summaryrefslogtreecommitdiffstats
path: root/drivers
AgeCommit message (Collapse)Author
2010-08-08e100/e1000*/igb*/ixgb*: Add missing read memory barrierJeff Kirsher
Based on patches from Sonny Rao and Milton Miller... Combined the patches to fix up clean_tx_irq and clean_rx_irq. The PowerPC architecture does not require loads to independent bytes to be ordered without adding an explicit barrier. In ixgbe_clean_rx_irq we load the status bit then load the packet data. With packet split disabled if these loads go out of order we get a stale packet, but we will notice the bad sequence numbers and drop it. The problem occurs with packet split enabled where the TCP/IP header and data are in different descriptors. If the reads go out of order we may have data that doesn't match the TCP/IP header. Since we use hardware checksumming this bad data is never verified and it makes it all the way to the application. This bug was found during stress testing and adding this barrier has been shown to fix it. The bug can manifest as a data integrity issue (bad payload data) or as a BUG in skb_pull(). This was a nasty bug to hunt down, if people agree with the fix I think it's a candidate for stable. Previously Submitted to e1000-devel only for ixgbe http://marc.info/?l=e1000-devel&m=126593062701537&w=3 We've now seen this problem hit with other device drivers (e1000e mostly) So I'm resubmitting with fixes for other Intel Device Drivers with similar issues. CC: Milton Miller <miltonm@bga.com> CC: Anton Blanchard <anton@samba.org> CC: Sonny Rao <sonnyrao@us.ibm.com> CC: stable <stable@kernel.org> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-08ixgbe: fix build error with FCOE_CONFIG without DCB_CONFIGJohn Fastabend
Building ixgbe without DCB_CONFIG and FCOE_CONFIG will cause a build error. This resolves the build error by wrapping the fcoe.up in CONFIG_IXGBE_DCB ifdefs. Also frames were being priority VLAN tagged even without DCB enabled. This fixes this so that 8021Q priority tags are only added with DCB actually enabled. Reported-by: divya <dipraksh@linux.vnet.ibm.com> Reported-by: Jon Mason <jon.mason@exar.com> Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-07netxen: protect tx timeout recovery by rtnl lockAmit Kumar Salecha
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-07isdn: gigaset: use after freeDan Carpenter
I moved the kfree(cb) below the dereferences. Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-07isdn: gigaset: add missing unlockDan Carpenter
We should unlock here. This is the only place where we return from the function with the lock held. The caller isn't expecting it. Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-07solos-pci: Fix race condition in tasklet RX handlingDavid Woodhouse
We were seeing faults in the solos-pci receive tasklet when packets arrived for a VCC which was currently being closed: [18842.727906] EIP: [<e082f490>] br2684_push+0x19/0x234 [br2684] SS:ESP 0068:dfb89d14 [18845.090712] [<c13ecff3>] ? do_page_fault+0x0/0x2e1 [18845.120042] [<e082f490>] ? br2684_push+0x19/0x234 [br2684] [18845.153530] [<e084fa13>] solos_bh+0x28b/0x7c8 [solos_pci] [18845.186488] [<e084f711>] ? solos_irq+0x2d/0x51 [solos_pci] [18845.219960] [<c100387b>] ? handle_irq+0x3b/0x48 [18845.247732] [<c10265cb>] ? irq_exit+0x34/0x57 [18845.274437] [<c1025720>] tasklet_action+0x42/0x69 [18845.303247] [<c102643f>] __do_softirq+0x8e/0x129 [18845.331540] [<c10264ff>] do_softirq+0x25/0x2a [18845.358274] [<c102664c>] _local_bh_enable_ip+0x5e/0x6a [18845.389677] [<c102666d>] local_bh_enable+0xb/0xe [18845.417944] [<e08490a8>] ppp_unregister_channel+0x32/0xbb [ppp_generic] [18845.458193] [<e08731ad>] pppox_unbind_sock+0x18/0x1f [pppox] This patch uses an RCU-inspired approach to fix it. In the RX tasklet's find_vcc() function we first refuse to use a VCC which already has the ATM_VF_READY bit cleared. And in the VCC close function, we synchronise with the tasklet to ensure that it can't still be using the VCC before we continue and allow the VCC to be destroyed. Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Tested-by: Nathan Williams <nathan@traverse.com.au> Cc: stable@kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-06Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
2010-08-06iwlwifi: fix locking assertionsJohannes Berg
