| Age | Commit message (Collapse) | Author |
|---|
|
commit 8ac4ce742c66100931b6f2d7a36b0df08bc721fe ("ide: fix host drivers
depending on ide_generic to probe for interfaces (take 2)") moved probing
to falconide but forgot to take care of Atari specific locking - fix it.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Signed-off-by: Mikko Rapeli <mikko.rapeli@teleca.com>
Tested-by: Bart Champagne <bart@as35701.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
commit 29dd59755a849cc6475faa6a75f3b804e23a6fc2 ("ide: remove ide_setup_ports")
forgot to take into account the base addresses for the CONTROL registers for
falconide and macide, as pointed out by Michael Schmitz.
Falconide was tested on Aranym.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/nes: Fix possible array overrun
RDMA/nes: Fix VLAN support
RDMA/nes: Fix MAC interrupt erroneously masked on ifdown
IB: Fix return value in ib_device_register_sysfs()
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (59 commits)
V4L/DVB (7219): zoran: Fix namespace conflicts with Zoran 'GPIO_MAX' enum
V4L/DVB (7205): tuner-xc2028 depends on FW_LOADER
V4L/DVB (7201): cx88-mpeg: Fix race condition in variable access
V4L/DVB (7200): Fix FM firmware loading
V4L/DVB (7198): V4L, include ioctl.h in videodev headers
V4L/DVB (7197): bttv: Fix overlay divide error
V4L/DVB (7195): xc5000: fix build error when built as module
V4L/DVB (7194): cx88-mpeg: Allow concurrent access to cx88-mpeg devices
V4L/DVB (7193): tveeprom: Add proper tuner mapping for hauppauge eeprom id 133
V4L/DVB (7192): Adds support for Genius TVGo A11MCE
V4L/DVB (7189): autosuspend support
V4L/DVB (7188): radio-si470x version 1.0.6
V4L/DVB (7186): tda10086: make the 22kHz tone for DISEQC a config option
V4L/DVB (7183): radio-si470x: fix build warning
V4L/DVB (7180): em28xx: add URB_NO_TRANSFER_DMA_MAP, since urb->transfer_dma is set
V4L/DVB (7179): Allow more than one em28xx board
V4L/DVB (7164): em28xx-alsa: Add a missing mutex
V4L/DVB (7163): em28xx: makes audio settings more stable
V4L/DVB (7162): em28xx: Fix endian and returns the correct values
V4L/DVB (7161): em28xx: Fix printing debug values higher than 127
...
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
[CRYPTO] null: Add missing Kconfig dependency on BLKCIPHER
[CRYPTO] tcrypt: Add missing Kconfig dependency on BLKCIPHER
[HIFN]: Fix invalid config ifdefs for RNG support
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In nes_create_qp(), the test
if (nesqp->mmap_sq_db_index > NES_MAX_USER_WQ_REGIONS) {
is used to error out if the db_index is too large; however, if the
test doesn't trigger, then the index is used as
nes_ucontext->mmap_nesqp[nesqp->mmap_sq_db_index] = nesqp;
and mmap_nesqp is declared as
struct nes_qp *mmap_nesqp[NES_MAX_USER_WQ_REGIONS];
which leads to an array overrun if the index is exactly equal to
NES_MAX_USER_WQ_REGIONS. Fix this by bailing out if the index is
greater than or equal to NES_MAX_USER_WQ_REGIONS.
This was spotted by the Coverity checker (CID 2162).
Acked-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Hp is providing a Hardware WatchDog Timer driver that will only work with the
specific HW Timer located in the HP ProLiant iLO 2 ASIC. The iLO 2 HW Timer
will generate a Non-maskable Interrupt (NMI) 9 seconds before physically
resetting the server, by removing power, so that the event can be logged to
the HP Integrated Management Log (IML), a Non-Volatile Random Access Memory
(NVRAM). The logging of the event is performed using the HP ProLiant ROM via
an Industry Standard access known as a BIOS Service Directory Entry.
Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
functions to __initdata
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
This patch converts the MTX-1 to be a platform device, use the available
generic GPIO API for the MTX-1 board and register the miscdev alias.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Support watchdog timers built into SiByte MIPS SoCs.
