| Age | Commit message (Collapse) | Author |
|---|
|
Quite a few ASUS computers experience a nasty problem, related to the
EHCI controllers, when going into system suspend. It was observed
that the problem didn't occur if the controllers were not put into the
D3 power state before starting the suspend, and commit
151b61284776be2d6f02d48c23c3625678960b97 (USB: EHCI: fix crash during
suspend on ASUS computers) was created to do this.
It turned out this approach messed up other computers that didn't have
the problem -- it prevented USB wakeup from working. Consequently
commit c2fb8a3fa25513de8fedb38509b1f15a5bbee47b (USB: add
NO_D3_DURING_SLEEP flag and revert 151b61284776be2) was merged; it
reverted the earlier commit and added a whitelist of known good board
names.
Now we know the actual cause of the problem. Thanks to AceLan Kao for
tracking it down.
According to him, an engineer at ASUS explained that some of their
BIOSes contain a bug that was added in an attempt to work around a
problem in early versions of Windows. When the computer goes into S3
suspend, the BIOS tries to verify that the EHCI controllers were first
quiesced by the OS. Nothing's wrong with this, but the BIOS does it
by checking that the PCI COMMAND registers contain 0 without checking
the controllers' power state. If the register isn't 0, the BIOS
assumes the controller needs to be quiesced and tries to do so. This
involves making various MMIO accesses to the controller, which don't
work very well if the controller is already in D3. The end result is
a system hang or memory corruption.
Since the value in the PCI COMMAND register doesn't matter once the
controller has been suspended, and since the value will be restored
anyway when the controller is resumed, we can work around the BIOS bug
simply by setting the register to 0 during system suspend. This patch
(as1590) does so and also reverts the second commit mentioned above,
which is now unnecessary.
In theory we could do this for every PCI device. However to avoid
introducing new problems, the patch restricts itself to EHCI host
controllers.
Finally the affected systems can suspend with USB wakeup working
properly.
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=37632
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=42728
Based-on-patch-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Dâniel Fraga <fragabr@gmail.com>
Tested-by: Javier Marcet <jmarcet@gmail.com>
Tested-by: Andrey Rahmatullin <wrar@wrar.name>
Tested-by: Oleksij Rempel <bug-track@fisher-privat.net>
Tested-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Cc: stable <stable@vger.kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Clear the WDM_READ flag on empty reads to avoid running
forever in an infinite tight loop, causing lockups:
Jul 1 21:58:11 nemi kernel: [ 3658.898647] qmi_wwan 2-1:1.2: Unexpected error -71
Jul 1 21:58:36 nemi kernel: [ 3684.072021] BUG: soft lockup - CPU#0 stuck for 23s! [qmi.pl:12235]
Jul 1 21:58:36 nemi kernel: [ 3684.072212] CPU 0
Jul 1 21:58:36 nemi kernel: [ 3684.072355]
Jul 1 21:58:36 nemi kernel: [ 3684.072367] Pid: 12235, comm: qmi.pl Tainted: P O 3.5.0-rc2+ #13 LENOVO 2776LEG/2776LEG
Jul 1 21:58:36 nemi kernel: [ 3684.072383] RIP: 0010:[<ffffffffa0635008>] [<ffffffffa0635008>] spin_unlock_irq+0x8/0xc [cdc_wdm]
Jul 1 21:58:36 nemi kernel: [ 3684.072388] RSP: 0018:ffff88022dca1e70 EFLAGS: 00000282
Jul 1 21:58:36 nemi kernel: [ 3684.072393] RAX: ffff88022fc3f650 RBX: ffffffff811c56f7 RCX: 00000001000ce8c1
Jul 1 21:58:36 nemi kernel: [ 3684.072398] RDX: 0000000000000010 RSI: 000000000267d810 RDI: ffff88022fc3f650
Jul 1 21:58:36 nemi kernel: [ 3684.072403] RBP: ffff88022dca1eb0 R08: ffffffffa063578e R09: 0000000000000000
Jul 1 21:58:36 nemi kernel: [ 3684.072407] R10: 0000000000000008 R11: 0000000000000246 R12: 0000000000000002
Jul 1 21:58:36 nemi kernel: [ 3684.072412] R13: 0000000000000246 R14: ffffffff00000002 R15: ffff8802281d8c88
