| Age | Commit message (Collapse) | Author |
|---|
|
* renamed module parameter back to libertas_debug
* change from bit shifts to constants, that way it's easier to look at the
source and specify the libertas_debug=0xXXXX module parameter
* moved module_param from fw.c to main.c, where it belongs better
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The debug output of libertas was either not present or it was overwhelming.
This patch adds the possibility to specify a bitmask for the area of
interest. One should then only get the desired output.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This reduces usb8xxx.ko by 951 bytes (text) and 256 bytes (data)
when PROC_DEBUG isn't defined.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The previous scan fix did not account for scan paths other than set_scan()
that need to do a full scan at once.
Add a "full_scan" parameter to wlan_scan_networks() to control such
behaviour.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Move libertas_wlan_data_rates into wext.c and make it static. wext.c is the
only user of this array.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
For me it looks cleaner, because it removes one level of indirection.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
DEV_NAME_LEN is already defined in defs.h and that is sufficient.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Remove filename from debug output because it's way too long.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Subject says it all.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
rmmod did not remove /sys/kernel/debug/libertas_wireless/eth1/
subscribed_events/high_snr. After I fixed this, I noticed that
it also didn't remove /sys/kernel/debug/libertas_wireless/eth1
as well.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Renames wlan_association_worker into libertas_association_worker
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Scan two channels per each command on set_scan(), then bail out and let
get_scan() continue the scanning work up to the last channel.
This gives time to the firmware so it can go back to the association
channel and keep the connection alive.
Fixes http://dev.laptop.org/ticket/841
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
in the kernel like in uboot
Signed-off-by: Jean-Christian de Rivaz <jc@eclis.ch>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
|
|
SPI writes intermittently drop bytes at end of DMA transfer
http://blackfin.uclinux.org/gf/project/uclinux-dist/tracker/?action=TrackerItemEdit&tracker_item_id=3205
http://blackfin.uclinux.org/gf/project/uclinux-dist/tracker/?action=TrackerItemEdit&tracker_item_id=2892
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
|
|
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
|
|
as the termios info does not stipulate that the former are dependent on the latter
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
|
|
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
|
|
if we get a break signal, we want to ignore framing and parity errors
because those will always be set (by nature of the signal)
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
|
|
so we can now do spaced/marked parity
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
|
|
After SRST, libata used to wait for nsect/lbal to be set to 1/1 for
the slave device. However, some ATAPI devices don't set nsect/lbal
after SRST and the wait itself isn't too useful as we're gonna wait
for !BSY right after that anyway.
Before reset-seq update, nsect/lbal wait failure used to be ignored
and caused 30sec delay during detection. After reset-seq, all
timeouts are considered error conditions making libata fail to detect
such ATAPI devices.
This patch limits nsect/lbal wait to around 100ms. This should give
acceptable behavior to such ATAPI devices while not disturbing the
heavily used code path too much.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
IOMEGA ZIP 250 ATAPI claims MWDMA0 support but fails SETXFERMODE if
asked to configure itself to MWDMA0. Force PIO.
This fixes bugzilla bug#8497.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Calvin Walton <calvin.walton@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The alignment on 64-bit is different for 64-bit values.
Signed-off-by: Dave Airlie <airlied@linux.ie>
|
|
These require that the status page be referenced by a pointer in GTT, rather
than phsyical memory. So, we have the X Server allocate that memory and tell
us the address, instead.
Signed-off-by: Dave Airlie <airlied@linux.ie>
|
|
Signed-off-by: Dave Airlie <airlied@linux.ie>
|
|
INIT_DEV_PARAMS and SET_MULTI_MODE change the device parameters cached
by libata. Re-read IDENTIFY DEVICE info and update the cached device
paramters when seeing these commands.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Always enforce correct DEV bit since we know which drive the command
is targeted. SAT demands to ignore the DEV bit, too.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Map the ATA passthru UDMA protocols to ATA_PROT_DMA.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
support the pass through of PIO multi commands.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Update the ATA passthru protocol numbers according to the new spec.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The controller is not reporting an unlawful type, it is reporting an
invalid type. Illegal specifically means "prohibited by law"
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The ata IRQ ack functions are only used when debugging. Unfortunately
almost every controller that calls them can cause crashes in some
configurations as there are missing checks for bmdma presence.
