID: fix radio-mr800 hidquirks
HID: fix kworld fm700 radio hidquirks
HID: fix start/stop cycle in usbhid driver
HID: use single threaded work queue for hid_compat
HID: map macbook keys for "Expose" and "Dashboard"
HID: support for new unibody macbooks
HID: fix locking in hidraw_open()
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
pcmcia: ensure correct logging in do_io_probe
pcmcia: add another pata/ide ID
pcmcia: add braces in error path
pcmcia: struct device - replace bus_id with dev_name(), dev_set_name()
pcmcia: setup resource information for pseudo multifunction devices.
pcmcia: fix indentation & braces disagreement - add braces
|
|
This patch will add support for the Marvell 88E1118 PHY which supports gigabit ethernet among other things.
Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before the change the driver reported the same pause parameters
for all the ports, even only one of them was modified.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The file(s) below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
drivers/hwmon/lis3lv02d.c
This patch removes the said #include <version.h>.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6
* 'sh/for-2.6.28' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
serial: sh-sci: Reorder the SCxTDR write after the TDxE clear.
sh: __copy_user function can corrupt the stack in case of exception
sh: Fixed the TMU0 reload value on resume
sh: Don't factor in PAGE_OFFSET for valid_phys_addr_range() check.
sh: early printk port type fix
i2c: fix i2c-sh_mobile rx underrun
sh: Provide a sane valid_phys_addr_range() to prevent TLB reset with PMB.
usb: r8a66597-hcd: fix wrong data access in SuperH on-chip USB
fix sci type for SH7723
serial: sh-sci: fix cannot work SH7723 SCIFA
sh: Handle fixmap TLB eviction more coherently.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rdunlap/linux-docs
* 'doc-subdirs' of git://git.kernel.org/pub/scm/linux/kernel/git/rdunlap/linux-docs:
Create/use more directory structure in the Documentation/ tree.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
V4L/DVB (9624): CVE-2008-5033: fix OOPS on tvaudio when controlling bass/treble
V4L/DVB (9623): tvaudio: Improve debug msg by printing something more human
V4L/DVB (9622): tvaudio: Improve comments and remove a unneeded prototype
V4L/DVB (9621): Avoid writing outside shadow.bytes[] array
V4L/DVB (9620): tvaudio: use a direct reference for chip description
V4L/DVB (9619): tvaudio: update initial comments
V4L/DVB (9618): tvaudio: add additional logic to avoid OOPS
V4L/DVB (9617): tvtime: remove generic_checkmode callback
V4L/DVB (9616): tvaudio: cleanup - group all callbacks together
V4L/DVB (9615): tvaudio: instead of using a magic number, use ARRAY_SIZE
V4L/DVB (9613): tvaudio: fix a memory leak
|
|
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] fix s390x_newuname
[S390] dasd: log sense for fatal errors
[S390] cpu topology: fix locking
[S390] cio: Fix refcount after moving devices.
[S390] ftrace: fix kernel stack backchain walking
[S390] ftrace: disable tracing on idle psw
[S390] lockdep: fix compile bug
[S390] kvm_s390: Fix oops in virtio device detection with "mem="
[S390] sclp: emit error message if assign storage fails
[S390] Fix range for add_active_range() in setup_memory()
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] dpt_i2o: fix transferred data length for scsi_set_resid()
[SCSI] scsi_error regression: Fix idempotent command handling
[SCSI] zfcp: Fix hexdump data in s390dbf traces
[SCSI] zfcp: fix erp timeout cleanup for port open requests
[SCSI] zfcp: Wait for port scan to complete when setting adapter online
[SCSI] zfcp: Fix cast warning
[SCSI] zfcp: Fix request list handling in error path
[SCSI] zfcp: fix mempool usage for status_read requests
[SCSI] zfcp: fix req_list_locking.
[SCSI] zfcp: Dont clear reference from SCSI device to unit
[SCSI] qla2xxx: Update version number to 8.02.01-k9.
[SCSI] qla2xxx: Return a FAILED status when abort mailbox-command fails.
[SCSI] qla2xxx: Do not honour max_vports from firmware for 2G ISPs and below.
[SCSI] qla2xxx: Use pci_disable_rom() to manipulate PCI config space.
[SCSI] qla2xxx: Correct Atmel flash-part handling.