Jul 1 21:58:36 nemi kernel: [ 3684.072418] FS: 00007f666a260700(0000) GS:ffff88023bc00000(0000) knlGS:0000000000000000
Jul 1 21:58:36 nemi kernel: [ 3684.072423] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
Jul 1 21:58:36 nemi kernel: [ 3684.072428] CR2: 000000000270d9d8 CR3: 000000022e865000 CR4: 00000000000007f0
Jul 1 21:58:36 nemi kernel: [ 3684.072433] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
Jul 1 21:58:36 nemi kernel: [ 3684.072438] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Jul 1 21:58:36 nemi kernel: [ 3684.072444] Process qmi.pl (pid: 12235, threadinfo ffff88022dca0000, task ffff88022ff76380)
Jul 1 21:58:36 nemi kernel: [ 3684.072448] Stack:
Jul 1 21:58:36 nemi kernel: [ 3684.072458] ffffffffa063592e 0000000100020000 ffff88022fc3f650 ffff88022fc3f6a8
Jul 1 21:58:36 nemi kernel: [ 3684.072466] 0000000000000200 0000000100000000 000000000267d810 0000000000000000
Jul 1 21:58:36 nemi kernel: [ 3684.072475] 0000000000000000 ffff880212cfb6d0 0000000000000200 ffff880212cfb6c0
Jul 1 21:58:36 nemi kernel: [ 3684.072479] Call Trace:
Jul 1 21:58:36 nemi kernel: [ 3684.072489] [<ffffffffa063592e>] ? wdm_read+0x1a0/0x263 [cdc_wdm]
Jul 1 21:58:36 nemi kernel: [ 3684.072500] [<ffffffff8110adb7>] ? vfs_read+0xa1/0xfb
Jul 1 21:58:36 nemi kernel: [ 3684.072509] [<ffffffff81040589>] ? alarm_setitimer+0x35/0x64
Jul 1 21:58:36 nemi kernel: [ 3684.072517] [<ffffffff8110aec7>] ? sys_read+0x45/0x6e
Jul 1 21:58:36 nemi kernel: [ 3684.072525] [<ffffffff813725f9>] ? system_call_fastpath+0x16/0x1b
Jul 1 21:58:36 nemi kernel: [ 3684.072557] Code: <66> 66 90 c3 83 ff ed 89 f8 74 16 7f 06 83 ff a1 75 0a c3 83 ff f4
The WDM_READ flag is normally cleared by wdm_int_callback
before resubmitting the read urb, and set by wdm_in_callback
when this urb returns with data or an error. But a crashing
device may cause both a read error and cancelling all urbs.
Make sure that the flag is cleared by wdm_read if the buffer
is empty.
We don't clear the flag on errors, as there may be pending
data in the buffer which should be processed. The flag will
instead be cleared on the next wdm_read call.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Do not set low_latency flag at open as tty_flip_buffer_push must not be
called in IRQ context with low_latency set.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Gaosen Zhang <gaosen.zhang@mediatek.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Switches into a composite device by ejecting the initial
driver CD. The four interfaces are: QCDM, AT, QMI/wwan
and mass storage. Let this driver manage the two serial
interfaces:
T: Bus=02 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 28 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=19d2 ProdID=1402 Rev= 0.00
S: Manufacturer=ZTE,Incorporated
S: Product=ZTE WCDMA Technologies MSM
S: SerialNumber=xxxxx
C:* #Ifs= 4 Cfg#= 1 Atr=c0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Microsoft LifeChat 3000 USB headset was causing a very reproducible
hang whenever it was plugged in. At first, I thought the host
controller was producing bad transfer events, because the log was filled
with errors like:
xhci_hcd 0000:00:14.0: ERROR Transfer event TRB DMA ptr not part of current TD
However, it turned out to be an xHCI driver bug in the ring expansion
patches. The bug is triggered When there are two ring segments, and a
TD that ends just before a link TRB, like so:
______________ _____________
| | ---> | setup TRB B |
______________ | _____________
| | | | data TRB B |
______________ | _____________
| setup TRB A | <-- deq | | data TRB B |
______________ | _____________
| data TRB A | | | | <-- enq, deq''
______________ | _____________
| status TRB A | | | |
______________ | _____________
| link TRB |--------------- | link TRB |
_____________ <--- deq' _____________
TD A (the first control transfer) stalls on the data phase. That halts
the ring. The xHCI driver moves the hardware dequeue pointer to the
first TRB after the stalled transfer, which happens to be the link TRB.
