Age | Commit message (Collapse) | Author |
|
register.
Don't display the register when it's not appropriate for the specific port.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
VIDB/TS1 did not stream.
Certain DVB cards that have demodulators on TS1/VIDB were not streaming packets.
This ensure the pin directions on PAD_CTRL are set correctly, solving the issue.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
PAD_CTRL controls TS1 and TS2 input and output states, if the register
became corrupt the driver was never able to recover.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
/dev/video1
With the HVR1800, trying to use video0 and video1 simultaneously caused
buffer corruption in the PCIe bridge. This fix reallocates video1
buffer locations to avoid the issue.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
captures
cx18: Lock the aux PLL to the video pixel rate for analog captures. The
datasheet for the CX25840 says this is important for MPEG encoding applications.
To ensure the PLL locking was correct, also fixed the aux PLL's multiplier to
be computed based on a precise crystal freq of 4.5 MHz/286 * 455/2 * 8 =
28636363.6363... instead of the imporperly rounded 28636363.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
SIF input
cx18: Fix 32 kHz audio sample output rate for analog tuner SIF input so it
works. The AUX_PLL VCO was being operated at 196.6 MHz out of the spec'ed
200-600 MHz range. Fixed the multipler and post dividers to operate the VCO
within specification and added comments on how magic numbers are derived.
Thanks to Hans Verkuil for pointing out this interesting problem to solve.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
from the code
gspca_sonixb remove one more no longer needed special case from the code
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
special cases
gspca_sonixb remove some no longer needed sn9c103+ov7630 special cases
Signed-off-by: Andoni Zubimendi <andoni.zubimendi@gmail.com>
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
saturation ctrls
gspca_sonixb remove non working ovXXXX contrast, hue and saturation ctrls
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Andoni Zubimendi has been doing some testing with his sn9c103 cam with
ov7630 sensor, and with this patch the exposure setting and autoexposure now
work.
This patch also removes some special cases in the shared ov6650 / ov7630 code
which now are handled the same for both sensors and it adds a new special case
which stops us from changing the hsync / vsync polarity settings from their
default on the ov7630 (which we were doing as a side-effect of using the ov6650
exposure code for the ov7630).
Last this patch removes the superficial difference between the OV7630 and
OV7630_3 sensors.
Signed-off-by: Andoni Zubimendi <andoni.zubimendi@gmail.com>
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
This patch contains the following cleanups:
- mark smscore_module_init() as __init
- mark smscore_module_exit as __exit
- make the following needlessly global code static:
- smscoreapi.c: struct g_smscore_notifyees
- smscoreapi.c: struct g_smscore_devices
- smscoreapi.c: struct g_smscore_deviceslock
- smscoreapi.c: struct g_smscore_registry
- smscoreapi.c: struct g_smscore_registrylock
- smscoreapi.c: smscore_module_init()
- smscoreapi.c: smscore_module_exit()
- smsdvb.c: struct g_smsdvb_clients
- smsdvb.c: struct g_smsdvb_clientslock
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
drivers/char/nwflash.c: In function 'flash_read':
drivers/char/nwflash.c:129: error: 'p' undeclared (first use in this function)
drivers/char/nwflash.c:129: error: (Each undeclared identifier is reported only once
drivers/char/nwflash.c:129: error: for each function it appears in.)
drivers/char/nwflash.c:129: error: 'count' undeclared (first use in this function)
drivers/char/nwflash.c:136: warning: passing argument 4 of 'simple_read_from_buffer' discards qualifiers from pointer target type
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
* Replace previous instances of the cpumask_of_cpu_ptr* macros
with a the new (lvalue capable) generic cpumask_of_cpu().
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
The acpi idle waits calls local_irq_save and then uses mwait to go into
idle. The tracer gets reenabled at local_irq_save but does not detect that
the idle allows for wake ups.
This patch adds code to disable the tracing when acpi puts the CPU to idle.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
From: Heiko Carstens <heiko.carstens@de.ibm.com>
This makes qeth working again after git commit
e3c50d5d25ac09efd9acbe2b2a3e365466de84ed
"netdev: netdev_priv() can now be sane again.".
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Removes legacy reinvent-the-wheel type thing. The generic
machinery integrates much better to automated debugging aids
such as kerneloops.org (and others), and is unambiguous due to
better naming. Non-intuively BUG_TRAP() is actually equal to
WARN_ON() rather than BUG_ON().
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for populating an SPI bus based on data in the
OF device tree. This is useful for powerpc platforms which use the
device tree instead of discrete code for describing platform layout.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
spi_new_device() allocates and registers an spi device all in one swoop.
If the driver needs to add extra data to the spi_device before it is
registered, then this causes problems. This is needed for OF device
tree support so that the SPI device tree helper can add a pointer to
the device node after the device is allocated, but before the device
is registered. OF aware SPI devices can then retrieve data out of the
device node to populate a platform data structure.
