Age | Commit message (Collapse) | Author |
|
At least one board using the FEC driver does not have a conventional
PHY attached to it, it is directly connected to a somewhat simple
ethernet switch (the board is the SnapGear/LITE, and the attached
4-port ethernet switch is a RealTek RTL8305). This switch does not
present the usual register interface of a PHY, it presents nothing.
So a PHY scan will find nothing - it finds ID's of 0 for each PHY
on the attached MII bus.
After the FEC driver was changed to use phylib for supporting PHYs
it no longer works on this particular board/switch setup.
Add code support to use a fixed phy if no PHY is found on the MII bus.
This is based on the way the cpmac.c driver solved this same problem.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 511d22247be7 (tg3: 64 bit stats on all arches), overlooked the
rx_dropped accounting.
We use a full "struct rtnl_link_stats64" to hold rx_dropped value, but
forgot to report it in tg3_get_stats64().
Use an "unsigned long" instead to shrink "struct tg3" by 176 bytes, and
report this value to stats readers.
Increment rx_dropped counter for oversized frames.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Michael Chan <mchan@broadcom.com>
CC: Matt Carlson <mcarlson@broadcom.com>
Acked-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For carrier detection to work properly when binding the driver with a cable
unplugged, netif_carrier_off() should be called after register_netdev(),
not before.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Stanse found that i2400m_rx frees skb, but still uses skb->len even
though it has skb_len defined. So use skb_len properly in the code.
And also define it unsinged int rather than size_t to solve
compilation warnings.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: linux-wimax@intel.com
Acked-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Stanse found that ia_init_one locks a spinlock and inside of that it
calls ia_start which calls:
* request_irq
* tx_init which does kmalloc(GFP_KERNEL)
Both of them can thus sleep and result in a deadlock. I don't see a
reason to have a per-device spinlock there which is used only there
and inited right before the lock location. So remove it completely.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Stanse found we do in console_show:
kfree_skb(skb);
return skb->len;
which is not good. Fix that by remembering the len and use it in the
function instead.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Chas Williams <chas@cmf.nrl.navy.mil>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
with hardware slow in negotiation, the system did freeze
while trying to mount root on nfs at boot time.
the link state has not been initialised so network stack
tried to start transmission right away. this caused instant
retries, as the driver solely stated business upon link down,
rendering the system unusable.
notify carrier off initially to prevent transmission until
phylib will report link up.
Signed-off-by: Oskar Schirmer <oskar@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use DMA API as PCI equivalents will be deprecated. This change also
allow to allocate with GFP_KERNEL where possible.
Tested-by: Neal Becker <ndbecker2@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We have fedora bug report where driver fail to initialize after
suspend/resume because of memory allocation errors:
https://bugzilla.redhat.com/show_bug.cgi?id=629158
To fix use GFP_KERNEL allocation where possible.
Tested-by: Neal Becker <ndbecker2@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
setup.phone and setup.eazmsn are 32 character buffers.
rcvmsg.msg_data.byte_array is a 48 character buffer.
sc_adapter[card]->channel[rcvmsg.phy_link_no - 1].dn is 50 chars.
The rcvmsg struct comes from the memcpy_fromio() in receivemessage().
I guess that means it's data off the wire. I'm not very familiar with
this code but I don't see any reason to assume these strings are NULL
terminated.
Also it's weird that "dn" in a 50 character buffer but we only seem to
use 32 characters. In drivers/isdn/sc/scioc.h, "dn" is only a 49
character buffer. So potentially there is still an issue there.
The important thing for now is to prevent the memory corruption.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/torvalds/linux-2.6
|
|
wireless-testing
commit 37e5bf6535a4d697fb9fa6f268a8354a612cbc00
Author: Luis R. Rodriguez <lrodriguez@atheros.com>
Date: Sat Jun 12 00:33:40 2010 -0400
ath9k_hw: fix clock rate calculations for ANI
This commit accidentally broke clock rate calculation by doubling the
calculated clock rate
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://xenbits.xen.org/people/sstabellini/linux-pvhvm
* 'v2.6.36-rc6-urgent-fixes' of git://xenbits.xen.org/people/sstabellini/linux-pvhvm:
xen: do not initialize PV timers on HVM if !xen_have_vector_callback
xen: do not set xenstored_ready before xenbus_probe on hvm
|
|
Fix a WARN_ON failure in bond_masters sysfs file
Got a report of this warning recently
bonding: bond0 is being created...