Once the Set TR dequeue pointer command completes, the function
update_ring_for_set_deq_completion runs. That function is supposed to
update the xHCI driver's dequeue pointer to match the internal hardware
dequeue pointer. On the first call this would work fine, and the
software dequeue pointer would move to deq'.
However, if the transfer immediately after that stalled (TD B in this
case), another Set TR Dequeue command would be issued. That would move
the hardware dequeue pointer to deq''. Once that command completed,
update_ring_for_set_deq_completion would run again.
The original code would unconditionally increment the software dequeue
pointer, which moved the pointer off the ring segment into la-la-land.
The while loop would happy increment the dequeue pointer (possibly
wrapping it) until it matched the hardware pointer value.
The while loop would also access all the memory in between the first
ring segment and the second ring segment to determine if it was a link
TRB. This could cause general protection faults, although it was
unlikely because the ring segments came from a DMA pool, and would often
have consecutive memory addresses.
If nothing in that space looked like a link TRB, the deq_seg pointer for
the ring would remain on the first segment. Thus, the deq_seg and the
software dequeue pointer would get out of sync.
When the next transfer event came in after the stalled transfer, the
xHCI driver code would attempt to convert the software dequeue pointer
into a DMA address in order to compare the DMA address for the completed
transfer. Since the deq_seg and the dequeue pointer were out of sync,
xhci_trb_virt_to_dma would return NULL.
The transfer event would get ignored, the transfer would eventually
timeout, and we would mistakenly convert the finished transfer to no-op
TRBs. Some kernel driver (maybe xHCI?) would then get stuck in an
infinite loop in interrupt context, and the whole machine would hang.
This patch should be backported to kernels as old as 3.4, that contain
the commit b008df60c6369ba0290fa7daa177375407a12e07 "xHCI: count free
TRBs on transfer ring"
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Andiry Xu <andiry.xu@amd.com>
Cc: stable@vger.kernel.org
|
|
The host controller port status register supports CAS (Cold Attach
Status) bit. This bit could be set when USB3.0 device is connected
when system is in Sx state. When the system wakes to S0 this port
status with CAS bit is reported and this port can't be used by any
device.
When CAS bit is set the port should be reset by warm reset. This
was not supported by xhci driver.
The issue was found when pendrive was connected to suspended
platform. The link state of "Compliance Mode" was reported together
with CAS bit. This link state was also not supported by xhci and
core/hub.c.
The CAS bit is defined only for xhci root hub port and it is
not supported on regular hubs. The link status is used to force
warm reset on port. Make the USB core issue a warm reset when port
is in ether the 'inactive' or 'compliance mode'. Change the xHCI driver
to report 'compliance mode' when the CAS is set. This force warm reset
on the root hub port.
This patch should be backported to stable kernels as old as 3.2, that
contain the commit 10d674a82e553cb8a1f41027bb3c3e309b3f6804 "USB: When
hot reset for USB3 fails, try warm reset."
Signed-off-by: Stanislaw Ledwon <staszek.ledwon@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Andiry Xu <andiry.xu@amd.com>
Cc: stable@vger.kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Pull ACPI & Power Management patches from Len Brown.
