| Age | Commit message (Collapse) | Author |
|---|
|
Several tests in the ipv6 routing code check IFF_LOOPBACK, and
allowing stacking such as VLAN'ing on top of loopback results in a
netdevice which reports IFF_LOOPBACK but really isn't the loopback
device.
Instead of spamming the ipv6 routing code with even more special tests,
simply disallow VLAN over loopback.
The result of this patch is:
# modprobe 8021q
# vconfig add lo 43
ERROR: trying to add VLAN #43 to IF -:lo:- error: Operation not supported
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes port identification on optic devices when there's no link on the port.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The memory leak was caused by unintentional assignment of the Rx path
destroy callback function pointer to NULL just after correct
initialization.
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During a kernel crash, bna control path state machine and firmware do not
get a notification and hence are not cleanly shutdown. The registers
holding driver/IOC state information are not reset back to valid
disabled/parking values. This causes subsequent driver initialization
to hang during kdump kernel boot. This patch, during the initialization
of first PCI function, resets corresponding register when unclean shutown
is detect by reading chip registers. This will make sure that ioc/fw
gets clean re-initialization.
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
priv->tx_power_next is not initialized to max supported power,
but instead default value is used, what cause errors like
[ 58.597834] iwl3945 0000:03:00.0: Requested user TXPOWER 15 above upper limit 14.
[ 58.597839] iwl3945 0000:03:00.0: Error setting Tx power (-22).
if maximum tx power read from the eeprom is smaller than default.
In consequence card is unable to initialize properly. Fix the problem
and cleanup tx power initialization.
Reported-and-tested-by: Robin Dong <hao.bigrat@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Machines are getting deadlock in four node cluster environment.
All nodes are accessing (find /gfs2 -depth -print|cpio -ocv > /dev/null)
200 GB storage on a GFS2 filesystem.
This result in memory fragmentation and driver receives 18 frags for
1448 byte packets.
For non tso packet, fw drops the tx request, if it has >14 frags.
Fixing it by pulling extra frags.
Cc: stable@kernel.org
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 74888760d40b3ac9054f9c5fa07b566c0676ba2d
"dt/net: Eliminate users of of_platform_{,un}register_driver"
broke building mscan driver. Fix it.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bwh/sfc-2.6
|
|
Enabling write-combining may also enable read reordering. The BIU is
only guaranteed to read from a 128-bit CSR or 64-bit SRAM word when
the host reads from its lowest address; otherwise the BIU may use the
latched value. Therefore we need to reinstate the read memory
barriers after the first read operation for each CSR or SRAM word.
Signed-off-by; Ben Hutchings <bhutchings@solarflare.com>
|
|
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a skb is delivered to a registered callback, cn_call_callback()
incorrectly returns -ENODEV after freeing the skb, causing cn_rx_skb()
to free the skb a second time.
Reported-by: Eric B Munson <emunson@mgebm.net>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Tested-by: Eric B Munson <emunson@mgebm.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pass the correct module name and device interface so that
ethtool can display the proper values.
The firmware version will be fixed later on when the FW
can actually report a version. :)
Reported-by: Richard Farina <sidhayn@gmail.com>
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Tested-by: Richard Farina <sidhayn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
During PHY errors, the MAC can sometimes fail to enter an idle state on older
hardware (before AR9380) after an rx stop has been requested.
This typically shows up in the kernel log with messages like these:
ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
------------[ cut here ]------------
WARNING: at drivers/net/wireless/ath/ath9k/recv.c:504 ath_stoprecv+0xcc/0xf0 [ath9k]()
Call Trace:
[<8023f0e8>] dump_stack+0x8/0x34
[<80075050>] warn_slowpath_common+0x78/0xa4
[<80075094>] warn_slowpath_null+0x18/0x24
[<80d66d60>] ath_stoprecv+0xcc/0xf0 [ath9k]
[<80d642cc>] ath_set_channel+0xbc/0x270 [ath9k]
[<80d65254>] ath_radio_disable+0x4a4/0x7fc [ath9k]
When this happens, the state that the MAC enters is easy to identify and
does not result in bogus DMA traffic, however to ensure a working state
after a channel change, the hardware should still be reset.
This patch adds detection for this specific MAC state, after which the above
warnings completely disappear in my tests.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Cc: Kyungwan Nam <Kyungwan.Nam@Atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
During self-tests we use efx_process_channel_now() to handle
completion and other events synchronously. This disables interrupts
and NAPI processing for the channel in question, but it may still be
interrupted by another channel. A single socket may receive packets
from multiple net devices or even multiple channels of the same net
device, so this can result in deadlock on a socket lock.
