Age | Commit message (Collapse) | Author |
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (21 commits)
libata: bump transfer chunk size if it's odd
libata: Return proper ATA INT status in pata_bf54x driver
pata_ali: trim trailing whitespace (fix checkpatch complaints)
pata_isapnp: Polled devices
pata_hpt37x: Fix cable detect bug spotted by Sergei
pata_ali: Lots of problems still showing up with small ATAPI DMA
pata_ali: Add Mitac 8317 and derivatives
libata-core: List more documentation sources for reference
ata_piix: Invalid use of writel/readl with iomap
sata_sil24: fix sg table sizing
pata_jmicron: fix disabled port handling in jmicron_pre_reset()
pata_sil680: kill bogus reset code (take 2)
ata_piix: port enable for the first SATA controller of ICH8 is 0xf not 0x3
ata_piix: only enable the first port on apple macbook pro
ata_piix: reorganize controller IDs
pata_sis.c: Add Packard Bell EasyNote K5305 to laptops
libata-scsi: be tolerant of 12-byte ATAPI commands in 16-byte CDBs
libata: use ATA_HORKAGE_STUCK_ERR for ATAPI tape drives
libata: workaround DRQ=1 ERR=1 for ATAPI tape drives
libata: remove unused functions
...
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
virtio: fix net driver loop case where we fail to restart
module: fix and elaborate comments
virtio: fix module/device unloading
lguest: Fix uninitialized members in example launcher
|
|
Amiga zorro bus: Add missing zorro_device_remove(). Without this ifconfig and
/proc/net/dev oops after unloading a Zorro network device driver module.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (39 commits)
ACPI: EC: Workaround for optimized controllers (version 3)
ACPI: EC: use printk_ratelimit(), add some DEBUG mode messages
Revert "ACPI: EC: Workaround for optimized controllers"
ACPI: fix two IRQ8 issues in IOAPIC mode
ACPI: Add missing spaces to printk format
cpuidle: fix HP nx6125 regression
cpuidle: add sched_clock_idle_[sleep|wakeup]_event() hooks
cpuidle: fix C3 for no bus-master control case
ACPI: thinkpad-acpi: fix oops when a module parameter has no value
Revert "Fix very high interrupt rate for IRQ8 (rtc) unless pnpacpi=off"
ACPI: EC: Don't init EC early if it has no _INI
Revert "acpi: make ACPI_PROCFS default to y"
Revert "ACPI: add documentation for deprecated /proc/acpi/battery in ACPI_PROCFS"
ACPI: Split out control for /proc/acpi entries from battery, ac, and sbs.
ACPI: Video: Increase buffer size for writes to brightness proc file.
ACPI: EC: Workaround for optimized controllers
ACPI: SBS: Fix retval warning
ACPI: Enable MSR (FixedHW) support for T-States
ACPI: Get throttling info from BIOS only after evaluating _PDC
ACPI: Use _TSS for throttling control, when present. Add error checks.
...
|
|
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] cio: Register/unregister subchannels only from kslowcrw.
[S390] Add missing die_notifier() call to die().
[S390] Fix memory detection.
[S390] Explicitly code allocpercpu calls in iucv
[S390] Dont overwrite lowcores on smp_send_stop().
[S390] Optimize storage key handling for anonymous pages
[S390] Fix kernel preemption.
[S390] appldata: remove unused binary sysctls.
[S390] cmm: remove unused binary sysctls.
[S390] Fix irq tracing and lockdep_sys_exit calls.
[S390] magic sysrq: check for in_atomic before doing an console_unblank
[S390] cio: change device sense procedure to work with pav aliases
|
|
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=9416
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
if you are lucky (unlucky?) enough to have shared interrupts, the
interrupt handler can be called before the tasklet and lock are ready
for use.
Signed-off-by: chas williams <chas@cmf.nrl.navy.mil>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
AMD Opteron processors before CG revision don't like C-states > 1.
This solves the long standing bugzilla #5303 and probably some more
on affected machines:
http://bugzilla.kernel.org/show_bug.cgi?id=5303
[ tglx@linutronix.de: reworked the patch so it does not wreck ia64 ]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
None of the drives I have follows what the standard says about
transfer chunk size. Of the four SATA and six PATA ATAPI devices
tested, four ignore transfer chunk size completely and the ones which
honor it don't behave according to the spec when it's odd.