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
acpi_pad: fix power_saving thread deadlock
ACPI video: Still use ACPI backlight control if _DOS doesn't exist
ACPI, APEI, Avoid too much error reporting in runtime
ACPI: Add a quirk for "AMILO PRO V2030" to ignore the timer overriding
ACPI: Remove one board specific WARN when ignoring timer overriding
ACPI: Make acpi_skip_timer_override cover all source_irq==0 cases
ACPI, x86: fix Dell M6600 ACPI reboot regression via DMI
ACPI sysfs.c strlen fix
|
|
'video-bugzilla-43168', 'bugzilla-40002' and 'bugfix-misc' into release
bug fixes
|
|
The acpi_pad driver can get stuck in destroy_power_saving_task()
waiting for kthread_stop() to stop a power_saving thread. The problem
is that the isolated_cpus_lock mutex is owned when
destroy_power_saving_task() calls kthread_stop(), which waits for a
power_saving thread to end, and the power_saving thread tries to
acquire the isolated_cpus_lock when it calls round_robin_cpu(). This
patch fixes the issue by making round_robin_cpu() use its own mutex.
https://bugzilla.kernel.org/show_bug.cgi?id=42981
Cc: stable@vger.kernel.org
Signed-off-by: Stuart Hayes <Stuart_Hayes@Dell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
This fixes a regression in 3.4-rc1 caused by commit
ea9f8856bd6d4ed45885b06a338f7362cd6c60e5
(ACPI video: Harden video bus adding.)
Some platforms don't have _DOS control method, but the ACPI
backlight still works.
We should not invoke _DOS for these platforms.
https://bugzilla.kernel.org/show_bug.cgi?id=43168
Cc: Igor Murzov <intergalactic.anonymous@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael J. Wysocki:
* Fix for a bug in async suspend error code path causing parents to
wait forever for their children in case of a suspend error from
Mandeep Singh Baines (-stable metarial).
* Fix for a suspend regression related to earlier changes in the ACPI
cpuidle driver from Deepthi Dharwar.
* tag 'pm-for-3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / ACPI: Fix suspend/resume regression caused by cpuidle cleanup.
PM / Sleep: Prevent waiting forever on asynchronous suspend after abort
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar.
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, cpufeature: Remove stray %s, add -w to mkcapflags.pl
x86, cpufeature: Catch duplicate CPU feature strings
x86, cpufeature: Rename X86_FEATURE_DTS to X86_FEATURE_DTHERM
x86: Fix kernel-doc warnings
x86, compat: Use test_thread_flag(TIF_IA32) in compat signal delivery
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull oprofile fixlet from Ingo Molnar.
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
oprofile: perf: use NR_CPUS instead or nr_cpumask_bits for static array
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon changes from Guenter Roeck:
"Just e-mail address updates"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: Update my e-mail address
hwmon: (applesmc) correct email address for Jesper Juhl
|
|
Pull watchdog fixes from Wim Van Sebroeck:
"This fixes:
- the WDIOC_GETSTATUS return value
- the unregister of all NMI events on exit
- the loading of the iTCO_wdt driver after the conversion to the
lpc_ich mfd model."
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: core: fix WDIOC_GETSTATUS return value
watchdog: hpwdt: Unregister NMI events on exit.
watchdog: iTCO_wdt: add platform driver module alias
|
|
Pull ubi/ubifs fixes from Artem Bityutskiy:
"Fix the debugfs regression - we never enable it because incorrect
'IS_ENABLED()' macro usage: should be 'IS_ENABLED(CONFIG_DEBUG_FS)',
but we had 'IS_ENABLED(DEBUG_FS)'. Also fix incorrect assertion."
* tag 'upstream-3.5-rc5' of git://git.infradead.org/linux-ubifs:
UBI: correct usage of IS_ENABLED()
UBIFS: correct usage of IS_ENABLED()
UBIFS: fix assertion
|
|
In commit 7a87982420e5e126bfefeb42232d1fd92052794e we added
a wrapper for the WDIOC_GETSTATUS ioctl call. The code results
however in a different behaviour: it returns an error if the
driver doesn't support the status operation. This is not
according to the API that says that when we don't support
the status operation, that we just should return a 0 value.
Only when the device isn't there anymore, we should return an
error.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
This patch is to unregister for NMI events upon exit. Also we are now
making the default setting for allow_kdump enabled.
Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
The recent conversion of iTCO_wdt resulted in the driver no longer
getting loaded automatically, since it no longer has a
MODULE_DEVICE_TABLE() included. As the lpc_ich driver now creates a
platform device, auto-loading can easily be done by having a respective
module alias in place.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Aaron Sierra <asierra@xes-inc.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Pull drm fixes from Dave Airlie:
"Nearly all intel, one missing license header in nouveau, nothing
majorly earth shattering."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
Revert "drm/i915: allow PCH PWM override on IVB"
drm/nouveau: add license header to prime.
drm/i915: Fix eDP blank screen after S3 resume on HP desktops
drm/i915: rip out the PM_IIR WARN
|
|
Pull networking update from David Miller:
1) Pairing and deadlock fixes in bluetooth from Johan Hedberg.
2) Add device IDs for AR3011 and AR3012 bluetooth chips. From
Giancarlo Formicuccia and Marek Vasut.
3) Fix wireless regulatory deadlock, from Eliad Peller.
4) Fix full TX ring panic in bnx2x driver, from Eric Dumazet.
5) Revert the two commits that added skb_orphan_try(), it causes
erratic bonding behavior with UDP clients and the gains it used to
give are mostly no longer happening due to how BQL works. From Eric
Dumazet.
6) It took two tries, but Thomas Graf fixed a problem wherein we
registered ipv6 routing procfs files before their backend data were
initialized properly.
7) Fix max GSO size setting in be2net, from Sarveshwar Bandi.
8) PHY device id mask is wrong for KSZ9021 and KS8001 chips, fix from
Jason Wang.
9) Fix use of stale SKB data pointer after skb_linearize() call in
batman-adv, from Antonio Quartulli.
10) Fix memory leak in IXGBE due to missing __GFP_COMP, from Alexander
Duyck.
11) Fix probing of Gobi devices in qmi_wwan usbnet driver, from Bjørn
Mork.
12) Fix suspend/resume and open failure handling in usbnet from Ming
Lei.
13) Attempt to fix device r8169 hangs for certain chips, from Francois
Romieu.
14) Fix advancement of RX dirty pointer in some situations in sh_eth
driver, from Yoshihiro Shimoda.
15) Attempt to fix restart of IPV6 routing table dumps when there is an
intervening table update. From Eric Dumazet.
16) Respect security_inet_conn_request() return value in ipv6 TCP. From
Neal Cardwell.
17) Add another iPAD device ID to ipheth driver, from Davide Gerhard.
18) Fix access to freed SKB in l2tp_eth_dev_xmit(), and fix l2tp lockdep
splats, from Eric Dumazet.
19) Make sure all bridge devices, regardless of whether they were
created via netlink or ioctls, have their rtnetlink ops hooked up.
From Thomas Graf and Stephen Hemminger.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (81 commits)
9p: fix min_t() casting in p9pdu_vwritef()
can: flexcan: use be32_to_cpup to handle the value of dt entry
xen/netfront: teardown the device before unregistering it.
bridge: Assign rtnl_link_ops to bridge devices created via ioctl (v2)
vhost: use USER_DS in vhost_worker thread
ixgbe: Do not pad FCoE frames as this can cause issues with FCoE DDP
net: l2tp_eth: use LLTX to avoid LOCKDEP splats
mac802154: add missed braces
net: l2tp_eth: fix l2tp_eth_dev_xmit race
net/mlx4_en: Release QP range in free_resources
net/mlx4: Use single completion vector after NOP failure
net/mlx4_en: Set correct port parameters during device initialization
ipheth: add support for iPad
caif-hsi: Add missing return in error path
caif-hsi: Bugfix - Piggyback'ed embedded CAIF frame lost
caif: Clear shutdown mask to zero at reconnect.