------------[ cut here ]------------
WARNING: at fs/proc/generic.c:590 proc_register+0x14d/0x185()
Hardware name: ProLiant BL465c G1
proc_dir_entry 'bonding/bond0' already registered
Modules linked in: bonding ipv6 tg3 bnx2 shpchp amd64_edac_mod edac_core
ipmi_si
ipmi_msghandler serio_raw i2c_piix4 k8temp edac_mce_amd hpwdt microcode hpsa
cc
iss radeon ttm drm_kms_helper drm i2c_algo_bit i2c_core [last unloaded:
scsi_wai
t_scan]
Pid: 935, comm: ifup-eth Not tainted 2.6.33.5-124.fc13.x86_64 #1
Call Trace:
[<ffffffff8104b54c>] warn_slowpath_common+0x77/0x8f
[<ffffffff8104b5b1>] warn_slowpath_fmt+0x3c/0x3e
[<ffffffff8114bf0b>] proc_register+0x14d/0x185
[<ffffffff8114c20c>] proc_create_data+0x87/0xa1
[<ffffffffa0211e9b>] bond_create_proc_entry+0x55/0x95 [bonding]
[<ffffffffa0215e5d>] bond_init+0x95/0xd0 [bonding]
[<ffffffff8138cd97>] register_netdevice+0xdd/0x29e
[<ffffffffa021240b>] bond_create+0x8e/0xb8 [bonding]
[<ffffffffa021c4be>] bonding_store_bonds+0xb3/0x1c1 [bonding]
[<ffffffff812aec85>] class_attr_store+0x27/0x29
[<ffffffff8115423d>] sysfs_write_file+0x10f/0x14b
[<ffffffff81101acf>] vfs_write+0xa9/0x106
[<ffffffff81101be2>] sys_write+0x45/0x69
[<ffffffff81009b02>] system_call_fastpath+0x16/0x1b
---[ end trace a677c3f7f8b16b1e ]---
bonding: Bond creation failed.
It happens because a user space writer to bond_master can try to
register an already existing bond interface name. Fix it by teaching
bond_create to check for the existance of devices with that name first
in cases where a non-NULL name parameter has been passed in
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Skge devices installed on some Gigabyte motherboards are not able to
perform 64 dma correctly due to board PCI implementation, so limit
DMA to 32bit if such boards are detected.
Bug was reported here:
https://bugzilla.redhat.com/show_bug.cgi?id=447489
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Tested-by: Luya Tshimbalanga <luya@fedoraproject.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Register_xenstore_notifier should guarantee that the caller gets
notified even if xenstore is already up.
Therefore we revert "do not notify callers from
register_xenstore_notifier" and set xenstored_read at the right time for
PV on HVM guests too.
In fact in case of PV on HVM guests xenstored is ready only after the
platform pci driver has completed the initialization, so do not set
xenstored_ready before the call to xenbus_probe().
This patch fixes a shutdown_event watcher registration bug that causes
"xm shutdown" not to work properly.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Jeremy Fitzhardinge <jeremy@goop.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
regulator: max8649 - fix setting extclk_freq
regulator: fix typo in current units
regulator: fix device_register() error handling
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging:
hwmon: f71882fg: use a muxed resource lock for the Super I/O port
|
|
* 'merge-spi' of git://git.secretlab.ca/git/linux-2.6:
of/spi: Fix OF-style driver binding of spi devices
spi: spi-gpio.c tests SPI_MASTER_NO_RX bit twice, but not SPI_MASTER_NO_TX
spi/mpc8xxx: fix buffer overrun on large transfers
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
vlan: dont drop packets from unknown vlans in promiscuous mode
Phonet: Correct header retrieval after pskb_may_pull
um: Proper Fix for f25c80a4: remove duplicate structure field initialization
ip_gre: Fix dependencies wrt. ipv6.
net-2.6: SYN retransmits: Add new parameter to retransmits_timed_out()
iwl3945: queue the right work if the scan needs to be aborted
mac80211: fix use-after-free
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel:
drm/i915: Rephrase pwrite bounds checking to avoid any potential overflow
drm/i915: Sanity check pread/pwrite
drm/i915: Use pipe state to tell when pipe is off
drm/i915: vblank status not valid while training display port
drivers/gpu/drm/i915/i915_gem.c: Add missing error handling code
drm/i915: Fix refleak during eviction.
drm/i915: fix GMCH power reporting
|
|
Since 'select' ignores dependencies, drivers that select INET_LRO must
depend on INET. This fixes the broken configuration reported in
<http://article.gmane.org/gmane.linux.kernel/825646>.
Reported-by: Subrata Modak <subrata@linux.vnet.ibm.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
... and do the same for pread.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
|
|
Move the access control up from the fast paths, which are no longer
universally taken first, up into the caller. This then duplicates some
sanity checking along the slow paths, but is much simpler.
Tracked as CVE-2010-2962.