Receiving packets in process context will also result in incorrect
classification by the network cgroup classifier.
Therefore, we must only use efx_process_channel_now() in the offline
loopback tests (which never deliver packets up the stack) and not for
the online interrupt and event tests.
For the interrupt test, there is no reason to process events. We
only care that an interrupt is raised.
For the event test, we want to know whether events have been received,
and there may be many events ahead of the one we inject. Therefore
remove efx_channel::magic_count and instead test whether
efx_channel::eventq_read_ptr advances. This is currently an event
queue index and might wrap around to exactly the same value, resulting
in a false negative. Therefore move the masking to efx_event() and
efx_nic_eventq_read_ack() so that it cannot wrap within the time of
the test.
The event test also tries to diagnose failures by checking whether an
event was delivered without causing an interrupt. Add and use a
helper function that only does this.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
If the TX queues are running during loopback self tests, host
traffic gets looped back which causes the test to fail. Avoid
restarting the TX queues after the port reset so that any packets
sent by the host get held back until after the tests have completed.
[bwh: Also wake all TX queues at the end of self-tests.]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Machines are getting deadlock in four node cluster environment.
All nodes are accessing (find /gfs2 -depth -print|cpio -ocv > /dev/null)
200 GB storage on a GFS2 filesystem.
This result in memory fragmentation and driver receives 18 frags for
1448 byte packets.
For non tso packet, fw drops the tx request, if it has >14 frags.
Fixing it by pulling extra frags.
Cc: stable@kernel.org
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
replace relpy with reply.
replace premanent with permanent.
Signed-off-by: Weiping Pan(潘卫平) <panweiping3@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
replace tranmitted with transmitted.
replace tranmitting with transmitting.
Signed-off-by: Weiping Pan(潘卫平) <panweiping3@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now, alb_bond_info uses rx_ntt,rlb_update_delay_counter and
rlb_update_retry_counter to decide when to call rlb_update_rx_clients().
Signed-off-by: Weiping Pan(潘卫平) <panweiping3@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now bonding-alb uses delayed_work instead of timer_list.
Signed-off-by: Weiping Pan(潘卫平) <panweiping3@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is unnecessary to set save_load to 1 here,
as the tx_hashtbl is just kzalloced.
Signed-off-by: Weiping Pan(潘卫平) <panweiping3@gmail.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On some old MAC chips without COE sometime the
Transmit Underflow error is issued.
The driver aborted all the transmission process
and initialized it from scratch.
This breaks the network activity as raised by Nachiketa
on a SPEAr board.
The patch is to fix this rare underflow event.
The driver will only clear the interrupt and the Tx
DMA will go out the Suspend state as soon as the
descriptor is fetched again.
The driver will continue to bump-up the DMA FIFO threshold
that, indeed, helped somebody to prevent this kind of error
in the past as well.
Reported-by: Nachiketa Prachanda <nprachanda@ncomputing.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch reviews the open function and fixes some
errors when exit with an error state.
It also moves the request_irq after core is initialized
when interrupts are properly masked.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Hacked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a compilation error when build the
dwmac_lib with the DEBUG option enabled.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
Otherwise, IWLWIFI_LEGACY has to be selected independently before the
drivers are made available.
Reported-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
In commit 13583b16592a ("PCI: refactor io size calculation code") Ram
had a thinko in the refactorization of the code: the end result used the
variable 'align' for the bus alignment, but the original code used
'min_align'.
Since then, another use of that 'align' variable got introduced by
commit c8adf9a3e873 ("PCI: pre-allocate additional resources to devices
only after successful allocation of essential resources.")
Fix both of those uses to use 'min_align' as they should.
Daniel Hellstrom <daniel@gaisler.com>
Acked-by: Ram Pai <linuxram@us.ibm.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (34 commits)
net: Add support for SMSC LAN9530, LAN9730 and LAN89530
mlx4_en: Restoring RX buffer pointer in case of failure
mlx4: Sensing link type at device initialization
ipv4: Fix "Set rt->rt_iif more sanely on output routes."