tcp: heed result of security_inet_conn_request() in tcp_v6_conn_request()
ipv6: fib: fix fib dump restart
batman-adv: fix race condition in TT full-table replacement
batman-adv: only drop packets of known wifi clients
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are some small USB gadget bugfixes, and a few new USB device ids
added to some drivers for the 3.5-rc5 release.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: CP210x Add 10 Device IDs
USB: option: Add USB ID for Novatel Ovation MC551
usb: phy: Fix Kconfig dependency for Phy drivers
usb-storage: revert commit afff07e61a52 (Add 090c:1000 to unusal-devs)
SCSI & usb-storage: add try_rc_10_first flag
usb: musb: host: release dma channels if no active io
usb: gadget: lpc32xx_udc: fix build error with debugfs enabled
usb: otg: twl6030-usb: Fix twl writes
USB: option: add id for Cellient MEN-200
usb: dwc3: fix giveback of queued request in ep_dequeue
usb: gadget: Complete fsl qe/udc driver conversion
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC fixes from Chris Ball:
- omap_hsmmc: Using AUTO_CMD12 (enabled by default in 3.5-rc1) has
been found to cause data corruption on the BeagleBoard, but no
other OMAP boards so far. Revert the patch until there's a root
cause explanation that makes sense, at which point we might
decide to use a blacklist or whitelist.
- mmc_block: Fix incorrect data timeouts for the case of multiblock
(ACMD22) writes for block-addressed cards.
* tag 'mmc-fixes-for-3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
Revert "mmc: omap_hsmmc: Enable Auto CMD12"
mmc: block: fix the data timeout issue with ACMD22
|
|
Pull clk common framework fixes from Mike Turquette:
"This contains three NULL pointer fixes and two device regression
fixups.
Two NULL pointer dereferences were in the common clk core due to lack
of sanity checking and the third NPD was in the mxs-specific clock
code due to incorrect use of __initdata.
The device regressions were the result of improper data: a wrong
string name for matching DT data broke the SPEAr ethernet controller
and another string matching problem in the mxs clock data resulted in
a broken MMC controller."
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux:
clk: mxs: fix clock lookup after freeing init memory
clk: mxs: fix ref_io clock definition
clk: Check parent for NULL in clk_change_rate
clk: Allow late cache allocation for clk->parents
clk: SPEAr600: Fix ethernet clock name for DT based probing
|
|
git://people.freedesktop.org/~danvet/drm-intel into drm-fixes
Daniel writes:
"Two tiny patches and one revert:
- Kill a bogus error message introduced in 3.4, further Bspec reading
indicates that this is how the hw is supposed to work.
- Reorder one backlight register restore, fixing broken backlight on some
machines after resume.
- Revert a hack from Jesse for ivb backlight control - it breaks the
backlight controls on my shiny new ivb laptop."
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
Revert "drm/i915: allow PCH PWM override on IVB"
drm/i915: Fix eDP blank screen after S3 resume on HP desktops
drm/i915: rip out the PM_IIR WARN
|
|
This reverts commit f82cfb6bcda164ef3a66b8c3fc549b1f9bdd09ad.
This breaks the backlight controls on my IVB asus zenbook with an eDP
panel.
I guess the right fix would be to read this bit and use either the pch
or the cpu register to frob the backlight values. But that is stuff
for -next.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Commit e978aa7d7d57d04eb5f88a7507c4fb98577def77 ( cpuidle: Move
dev->last_residency update to driver enter routine; remove dev->last_state)
was breaking suspend on laptops, as reported in the below link
- https://lkml.org/lkml/2011/11/11/164
This was fixed in commit 3439a8da16bcad6b0982ece938c9f8299bb53584
(ACPI / cpuidle: Remove acpi_idle_suspend (to fix suspend regression)
by removing acpi_idle_suspend flag.
- https://lkml.org/lkml/2011/11/14/74
But this did fix did not work on all systems
as Suspend/resume regression was reported on Lenovo S10-3
recently by Dave.
- https://lkml.org/lkml/2012/5/27/115
It looked like with commit e978aa7d broke suspend and
with commit 3439a8da resume was not working with acpi_idle driver.
This patch fixes the regression that caused this issue
in the first place. acpi_idle_suspend flag is essential on
some x86 systems to prevent the cpus from going to deeper C-states
when suspend is triggered ( commit b04e7bdb984 )
So reverting the commit 3439a8da is essential.