Reported-by: Kees Cook <kees@ubuntu.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
|
|
Sleep while acquiring a resource lock on the Super I/O port. This should
prevent collisions from causing the hardware probe to fail with -EBUSY.
Signed-off-by: Giel van Schijndel <me@mortis.eu>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Instead of waiting for the display line value to settle, we can simply
wait for the pipe configuration register 'state' bit to turn off.
Contrarywise, disabling the plane will not cause the display line
value to stop changing, so instead we wait for the vblank interrupt
bit to get set. And, we only do this when we're not about to wait for
the pipe to turn off.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
While the display port is in training mode, vblank interrupts don't
occur. Because we have to wait for the display port output to turn on
before starting the training sequence, enable the output in 'normal'
mode so that we can tell when a vblank has occurred, then start the
training sequence.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
This patch adds the OF hook to the spi core so that devices
can automatically be registered based on device tree data. This fixes
a problem with spi devices not binding to drivers after the cleanup of
the spi & i2c binding code.
Signed-off-by: Sinan Akman <sinan@writeme.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
The SPI_MASTER_NO_TX bit (can't do buffer write) wasn't tested. This
code was introduced in commit 3c8e1a84 (spi/spi-gpio: add support for
controllers without MISO or MOSI pin). This patch fixes a bug in
choosing which transfer ops to use.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Extend the error handling code with operations found in other nearby error
handling code
A simplified version of the sematic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
@r@
statement S1,S2,S3;
constant C1,C2,C3;
@@
*if (...)
{... S1 return -C1;}
...
*if (...)
{... when != S1
return -C2;}
...
*if (...)
{... S1 return -C3;}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
|
|
The SYNC bits are BIT6 and BIT7 of MAX8649_SYNC register.
pdata->extclk_freq could be [0|1|2].
(MAX8649_EXTCLK_26MHZ|MAX8649_EXTCLK_13MHZ|MAX8649_EXTCLK_19MHZ)
It requires to left shift 6 bits to properly set extclk_freq.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
This patch fixes a typo that incorrectly reports mA numbers as uA.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
If device_register() fails then call put_device().
See comment to device_register.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
vmwgfx: Fix fb VRAM pinning failure due to fragmentation
vmwgfx: Remove initialisation of dev::devname
vmwgfx: Enable use of the vblank system
vmwgfx: vt-switch (master drop) fixes
drm/vmwgfx: Fix breakage introduced by commit "drm: block userspace under allocating buffer and having drivers overwrite it (v2)"
drm: Hold the mutex when dropping the last GEM reference (v2)
drm/gem: handlecount isn't really a kref so don't make it one.
drm: i810/i830: fix locked ioctl variant
drm/radeon/kms: add quirk for MSI K9A2GM motherboard
drm/radeon/kms: fix potential segfault in r600_ioctl_wait_idle
drm: Prune GEM vma entries
drm/radeon/kms: fix up encoder info messages for DFP6
drm/radeon: fix PCI ID 5657 to be an RV410
|
|
* 'for-linus/i2c/2636-rc5' of git://git.fluff.org/bjdooks/linux:
i2c-s3c2410: fix calculation of SDA line delay
i2c-davinci: Fix race when setting up for TX
i2c-octeon: Return -ETIMEDOUT in octeon_i2c_wait() on timeout
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: invoke DSDT corruption workaround on all Toshiba Satellite
ACPI, APEI, Fix ERST MOVE_DATA instruction implementation
ACPI: fan: Fix more unbalanced code block
ACPI: acpi_pad: simplify code to avoid false gcc build warning
ACPI, APEI, Fix error path for memory allocation
ACPI, APEI, HEST Fix the unsuitable usage of platform_data
ACPI, APEI, Fix acpi_pre_map() return value
ACPI, APEI, Fix APEI related table size checking
ACPI: Disable Windows Vista compatibility for Toshiba P305D
ACPI: Kconfig: fix typo.
ACPI: add missing __percpu markup in arch/x86/kernel/acpi/cstate.c
ACPI: Fix typos
ACPI video: fix a poor warning message
ACPI: fix build warnings resulting from merge window conflict
ACPI: EC: add Vista incompatibility DMI entry for Toshiba Satellite L355
ACPI: expand Vista blacklist to include SP1 and SP2
ACPI: delete ZEPTO idle=nomwait DMI quirk
ACPI: enable repeated PCIEXP wakeup by clearing PCIEXP_WAKE_STS on resume
PM / ACPI: Blacklist systems known to require acpi_sleep=nonvs
ACPI: Don't report current_now if battery reports in mWh
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-idle-2.6
* 'idle-release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-idle-2.6:
intel_idle: Voluntary leave_mm before entering deeper
acpi_idle: add missing \n to printk
intel_idle: add missing __percpu markup
intel_idle: Change mode 755 => 644
cpuidle: Fix typos
intel_idle: PCI quirk to prevent Lenovo Ideapad s10-3 boot hang
|
|
Array of udimm sysfs attributes was not ended with NULL marker, leading to
dereference of random memory.