According to the spec, transfer chunk size can be odd if the amount of
data to transfer equals or is smaller than the chunk size and the
device can indicate the same odd number and transfer the whole thing
at one go with a pad byte appended. However, in reality, none of the
drives I have does that. They all indicate and transfer even number
of bytes one byte shorter than the chunk size first; then indicate and
transfer two bytes, which is clearly out of spec.
In addition to unnecessary second PIO data phase, this also creates a
weird problem when combined with SATA controllers which perform PIO
via DMA. Some of these controllers use actualy number of bytes
received to update DMA pointer so chunks which are sized 4n + 2 makes
DMA pointer off by two bytes. This causes data corruption and buffer
overruns.
This patch rounds nbytes up to the nearest even number such that ATAPI
devices don't split data transfer for the last odd byte. This
shouldn't confuse controllers which depend on transfer chunk size as
devices will report the rounded-up number, actually transfer that much
and padding buffer is there to receive them.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
INT status can be OR.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
disabled
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
* Always pass the same value to free_irq() that we pass to
request_irq(). This fixes several bugs.
* Always call NCR5380_intr() with 'irq' and 'dev_id' arguments.
Note, scsi_falcon_intr() is the only case now where dev_id is not the
scsi_host.
* Always pass Scsi_Host to request_irq(). For most cases, the drivers
already did so, and I merely neated the source code line. In other
cases, either NULL or a non-sensical value was passed, verified to be
unused, then changed to be Scsi_Host in anticipation of the future.
In addition to the bugs fixes, this change makes the interface usage
consistent, which in turn enables the possibility of directly
referencing Scsi_Host from all NCR5380_intr() invocations.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
While adding sg chaining support to iSER, a "for" loop was replaced
with a "for_each_sg" loop. The "for" loop included the incrementation
of 2 variables. Only one of them is incremented in the current
"for_each_sg" loop. This caused iSER to think that all data is
unaligned, and all data was copied to aligned buffers.
This patch increments the missing counter inside the "for_each_sg"
loop whenever necessary.
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Wrong choice of port number caused modify_qp() to fail -- fixed.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
https://blackfin.uclinux.org/gf/project/uclinux-dist/forum/?action=ForumBrowse&forum_id=39&thread_id=23114&_forum_action=ForumMessageBrowse
Today I was dealing with the same problem, on my custom bf537 board, and bfin_mac driver.
I found that the problem is in setting ip_summed flag of skbuff structure,
Signed-off-by: Vitja Makarov <vitja.makarov@gmail.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Accidently I reversed the order of pci_save_state and
pci_set_power_state in .suspend()/.resume() callbacks
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
smc911x_set_multicast_list fails to fill out the multicast hash table
correctly; Bit 1 was used rather than bit 5 to decide if the lower or
upper register should be used.
The function is at the same time cleaned up by calling ether_crc rather
than using it's own bit reversal table.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The Marvell Yukon XL chipset appears to have a hardware glitch
where it will repeat the checksum of the last packet. Of course, this is
timing sensitive and only happens sometimes...
More info: http://bugzilla.kernel.org/show_bug.cgi?id=9381
As a workaround just disable hardware checksumming by default on
this chip version. The earlier workaround for PCIX, dual port
was also on Yukon XL so don't need to disable checksumming there.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Prevent driver from brawly logging packet checksum errors.
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Using own tx_packets counter instead of firmware counters.
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The smc911x_local pointer in smc911x_rcv is only used in the SMC_USE_DMA
case. Move it under the #ifdef so GCC doesn't generate a warning in the
non-DMA case.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
elif defined(CONFIG_*) should be used instead of elif CONFIG_*
so GCC doesn't give warnings about undefined symbols when the config
option is disabled.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The amd8111e network driver was broken by
bea3348eef27e6044b6161fd04c3152215f96411, which makes the driver
call napi_enable() and napi_disable() even if the driver had been
configured without CONFIG_AMD8111E_NAPI, and thus
netif_napi_add() had not been called on initialization.
This triggers a BUG in napi_enable().