By default, irqs are disabled in cpu_idle arch specific call
and re-enabled in idle state return path . During suspend,
the acpi_idle_suspend flag is set, which
prevents the cpus from going to deeper idle states,
it is essential to enabling the irqs in this return path too.
To address the suspend issue,
we were not re-enabling the interrupts while returning from
acpi_idle_enter_bm() routine if acpi_idle_suspend flag is set.
and this caused suspend failure.
In addition to the above, to improve the readability of the code,
return of -ENIVAL is replaced with -EBUSY in acpi_idle_suspend
return path. Implying that the system is currently busy when suspend
is in progress, which prevents the cpus from entering deeper C-states.
Reported-and-Tested-by: Dav Hansen <dave@linux.vnet.ibm.com>
Tested-by: Preeti Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Reviewed-by: Srivatsa S Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Commit "e9b4cf2 UBI: fix debugfs-less systems support" fixed one
regression but introduced a different regression - the debugfs is now always
compiled out. Root cause: IS_ENABLED() arguments should be used with the
CONFIG_* prefix.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
The freescale arm i.MX series platform can support this driver, and
usually the arm cpu works in the little endian mode by default, while
device tree entry value is stored in big endian format, we should use
be32_to_cpup() to handle them, after modification, it can work well
both on the le cpu and be cpu.
Cc: stable <stable@vger.kernel.org> # v3.2+
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Hui Wang <jason77.wang@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Just forgot this when I posted it, and yes I'm the only person
to have changed the file since.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Fixes:
[ 15.470311] WARNING: at /local/scratch/ianc/devel/kernels/linux/fs/sysfs/file.c:498 sysfs_attr_ns+0x95/0xa0()
[ 15.470326] sysfs: kobject eth0 without dirent
[ 15.470333] Modules linked in:
[ 15.470342] Pid: 12, comm: xenwatch Not tainted 3.4.0-x86_32p-xenU #93
and
[ 9.150554] BUG: unable to handle kernel paging request at 2b359000
[ 9.150577] IP: [<c1279561>] linkwatch_do_dev+0x81/0xc0
[ 9.150592] *pdpt = 000000002c3c9027 *pde = 0000000000000000
[ 9.150604] Oops: 0002 [#1] SMP
[ 9.150613] Modules linked in:
This is http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=675190
Reported-by: George Shuklin <george.shuklin@gmail.com>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Tested-by: William Dauchy <wdauchy@gmail.com>
Cc: stable@kernel.org
Cc: 675190@bugs.debian.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On some architectures address spaces are set up in a way that this is
not necessary to work properly but on some others (like s390) it is.
Make sure we operate on the user address space to allow copy_xxx_user()
from the vhost_worker() thread by setting it explicitly before calling
use_mm() and revert it after unuse_mm().
Signed-off-by: Jens Freimann <jfrei@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
FCoE target mode was experiencing issues due to the fact that we were
sending up data frames that were padded to 60 bytes after the DDP logic had
already stripped the frame down to 52 or 56 depending on the use of VLANs.
This was resulting in the FCoE DDP logic having issues since it thought the
frame still had data in it due to the padding.
To resolve this, adding code so that we do not pad FCoE frames prior to
handling them to the stack.
CC: <stable@vger.kernel.org>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds 10 device IDs for CP210x based devices from the following manufacturers:
Timewave
Clipsal
Festo
Link Instruments
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This device is also known as the Verizon USB551L.
Signed-off-by: Forest Bond <forest.bond@rapidrollout.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
USB phy layer driver are only built if usb host is selected, but they
are used too by USB_GADGET drivers
Signed-off-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch reverts the commit dba3c29ea4a1d5d544.
After bisecting, this commit dba3c29 is found to ruin micro-SD card data
(writing incorrect file, or fs is corrupt after several times mount)
on the beagle-xm revB, and reverting the commit will fix the problem.
Also from TRM of OMAP3/OMAP4/DM37x, the below is mentioned about
the Auto CMD12 Enable bit.
- SDIO does not support this feature.
- SD card only.
Looks it is not suitable to always enable Auto CMD12 in host controller
driver.