MAINTAINERS: add entry for Xen network backend
be2net: Fix suspend/resume operation
be2net: Rename some struct members for clarity
pppoe: drop PPPOX_ZOMBIEs in pppoe_flush_dev
dsa/mv88e6131: add support for mv88e6085 switch
ipv6: Enable RFS sk_rxhash tracking for ipv6 sockets (v2)
be2net: Fix a potential crash during shutdown.
bna: Fix for handling firmware heartbeat failure
can: mcp251x: Allow pass IRQ flags through platform data.
smsc911x: fix mac_lock acquision before calling smsc911x_mac_read
iwlwifi: accept EEPROM version 0x423 for iwl6000
rt2x00: fix cancelling uninitialized work
rtlwifi: Fix some warnings/bugs
p54usb: IDs for two new devices
wl12xx: fix potential buffer overflow in testmode nvs push
zd1211rw: reset rx idle timer from tasklet
...
|
|
This patch adds support for SMSC's LAN9530, LAN9730 and LAN89530 USB
ethernet controllers to the existing smsc95xx driver by adding
their new USB VID/PID pairs.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* git://git.infradead.org/mtd-2.6:
mtd: atmel_nand: use CPU I/O when buffer is in vmalloc(ed) region
mtd: atmel_nand: modify test case for using DMA operations
mtd: atmel_nand: fix support for CPUs that do not support DMA access
mtd: atmel_nand: trivial: change DMA usage information trace
mtd: mtdswap: fix printk format warning
|
|
This patch fixes a very serious off-by-one bug in
the driver, which could leave the device in an
unresponsive state.
The problem was that the extra_len variable [used to
reserve extra scratch buffer space for the firmware]
was left uninitialized. Because p54_assign_address
later needs the value to reserve additional space,
the resulting frame could be to big for the small
device's memory window and everything would
immediately come to a grinding halt.
Reference: https://bugs.launchpad.net/bugs/722185
Cc: <stable@kernel.org>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Jason Conti <jason.conti@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
These missing chip wakeups mainly cause crashes on AR5416 cards in MIPS
boards, but have also been reported to cause radio stability issues on
AR9285.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] compile fix for latest binutils
[S390] cio: prevent purging of CCW devices in the online state
[S390] qdio: fix init sequence
[S390] Fix parameter passing for smp_switch_to_cpu()
[S390] oprofile s390: prevent stack corruption
|
|
If not done, second attempt to open the RX ring would cause memory corruption.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When bringing the port up, performing a SENSE_PORT command
To try and check to which physical link type (IB or Ethernet) the physical
port is connected.
In case there is no valid link partner, the port will come up as its
supported default.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
watchdog: mpc8xxx_wdt: fix build
|
|
Since 1c48a5c93da6313 (dt: Eliminate of_platform_{,un}register_driver)
mpc8xxx_wdt no longer builds as it tries to refer to a 'match' variable
rather than ofdev->dev.of_match that it checks just before.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-2.6
* 'fbdev-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-2.6:
efifb: Add override for 11" Macbook Air 3,1
efifb: Support overriding fields FW tells us with the DMI data.
fb: Reduce priority of resource conflict message
savagefb: Remove obsolete else clause in savage_setup_i2c_bus
savagefb: Set up I2C based on chip family instead of card id
savagefb: Replace magic register address with define
drivers/video/bfin-lq035q1-fb.c: introduce missing kfree
video: s3c-fb: fix checkpatch errors and warning
efifb: support AMD Radeon HD 6490
s3fb: fix Virge/GX2
fbcon: Remove unused 'display *p' variable from fb_flashcursor()
fbdev: sh_mobile_lcdcfb: fix module lock acquisition
fbdev: sh_mobile_lcdcfb: add blanking support
viafb: initialize margins correct
viafb: refresh rate bug collection
sh: mach-ap325rxa: move backlight control code
sh: mach-ecovec24: support for main lcd backlight
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6
* 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: select ARCH_NO_SYSDEV_OPS.