spin_is_locked() can return zero on some (UP?) configurations because locks don't exist, and that causes an endless amount of warnings. Use lockdep_assert_held() instead, which has two advantages: 1) it verifies the current task is holding the lock or mutex 2) it compiles away completely when lockdep is not enabled Cc: stable@kernel.org [2.6.34+, maybe only parts of patch] Reported-by: Thomas Meyer <thomas@m3y3r.de> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-06iwlwifi: fix TX tracerJohannes Berg
The TX tracing code copies with the wrong length, which will typically copy too little data. Fix this by using the correct length variable. Cc: stable@kernel.org [2.6.32+] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-05isdn: fix information leakDan Carpenter
The main motivation of this patch changing strcpy() to strlcpy(). We strcpy() to copy a 48 byte buffers into a 49 byte buffers. So at best the last byte has leaked information, or maybe there is an overflow? Anyway, this patch closes the information leaks by zeroing the memory and the calls to strlcpy() prevent overflows. Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-05usbnet: remove noisy and hardly useful printkChristian Samsel
With turned on hspa modem (Dell 5530 internal card) and activated usb auto suspend, my system gets up 100 "usbnet_resume has delayed data" per minute. I didnt noticed any pathological behaviour, so just drop this message. if any objections, please at least change it to _DEBUG. Signed-off-by: Christian Samsel <christian.samsel@rwth-aachen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-05rtl8180: avoid potential NULL deref in rtl8180_beacon_workJohn W. Linville
ieee80211_beacon_get can return NULL... Signed-off-by: John W. Linville <linville@tuxdriver.com> Cc: stable@kernel.org
2010-08-05libertas: scan before assocation if no BSSID was givenDan Williams
Fix this leftover TODO from the cfg80211 conversion by doing a scan if cfg80211 didn't pass in the BSSID for us. Since the scan code uses so much of the cfg80211_scan_request structure to build up the firmware command, we just fake one when the scan request is triggered internally. But we need to make sure that internal 'fake' cfg82011 scan request does not get back to cfg82011 via cfg80211_scan_done(). Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-05libertas: fix association with some APs by using extended ratesDan Williams
Some APs get pissy if you don't send the firmware the extended rates in the association request's rates TLV. Found this on a Linksys WRT54G v2; it denies association with status code 18 unless you add the extended rates too. The old driver did this, but it got lost in the cfg80211 conversion. Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-05libertas: get the right # of scanned BSSesDan Williams
Let's actually check the right field in the command response; and if there aren't any reported BSSes, exit early with success. Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04virtio_net: implements ethtool_ops.get_drvinfoRusty Russell
I often use "ethtool -i" command to check what driver controls the ehternet device. But because current virtio_net driver doesn't support "ethtool -i", it becomes the following: # ethtool -i eth3 Cannot get driver information: Operation not supported This patch simply adds the "ethtool -i" support. The following is the result when using the virtio_net driver with my patch applied to. # ethtool -i eth3 driver: virtio_net version: N/A firmware-version: N/A bus-info: virtio0 Personally, "-i" is one of the most frequently-used option, and most network drivers support "ethtool -i", so I think virtio_net also should do. Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (use ARRAY_SIZE) Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-04ppp: make channel_ops conststephen hemminger
The PPP channel ops structure should be const. Cleanup the declarations to use standard C99 format. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-04drivers/net/enic: Use %pUB to format a UUIDJoe Perches
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-04davinci_emac: Fix use after free in davinci_emac_removeStefan Weil
free_netdev finally calls kfree which makes the contents of ndev and priv (private data contained in ndev) invalid. So iounmap should be called before free_netdev. Cc: David S. Miller <davem@davemloft.net> Cc: Chaithrika U S <chaithrika@ti.com> Cc: Sriramakrishnan <srk@ti.com> Cc: Kevin Hilman <khilman@deeprootsystems.com> Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Stefan Weil <weil@mail.berlios.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-04via-velocity: do not use PCI resources before pci_enable_device()Kulikov Vasiliy