Signed-off-by: Andy Sharp <andy.sharp@onstor.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Thanks to Martin Michlmayr <tbm@cyrius.com> for reporting this issue:
The zoran driver fails to compile on the ARM Orion platform with:
In file included from drivers/media/video/zoran_procfs.c:50:
drivers/media/video/zoran.h:232: error: expected identifier before numeric
constant
The reason is that drivers/media/video/zoran.h defines an enum with
GPIO_MAX in it, but Orion contains a #define GPIO_MAX 32 in
include/asm-arm/arch-orion/orion.h
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
There was a possible race condition in the increment/decrement of
the active device references counter.
Thanks to Trent Piepho (xyzzy@speakeasy.org) for bringing it up.
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
There's no need to load SCode table for FM.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
The initial work to convert the bttv driver to V4L2 "Partial conversion
from V4L1 to V4L2" (e84619b17440ccca4e4db7583d126c4189b987e5), missed
the line which set the appropriate overlay crop structure in the newly
allocated bttv_buffer. This then causes a divide error in the
bttv_calc_geo function.
Signed-off-by: Robert Fitzsimons <robfitz@273k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
drivers/built-in.o: In function `set_type':
tuner-core.c:(.text+0x8879d): undefined reference to `xc5000_attach'
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
The spinlock is held over too large a region: pscratch is a permanent
address (it's allocated at boot time and never changes). All you need
the smp lock for is mediating the scratch in use flag, so fix this by
moving the spinlock into the case where we set the pscratch_busy flag
to false.
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
scsi/qla2xxx/qla_dfs.c: In function 'qla2x00_dfs_fce_show':
scsi/qla2xxx/qla_dfs.c:26: warning: format '%llx' expects type 'long long unsigned int', but argument 3 has type 'uint64_t'
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
The panic occurs if we get a MSGIN or MSGOUT for an unidentified SCB
(meaning we didn't identify the outstanding command it was for). For
MSGIN this is wrong because it could be an unsolicited negotiation
MSGIN from the target.
Still panic on unsolicited MSGOUT because this would represent a
mistake in the negotiation phases. However, we should fix this as
well. The specs say we should go to bus free for unexpected msgin.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
scsi_debug does at several places:
for_each_sg(sdb->table.sgl, sg, sdb->table.nents, k) {
kaddr = (unsigned char *)
kmap_atomic(sg_page(sg), KM_USER0);
We cannot do something like that with the clustering enabled (or we
can use scsi_kmap_atomic_sg).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Apparently the fix to [SCSI] fas216: Use scsi_eh API for REQUEST_SENSE
invocation didn't show up in the final version sent to linus.
Correct this omission.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
From conversations with the maintainers the _p isn't needed so kill it.
That removes the last non ISA _p user from the SCSI layer to my knowledge.
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: "Yang, Bo" <Bo.Yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Verified all the arches necessary select the CONFIG_64BIT symbol. This
also kills the warning (since it was using the 32-bit case) on parisc64
and mips64.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This driver has been failing under heavy load with
aic94xx: escb_tasklet_complete: REQ_TASK_ABORT, reason=0x6
aic94xx: escb_tasklet_complete: Can't find task (tc=4) to abort!
The second message is because the driver fails to identify the task
it's being asked to abort. On closer inpection, there's a thinko in
the for each task loop over pending tasks in both the REQ_TASK_ABORT
and REQ_DEVICE_RESET cases where it doesn't look at the task on the
pending list but at the one on the ESCB (which is always NULL).
Fix by looking at the right task. Also add a print for the case where
the pending SCB doesn't have a task attached.
Not sure if this will fix all the problems, but it's a definite first
step.
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
one system: initrd get courrupted:
RAMDISK: Compressed image found at block 0
RAMDISK: incomplete write (-28 != 2048) 134217728
crc error
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 388k freed
init_special_inode: bogus i_mode (177777)
Warning: unable to open an initial console.
init_special_inode: bogus i_mode (177777)
init_special_inode: bogus i_mode (177777)
Kernel panic - not syncing: No init found. Try passing init= option to kernel.
bisected to
commit 9927c68864e9c39cc317b4f559309ba29e642168
Author: James Bottomley <James.Bottomley@HansenPartnership.com>
Date: Sun Feb 3 15:48:56 2008 -0600
[SCSI] ses: add new Enclosure ULD
changes:
1. change char to unsigned char to avoid type change later.
