summaryrefslogtreecommitdiffstats
path: root/drivers
AgeCommit message (Collapse)Author
2011-07-11iwlagn: separate and enhance the fixed rate fromWey-Yi Guy
For testing purpose, we need better control of msc from user application. Separate the fixed_rate between debugfs and testmode and enforce it. Signed-off-by: Kenny Hsu <kenny.hsu@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-11iwlagn: block regular host commands if driver don't own uCodeWey-Yi Guy
The only host command allow to send to uCode is the one initiated from testmode if testmode is the owner of uCode Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-11iwlagn: allow application own the uCode operationWey-Yi Guy
Since we open the door to allow application control the device behavior through testmode, add command to allow application request the ownership of the uCode Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-11iwlagn: add CMD_ON_DEMAND flag for host command from testmodeWey-Yi Guy
For all the hist command request from testmode, set the CMD_ON_DEMAND flag. this flag will be used later to control the uCode behavior Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-11iwlagn: declare staticWey-Yi Guy
Declare iwl_mac_rssi_callback as "static" Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-11iwlagn: Enable/disable PS poll based on RSSI and BT coex traffic stateMeenakshi Venkataraman
WiFi throughput drops drastically when BT is turned on, BT and WiFi are simultaneously transmitting/receiving traffic. This is particularly true when BT has higher priority over WiFi, and hence the device defers TX frames. The AP assumes that the channel is bad and reduces the data rate, implying longer airtime, which exacerbates the problem further, resulting ultimately in what is popularly called the "death-spiral" phenomenon. The use of PS-poll in such scenarios guarantees a low but consistent throughput. Since the death-spiral phenomenon is observed only when the RSSI is low, use PS-poll only when RSSI is low and disable when high, with a known hysterisis. This feature specifies the high and low thresholds and implements the callbacks registered with mac80211, which will be called when threshold events occur. iwlwifi: dynamic pspoll: optimize rssi monitor code Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-11iwlagn: use bt handler for 2030 and 135 series devicesWey-Yi Guy
For bt combo devices, need to use bt enabled handlers and functions Reported-by: Don Fry <donald.h.fry@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-11iwlagn: remove double level temperature indirect callWey-Yi Guy
No need to do double level indirect call after driver split no functional changes Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-11iwlagn: remove indirection for eeprom_query_addrFry, Donald H
Not needed since the driver split. Eliminate redundant routine. Signed-off-by: Don Fry <donald.h.fry@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-11iwlagn: remove the indirection for iwl_apm_initFry, Donald H
Not needed since the driver split. Signed-off-by: Don Fry <donald.h.fry@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-11iwlagn: remove the indirection for update_chain_flagsFry, Donald H
Not needed since the driver split. Signed-off-by: Don Fry <donald.h.fry@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-11iwlagn: provide heplers to access the transport opsEmmanuel Grumbach
This removes the for priv->trans.ops->... Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-11iwlagn: remove the indirection for the dma channel numWey-Yi Guy
Not needed since the driver split. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-11iwlagn: consolidate the API that sends host commands and move to transportEmmanuel Grumbach
Now, there are only two functions to send a host command: * send_cmd that receives a iwl_host_cmd * send_cmd_pdu that builds the iwl_host_cmd itself and received flags The flags CMD_ASYNC / CMD_SYNC / CMD_WANT_SKB are not changed by the API functions. Kill the unused flags CMD_SIZE_NORMAL / CMD_NO_SKB on the way. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-11iwlagn: remove code duplicationEmmanuel Grumbach
Code duplication was needed during the move, not needed any more. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-11iwlagn: add an API for TX stopEmmanuel Grumbach
Tx stop moves to transport layer. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-11iwlagn: add an API for RX stopEmmanuel Grumbach
Rx stop moves to transport layer. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-11iwlagn: add an API to free the TX contextEmmanuel Grumbach
Tx free functions move to the transport layer. Unify the functions that deal with tx queues and cmd queue. Since the CMD queue is not fully allocated, but uses the q->n_bd / q->window trick, the release flow of TX queue and CMD queue was different. iwlagn_txq_free_tfd receives now the index of the TFD to be freed, which allows to unify the release flow for all the queues. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-11iwlagn: remove the CMD_MAPPED flagEmmanuel Grumbach
It is uneeded since Johannes removed the HUGE flag. The DMA mapping is always held in the same index as the command. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-11Merge branch 'master' of ↵John W. Linville
master.kernel.org:/pub/scm/linux/kernel/git/padovan/bluetooth-next-2.6 Conflicts: net/bluetooth/l2cap_core.c
2011-07-11Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 Conflicts: drivers/net/wireless/ath/ath5k/sysfs.c net/bluetooth/l2cap_core.c net/mac80211/wpa.c
2011-07-08ath9k_htc: Inform stack about tx ack statusRajkumar Manoharan