IRQ and resource[] may not have correct values until after PCI hotplug setup occurs at pci_enable_device() time. The semantic match that finds this problem is as follows: // <smpl> @@ identifier x; identifier request ~= "pci_request.*|pci_resource.*"; @@ ( * x->irq | * x->resource | * request(x, ...) ) ... *pci_enable_device(x) // </smpl> Signed-off-by: Kulikov Vasiliy <segooon@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-04cxgb4vf: do not use PCI resources before pci_enable_device()Kulikov Vasiliy
IRQ and resource[] may not have correct values until after PCI hotplug setup occurs at pci_enable_device() time. The semantic match that finds this problem is as follows: // <smpl> @@ identifier x; identifier request ~= "pci_request.*|pci_resource.*"; @@ ( * x->irq | * x->resource | * request(x, ...) ) ... *pci_enable_device(x) // </smpl> Signed-off-by: Kulikov Vasiliy <segooon@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-04cxgb3: do not use PCI resources before pci_enable_device()Kulikov Vasiliy
IRQ and resource[] may not have correct values until after PCI hotplug setup occurs at pci_enable_device() time. The semantic match that finds this problem is as follows: // <smpl> @@ identifier x; identifier request ~= "pci_request.*|pci_resource.*"; @@ ( * x->irq | * x->resource | * request(x, ...) ) ... *pci_enable_device(x) // </smpl> Signed-off-by: Kulikov Vasiliy <segooon@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-04Merge branch 'for-next' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial * 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (48 commits) Documentation: update broken web addresses. fix comment typo "choosed" -> "chosen" hostap:hostap_hw.c Fix typo in comment Fix spelling contorller -> controller in comments Kconfig.debug: FAIL_IO_TIMEOUT: typo Faul -> Fault fs/Kconfig: Fix typo Userpace -> Userspace Removing dead MACH_U300_BS26 drivers/infiniband: Remove unnecessary casts of private_data fs/ocfs2: Remove unnecessary casts of private_data libfc: use ARRAY_SIZE scsi: bfa: use ARRAY_SIZE drm: i915: use ARRAY_SIZE drm: drm_edid: use ARRAY_SIZE synclink: use ARRAY_SIZE block: cciss: use ARRAY_SIZE comment typo fixes: charater => character fix comment typos concerning "challenge" arm: plat-spear: fix typo in kerneldoc reiserfs: typo comment fix update email address ...
2010-08-04Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (30 commits) Revert "HID: add support for the Wacom Intuos 4 wireless" HID: fix up Kconfig entry for ACRUX driver HID: add ACRUX game controller force feedback support HID: Force input registration for "VEC footpedal" HID: add HID_QUIRK_HIDINPUT_FORCE HID: hid-input.c: indentation fixes HID: hiddev: use usb_find_interface, get rid of BKL HID: ignore digitizer usage Undefined (0x00) HID: Add support for Conceptronic CLLRCMCE HID: hid-ids.h: Whitespace fixup, align using TABs HID: picolcd: implement refcounting of framebuffer HID: picolcd: do not reallocate memory on depth change HID: picolcd: Add minimal palette required by fbcon on 8bpp HID: magicmouse: Correct parsing of large X and Y motions. HID: magicmouse: report last touch up HID: picolcd: fix deferred_io init/cleanup to fb ordering HID: hid-ids.h: keep vendor ids in alphabetical order HID: add proper support for Elecom BM084 bluetooth mouse HID: magicmouse: enable horizontal scrolling HID: magicmouse: add param for scroll speed ...
2010-08-04Merge git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (39 commits) random: Reorder struct entropy_store to remove padding on 64bits padata: update API documentation padata: Remove padata_get_cpumask crypto: pcrypt - Update pcrypt cpumask according to the padata cpumask notifier crypto: pcrypt - Rename pcrypt_instance padata: Pass the padata cpumasks to the cpumask_change_notifier chain padata: Rearrange set_cpumask functions padata: Rename padata_alloc functions crypto: pcrypt - Dont calulate a callback cpu on empty callback cpumask padata: Check for valid cpumasks padata: Allocate cpumask dependend recources in any case padata: Fix cpu index counting crypto: geode_aes - Convert pci_table entries to PCI_VDEVICE (if PCI_ANY_ID is used) pcrypt: Added sysfs interface to pcrypt padata: Added sysfs primitives to padata subsystem padata: Make two separate cpumasks padata: update documentation padata: simplify serialization mechanism padata: make padata_do_parallel to return zero on success padata: Handle empty padata cpumasks ...
