| Age | Commit message (Collapse) | Author |
|---|
|
Correcting the if condition check for printing the warning,
if wakeup script is not updated before updating the sleep script.
Since the flag 'order' is set to '1' while updating the wakeup script
for P1P2, the condition checking for printing the warning should be
if(!order) (ie: print the warning if wakeup script is not updated before
updating the sleep script)
Signed-off-by: Lesly A M <leslyam@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: David Derrick <dderrick@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
WARNING: vmlinux.o(.devinit.text+0x6c4): Section mismatch in reference
from the function device_onkey_init() to the (unknown reference)
.init.data:(unknown)
The function __devinit device_onkey_init() references a (unknown reference)
__initdata (unknown).
If (unknown) is only used by device_onkey_init then annotate (unknown)
with a matching annotation.
It's caused by using __initdata on mfd cell resources. Replace __initdata
with __devinitdata.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Remove the unused variable "u16 val" of wl1273-core.c.
Signed-off-by: Wanlong Gao <wanlong.gao@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The fact that we can't actually raise any interrupts doesn't stop us
setting up the IRQs we're exporting. While this isn't actually going
to do anything it allows us to proceed further through device setup
during board bringup and avoids issues with the MFD core not letting
us suppress the configuration of IRQ resources.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Allow the GPIO mode of WM831x devices to be configured using platform data.
Users may provide a table of GPIO register values in gpio_defaults[]. In
order to allow 0 to be set explicitly out of range values are accepted and
masked off, with a WM831X_GPIO_CONFIGURE define provided to set an out of
range value.
This can be used to configure higher numbered GPIOs or override values set
in OTP for GPIOs configured using OTP.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
With the addition of a platform device mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
With the addition of a platform device mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
With the addition of a platform device mfd_cell pointer, MFD drivers
can go back to passing platform back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.
Cc: Miguel Aguilar <miguel.aguilar@ridgerun.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
With the addition of a platform device mfd_cell pointer, MFD drivers
can go back to passing platform back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
With the addition of a platform device mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
With the addition of a platform device mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.
Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
With the addition of a platform device mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.
Cc: Ira W. Snyder <iws@ovro.caltech.edu>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
With the addition of a platform device mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
With the addition of a platform device mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
With the addition of a device platform mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.
Acked-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
With the addition of the platform device mfd_cell pointer, we can now
cleanly pass the sub device drivers platform data pointers through the
regular device platform_data one, and get rid of mfd_get_data().
Cc: Ian Molton <spyro@f2s.com>
Cc: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Acked-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
With the addition of the platform device mfd_cell pointer, we can now
cleanly pass the sub device drivers platform data pointers through the
regular device platform_data one, and get rid of mfd_get_data().
Cc: Ian Molton <spyro@f2s.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Acked-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
With the addition of a platform device mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.
Cc: Matti Aaltonen <matti.j.aaltonen@nokia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
With the addition of the platform device mfd_cell pointer, we can now
cleanly pass the sub device drivers platform data pointers through the
regular device platform_data one, and get rid of mfd_get_data().
Cc: Matt Reimer <mreimer@vpop.net>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
With the addition of the platform device mfd_cell pointer, we can now
cleanly pass the sub device drivers platform data pointers through the
regular device platform_data one, and get rid of mfd_get_data()
Cc: Ian Molton <spyro@f2s.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
With the addition of a platform device mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the sub drivers
MFD agnostic. This is mostly needed for non MFD aware sub drivers.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
With the addition of a platform device mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the sub drivers
MFD agnostic. This is mostly needed for non MFD aware sub drivers.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Now that we have a way to pass MFD cells down to the sub drivers,
we can gradually get rid of mfd_data by putting the platform pointer
back in place.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This patch provides a shim between the kernel-internal cleancache
API (see Documentation/mm/cleancache.txt) and the Xen Transcendent
Memory ABI (see http://oss.oracle.com/projects/tmem).
Xen tmem provides "hypervisor RAM" as an ephemeral page-oriented
pseudo-RAM store for cleancache pages, shared cleancache pages,
and frontswap pages. Tmem provides enterprise-quality concurrency,
full save/restore and live migration support, compression
and deduplication.
