summaryrefslogtreecommitdiffstats
path: root/drivers
AgeCommit message (Collapse)Author
2008-01-11Pull bugzilla-9627 into release branchLen Brown
2008-01-11Pull bugzilla-9494 into release branchLen Brown
2008-01-11Pull bugzilla-9194 into release branchLen Brown
2008-01-11PM: ACPI and APM must not be enabled at the same timeLen Brown
ACPI and APM used "pm_active" to guarantee that they would not be simultaneously active. But pm_active was recently moved under CONFIG_PM_LEGACY, so that without CONFIG_PM_LEGACY, pm_active became a NOP -- allowing ACPI and APM to both be simultaneously enabled. This caused unpredictable results, including boot hangs. Further, the code under CONFIG_PM_LEGACY is scheduled for removal. So replace pm_active with pm_flags. pm_flags depends only on CONFIG_PM, which is present for both CONFIG_APM and CONFIG_ACPI. http://bugzilla.kernel.org/show_bug.cgi?id=9194 Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
2008-01-11Pull bugzilla-8973 into release branchLen Brown
2008-01-11Pull bugzilla-8171 into release branchLen Brown
2008-01-11Pull bugzilla-5637 into release branchLen Brown
2008-01-11V4L/DVB (7001): av7110: fix section mismatchRandy Dunlap
Fix driver data name to match whitelist of acceptable names that contain pointers init data so that section mismatch warning is placated. Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-01-11V4L/DVB (6999): ivtv: stick to udelay=10 after allHans Verkuil
Using an udelay of 5 seems to result in problems for several people. For now abandon the udelay value of 5 and stick to 10, even though this will mean a longer load time of the cx2584x firmware. Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-01-11loop: fix bad bio_alloc() nr_iovec requestJens Axboe
Don't allocate room for an iovec when it is not needed. Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-01-10[MACVLAN]: Prevent nesting macvlan devicesPatrick McHardy
Don't allow to nest macvlan devices since it will cause lockdep warnings and isn't really useful for anything. Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-10[BLUETOOTH]: Always send explicit hci_ll wake-up acks.Ohad Ben-Cohen
In the (rare) event of simultaneous mutual wake up requests, do send the chip an explicit wake-up ack. This is required for Texas Instruments's BRF6350 chip. Signed-off-by: Ohad Ben-Cohen <ohad@bencohen.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-11ACPI: apply quirk_ich6_lpc_acpi to more ICH8 and ICH9Zhao Yakui
It is important that these resources be reserved to avoid conflicts with well known ACPI registers. Signed-off-by: Zhao Yakui <yakui.zhao@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2008-01-10ACPICA: fix acpi_serialize hang regressionBob Moore
http://bugzilla.kernel.org/show_bug.cgi?id=8171 Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2008-01-10ACPI : Not register gsi for PCI IDE controller in legacy modeAlan Cox
When PCI IDE controller works in legacy mode and no PRT entry is found in ACPI PRT table, OSPM will neither read the irq number from the IDE PCI configuration space nor call the function of acpi_register_gsi to register gsi. http://bugzilla.kernel.org/show_bug.cgi?id=5637 Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Zhao Yakui <yakui.zhao@intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
2008-01-10Merge git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: [CRYPTO] padlock: Fix alignment fault in aes_crypt_copy
2008-01-10Merge branch 'upstream-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev * 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: libata and starting/stopping ATAPI floppy devices sata_sil24: prevent hba lockup when pass-through ATA commands are used Update kernel parameter document for libata DMA mode setting knobs. libata: don't normalize UNKNOWN to NONE after reset libata-pmp: propagate timeout to host link libata-pmp: 4726 hates SRST pata_ixp4xx_cf: fix compilation introduced by ata_port_desc() conversion pata_pdc202xx_old: Further fixups libata-sff: PCI IRQ handling fix sata_qstor: use hardreset instead of softreset
2008-01-10Merge git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: trm290: do hook dma_host_{on,off} methods (take 2) ide: fix cable detection for SATA bridges ide: workaround suspend bug for ACPI IDE
2008-01-10libata and starting/stopping ATAPI floppy devicesOndrej Zary