Recent firmware changes report tx ack status properly to driver. Hence updating ath9k_htc driver capabilities. Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-08ath9k_hw: Remove read-only registers from AR9003 intervalsRajkumar Manoharan
This patch removes read only registers that cause invalid address access and also updates index for measurement filter calibration window size. Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-08ath9k_hw: Disable power detector calibration for AR9003Rajkumar Manoharan
The power detector calibration is disabled because this block doesn't exist in AR9003 based chips and also parallel calibration is enabled otherwise the calibration will never stop. Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-08ath9k_hw: Update AR9003 interval to improve 5G Tx EVMRajkumar Manoharan
The number of temperature reading samples to average during a Tx packet is decreased to 1 from 2 to improve 5G Tx EVM with chain 0-only mode. Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-08ath9k_hw: Disable PAPRD based on paprd_ht20_mask for 5GHzMohammed Shafi Shajakhan
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-08mwifiex: 4-byte alignment in mwifiex_process_sta_txpd()Yogesh Ashok Powar
In XMIT path, the skb that we get from the kernel itself is not aligned with 4-byte boundary on some embedded platforms. Had it not been the presence of tx_pkt_offset field in txpd, 4 byte memory alignment was not possible without memmove of entire skb. And that would have increased MIPS instead of reducing. With this patch few memory cycles can be saved while fetching interface header and txpd structure because of 4 bytes memory alignment. Reported-by: Philip Rakity <prakity@marvell.com> Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com> Tested-by: Philip Rakity <prakity@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-08mwifiex: fix minor issue in debugfs command 'info'Amitkumar Karwar
Debugfs command 'info' shows wrong interface type. The regression occurred due to commit eecd8250e (mwifiex: remove MWIFIEX_BSS_MODE_ macros) in which we replaced MWIFIEX_BSS_MODE_* macros by NL80211_IFTYPE_*, for example, MWIFIEX_BSS_MODE_IBSS (2) --> NL80211_IFTYPE_ADHOC (1) The issue is fixed by swapping static character array used to display interface type information. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-08mwifiex: fix regression in WEP security modeAmitkumar Karwar
Htcapinfo is unnecessarily sent in assoc request in WEP security due to a regression introduced by commit 2be50b8df53 (mwifiex: remove redundant encryption_mode mapping). The issue is fixed in this patch. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-08ath5k: read sc->imask with sc->irqlock heldPavel Roskin
Signed-off-by: Pavel Roskin <proski@gnu.org> sc->imask may change if ath5k_set_current_imask() races against itself. Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-08ath5k: use kstrtoint() to parse numbers coming from sysfsPavel Roskin
Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-08ath5k: fix formatting errors found by checkpatch.plPavel Roskin
Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-08ath5k: fix misplaced or extraneous braces found by checkpatch.plPavel Roskin
Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-08ath5k: use parentheses around macro definitionsPavel Roskin
Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-08ath5k: don't use volatile, it's not neededPavel Roskin
Signed-off-by: Pavel Roskin <proski@gnu.org> The reg variable is only used by __raw_writel() and __raw_readl(), which should guarantee memory access in the right order. Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-08ath5k: use more readable way to clear MAC addressPavel Roskin
Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-08ath5k: use DEFINE_PCI_DEVICE_TABLE in led.c, mark users with __devinitPavel Roskin
Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-08ath5k: use KERN_WARNING in ATH5K_PRINTFPavel Roskin
Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-08ath5k: remove unneeded parentheses after returnPavel Roskin
Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-08ath5k: replace spaces with tabs as suggested by checkpatch.plPavel Roskin
Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-08ath5k: remove PRIV_ENTRY and PRIV_ASSIGN macros, they obfuscate the codePavel Roskin
Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-08carl9170: Implement tx_frames_pending mac80211 callback functionChristian Lamparter
Implementing this callback function will cause mac80211 refrain from going to powersave state when there are still untransmitted TX frames in the queues. Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-08net/b43: don't return IRQ_HANDLED if nothing was doneSebastian Andrzej Siewior
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-08b43: HT-PHY: define dummy TX power functionsRafał Miłecki
Without them we get Oops with NULL pointer Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-08ath9k_htc: do not configure filter before driver is startedRajkumar Manoharan
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-08b43: LCN-PHY: include new PHY in common codeRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-08b43: define firmwares for HT and LCN PHYsRafał Miłecki
We were uploading different firmwares to the hardware until finding responding one. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-08b43: LCN-PHY add place for new PHY supportRafał Miłecki
LCN-PHY was found in 14e4:4727 card. It uses LCN/1 and 0x2064/1 radio. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-08b43: read radio ID on new coresRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-08b43: use radio ID reading code to older cores onlyRafał Miłecki
Newer ones need separated way Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2025-02-14 03:16:22 +0000