summaryrefslogtreecommitdiffstats
path: root/drivers
AgeCommit message (Collapse)Author
2011-07-13slip: remove dead code within the slip initializationMatvejchikov Ilya
This following code contains a dead "if (dev).." block: ... for (i = 0; i < slip_maxdev; i++) { dev = slip_devs[i]; if (dev == NULL) break; } /* Sorry, too many, all slots in use */ if (i >= slip_maxdev) return NULL; if (dev) { sl = netdev_priv(dev); if (test_bit(SLF_INUSE, &sl->flags)) { unregister_netdevice(dev); dev = NULL; slip_devs[i] = NULL; } } ... The reason is that the code starting with "if (dev).." is never called as when we found an empty slot (dev == NULL) we break the loop and "if (dev).." not works eiter the loop ends and we get out with "i >= slip_maxdev". Signed-off-by: Matvejchikov Ilya <matvejchikov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-13slip: remove redundant check slip_devs for NULLMatvejchikov Ilya
As slip_devs is initialized on module load stage there is no reason to check it for NULL anywhere instead of the deinitialization routine because if we can't get enough memory on startup we don't run at all. Signed-off-by: Matvejchikov Ilya <matvejchikov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-13slip: fix MTU comparation operation when reallocating buffersMatvejchikov Ilya
In sl_realloc_bufs() there is no reason to check if the requested MTU greater than or equal to the current MTU value as this function called only when requested MTU not equals to the current value. So, the ">=" operation can be safely replaced with the ">". Signed-off-by: Matvejchikov Ilya <matvejchikov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-13slip: remove redundant NULL-pointer check before calling slhc_freeMatvejchikov Ilya
Signed-off-by: Matvejchikov Ilya <matvejchikov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-13net: Push protocol type directly down to header_ops->cache()David S. Miller
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-12be2net: move to new vlan modelAjit Khaparde
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-12be2net: account for skb allocation failuresEric Dumazet
If we cannot allocate new skbs in RX completion handler, we should increase netdevice rx_dropped counter, not spam console messages. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-12e1000e: use GFP_KERNEL allocations at init timeJeff Kirsher
In process and sleep allowed context, favor GFP_KERNEL allocations over GFP_ATOMIC ones. -v2: fixed checkpatch.pl warnings CC: Eric Dumazet <eric.dumazet@gmail.com> CC: Ben Greear <greearb@candelatech.com> CC: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-12e1000e: Add Jumbo Frame support to 82583 devicesCarolyn Wyborny
This patch adds support for the Jumbo Frames feature on 82583 devices. Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-12netdevice: Kill 'feature' test macros.David S. Miller
Almost all of these have long outstayed their welcome. And for every one of these macros, there are 10 features for which we didn't add macros. Let's just delete them all, and get out of habit of doing things this way. Signed-off-by: David S. Miller <davem@davemloft.net> Acked-by: Stephen Hemminger <shemminger@vyatta.com> Acked-by: Arnd Bergmann <arnd@arndb.de>
2011-07-12lanai: use pci_dev->subsystem_deviceSergei Shtylyov
The driver reads PCI subsystem IDs from the PCI configuration registers while it is already stored by the PCI subsystem in the 'subsystem_device' field of 'struct pci_dev'... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-11drivers/net: static should be at beginning of declarationJesper Juhl
Make sure that the 'static' keywork is at the beginning of declaration for drivers/net/usb/kalmia.c This gets rid of warnings like warning: ‘static’ is not at beginning of declaration when building with -Wold-style-declaration (and/or -Wextra which also enables it). Signed-off-by: Jesper Juhl <jj@chaosbits.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-11e1000e: remove e1000_queue_statsEric Dumazet
struct e1000_queue_stats is not used, lets remove it Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-11ixgbe: Make certain to initialize the fdir_perfect_lock in all casesAlexander Duyck
This fix makes it so that the fdir_perfect_lock is initialized in all cases. This is necessary as the fdir_filter_exit routine will always attempt to take the lock before inspecting the filter table. Reported-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-07-11igb: Add support of SerDes Forced mode for certain hardwareCarolyn Wyborny
This patch changes the serdes link code to support a forced mode for some hardware, based on bit set in EEPROM. Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-07-11igb: Update copyright on all igb driver files.Carolyn Wyborny
This patch updates the copyright on the igb driver files to 2011. Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-07-11igb: Fix lack of flush after register write and before delayCarolyn Wyborny