Prevent libata from starting/stopping non-ATA devices (like ATAPI floppy drives) as they don't seem to like it: sd 1:0:1:0: [sdb] Starting disk ata2.01: configured for PIO2 sd 1:0:1:0: [sdb] Result: hostbyte=0x00 driverbyte=0x08 sd 1:0:1:0: [sdb] Sense Key : 0x2 [current] sd 1:0:1:0: [sdb] ASC=0x3a ASCQ=0x0 Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-01-10trm290: do hook dma_host_{on,off} methods (take 2)Sergei Shtylyov
Using default methods caused the chip's DMA PRD count registers, inadvertently starting DMA! While fixing it, also do: - get rid of the 'ide_' prefixes in several functions for which the prefix in the method's name has been 'ide_' ectomized already; - align the code hooking the IDE DMA methods in init_hwif_trm290()... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-01-10ide: fix cable detection for SATA bridgesGeorge Kibardin
Signed-off-by: George Kibardin <george-kibardin@yandex.ru> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-01-10ide: workaround suspend bug for ACPI IDEShaohua Li
http://bugzilla.kernel.org/show_bug.cgi?id=9673 ACPI _PS3 cause S4 breaks in the second attempt. The system has a _PS3 method for IDE, which will call into SMM mode. Currently we haven't clue why just the second attempt fails, as it's totally in BIOS code, so blacklist the system so far for 2.6.24. A possible suspect is ACPI NVS isn't save/restore, we will revisit the bug after linux does ACPI NVS save/restore. Bart: - fix scripts/checkpatch.pl complaints - const-ify ide_acpi_dmi_table[] Signed-off-by: Shaohua Li <shaohua.li@intel.com> Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Reported-by: Mikko Vinni <mmvinni@yahoo.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-01-10sata_sil24: prevent hba lockup when pass-through ATA commands are usedGwendal Grignou
Fix commands timeout with Sil3124/3132 based HBA when pass-through ATA commands [where ATA_QCFLAG_RESULT_TF is set] are used while other commands are active on other devices connected to the same port with a Port Multiplier. Due to a hardware bug, these commands must be sent alone, like ATAPI commands. Signed-off-by: Gwendal Grignou <gwendal@google.com> Acked-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-10libata: don't normalize UNKNOWN to NONE after resetTejun Heo
After non-classifying reset, ehc->classes[] could contain ATA_DEV_UNKNOWN which used to be normalized to ATA_DEV_NONE for consistency. However, this causes unfortunate side effect for drivers which have non-classifying hardresets (e.g. sata_nv) by making hardreset report ATA_DEV_NONE for non-classifying resets and thus makes EH believe that the port is unoccupied and recovery can be skipped. The end result is that after a device is swapped with another one, the new device isn't attached after the old one is detached. This patch makes ata_eh_reset() not normalize UNKNOWN to NONE after non-classifying resets. This fixes the above problem. As UNKNOWN and NONE are handled differently by only EH hotplug logic, this doesn't cause other behavior changes. Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Robert Hancock <hancockr@shaw.ca> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-10libata-pmp: propagate timeout to host linkTejun Heo
Timeout on downstream command may indicate transmission problem on host link. Propagate timeouts to host link. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-10libata-pmp: 4726 hates SRSTTejun Heo
4726 hates SRST even on non-config ports. Don't use it. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-10pata_ixp4xx_cf: fix compilation introduced by ata_port_desc() conversionRod Whitby
Fixes a compilation error caused by ata_port_desc() conversion (cbcdd87593a1d85c5c4b259945a3a09eee12814d). Signed-off-by: Rod Whitby <rod@whitby.id.au> Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-10pata_pdc202xx_old: Further fixupsAlan Cox
Turns out distros always enabled burst mode and it is pretty essential so do the same. Also sort out the post DMA mode restore properly. My 20263 card now seems happy but needs some four drive tests done yet (when I've persuaded the kernel not to hang in the edd boot code if I plug them in ..) Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-10libata-sff: PCI IRQ handling fixAlan Cox
It is legitimate (although annoying and silly) for a PCI IDE controller not to be assigned an interrupt and to be polled. The libata-sff code should therefore not try and request IRQ 0 in this case. Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-10sata_qstor: use hardreset instead of softresetTejun Heo
During conversion to new EH, sata_qstor was accidentaly changed to use softreset, which is buggy on this chip, instead of hardreset. This patch updates sata_qstor such that it uses hardreset again. This fixes bugzilla bug 9631. Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-10rt2x00: Put 802.11 data on 4 byte boundaryIvo van Doorn