2010-08-04Merge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (276 commits) [SCSI] zfcp: Trigger logging in the FCP channel on qdio error conditions [SCSI] zfcp: Introduce experimental support for DIF/DIX [SCSI] zfcp: Enable data division support for FCP devices [SCSI] zfcp: Prevent access on uninitialized memory. [SCSI] zfcp: Post events through FC transport class [SCSI] zfcp: Cleanup QDIO attachment and improve processing. [SCSI] zfcp: Cleanup function parameters for sbal value. [SCSI] zfcp: Use correct width for timer_interval field [SCSI] zfcp: Remove SCSI device when removing unit [SCSI] zfcp: Use memdup_user and kstrdup [SCSI] zfcp: Fix retry after failed "open port" erp action [SCSI] zfcp: Fail erp after timeout [SCSI] zfcp: Use forced_reopen in terminate_rport_io callback [SCSI] zfcp: Register SCSI devices after successful fc_remote_port_add [SCSI] zfcp: Do not try "forced close" when port is already closed [SCSI] zfcp: Do not unblock rport from REOPEN_PORT_FORCED [SCSI] sd: add support for runtime PM [SCSI] implement runtime Power Management [SCSI] convert to the new PM framework [SCSI] Unify SAM_ and SAM_STAT_ macros ...
2010-08-04iwlagn: Improve aggregation failure error messagesAndy Lutomirski
82ca9341763107615a15da6e59b9535d49eb91c3 added scary looking but harmless error messages. Make them clearer and make the actual failure message show up with the same severity as the harmless one. Signed-off-by: Andy Lutomirski <luto@mit.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04rt2x00: do not use PCI resources before pci_enable_device()Kulikov Vasiliy
IRQ and resource[] may not have correct values until after PCI hotplug setup occurs at pci_enable_device() time. The semantic match that finds this problem is as follows: // <smpl> @@ identifier x; identifier request ~= "pci_request.*|pci_resource.*"; @@ ( * x->irq | * x->resource | * request(x, ...) ) ... *pci_enable_device(x) // </smpl> Signed-off-by: Kulikov Vasiliy <segooon@gmail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04wireless: ipw2100: check result of kzalloc()Christoph Fritz
If kzalloc() fails return with -ENOMEM from ipw2100_net_init() which is called by register_netdev. CC: Dan Carpenter <error27@gmail.com> Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04ath9k: fix erased ieee80211_rx_status.mactimeJan Friedrich
ath9k_rx_skb_preprocess nulls rxs and the mactime is never set again - mactime is always 0. This causes problems in IBSS mode. ieee80211_rx_bss_info uses mactime to decide if an IBSS merge is needed. Without this patch the merge is triggered by each beacon received. This can be recognized by the "beacon TSF higher than local TSF - IBSS merge with BSSID" log message accompanying each beacon. This problem was not completely fixed in commit a6d2055b02dde1067075795274672720baadd3ca and is not a stable kernel fix. It is solely intended for wireless-testing. Signed-off-by: Jan Friedrich <jft@dev2day.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04p54pci: Add PCI ID for SMC2802WLarry Finger
The SMC2802W appears to work with p54pci. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Tested-by: David Cozatt <olbrannon@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04ath9k: fix an issue in ath_atx_tid paused flag managementLorenzo Bianconi
I noticed a possible issue in the paused flag management of the ath_atx_tid data structure. In particular, in a noisy environment and under heavy load, I observed that the AGGR session establishment could fail several times consecutively causing values of the paused flag greater than one for this TID (ath_tx_pause_tid is called more than once from ath_tx_aggr_start). Considering that the session for this TID can not be established also after the mac80211 stack calls the ieee80211_agg_tx_operational() since the ath_tx_aggr_resume() lowers the paused flag only by one. This patch also replaces some BUG_ON calls with WARN_ON, as even if these unlikely conditions happen, it's not fatal enough to justify a BUG_ON. Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04ath9k_hw: Fix regulatory CTL index usage for AR9003Luis R. Rodriguez
AR9003 was not relying on the CTL indexes from the EEPROM for capping the max output power. The CTL indexes from the EEPROM provide calibrated limits for output power for each tested and supported frequency. Without this the device operates at a power level which only conforms to the transmit spectrum mask as specified by IEEE Annex I.2.3. The regulatory limit by CRDA is always used but does not provide calibrated values for optimal performance, specially on band edges. Using the calibrated data from the EEPROM ensures the device operates at optimal output power while still ensuring proper regulatory compliance. The device uses the minimum of these tree values, the value from CRDA, the calibrated value from CTL indexex, and the value to conform to the IEEE transmit spectrum mask. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04net: wl12xx: do not use kfree'd memoryKulikov Vasiliy
wl1271_dump() uses cmd after kfree(cmd). Move kfree() just after wl1271_dump(). Signed-off-by: Kulikov Vasiliy <segooon@gmail.com> Acked-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04iwlagn: fix typo in ucode_bt_stats_read debugfsWey-Yi Guy
small typo fix in ucode_bt_stats_read debugfs file Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04iwlwifi: BA scd_flow not match condition detectedWey-Yi Guy
It is a uCode bug which cause the tx queue id not match scd_flow in compressed block ack frame, and it need to be addressed in uCode. Currently, driver will log the information when it happen. Since it is possible happen very often and we do not want to fill the syslog, so don't enable the logging by default. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04iwlwifi: fix compile warningJohannes Berg