Register writes followed by a delay are required to have a flush before the delay in order to commit the values to the register. Without the flush, the code following the delay may not function correctly. Reported-by: Tong Ho <tong.ho@ericsson.com> Reported-by: Guenter Roeck <guenter.roeck@ericsson.com> Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-07-09benet: Add missing comma between constant string arrayJoe Perches
Multiple quoted strings are concatenated without comma separators. Make the arrays const while there. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-08Merge branch 'for-davem' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6
2011-07-08bna: use netdev_alloc_skb_ip_align()Eric Dumazet
Some workloads need some headroom (NET_SKB_PAD) to avoid expensive reallocations. Using netdev_alloc_skb_ip_align() instead of bare skb_alloc() brings the NET_IP_ALIGN and the NET_SKB_PAD headroom. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> CC: Rasesh Mody <rmody@brocade.com> CC: Debashis Dutt <ddutt@brocade.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-08ATM: Delete no use FILL_RX_POOLS_IN_BH marcoWang Shaoyan
The macro FILL_RX_POOLS_IN_BH is never been used, in order to avoid the compiler reports error because of the usage of function INIT_WORK, we just delete the marco. Cc: Chas Williams <chas@cmf.nrl.navy.mil> Cc: linux-atm-general@lists.sourceforge.net Signed-off-by: Wang Shaoyan <wangshaoyan.pt@taobao.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-08drivers/net: Omit check for multicast bit in netdev_for_each_mc_addrTobias Klauser
There is no need to check for the address being a multicast address in the netdev_for_each_mc_addr loop, so remove it. This patch covers all remaining network drivers still containing such a check. Cc: Joe Perches <joe@perches.com> Signed-off-by: Tobias Klauser <tklauser@distanz.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-08skge/sky2: change config references to Marvellstephen hemminger
Change references to SysKonnect in Kconfig to Marvell since SysKonnect was acquired by Marvell back in 2002. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-08sky2: version 1.29stephen hemminger
Since new hardware chip support was added bump version. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-08sky2: support for new Optima chipsets (EXPERIMENTAL)stephen hemminger
This is a backport from the vendor driver of support for the newer Optima (Prime and 2) chipsets. It also includes some setup changes for the current Optima chip as well. The code and comments intentionally mirror the vendor sk98lin driver to allow for easier maintenance. Although this adds support for new chip id's, these chip id's are not used by any of the current PCI device id's listed in the driver. The patch is just to get initial infrastructure in place to handle them when they come. I don't have access to any of this hardware to actually test it yet. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-08sky2: use correct Inter Packet Gap at 10/100mbitstephen hemminger
This is another fix picked out of the vendor driver. The IPG value in the serial mode register is supposed to be programmed differently at lower speeds. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-08sky2: force receive checksum when using RSS on some hardware (v2)stephen hemminger
Found when reviewing the vendor driver. Apparently some chip versions require receive checksumming to be enabled in order for RSS to work. Also, if fix_features has to change some settings; put in message in log in similar manner to netdev_fix_features. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-08Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem
2011-07-07rt2x00: Implement tx_frames_pending mac80211 callback function.Gertjan van Wingerde
Implementing this callback function will cause mac80211 refrain from going to powersave state when there are still untransmitted TX frames in the queues. This would exactly mimic the behaviour of the legacy vendor driver which also doesn't go in powersave mode if there are still TX frames that are not transmitted. This should make powersaving and rt2x00 a better couple. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-07rt2x00: Properly identify rt2800usb devices.Gertjan van Wingerde
Sitecom WLA4000 (USB ID 0x0df6:0x0060) is an RT3072 chipset. Sitecom WLA5000 (USB ID 0x0df6:0x0062) is an RT3572 chipset. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-07rt2x00: Add device ID for RT539F device.Gertjan van Wingerde
Reported-by: Wim Vander Schelden <wim@fixnum.org> Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-07rt2x00: Reduce window of a queue's tx lock.Gertjan van Wingerde
Currently a lot of actions that can be done without the queue's tx lock being held are done inside the locked area. Move them out to have a leaner and meaner code that operates while the tx lock is being held. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-07rt2x00: Don't use queue entry as parameter when creating TX descriptor.Gertjan van Wingerde