Check the size of the ieee80211 header during rxdone and make sure the data behind the ieee80211 header is placed on a 4 byte boundary. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-10rt2x00: Corectly initialize rt2500usb MACIvo van Doorn
mac is a pointer, obviously we shouldn't use the address of a pointer as MAC address. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-10rt2x00: Allow rt61 to catch up after a missing tx reportMattias Nissler
Sometimes it happens in the tx path that an entry given to the hardware isn't reported in the txdone handler. This ultimately led to the dreaded "non-free entry in the non-full queue" message and the stopping of the tx queue. Work around this issue by allowing the driver to also clear out previos entries in the txdone handler. Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-11[CRYPTO] padlock: Fix alignment fault in aes_crypt_copyHerbert Xu
The previous patch fixed spurious read faults from occuring by copying the data if we happen to have a single block at the end of a page. It appears that gcc cannot guarantee 16-byte alignment in the kernel with __attribute__. The following report from Torben Viets shows a buffer that's only 8-byte aligned: > eneral protection fault: 0000 [#1] > Modules linked in: xt_TCPMSS xt_tcpmss iptable_mangle ipt_MASQUERADE > xt_tcpudp xt_mark xt_state iptable_nat nf_nat nf_conntrack_ipv4 > iptable_filter ip_tables x_tables pppoe pppox af_packet ppp_generic slhc > aes_i586 > CPU: 0 > EIP: 0060:[<c035b828>] Not tainted VLI > EFLAGS: 00010292 (2.6.23.12 #7) > EIP is at aes_crypt_copy+0x28/0x40 > eax: f7639ff0 ebx: f6c24050 ecx: 00000001 edx: f6c24030 > esi: f7e89dc8 edi: f7639ff0 ebp: 00010000 esp: f7e89dc8 Since the hardware must have 16-byte alignment, the following patch fixes this by open coding the alignment adjustment. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2008-01-10[NIU]: Support for Marvell PHYMirko Lindner
From: Mirko Lindner <mlindner@marvell.com> This patch makes necessary changes in the Neptune driver to support the new Marvell PHY. It also adds support for the LED blinking on Neptune cards with Marvell PHY. All registers are using defines in the niu.h header file as is already done for the BCM8704 registers. [ Coding style, etc. cleanups -DaveM ] Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-09[SCSI] qla1280: fix 32 bit segment codeFUJITA Tomonori
There's an error remaining in the 32 bit descriptor code after the conversion to dma accessors: req_cnt is left uninitialised. qla1280_32bit_start_scsi gives the following warnings: drivers/scsi/qla1280.c: In function 'qla1280_32bit_start_scsi': drivers/scsi/qla1280.c:3044: warning: unused variable 'dma_handle' drivers/scsi/qla1280.c: In function 'qla1280_queuecommand': drivers/scsi/qla1280.c:3060: warning: 'req_cnt' is used uninitialized in this function drivers/scsi/qla1280.c:3042: note: 'req_cnt' was declared here Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-01-08[CONNECTOR]: Don't touch queue dev after decrement of ref count.Li Zefan
cn_queue_free_callback() will touch 'dev'(i.e. cbq->pdev), so it should be called before atomic_dec(&dev->refcnt). Signed-off-by: Li Zefan <lizf@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-08[FORCEDETH]: Fix reversing the MAC address on suspend.Björn Steinbrink
For cards that initially have the MAC address stored in reverse order, the forcedeth driver uses a flag to signal whether the address was already corrected, so that it is not reversed again on a subsequent probe. Unfortunately this flag, which is stored in a register of the card, seems to get lost during suspend, resulting in the MAC address being reversed again. To fix that, the MAC address needs to be written back in reversed order before we suspend and the flag needs to be reset. The flag is still required because at least kexec will never write back the reversed address and thus needs to know what state the card is in. Signed-off-by: Björn Steinbrink <B.Steinbrink@gmx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-08[NET]: mcs7830 passes msecs instead of jiffies to usb_control_msgRuss Dill
usb_control_msg was changed long ago (2.6.12-pre) to take milliseconds instead of jiffies. Oddly, mcs7830 wasn't added until 2.6.19-rc3. Signed-off-by: Russ Dill <Russ.Dill@asu.edu> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-08[NET]: kaweth was forgotten in msec switchover of usb_start_wait_urbRuss Dill