Considered that the commit is not mature enough, so ask to revert it
first.
Cc: Balaji T K <balajitk@ti.com>
Cc: Venkatraman S <svenkatr@ti.com>
Buglink: https://lkml.org/lkml/2012/6/10/225
Reported-by: Paolo Pisati <p.pisati@gmail.com>
Reported-bisected-and-tested-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
If multi block write operation fails for SD card, during
error handling we send the SD_APP_SEND_NUM_WR_BLKS (ACMD22)
to know how many blocks were already programmed by card.
But mmc_sd_num_wr_blocks() function which sends the ACMD22
calculates the data timeout value from csd.tacc_ns and
csd.tacc_clks parameters which will be 0 for block addressed
(>2GB cards) SD card. This would result in timeout_ns and
timeout_clks being 0 in the mmc_request passed to host driver.
This means host controller would program its data timeout timer
value with 0 which could result in DATA TIMEOUT errors from
controller.
To fix this issue, mmc_sd_num_wr_blocks() should instead
just call the mmc_set_data_timeout() to calculate the
data timeout value. mmc_set_data_timeout() function
ensures that non zero timeout value is set even for
block addressed SD cards.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Pull drm fixes from Dave Airlie:
"Just two changes: one udl endian fix, one nouveau memory corruption on
some GPUs."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau/fbcon: using nv_two_heads is not a good idea
drm/udl: Make sure to get correct endian keys from vendor descriptor
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
"The most important one is a purification of Kconfig for CONFIG_HID;
the inclusion of HID groups and autoloading didn't leave the Kconfig
in a really consistent state. Henrik's patch fixes that. In addition
to that, there are two small fixes for logitech and magicmouse
drivers."
* 'upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: Fix the generic Kconfig options
HID: magicmouse: Correct report range of major / minor axes
HID: logitech: don't use stack based dj_report structures
|
|
nv_two_heads() was never meant to be used outside of pre-nv50 code. The
code checks for >= NV_10 for 2 CRTCs, then downgrades a few specific
chipsets to 1 CRTC based on (pci_device & 0x0ff0).
The breakage example seen is on GTX 560Ti, with a pciid of 0x1200, which
gets detected as an NV20 (0x020x) with 1 CRTC by nv_two_heads(), causing
memory corruption because there's actually 2 CRTCs..
This switches fbcon to use the CRTC count directly from the mode_config
structure, which will also fix the same issue on Kepler boards which have
4 CRTCs.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The struct clk_lookup are marked as __initdata, resulting in being
removed from memory after the kernel finished booting. However this
leads to a NULL pointer de-ref if loading a module which uses clk_get.
This patch removes the __initdata from the struct clk_lookup.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
The definition of clocks ref_io0 and ref_io1 were inverted. It causes
a mmc regression on some boards right away. Fix the regression by
correcting the ref_io clock definition.
Reported-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
clk_change_rate() is accessing parent's rate without checking
if the parent exists at all. In case of root clocks this will
cause NULL pointer dereference.
This patch follows what clk_calc_new_rates() does in such
situation.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Cc: stable@kernel.org
|
|
Parent clocks for muxes are cached in clk->parents to
avoid frequent lookups, however the cache allocation happens
only during clock registeration and later clk_set_parent()
assumes a cache space available and allocated.
This is not entirely true for platforms which do early clock
registerations wherein the cache allocation using kzalloc
could fail during clock registeration.
Allow cache allocation to happen later as part of clk_set_parent()
to help such cases and avoid crashes assuming a cache being
available.
While here also replace existing kmalloc() with kzalloc()
in the file.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Cc: stable@kernel.org
|
|
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Viresh Kumar <viresh.kumar@st.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Add a missing resource release in ring cleanup.
Not doing this leaves a range of QPs that are being reserved,
and no one can use them.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix a crash at the error flow of NOP command which caused the driver to try and use
a completion vector which wasn't allocated.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set valid port parameters: MTU and flow control configuration when
configuring the port during HW device initialization,
prior to the net device open() being called.
Using invalid parameters (such as all zeros)
could lead to bad firmware behavior.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