In addition ata_port_start insists of installing DMA buffers and pad
buffers for controllers regardless. The SFF controllers actually need to
make that decision dynamically at controller setup time and all need the
same helper - so we add ata_sff_port_start. Future patches will switch
the SFF drivers to use this.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Add the MCP73/MCP77 support to ahci driver.
Signed-off-by: Peer Chen <peerchen@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
hw_sata_spd_limit used to be incorrectly initialized to zero instead
of UINT_MAX if SPD is zero in SControl register. This breaks PHY
speed down. Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
For ATA/CFA devices, libata prints out the device model and firmware revision.
Do the same for ATAPI devices.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Most drivers don't seem to fill out the host->irq field, resulting in the
wrong (no) irq being reported at probe time. For example, sil24 on my system:
ata1: SATA max UDMA/100 cmd 0xd00008009001f000 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
ata2: SATA max UDMA/100 cmd 0xd000080090021000 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
Since they're allocated and set up in ata_host_activate(), just save
them away there.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
HITACHI HTS541680J9SA00/SB21C7EP spuriously completes NCQ commands.
Blacklist it for NCQ.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This patch has removed unused variable in pata_ispnp.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Replace invisible character with a space.
The diff looks like this on my terminal:
- <A0>Choose this option if you're using a host-to-host cable
- <A0>with one of these chips.
+ Choose this option if you're using a host-to-host cable
+ with one of these chips.
Reported by: Massimo Maiurana <maiurana@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Massimo Maiurana <maiurana@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Support for configuring RGMII-ID (RGMII with internal delay) mode on the
88e1111 and 88e1145. Ucc_geth on MPC8360EMDS(the main user of ucc_geth)
is broken after changed to use phylib. It is fixed by adding this
internal delay.
Also renamed 88e1111s -> 88e1111 (no references to an 88e1111s part were
found), and fixed some whitespace.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This patch fixes a possible kernel panic due to not checking the vlan group
when processing received VLAN packets and a malfunction in VLAN/hypervisor
registration.
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
NetXen: Add NETXEN prefixes to macros to clean them up.
This is a cleanup patch which adds NETXEN prefix to some stand
alone macro names.
These posed compile errors when NetXen driver was backported to 2.6.9
on PPC architecture as macros like USER_START are defined in file
arch/ppc64/mm/hash_utils.c
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off by: Wen Xiong <wenxiong@us.ibm.com>
Acked-off by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
NetXen: Fix initialization and subsequent ping issue on 3.4.19 firmware
This patch fixes the ping problem seen X/PBlades after the adapter's
firmware was moved to 3.4.19. After configured interface up, ping
failed.
NetXen adapter couldn't accept ARP broadcast packet. Manual addition of
MAC address in the ARP table, made ping work.
NetXen adapter should finish initilization after system boot. But looks
NetXen adapter didn't initilization correctly after system boot up.
So have to re-load the firmware again in probe routine.
Also re-initilization netxen_config_0 and netxen_config_1 registers.
Signed-off by: Wen Xiong <wenxiong@us.ibm.com>
Signed-off by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
http://bugzilla.kernel.org/show_bug.cgi?id=8160
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Currently, ibmveth maintains several rx buffer pools, which can
be modified through sysfs. By default, pools are not allocated by
default such that jumbo frames cannot be supported without first
activating larger rx buffer pools. This results in failures when attempting
to change the mtu. This patch makes ibmveth automatically allocate
these larger buffer pools when the mtu is changed.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
When attempting to activate additional rx buffer pools on an ibmveth interface that
was not yet up, the error below was seen. The patch fixes this by only closing
and opening the interface to activate the resize if the interface is already
opened.