[SCSI] megaraid: fix mega_internal_command oops
|
|
m68k allmodconfig:
| drivers/misc/c2port/core.c: In function 'c2port_reset':
| drivers/misc/c2port/core.c:73: error: dereferencing pointer to incomplete type
| drivers/misc/c2port/core.c: In function 'c2port_strobe_ck':
| drivers/misc/c2port/core.c:91: error: dereferencing pointer to incomplete type
Include <linux/sched.h> to fix it, as m68k's local_irq_enable() needs to know
about struct task_struct.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: improve phantom device detection
|
|
dpt_i2o.c::adpt_i2o_to_scsi() reads the value at (reply+5) which
should contain the length in bytes of the transferred data. This
would be correct if reply was a u32 *. However it is a void * here,
so we need to read the value at (reply+20) instead.
The value at (reply+5) is usually 0xff0000, which is apparently
'large enough' and didn't cause any trouble until 2.6.27 where
commit 427e59f09fdba387547106de7bab980b7fff77be
Author: James Bottomley <James.Bottomley@HansenPartnership.com>
Date: Sat Mar 8 18:24:17 2008 -0600
[SCSI] make use of the residue value
caused this to become visible through e.g. iostat -x .
Signed-off-by: Miquel van Smoorenburg <mikevs@xs4all.net>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
- simplified code
- use platform_driver_probe
- removed locking: it's provided by rtc subsystem
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently libata uses four methods to detect device presence.
1. PHY status if available.
2. TF register R/W test (only promotes presence, never demotes)
3. device signature after reset
4. IDENTIFY failure detection in SFF state machine
Combination of the above works well in most cases but recently there
have been a few reports where a phantom device causes unnecessary
delay during probe. In both cases, PHY status wasn't available. In
one case, it passed #2 and #3 and failed IDENTIFY with ATA_ERR which
didn't qualify as #4. The other failed #2 but as it passed #3 and #4,
it still caused failure.
In both cases, phantom device reported diagnostic failure, so these
cases can be safely worked around by considering any !ATA_DRQ IDENTIFY
failure as NODEV_HINT if diagnostic failure is set.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
|
|
Commit 46abc02175b3c246dd5141d878f565a8725060c9 ("phylib: give mdio
buses a device tree presence") added a call to device_unregister() in
a situation where the caller did not intend for the device to be
freed yet, but apart from just unregistering the device from the
system, device_unregister() does an additional put_device() that is
intended to free it.
The right function to use in this situation is device_del(), which
unregisters the device from the system like device_unregister() does,
but without dropping the reference count an additional time.
Bug report from Bryan Wu <cooloney@kernel.org>.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Of the various WOL options provided in include/linux/ethtool.h, the
L1 NIC supports only magic packet. Remove all options except magic
packet from the atl1 driver.
Signed-off-by: Jay Cliburn <jcliburn@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Inverting the crc after calling ether_crc_le() is unnecessary and breaks
multicast. Remove it.
Tested-by: David Madore <david.madore@ens.fr>
Signed-off-by: Jay Cliburn <jcliburn@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
We weren't unmapping DMA memory, which will break when gianfar gets used
on systems with more than 32-bits of memory. Also, it's just plain wrong.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
p_{tx,rx}_fw_statistics_pram are special: they're available only when
a device is open. If the device is closed, we should just fill the data
with zeroes.
Fixes the following oops:
root@b1:~# ifconfig eth1 down
root@b1:~# ethtool -S eth1
Unable to handle kernel paging request for data at address 0x00000000
Faulting instruction address: 0xc01e1dcc
Oops: Kernel access of bad area, sig: 11 [#1]
[...]
NIP [c01e1dcc] uec_get_ethtool_stats+0x98/0x124
LR [c0287cc8] ethtool_get_stats+0xfc/0x23c
Call Trace:
[cfaadde0] [c0287ca8] ethtool_get_stats+0xdc/0x23c (unreliable)
[cfaade20] [c0288340] dev_ethtool+0x2fc/0x588
[cfaade50] [c0285648] dev_ioctl+0x290/0x33c
[cfaadea0] [c0272238] sock_ioctl+0x80/0x2ec
[cfaadec0] [c00b5ae4] vfs_ioctl+0x40/0xc0
[cfaadee0] [c00b5fa8] do_vfs_ioctl+0x78/0x20c
[cfaadf10] [c00b617c] sys_ioctl+0x40/0x74
[cfaadf40] [c00142d8] ret_from_syscall+0x0/0x38
[...]
---[ end trace b941007b2dfb9759 ]---
Segmentation fault
p.s. While at it, also remove u64 casts, they aren't needed.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