Back in 2.6.12-pre, usb_start_wait_urb was switched over to take milliseconds instead of jiffies. kaweth.c was never updated to match. Signed-off-by: Russ Dill <Russ.Dill@asu.edu> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-08[NET]: Make ->poll() breakout consistent in Intel ethernet drivers.David S. Miller
This makes the ->poll() routines of the E100, E1000, E1000E, IXGB, and IXGBE drivers complete ->poll() consistently. Now they will all break out when the amount of RX work done is less than 'budget'. At a later time, we may want put back code to include the TX work as well (as at least one other NAPI driver does, but by in large NAPI drivers do not do this). But if so, it should be done consistently across the board to all of these drivers. Signed-off-by: David S. Miller <davem@davemloft.net> Acked-by: Auke Kok <auke-jan.h.kok@intel.com>
2008-01-08[NET]: Fix drivers to handle napi_disable() disabling interrupts.David S. Miller
When we add the generic napi_disable_pending() breakout logic to net_rx_action() it means that napi_disable() can cause NAPI poll interrupt events to be disabled. And this is exactly what we want. If a napi_disable() is pending, and we are looping in the ->poll(), we want ->poll() event interrupts to stay disabled and we want to complete the NAPI poll ASAP. When ->poll() break out during device down was being handled on a per-driver basis, often these drivers would turn interrupts back on when '!netif_running()' was detected. And this would just cause a reschedule of the NAPI ->poll() in the interrupt handler before the napi_disable() could get in there and grab the NAPI_STATE_SCHED bit. The vast majority of drivers don't care if napi_disable() might have the side effect of disabling NAPI ->poll() event interrupts. In all such cases, when a napi_disable() is performed, the driver just disabled interrupts or is about to. However there were three exceptions to this in PCNET32, R8169, and SKY2. To fix those cases, at the subsequent napi_enable() points, I added code to ensure that the ->poll() interrupt events are enabled in the hardware. Signed-off-by: David S. Miller <davem@davemloft.net> Acked-by: Don Fry <pcnet32@verizon.net>
2008-01-08[NETXEN]: Fix ->poll() done logic.David S. Miller
If work_done >= budget we should always elide the NAPI completion. Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-08ssb: Fix probing of PCI cores if PCI and PCIE core is availableMichael Buesch
This will make sure that always the correct core is selected, even if there are both a PCI and PCI-E core on a PCI or PCI-E card. Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-08[NET]: Do not check netif_running() and carrier state in ->poll()David S. Miller
Drivers do this to try to break out of the ->poll()'ing loop when the device is being brought administratively down. Now that we have a napi_disable() "pending" state we are going to solve that problem generically. Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-08b43: Fix rxheader channel parsingMichael Buesch
This patch fixes the parsing of the RX data header channel field. The current code parses the header incorrectly and passes a wrong channel number and frequency for each frame to mac80211. The FIXMEs added by this patch don't matter for now as the code where they live won't get executed anyway. They will be fixed later. Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-08[ATM]: [nicstar] delay irq setup until card is configuredChas Williams
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-08[TULIP]: NAPI full quantum bug.Stephen Hemminger
This should fix the kernel warn/oops reported while routing. The tulip driver has a fencepost bug with new NAPI in 2.6.24 It has an off by one bug if a full quantum is reached. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-08[METH]: Fix MAC address handling.Thomas Bogendoerfer
meth didn't set a valid mac address during probing, but later during open. Newer kernel refuse to open device with 00:00:00:00:00:00 as mac address -> dead ethernet. This patch sets the mac address in the probe function and uses only the mac address from the netdevice struct when setting up the hardware. Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-08[NET]: Fix netx-eth.c compilation.Adrian Bunk
This was missed when commit e2ac455a18806b31c2d0da0a51d8740af5010b7a fixed the compile errors in drivers/net/netx-eth.c caused by commit 09f75cd7bf13720738e6a196cc0107ce9a5bd5a0. Signed-off-by: Adrian Bunk <adrian.bunk@movial.fi> Signed-off-by: David S. Miller <davem@davemloft.net>