(drivers/net/ibmveth.c:597 ua:30000004) ERROR: h_free_logical_lan failed with fffffffffffffffc, continuing with close
Unable to handle kernel paging request for data at address 0x00000ff8
Faulting instruction address: 0xd0000000002540e0
Oops: Kernel access of bad area, sig: 11 [#1]
SMP NR_CPUS=128 NUMA PSERIES LPAR
Modules linked in: ip6t_REJECT xt_tcpudp ipt_REJECT xt_state iptable_mangle ipta
ble_nat ip_nat iptable_filter ip6table_mangle ip_conntrack nfnetlink ip_tables i
p6table_filter ip6_tables x_tables ipv6 apparmor aamatch_pcre loop dm_mod ibmvet
h sg ibmvscsic sd_mod scsi_mod
NIP: D0000000002540E0 LR: D0000000002540D4 CTR: 80000000001AF404
REGS: c00000001cd27870 TRAP: 0300 Not tainted (2.6.16.46-0.4-ppc64)
MSR: 8000000000009032 <EE,ME,IR,DR> CR: 24242422 XER: 00000007
DAR: 0000000000000FF8, DSISR: 0000000040000000
TASK = c00000001ca7b4e0[1636] 'sh' THREAD: c00000001cd24000 CPU: 0
GPR00: D0000000002540D4 C00000001CD27AF0 D000000000265650 C00000001C936500
GPR04: 8000000000009032 FFFFFFFFFFFFFFFF 0000000000000007 000000000002C2EF
GPR08: FFFFFFFFFFFFFFFF 0000000000000000 C000000000652A10 C000000000652AE0
GPR12: 0000000000004000 C0000000004A3300 00000000100A0000 0000000000000000
GPR16: 00000000100B8808 00000000100C0F60 0000000000000000 0000000010084878
GPR20: 0000000000000000 00000000100C0CB0 00000000100AF498 0000000000000002
GPR24: 00000000100BA488 C00000001C936760 D000000000258DD0 C00000001C936000
GPR28: 0000000000000000 C00000001C936500 D000000000265180 C00000001C936000
NIP [D0000000002540E0] .ibmveth_close+0xc8/0xf4 [ibmveth]
LR [D0000000002540D4] .ibmveth_close+0xbc/0xf4 [ibmveth]
Call Trace:
[C00000001CD27AF0] [D0000000002540D4] .ibmveth_close+0xbc/0xf4 [ibmveth] (unreliable)
[C00000001CD27B80] [D0000000002545FC] .veth_pool_store+0xd0/0x260 [ibmveth]
[C00000001CD27C40] [C00000000012E0E8] .sysfs_write_file+0x118/0x198
[C00000001CD27CF0] [C0000000000CDAF0] .vfs_write+0x130/0x218
[C00000001CD27D90] [C0000000000CE52C] .sys_write+0x4c/0x8c
[C00000001CD27E30] [C00000000000871C] syscall_exit+0x0/0x40
Instruction dump:
419affd8 2fa30000 419e0020 e93d0000 e89e8040 38a00255 e87e81b0 80c90018
48001531 e8410028 e93d00e0 7fa3eb78 <e8090ff8> f81d0430 4bfffdc9 38210090
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6:
OHCI: Fix machine check in ohci_hub_status_data
USB: Fix up bogus bInterval values in endpoint descriptors
USB: cxacru: ignore error trying to start ADSL in atm_start
USB: cxacru: create sysfs attributes in atm_start instead of bind
USB: cxacru: add Documentation file
USB: UNUSUAL_DEV: Sync up some reported devices from Ubuntu
USB: usb gadgets avoid le{16,32}_to_cpup()
usblp: Don't let suspend to kill ->used
USB: set default y for CONFIG_USB_DEVICE_CLASS
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6:
firmware: remove orphaned Email
kobject: use the proper printk level for kobject error
Driver core: kill unused code
Driver core: keep PHYSDEV for old struct class_device
update Documentation/driver-model/platform.txt
|
|
sata_promise uses two different command modes - packet and TF. Packet mode
is intelligent low-overhead mode while TF is the same old taskfile
interface. As with other advanced interface (ahci/sil24),
ATA_TFLAG_POLLING has no effect in packet mode. However, PIO commands are
issued using TF interface in polling mode, so pdc_interrupt() considers
interrupts spurious if ATA_TFLAG_POLLING is set.
This is broken for polling NODATA commands because command is issued using
packet mode but the interrupt handler ignores it due to ATA_TFLAG_POLLING.
Fix pdc_qc_issue_prot() such that ATA/ATAPI NODATA commands are issued
using TF interface if ATA_TFLAG_POLLING is set.
This patch fixes detection failure introduced by polling SETXFERMODE.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Mikael Pettersson <mikpe@it.uu.se>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
__exit function is used by both init and exit routines, so it cannot
be marked __init. (from allyesconfig)
WARNING: drivers/built-in.o(.text+0x9b83cf): Section mismatch: reference to .exit.text: (between 'divasfunc_exit' and 'didd_callback')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Karsten Keil <kkeil@suse.de>
Acked-by: Armin Schindler <armin@melware.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