The functions that create the tx descriptor structure do not operate on a queue entry at all. Signal this fact in the code by not providing a queue entry as a parameter, but the rt2x00 device structure and the skb directly. This patch is a preparation for reducing the time a queue is locked for a tx operation. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-07rt2x00: Serialize TX operations on a queue.Gertjan van Wingerde
The rt2x00 driver gets frequent occurrences of the following error message when operating under load: phy0 -> rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 2. This is caused by simultaneous attempts from mac80211 to send a frame via rt2x00, which are not properly serialized inside rt2x00queue_write_tx_frame, causing the second frame to fail sending with the above mentioned error message. Fix this by introducing a per-queue spinlock to serialize the TX operations on that queue. Reported-by: Andreas Hartmann <andihartmann@01019freenet.de> Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-07bcma: detect PCI core working in hostmodeRafał Miłecki
We must not init it like clientmode one, it would break device (tested by Hauke on BCM4718). Add stub hostmode driver for now. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-07sky2: use GFP_KERNEL allocations at device setupEric Dumazet
In process and sleep allowed context, favor GFP_KERNEL allocations over GFP_ATOMIC ones. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-07bnx2x: Add dcbnl notificationShmulik Ravid
This patch adds a dcbnl notification to the bnx2x. The notification is sent to user mode clients following a change in the dcb negotiated parameters as resolved by the embedded DCBX stack. Signed-off-by: Shmulik Ravid <shmulikr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-07macvtap: macvtapTX zero-copy supportShirley Ma
Only 128 bytes is copied, the rest of data is DMA mapped directly from userspace. Signed-off-by: Shirley Ma <xma@...ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-07gianfar v2: code cleanupsSebastian Poehn
This patch: # improves readability of some gianfar nfc code Signed-off-by: Sebastian Poehn <sebastian.poehn@belden.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-07skge: update versionstephen hemminger
Update version number, and take "New" off the config information since old sk98lin has been gone for a couple years. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-07skge: make support for old Genesis chips optionalstephen hemminger
The GENESIS boards are really old PCI-X boards that are rare. Marvell has dropped support for this hardware and there is no reason for most users to have to have this code. Rather than riddling code with ifdef's make one macro and let the compiler do the dead code elimination. This saves about 15% of the text size. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-07add pci-id for DGE-530Tstephen hemminger
See also: https://bugzilla.kernel.org/show_bug.cgi?id=38862 Reported-by: jameshenderson@ruggedcom.com Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-07skge: cleanup pci id tablestephen hemminger
The PCI table was using mix of defines for device id and hard coded hex values. This patch change it to all hex values. It also adds comments based on the names provided in the vendor driver table. There is NO CHANGE to the actual resulting table. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-07net: fix warning of versioncheckShan Wei
net-next-2.6/drivers/net/bnx2x/bnx2x_sp.c: 19 linux/version.h not needed. net-next-2.6/drivers/net/caif/caif_hsi.c: 9 linux/version.h not needed. Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-06mwifiex: modify SDIO aggregation Tx/Rx buffer sizeAmitkumar Karwar
The SDIO aggregation buffer size has been modified to an optimum value which gives good throughput results. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-06ipw2100: Fix command list for debuggingJean Delvare
There is a stray "undefined" string in the array, get rid of it. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: "John W. Linville" <linville@tuxdriver.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-06iwlwifi: remove unnecessary read of PCI_CAP_ID_EXPJon Mason
The PCIE capability offset is saved during PCI bus walking. It will remove an unnecessary search in the PCI configuration space if this value is referenced instead of reacquiring it. Signed-off-by: Jon Mason <jdmason@kudzu.us> Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-06Merge branch 'for-linville' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/luca/wl12xx
2011-07-06veth: Kill unused tx_droppedEric Dumazet
Followup to commit f82528bc13a (Exclude duplicated checking for iface-up) : We no longer need percpu tx_dropped field. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-05veth: Kill unused code label and code block.David S. Miller
Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2025-01-09 20:34:33 +0000