This patch fixes the problem. Please apply.
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
A printk in the error handling code of dm9601.c was missing a newline.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Fix a long boot delay in the forcedeth driver. During initialization, the
timeout for the handshake between mgmt unit and driver can be very long.
The patch reduces the timeout by eliminating a extra loop around the
timeout logic.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=9308
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Cc: Alex Howells <astinus@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This patch adds new device ids and features for mcp79 devices into the
forcedeth driver.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
It's a bad idea to call flush_scheduled_work from within a
netdev->stop because the linkwatch will occasionally take the
rtnl lock from a workqueue context, and thus that can deadlock.
This reworks things a bit in that area to avoid the problem.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
If a card has no IRQ then pass no interrupt handler but allow polled
usage.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Hopefully there is a better long term solution but for now lets favour
reliability.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
And next time I'll be able to find the ata tape spec easily...
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Should use ioread* as discussed previously
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
sil24 unnecessarily used LIBATA_MAX_PRD and ATAPI sg table was short
by one entry which might cause very obscure problems. This patch
updates sg table sizing such that
* One full page is used for PRB + sg table. On 4k page,
this results in 253 sg's.
* Make ATAPI sg block properly sized.
* Make build fail if command block size doesn't equal PAGE_SIZE.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
There are two bugs in disabled port handling.
* test in PORT_PATA0 is reversed
* ->prereset should return -ENOENT for disabled ports not 0
The first bug makes the PATA channel considered disabled but the
second bug saves the day by returning 0. The net result is that cable
is always left at ATA_CBL_UNKNOWN. This results in false 80c
configuration and thus transfer errors.
This patch fixes both bugs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Since writing to two reserved bits ain't much of a housekeeping, I think it's
time we get rid of the custom error handler in this driver. ;-)
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Currently, gpio_keys.c assumes the GPIOs to be already properly configured;
this patch changes gpio-keys to perform explicit calls to gpio_request() and
gpio_configure_input().
This matches the behaviour of leds-gpio.
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
When booting under Microsoft Virtual Machine, the noloop quirk is
needed, otherwise PS/2 mouse is not properly detected.
Reported-by: Lawrence Steeger <vendor@russte.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
We know exactly what IRQ we are using, so synchronize_irq()
suits much better. Plus synchronize_sched() will not work
for us in -rt kernels.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Mattia Dongili <malattia@linux.it>
|
|
Properly set up parent on input devices registered by sonypi.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Mattia Dongili <malattia@linux.it>
|
|
Properly set up parent on input devices registered by sony-laptop.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Mattia Dongili <malattia@linux.it>
|
|
Move the code which marks the minor number as free to mmc_blk_put() so
that it happens on the final close() (or removal), instead of doing it
at removal even when the device is still logically open.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
It is possible to handle arbitrary block sizes with tifm card reader by
conditionally switching to PIO in case such block has to be delivered. At
the beginning of each request, DMA is either disabled (non-power-of-2 block
size) or set to load time user preference.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Some cards have been reported to signal that they're ready prematurely.
Checking both the busy bit and card state solves the issue.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
The APM emulation is currently broken as a result of commit
831441862956fffa17b9801db37e6ea1650b0f69
"Freezer: make kernel threads nonfreezable by default"
that removed the PF_NOFREEZE annotations from apm_ioctl() without adding
the appropriate freezer hooks. Fix it and remove the unnecessary variable flags
from apm_ioctl().
Special thanks to Franck Bui-Huu <vagabon.xyz@gmail.com> for pointing out the
problem.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Franck Bui-Huu <vagabon.xyz@gmail.com>
Cc: Nigel Cunningham <nigel@nigel.suspend2.net>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Conflicts:
drivers/acpi/ec.c
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Some controllers fail to send confirmation GPE after address or data write.
Detect this and don't expect such confirmation in future.
This is a generalization of previous workaround
(66c5f4e7367b0085652931b2f3366de29e7ff5ec), which did only read address.
Reference: http://bugzilla.kernel.org/show_bug.cgi?id=9327
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Tested-by: Romano Giannetti <romano.giannetti@gmail.com>
Tested-by: Mats Johannesson
Signed-off-by: Len Brown <len.brown@intel.com>
|