When iwlwifi is compiled w/o debug, we get this warning: iwl-agn.c: In function ‘iwlagn_load_firmware’: iwl-agn.c:2014: warning: passing argument 3 of ‘iwl_print_hex_dump’ discards qualifiers from pointer target type iwl-debug.h:73: note: expected ‘void *’ but argument is of type ‘const u8 *’ because the const qualifier is missing in the inline stub. Fix this. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04ath9k_hw: fix a noise floor calibration related race conditionFelix Fietkau
On AR5008-AR9002, other forms of calibration must not be started while the noise floor calibration is running, as this can create invalid readings which were sometimes not even recoverable by any further calibration attempts. This patch also ensures that the result of noise floor measurements are processed faster and also allows the result of the initial calibration on reset to make it into the NF history buffer Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04ath9k_hw: clean up per-channel calibration dataFelix Fietkau
The noise floor history buffer is currently not kept per channel, which can lead to problems when changing channels from a clean channel to a noisy one. Also when switching from HT20 to HT40, the noise floor history buffer is full of measurements, but none of them contain data for the extension channel, which it needs quite a bit of time to recover from. This patch puts all the per-channel calibration data into a single data structure, and gives the the driver control over whether that is used per-channel or even not used for some channels. For ath9k_htc, I decided to keep this per-channel in order to avoid creating regressions. For ath9k, the data is kept only for the operating channel, which saves some space. ath9k_hw takes care of wiping old data when the operating channel or its channel flags change. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04ath9k: prevent calibration during off-channel activityFelix Fietkau
Previously the software scan callback was used to indicate to the hardware, when it was safe to calibrate. This didn't really work properly, because it depends on a specific order of software scan callbacks vs. channel changes. Also, software scans are not the only thing that triggers off-channel activity, so it's better to use the newly added indication from mac80211 for this and not use the software scan callback for anything calibration related. This fixes at least some of the invalid noise floor readings that I've seen in AP mode on AR9160 Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04ath9k_hw: fix analog shift register writes on AR9003Felix Fietkau
Writes to the analog shift registers, which are issues by the initval programming function, require a 100 usec delay (similar to AR9002, but in a different register range). Signed-off-by: Felix Fietkau <nbd@openwrt.org> Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04ath9k: fix a crash in the PA predistortion apply functionFelix Fietkau
When updating the PAPRD table in hardware, PAPRD itself needs to be disabled first, otherwise the hardware can throw a data bus error, which upsets at least some platforms. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04ath9k_hw: fix periodic noise floor calibration on AR9003Felix Fietkau
The periodic noise floor calibration is broken on this chip family, because it keeps triggering a software-filtered noise floor calibration, but never reads the result before uploading the history buffer value to the hardware. Fix this with a call to ath9k_hw_getnf(), just like on AR9002. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04ath9k_hw: clean up and fix initial noise floor calibrationFelix Fietkau
On AR9003 the initial noise floor calibration is currently triggered at the end of the reset without allowing the hardware to update the baseband settings. This could potentially make scans in noisy environments a bit more unreliable, so use the same calibration sequence that is used on AR9002. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04iwlwifi: fix possible recursive locking deadlockJohannes Berg
commit f84b29ec0a1ab767679d3f2428877b65f94bc3ff Author: Johannes Berg <johannes.berg@intel.com> Date: Tue May 18 02:29:13 2010 -0700 iwlwifi: queue user-initiated scan when doing internal scan introduced a potential deadlock because it calls ieee80211_scan_completed() with the priv->mutex held, but mac80211 may call back into iwlwifi which would lead to recursive locking. Move this out from under the mutex. Cc: stable@kernel.org Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1443 commits) phy/marvell: add 88ec048 support igb: Program MDICNFG register prior to PHY init e1000e: correct MAC-PHY interconnect register offset for 82579 hso: Add new product ID can: Add driver for esd CAN-USB/2 device l2tp: fix export of header file for userspace can-raw: Fix skb_orphan_try handling Revert "net: remove zap_completion_queue" net: cleanup inclusion phy/marvell: add 88e1121 interface mode support u32: negative offset fix net: Fix a typo from "dev" to "ndev" igb: Use irq_synchronize per vector when using MSI-X ixgbevf: fix null pointer dereference due to filter being set for VLAN 0 e1000e: Fix irq_synchronize in MSI-X case e1000e: register pm_qos request on hardware activation ip_fragment: fix subtracting PPPOE_SES_HLEN from mtu twice net: Add getsockopt support for TCP thin-streams cxgb4: update driver version cxgb4: add new PCI IDs ... Manually fix up conflicts in: - drivers/net/e1000e/netdev.c: due to pm_qos registration infrastructure changes - drivers/net/phy/marvell.c: conflict between adding 88ec048 support and cleaning up the IDs - drivers/net/wireless/ipw2x00/ipw2100.c: trivial ipw2100_pm_qos_req conflict (registration change vs marking it static)
2010-08-04Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/ibft-2.6 * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/ibft-2.6: ibft: Use IBFT_SIGN instead of open-coding the search string. ibft: convert iscsi_ibft module to iscsi boot lib ibft: separate ibft parsing from sysfs interface ibft: For UEFI machines actually do scan ACPI for iBFT. ibft: Update iBFT handling for v1.03 of the spec.