This patch splits the allocation and registration portions of code out
of spi_new_device() and creates two new functions; spi_alloc_device()
and spi_register_device(). spi_new_device() is modified to use the new
functions for allocation and registration. None of the existing users
of spi_new_device() should be affected by this change.
Drivers using the new API can forego the use of spi_board_info
structure to describe the device layout and populate data into the
spi_device structure directly.
This change is in preparation for adding an OF device tree parser to
generate spi_devices based on data in the device tree.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
SPI has a similar problem as I2C in that it needs to determine an
appropriate modalias value for each device node. This patch adapts
the of_i2c of_find_i2c_driver() function to be usable by of_spi also.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Compile error on other architectures:
CC drivers/mfd/tc6393xb.o
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/mfd/tc6393xb.c: In function ‘tc6393xb_attach_irq’:
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/mfd/tc6393xb.c:324: error: implicit declaration of function ‘set_irq_flags’
...
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Heikki Orsila <heikki.orsila@iki.fi>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
|
|
* git://git.infradead.org/embedded-2.6:
Make console charset translation optional
|
|
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Use only statically allocated data for PHY config packet transmission.
With the previous incarnation, some data wouldn't be freed if the packet
transmit callback was never called.
A theoretical drawback now is that, in PCs with more than one card,
card A may complete() for a waiter on card B. But this is highly
unlikely and its impact not serious. Bus manager B may reset bus B
before the PHY config went out, but the next phy config on B should be
fine. However, with a timeout of 100ms, this situation is close to
impossible.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (34 commits)
powerpc: Wireup new syscalls
Move update_mmu_cache() declaration from tlbflush.h to pgtable.h
powerpc/pseries: Remove kmalloc call in handling writes to lparcfg
powerpc/pseries: Update arch vector to indicate support for CMO
ibmvfc: Add support for collaborative memory overcommit
ibmvscsi: driver enablement for CMO
ibmveth: enable driver for CMO
ibmveth: Automatically enable larger rx buffer pools for larger mtu
powerpc/pseries: Verify CMO memory entitlement updates with virtual I/O
powerpc/pseries: vio bus support for CMO
powerpc/pseries: iommu enablement for CMO
powerpc/pseries: Add CMO paging statistics
powerpc/pseries: Add collaborative memory manager
powerpc/pseries: Utilities to set firmware page state
powerpc/pseries: Enable CMO feature during platform setup
powerpc/pseries: Split retrieval of processor entitlement data into a helper routine
powerpc/pseries: Add memory entitlement capabilities to /proc/ppc64/lparcfg
powerpc/pseries: Split processor entitlement retrieval and gathering to helper routines
powerpc/pseries: Remove extraneous error reporting for hcall failures in lparcfg
powerpc: Fix compile error with binutils 2.15
...
Fixed up conflict in arch/powerpc/platforms/52xx/Kconfig manually.
|
|
* 'linux-next' of git://git.infradead.org/~dedekind/ubi-2.6: (22 commits)
UBI: always start the background thread
UBI: fix gcc warning
UBI: remove pre-sqnum images support
UBI: fix kernel-doc errors and warnings
UBI: fix checkpatch.pl errors and warnings
UBI: bugfix - do not torture PEB needlessly
UBI: rework scrubbing messages
UBI: implement multiple volumes rename
UBI: fix and re-work debugging stuff
UBI: amend commentaries
UBI: fix error message
UBI: improve mkvol request validation
UBI: add ubi_sync() interface
UBI: fix 64-bit calculations
UBI: fix LEB locking
UBI: fix memory leak on error path
UBI: do not forget to free internal volumes
UBI: fix memory leak
UBI: avoid unnecessary division operations
UBI: fix buffer padding
...
|
|
The new type checking of the flags arguments to irqsave and friends
(commit 3f307891ce0e7b0438c432af1aacd656a092ff45) pointed out this thing
with a big nice warning.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Convert PCI err device from platform to open firmware of_dev to comply
with powerpc schemes.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fixup of missing bit 0 on 64360 PCIx_ERR_MASK and errata FEr-#11 and
FEr-#16 for the 64460. Bit 0 must remain 0.
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Doug Thompson <dougthompson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Update get_property() call to use of_get_property() in order to fix compile
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Doug Thompson <dougthompson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This module harvests more than just memory errors, it also harvests
various bus and dma errors that the Chipset detects. Previously, it would
report all such errors, which would cause output to be TOO loud.
This patches therefore adds a parameter which is used to turn off
NON-MEMORY error reports by default. Or the reporting can be enabled via
the parameter
Also did code style cleanup: less than 80 characters per line rule
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The channel DIMM label does not seem to be used much in the edac code.
However, where it is used (in the core code), it is assumed to not have a
newline embedded. This leaves the sysfs file newline free which looks
funny when cat'ing it. Here we just add the trailing newline to the sysfs
chX_dimm_label output...