2. preserve len for page1
3. need to move desc_ptr even the entry is not enclosure_component_device/raid.
so keep desc_ptr on right position
4. record page7 len, and double check if desc_ptr out of boundary before touch.
5. fix typo in subenclosure checking: should use hdr_buf instead.
[jejb: style fixes]
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
It currently isn't possible to open the frontend device of cx88-mpeg devices
(DVB or Blackbird) multiple times concurrently. (for instance, to attach a
signal monitoring tool while reading a stream, or to send a frequency change
ioctl) This patch fixes that condition.
Signed-off-by: Roland Stoll <roland@xindex.de>
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Do away with the need to set tuner=63 on cx88xx with recent HVR-1300 boards
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Signed-off-by: Adrian Pardini <pardo.bsso@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Together with Oliver Neukum from Novell, USB autosuspend support was added.
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
This patch combines all the finished discussions and its resulting patches from
the mailing list.
The version 1.0.6 is mainly influenced by Oliver Neukum. He found a lot of
small issues, that are fixed with this patch now. For me the most interesting
thing is, that it's now safer to use it on other architectures.
The history for version 1.0.6 is:
- fixed coverity checker warnings in *_usb_driver_disconnect
- probe()/open() race by correct ordering in probe()
- DMA coherency rules by separate allocation of all buffers
- use of endianness macros
- abuse of spinlock, replaced by mutex
- racy handling of timer in disconnect, replaced by delayed_work
- racy interruptible_sleep_on(), replaced with wait_event_interruptible()
- handle signals in read()
The driver is tested with all Debian/testing radio programs and rdsd. The patch
is tested against checkpatch.pl v1.12.
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Some cards need the diseqc signal modulated, while some just need
the envelope to control the LNB supply.
This fixes Bug 9887
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
fix the following build warning:
radio-si470x.c: In function 'si470x_get_rds_registers':
radio-si470x.c:562: warning: format '%ld' expects type 'long int',
but argument 3 has type 'unsigned int'
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
is set
Thanks to Alan Stern <stern@rowland.harvard.edu> for pointing this issue.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
em28xx driver is capable of handling more than one usb device. However, isoc
transfers require a large amount of data to be transfered.
Before this patch, just one em28xx board were enough to allocate more than 50%
URBs:
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 8
B: Alloc=480/800 us (60%), #Int= 0, #Iso= 2
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
So, only one board could use an USB host at the same time. After the patch, it
is possible to use more than one em28xx at the same time, on the same usb host,
if the image size is slower or equal to 345600, since those images will
require about 30% of the URBs:
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 8
B: Alloc=232/800 us (29%), #Int= 0, #Iso= 2
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
So, in thesis, after the patch, it would be possible to use up to 3 boards by
each usb host, if the devices are generating small images.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Improves audio configurations on em28xx:
- mutes audio before changing amux;
- adds a delay after setting audio src;
- waits up to 50ms for ac97 busy.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Adds vidioc_[g|s]_register handlers. This allows getting/setting register
from em28xx.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
AC97 register initialization seem to always be needed. This patch fixes audio
for Prolink/Pixelview USB2 board.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
variable
drivers/media/video/em28xx/em28xx-core.c: In function 'em28xx_set_audio_source':
drivers/media/video/em28xx/em28xx-core.c:276: warning: 'no_ac97' may be used uninitialized in this function
This looks like a genuine bug to me.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
'!' has a higher priority than '&': bitanding has no effect.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Device description:
WinTV-HVR-900
M/R: 65018/B3C0 ##4207
Signed-off-by: Luc Saillard <luc@saillard.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
videobuf functions at close() method already locks videobuf. It makes no sense
to keep the locking at empress close() method.
There is also a lock at open() method. I'm not sure if it is safe to remove the
locking there.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
This helps to identify where vb_lock is being used, and find missusages of the
locks.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Removes the duplicated mutex_init code.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Improved display of still pictures (VIDEO_STILLPICTURE ioctl).
Ensure that both fields are displayed for progressive frames.
Thanks to Reinhard Nissl and Klaus Schmidinger for finding out
that the FREEZE command does this.
Thanks-to: Reinhard Nissl <rnissl@gmx.de>
Thanks-to: Klaus Schmidinger <Klaus.Schmidinger@cadsoft.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