2010-08-04Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bpLinus Torvalds
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp: amd64_edac: Minor formatting fix amd64_edac: Fix operator precendence error edac, mc: Improve scrub rate handling amd64_edac: Correct scrub rate setting amd64_edac: Fix DCT base address selector amd64_edac: Remove polling mechanism x86, mce: Notify about corrected events too amd64_edac: Remove unneeded defines edac: Remove EDAC_DEBUG_VERBOSE amd64_edac: Sanitize syndrome extraction
2010-08-04Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6 * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6: PM / Runtime: Add runtime PM statistics (v3) PM / Runtime: Make runtime_status attribute not debug-only (v. 2) PM: Do not use dynamically allocated objects in pm_wakeup_event() PM / Suspend: Fix ordering of calls in suspend error paths PM / Hibernate: Fix snapshot error code path PM / Hibernate: Fix hibernation_platform_enter() pm_qos: Get rid of the allocation in pm_qos_add_request() pm_qos: Reimplement using plists plist: Add plist_last PM: Make it possible to avoid races between wakeup and system sleep PNPACPI: Add support for remote wakeup PM: describe kernel policy regarding wakeup defaults (v. 2) PM / Hibernate: Fix typos in comments in kernel/power/swap.c
2010-08-04Merge branch 'next' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq * 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq: [CPUFREQ] Remove pointless printk from p4-clockmod. [CPUFREQ] Fix section mismatch for powernow_cpu_init in powernow-k7.c [CPUFREQ] Fix section mismatch for longhaul_cpu_init. [CPUFREQ] Fix section mismatch for longrun_cpu_init. [CPUFREQ] powernow-k8: Fix misleading variable naming [CPUFREQ] Convert pci_table entries to PCI_VDEVICE (if PCI_ANY_ID is used) [CPUFREQ] arch/x86/kernel/cpu/cpufreq: use for_each_pci_dev() [CPUFREQ] fix brace coding style issue. [CPUFREQ] x86 cpufreq: Make trace_power_frequency cpufreq driver independent [CPUFREQ] acpi-cpufreq: Fix CPU_ANY CPUFREQ_{PRE,POST}CHANGE notification [CPUFREQ] ondemand: don't synchronize sample rate unless multiple cpus present [CPUFREQ] unexport (un)lock_policy_rwsem* functions [CPUFREQ] ondemand: Refactor frequency increase code [CPUFREQ] powernow-k8: On load failure, remind the user to enable support in BIOS setup [CPUFREQ] powernow-k8: Limit Pstate transition latency check [CPUFREQ] Fix PCC driver error path [CPUFREQ] fix double freeing in error path of pcc-cpufreq [CPUFREQ] pcc driver should check for pcch method before calling _OSC [CPUFREQ] fix memory leak in cpufreq_add_dev [CPUFREQ] revert "[CPUFREQ] remove rwsem lock from CPUFREQ_GOV_STOP call (second call site)" Manually fix up non-data merge conflict introduced by new calling conventions for trace_power_start() in commit 6f4f2723d085 ("x86 cpufreq: Make trace_power_frequency cpufreq driver independent"), which didn't update the intel_idle native hardware cpuidle driver.
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2025-01-30 06:04:43 +0000