A presentation showing up to 8% faster performance and up to 52%
reduction in sectors read on a kernel compile workload, despite
aggressive in-kernel page reclamation ("self-ballooning") can be
found at:
http://oss.oracle.com/projects/tmem/dist/documentation/presentations/TranscendentMemoryXenSummit2010.pdf
Signed-off-by: Dan Magenheimer <dan.magenheimer@oracle.com>
Reviewed-by: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Rik Van Riel <riel@redhat.com>
Cc: Jan Beulich <JBeulich@novell.com>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Andreas Dilger <adilger@sun.com>
Cc: Ted Ts'o <tytso@mit.edu>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <joel.becker@oracle.com>
Cc: Nitin Gupta <ngupta@vflare.org>
|
|
ST-Ericsson modified ARM PrimeCell PL180 block has not got
an updated corresponding amba-id, althought the IP block has
changed in db8500v2. The change was done to the datactrl register.
Using the overrided subversion ID, account for this.
Signed-off-by: Philippe Langlais <philippe.langlais@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This makes a hardcoded periphid from the platform override any
magic number found in the hardware. This shall henceforth be used
when the information found in the hardware is either missing,
i.e. not encoding the CID with the magic cookie 0xb105f00d, or
incorrect such that the revision number should have been bumped in
hardware, but the silicon designer has failed to do so.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The kernel already prints its build timestamp during boot, no need to
repeat it in random drivers and produce different object files each
time.
Cc: Armin Schindler <mac@melware.de>
Cc: netdev@vger.kernel.org
Signed-off-by: Michal Marek <mmarek@suse.cz>
|
|
Merge irq.c and s390_ext.c into irq.c. That way all external interrupt
related functions are together.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Interrupt sources like pfault, sclp, dasd_diag and virtio all use the
service signal external interrupt subclass mask in control register 0
to enable and disable the corresponding interrupt.
Because no reference counting is implemented each subsystem thinks it
is the only user of subclass and sets and clears the bit like it wants.
This leads to case that unloading the dasd diag module under z/VM
causes both sclp and pfault interrupts to be masked. The result will
be locked up system sooner or later.
Fix this by introducing a new way to set (register) and clear
(unregister) the service signal subclass mask bit in cr0.
Also convert all drivers.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The kernel already prints its build timestamp during boot, no need to
repeat it in random drivers and produce different object files each
time.
Acked-by: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Michal Marek <mmarek@suse.cz>
|
|
Fix this:
drivers/video/mb862xx/mb862xx-i2c.c: In function 'mb862xx_i2c_wait_event':
drivers/video/mb862xx/mb862xx-i2c.c:25: error: implicit declaration of function 'udelay'
caused by commit f8a6b1f44833 ("video: mb862xx: add support for
controller's I2C bus adapter").
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
driver to use dvb-usb-remote.
The remote(s) generates 24 bit NEC codes, lme2510 keymaps redefined.
Other minor fixes
fix le warning.
make sure frontend is detached on firmware change.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Hans Petter Selasky <hselasky@c2i.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Hans Petter Selasky <hselasky@c2i.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Hans Petter Selasky <hselasky@c2i.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (89 commits)
bonding: documentation and code cleanup for resend_igmp
bonding: prevent deadlock on slave store with alb mode (v3)
net: hold rtnl again in dump callbacks
Add Fujitsu 1000base-SX PCI ID to tg3
bnx2x: protect sequence increment with mutex
sch_sfq: fix peek() implementation
isdn: netjet - blacklist Digium TDM400P
via-velocity: don't annotate MAC registers as packed
xen: netfront: hold RTNL when updating features.
sctp: fix memory leak of the ASCONF queue when free asoc
net: make dev_disable_lro use physical device if passed a vlan dev (v2)
net: move is_vlan_dev into public header file (v2)
bug.h: Fix build with CONFIG_PRINTK disabled.
wireless: fix fatal kernel-doc error + warning in mac80211.h
wireless: fix cfg80211.h new kernel-doc warnings
iwlagn: dbg_fixed_rate only used when CONFIG_MAC80211_DEBUGFS enabled
dst: catch uninitialized metrics
be2net: hash key for rss-config cmd not set
bridge: initialize fake_rtable metrics
net: fix __dst_destroy_metrics_generic()
...