EDAC DEBUG: edac_create_mci_instance_attributes: edac_create_mci_instance_attributes() file udimm0
EDAC DEBUG: edac_create_mci_instance_attributes: edac_create_mci_instance_attributes() file udimm1
EDAC DEBUG: edac_create_mci_instance_attributes: edac_create_mci_instance_attributes() file udimm2
BUG: unable to handle kernel NULL pointer dereference at 00000000000001a4
IP: [<ffffffff81330b36>] edac_create_mci_instance_attributes+0x148/0x1f1
Pid: 1, comm: swapper Not tainted 2.6.36-rc3-nv+ #483 P6T SE/System Product Name
RIP: 0010:[<ffffffff81330b36>] [<ffffffff81330b36>] edac_create_mci_instance_attributes+0x148/0x1f1
(...)
Call Trace:
[<ffffffff81330b86>] edac_create_mci_instance_attributes+0x198/0x1f1
[<ffffffff81330c9a>] edac_create_sysfs_mci_device+0xbb/0x2b2
[<ffffffff8132f533>] edac_mc_add_mc+0x46b/0x557
[<ffffffff81428901>] i7core_probe+0xccf/0xec0
RIP [<ffffffff81330b36>] edac_create_mci_instance_attributes+0x148/0x1f1
---[ end trace 20de320855b81d78 ]---
Kernel panic - not syncing: Attempted to kill init!
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Doug Thompson <dougthompson@xmission.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
sparc64 allmodconfig:
drivers/serial/mrst_max3110.c: In function `serial_m3110_startup':
drivers/serial/mrst_max3110.c:470: error: `IRQ_TYPE_EDGE_FALLING' undeclared (first use in this function)
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
alpha allmodconfig:
drivers/serial/mfd.c:144: error: implicit declaration of function 'kzalloc'
drivers/serial/mfd.c:144: warning: assignment makes pointer from integer without a cast
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If the soon-to-be scanout buffer is partly covering the intended
VRAM region, move and pin will fail. In that case, just move it out
to system before attempting to move it in again.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The removed code causes oopses with newer drms on master drop.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This is to avoid accessing uninitialized data during
drm_irq_uninstall and vblank ioctls. At the same time, enable error check from
drm_kms_init which previously appeared to ignore all errors.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
We add an option not to enable fbdev, this option is off (0) by default.
Not enabling fbdev at load time makes it possible to co-operate with
vga16fb and vga text mode when VT switching.
However, if 3D resources are active when VT switching, we're currently
not able to switch over to vga, due to device limitations.
This fixes a bug where we previously lost 3D state during VT switch.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
allocating buffer and having drivers overwrite it (v2)"
The mentioned commit breaks the vmwgfx ioctl argument sanity check.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
In order to be fully threadsafe we need to check that the drm_gem_object
refcount is still 0 after acquiring the mutex in order to call the free
function. Otherwise, we may encounter scenarios like:
Thread A: Thread B:
drm_gem_close
unreference_unlocked
kref_put mutex_lock
... i915_gem_evict
... kref_get -> BUG
... i915_gem_unbind
... kref_put
... i915_gem_object_free
... mutex_unlock
mutex_lock
i915_gem_object_free -> BUG
i915_gem_object_unbind
kfree
mutex_unlock
Note that no driver is currently using the free_unlocked vfunc and it is
scheduled for removal, hasten that process.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30454
Reported-and-Tested-by: Magnus Kessler <Magnus.Kessler@gmx.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Now that we hold onto a reference whilst evicting objects, we need to
be sure that we drop all the references taken -- even on the error
paths.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
Avoid TLB flush IPIs for the cores in deeper c-states by voluntary leave_mm()
before entering into that state. CPUs tend to flush TLB in those c-states
anyways.
acpi_idle does this with C3-type states, but it was not caried over
when intel_idle was introduced. intel_idle can apply it
to C-states in addition to those that ACPI might export as C3...
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
There were lots of places being inconsistent since handle count
looked like a kref but it really wasn't.
Fix this my just making handle count an atomic on the object,
and have it increase the normal object kref.
Now i915/radeon/nouveau drivers can drop the normal reference on
userspace object creation, and have the handle hold it.
This patch fixes a memory leak or corruption on unload, because
the driver had no way of knowing if a handle had been actually
added for this object, and the fbcon object needed to know this
to clean itself up properly.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|