[Doug Thompson note: the DIMM label is one of the primary uses of EDAC.
User space daemon scripts, edac-utils@sourceforge, populate the DIMM label
fields, via /sys/devices/system/edac attributes, with the silk screen
labels of the motherboard in use. dmidecode access BIOS tables, but BIOS
tables are well known to be incorrect and useless in these respects.
edac-utils will strip off any newlines before its use of the output, when
displaying DIMM slot silk screen labels.
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Static kobjects and ksets are not supported in Linux kernel. Convert the
mc_kset from static to dynamic. This patch depends on my previous patch
to remove the module parameter attributes from mc...
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
/sys/devices/system/edac/mc has a few files which are duplicated in
/sys/module/edac_core/parameters. Now that all the functionality is
duplicated between these two locations, we remove the former kobject
attributes and update the documentation.
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When updating the edac_mc_poll_msec module parameter from the sysfs
/sys/module/edac_core/parameters/edac_mc_poll_msec file, we don't update
the workq timers. So that, if we move from a big poll time to a small
one, the small one won't take effect until the big one has timed out.
Here we provide a new module parameter set method to call out to the
update routine. This brings the /sys/module/edac_core/parameters
functionality up to that provided by the /sys/drivers/system/edac/mc sysfs
module parameter files so that we can remove them or at least link to the
/sys/module files...
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Static kobjects are not supported in linux kernel. Convert the
edac_pci_top_main_kobj from static to dynamic. This avoids the double
free of the edac_pci_top_main_kobj.name that we see on module reload of
the e752x edac driver (and probably others as well).
In addition Greg KH <greg@kroah.com> has pointed out that this code may be
cleaned up significantly. I will look at that as a follow-on patch, for
now, I just want the minimum fix to get this double-free oops bug
squashed...
Many thanks to Greg KH for his patience in showing me what the
Documentation/kobject.txt already said (oops)...
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Some code cleanliness issues found by Andrew Morton (thanks!) which should
not affect functionality, but which should help make the code more
maintainable.
In particular, we now:
* convert all #define's w/ a parameter to static inlines
* use 1UL rather than 1ULL when calculating an unsigned long
* use pci_disable_device
The resulting code is tested and seems to work fine...
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Cc: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Explicitly unmask ECC errors we are interested in reporting.
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
It is possible that the BIOS did not enable ECC at boot time. We check
for that case and fail to load if it is true.
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The error mask we use to trigger ECC notifications is missing many bits of
interest. We add these bits here so that all possible ECC errors can be
reported.
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Preliminary support for the Intel 5100 MCH. CE and UE errors are reported
along with the current DIMM label information and other memory parameters.
Reasons why this is preliminary:
1) This chip has 2 independent memory controllers which, for best
perforance, use interleaved accesses to the DDR2 memory. This
architecture does not map very well to the current edac data structures
which depend on symmetric channel access to the interleaved data.
Without core changes, the best I could do for now is to map both memory
controllers to different csrows (first all ranks of controller 0, then
all ranks of controller 1). Someone much more familiar with the edac
core than I will probably need to come up with a more general data
structure to handle the interleaving and de-interleaving of the two
memory controllers.
2) I have not yet tackled the de-interleaving of the rank/controller
address space into the physical address space of the CPU. There is
nothing fundamentally missing, it is just ending up to be a lot of
code, and I'd rather keep it separate for now, esp since it doesn't
work yet...
3) The code depends on a particular i5100 chip select to DIMM mainboard
chip select mapping. This mapping seems obvious to me in order to
support dual and single ranked memory, but it is not unique and DIMM
labels could be wrong on other mainboards. There is no way to query
this mapping that I know of.
4) The code requires that the i5100 is in 32GB mode. Only 4 ranks per
controller, 2 ranks per DIMM are supported. I do not have hardware
(nor do I expect to have hardware anytime soon) for the 48GB (6 ranks
per controller) mode.
5) The serial presence detect code should be broken out into a "real"
i2c driver so that decode-dimms.pl can work.
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
ATA over Ethernet: The semaphore emsgs_sema is used for signalling an
event, convert it in a completion.
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Cc: "Ed L. Cashin" <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
With the removal of the Solaris binary emulation the export of
proc_clear_tty became unused.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Abhay Salunke <Abhay_Salunke@dell.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Doug Warzecha <Douglas_Warzecha@dell.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Markus Rechberger <markus.rechberger@amd.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Tell users that the driver is only for PCI devices to stop asking for
support of firewire and parallel devices.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
- remove unused macro
- some whitespace cleanup
- useless debug prints removal
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove a support of ISA addresses predefined at compile time. It is
unused (filled by zeroes) and prolongs the code. Don't initialize global
array and add `ioaddr' module param description.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
- use dev_* for printing in pci probe function
- move ISA p[rints directly into isa find function, do not postpone it.
Remove macros bound to it then.
- prepend some prints by "mxser: " to know what it belongs to
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|