Fix up trivial conflicts in drivers/staging/brcm80211/brcmfmac/wl_cfg80211.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (75 commits)
mmc: core: eMMC bus width may not work on all platforms
mmc: sdhci: Auto-CMD23 fixes.
mmc: sdhci: Auto-CMD23 support.
mmc: core: Block CMD23 support for UHS104/SDXC cards.
mmc: sdhci: Implement MMC_CAP_CMD23 for SDHCI.
mmc: core: Use CMD23 for multiblock transfers when we can.
mmc: quirks: Add/remove quirks conditional support.
mmc: Add new VUB300 USB-to-SD/SDIO/MMC driver
mmc: sdhci-pxa: Add quirks for DMA/ADMA to match h/w
mmc: core: duplicated trial with same freq in mmc_rescan_try_freq()
mmc: core: add support for eMMC Dual Data Rate
mmc: core: eMMC signal voltage does not use CMD11
mmc: sdhci-pxa: add platform code for UHS signaling
mmc: sdhci: add hooks for setting UHS in platform specific code
mmc: core: clear MMC_PM_KEEP_POWER flag on resume
mmc: dw_mmc: fixed wrong regulator_enable in suspend/resume
mmc: sdhi: allow powering down controller with no card inserted
mmc: tmio: runtime suspend the controller, where possible
mmc: sdhi: support up to 3 interrupt sources
mmc: sdhi: print physical base address and clock rate
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: New driver for the SMSC EMC6W201
hwmon: (abituguru) Depend on DMI
hwmon: (it87) Use request_muxed_region
hwmon: (sch5627) Trigger Vbat measurements
hwmon: (sch5627) Add sch5627_send_cmd function
i8k: Integrate with the hwmon subsystem
hwmon: (max6650) Properly support the MAX6650
hwmon: (max6650) Drop device detection
Move ACPI power meter driver to hwmon
hwmon: (f71882fg) Add support for F71808A
hwmon: (f71882fg) Split has_beep in fan_has_beep and temp_has_beep
hwmon: (asc7621) Drop duplicate dependency
hwmon: (jc42) Change detection class
hwmon: Add driver for AMD family 15h processor power information
hwmon: (k10temp) Add support for Fam15h (Bulldozer)
hwmon: Use helper functions to set and get driver data
i8k: Avoid lahf in 64-bit code
|
|
devel-stable
|
|
s5p-csis is to be built only on S5P SoC platforms.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Fixes media_build, and presumably certain other upstream kernel build
option combos.
Before:
CC [M] /home/jarod/src/media_build/v4l/kinect.o
/home/jarod/src/media_build/v4l/kinect.c:38:19: error: 'D_ERR' undeclared here (not in a function)
/home/jarod/src/media_build/v4l/kinect.c:38:27: error: 'D_PROBE' undeclared here (not in a function)
/home/jarod/src/media_build/v4l/kinect.c:38:37: error: 'D_CONF' undeclared here (not in a function)
/home/jarod/src/media_build/v4l/kinect.c:38:46: error: 'D_STREAM' undeclared here (not in a function)
/home/jarod/src/media_build/v4l/kinect.c:38:57: error: 'D_FRAM' undeclared here (not in a function)
/home/jarod/src/media_build/v4l/kinect.c:38:66: error: 'D_PACK' undeclared here (not in a function)
/home/jarod/src/media_build/v4l/kinect.c:39:2: error: 'D_USBI' undeclared here (not in a function)
/home/jarod/src/media_build/v4l/kinect.c:39:11: error: 'D_USBO' undeclared here (not in a function)
/home/jarod/src/media_build/v4l/kinect.c:39:20: error: 'D_V4L2' undeclared here (not in a function)
make[3]: *** [/home/jarod/src/media_build/v4l/kinect.o] Error 1
After:
CC [M] /home/jarod/src/media_build/v4l/kinect.o
...
LD [M] /home/jarod/src/media_build/v4l/gspca_kinect.ko
...
profit
Reported-by: Nicolas Will <nico@youplala.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This is a new driver for the Fintek LPC SuperIO CIR function, in the
Fintek F71809 chip. Hardware and datasheets were provided by Fintek, so
thanks go to them for supporting this effort.