sh: fix build error in board-sh7757lcr.c
sh: landisk: Remove whitespace
sh: landisk: Remove mv_nr_irqs
sh: sh-sci: Fix double initialization by serial_console_setup
serial: sh-sci: prevent setup of uninitialized serial console
dma: shdma: add checking the DMAOR_AE in sh_dmae_err
|
|
'timers-fixes-for-linus', 'irq-fixes-for-linus' and 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86-32, fpu: Fix FPU exception handling on non-SSE systems
x86, hibernate: Initialize mmu_cr4_features during boot
x86-32, NUMA: Fix ACPI NUMA init broken by recent x86-64 change
x86: visws: Fixup irq overhaul fallout
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Clean up rebalance_domains() load-balance interval calculation
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/mrst/vrtc: Fix boot crash in mrst_rtc_init()
rtc, x86/mrst/vrtc: Fix boot crash in rtc_read_alarm()
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
genirq: Fix cpumask leak in __setup_irq()
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf probe: Fix listing incorrect line number with inline function
perf probe: Fix to find recursively inlined function
perf probe: Fix multiple --vars options behavior
perf probe: Fix to remove redundant close
perf probe: Fix to ensure function declared file
|
|
Joe Culler reported a problem with his AR9170 device:
> ath: EEPROM regdomain: 0x5c
> ath: EEPROM indicates we should expect a direct regpair map
> ath: invalid regulatory domain/country code 0x5c
> ath: Invalid EEPROM contents
It turned out that the regdomain 'APL7_FCCA' was not mapped yet.
According to Luis R. Rodriguez [Atheros' engineer] APL7 maps to
FCC_CTL and FCCA maps to FCC_CTL as well, so the attached patch
should be correct.
Cc: <stable@kernel.org>
Reported-by: Joe Culler <joe.culler@gmail.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When the mwl8k driver attempts and fails to switch from sta to ap
firmware (or vice-versa) in the mwl8k_add_interface routine, the
mwl8k_stop routine will be called. This routine must not attempt
to free the irq if it was not requested.
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
At least EEPROM version 0x11A has the wrong
number of chains programmed into it for some
reason, so we need to override in the driver.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6
* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6: (28 commits)
staging: usbip: bugfix for isochronous packets and optimization
staging: usbip: bugfix add number of packets for isochronous frames
staging: usbip: bugfixes related to kthread conversion
staging: usbip: fix shutdown problems.
staging: hv: Fix GARP not sent after Quick Migration
staging: IIO: IMU: ADIS16400: Avoid using printk facility directly
staging: IIO: IMU: ADIS16400: Fix product ID check, skip embedded revision number
staging: IIO: IMU: ADIS16400: Make sure only enabled scan_elements are pushed into the ring
staging: IIO: IMU: ADIS16400: Fix addresses of GYRO and ACCEL calibration offset
staging: IIO: IMU: ADIS16400: Add delay after self test
staging: IIO: IMU: ADIS16400: Fix up SPI messages cs_change behavior
staging/rtl81*: build as loadable modules only
staging: brcm80211: removed 'is_amsdu causing toss' log spam
staging: brcm80211: fix for 'Short CCK' log spam
staging: brcm80211: fix for 'AC_BE txop..' logs spammed problem
staging: memrar: remove driver from tree
staging: sep: remove last memrar remnants
staging: fix hv_mouse build, needs delay.h
staging: fix olpc_dcon build errors
staging: sm7xx: fixed defines
...
Fix up trivial conflict in drivers/staging/memrar/memrar_handler.c
(deleted vs trivial spelling fixes)
|
|
* 'for-linus' of git://git.infradead.org/ubifs-2.6:
UBI: do not select KALLSYMS_ALL
UBI: do not compare array with NULL
UBI: check if we are in RO mode in the erase routine
UBIFS: fix debugging failure in dbg_check_space_info
UBIFS: fix error path in dbg_debugfs_init_fs
UBIFS: unify error path dbg_debugfs_init_fs
UBIFS: do not select KALLSYMS_ALL
UBIFS: fix assertion warnings
UBIFS: fix oops on error path in read_pnode
UBIFS: do not read flash unnecessarily
|
|
* 'for-linus2' of git://git.profusion.mobi/users/lucas/linux-2.6:
Fix common misspellings
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: Add support for CH Pro Throttle
HID: hid-magicmouse: Increase evdev buffer size
HID: add FF support for Logitech G25/G27
HID: roccat: Add support for wireless variant of Pyra
HID: Fix typo Keyoutch -> Keytouch
HID: add support for Skycable 0x3f07 wireless presenter
|
|
Fix build failure issue for hv_mouse
When build 2.6.39-rc1 kernel, it will be blocked at build hv_mouse.
drivers/staging/hv/hv_mouse.c: In function ‘ReleaseInputDevice’:
drivers/staging/hv/hv_mouse.c:293: error: implicit declaration of function ‘udelay’
Signed-off-by: Youquan Song <youquan.song@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