This driver started out as a copy of the nuvoton-cir driver, and was
then modified as needed for the Fintek chip. The two share many
similaries, though the buffer handling for the Fintek chip is actually
nearly identical to the mceusb buffer handling, so the parser routine is
almost a drop-in copy of the mceusb buffer parser (a candidate for being
abstracted out into shared code at some point).
This initial code drop *only* supports receive, but the hardware does
support transmit as well. I really haven't even started to look at
what's required, but my guess is that its also pretty similar to mceusb.
Most people are probably only really interested in RX anyway though, so
I think its good to get this out there even with only RX.
(Nb: there are also Fintek-made mceusb receivers, which presumably, this
chip shares CIR hardware with).
This hardware can be found on at least Jetway NC98 boards and derivative
systems, and likely others as well. Functionality was tested with an
NC98 development board, in-kernel decode of RC6 (mce), RC5 (hauppauge)
and NEC-ish (tivo) remotes all successful, as was lirc userspace decode
of the RC6 remote.
CC: Aaron Huang <aaron_huang@fintek.com.tw>
CC: Tom Tsai <tom_tsai@fintek.com.tw>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Unsurprisingly, URBs get submitted and completed a lot in the xHCI
driver. If we have to print 10 lines of debug for every URB submitted
or completed, then that can cause the whole system to stay in the
interrupt handler too long, and can cause Missed Service completion
codes for isochronous transfers.
Cut down the debugging in the URB submission and completion paths:
- Don't squawk about successful transfers, only unsuccessful ones.
- Only print the number of bytes transferred if this was a short
transfer.
- Don't print the endpoint index for successful transfers (will add
more debug to failed transfers to show endpoint index there later).
- Stop printing MMIO writes. This debugging shows up when the endpoint
doorbell is rung a to start a transfer (basically for every URB).
- Don't print out the ring enqueue and dequeue pointers
- Stop printing when we're pointing to a link TRB.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
Stop printing out the event ring dequeue pointer and status register in
the operational register set. The host will report an OK status 99% of
the time the interrupt handler is called, and usually when it's really
hosed, a host controller won't even call the interrupt handler. So the
line is really useless.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
The video devices associated to USB streaming terminals must be
connected to their associated terminal's media entity instead of being
standalone entities.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Userspace applications can now discover the UVC device topology using
the media controller API.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
As a first step to the media controller integration register a
v4l2_device for each UVC control interface and make the video_device a
child of the v4l2_device.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile: (26 commits)
arch/tile: prefer "tilepro" as the name of the 32-bit architecture
compat: include aio_abi.h for aio_context_t
arch/tile: cleanups for tilegx compat mode
arch/tile: allocate PCI IRQs later in boot
arch/tile: support signal "exception-trace" hook
arch/tile: use better definitions of xchg() and cmpxchg()
include/linux/compat.h: coding-style fixes
tile: add an RTC driver for the Tilera hypervisor
arch/tile: finish enabling support for TILE-Gx 64-bit chip
compat: fixes to allow working with tile arch
arch/tile: update defconfig file to something more useful
tile: do_hardwall_trap: do not play with task->sighand
tile: replace mm->cpu_vm_mask with mm_cpumask()
tile,mn10300: add device parameter to dma_cache_sync()
audit: support the "standard" <asm-generic/unistd.h>
arch/tile: clarify flush_buffer()/finv_buffer() function names
arch/tile: kernel-related cleanups from removing static page size
arch/tile: various header improvements for building drivers
arch/tile: disable GX prefetcher during cache flush
arch/tile: tolerate disabling CONFIG_BLK_DEV_INITRD
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson
* 'for-torvalds' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
mach-ux500: voltage domain regulators for DB8500
cpufreq: make DB8500 cpufreq driver compile
cpufreq: update DB8500 cpufreq driver
mach-ux500: move CPUfreq driver to cpufreq subsystem
mfd: add DB5500 PRCMU driver
mfd: update DB8500 PRCMU driver
mach-ux500: move the DB8500 PRCMU driver to MFD
mach-ux500: make PRCMU base address dynamic
mach-ux500: rename PRCMU driver per SoC
mach-ux500: update ASIC version detection
mach-ux500: update SoC and board IRQ handling
mach-ux500: update the DB5500 register file
mach-ux500: update the DB8500 register file
|
