| Age | Commit message (Collapse) | Author |
|---|
|
Given that srpt_release_channel_work() calls target_wait_for_sess_cmds()
to allow outstanding se_cmd_t->cmd_kref a change to complete, the call
to perform target_sess_cmd_list_set_waiting() needs to happen in
srpt_shutdown_session()
Also, this patch adds an explicit call to srpt_shutdown_session() within
srpt_drain_channel() so that target_sess_cmd_list_set_waiting() will be
called in the cases where TFO->shutdown_session() is not triggered
directly by TCM.
Cc: Joern Engel <joern@logfs.org>
Cc: Roland Dreier <roland@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Switch back to pre commit 1c7b13fe652 list splicing logic for active I/O
shutdown with tcm_qla2xxx + ib_srpt fabrics.
The original commit was done under the incorrect assumption that it's safe to
walk se_sess->sess_cmd_list unprotected in target_wait_for_sess_cmds() after
sess->sess_tearing_down = 1 has been set by target_sess_cmd_list_set_waiting()
during session shutdown.
So instead of adding sess->sess_cmd_lock protection around sess->sess_cmd_list
during target_wait_for_sess_cmds(), switch back to sess->sess_wait_list to
allow wait_for_completion() + TFO->release_cmd() to occur without having to
walk ->sess_cmd_list after the list_splice.
Also add a check to exit if target_sess_cmd_list_set_waiting() has already
been called, and add a WARN_ON to check for any fabric bug where new se_cmds
are added to sess->sess_cmd_list after sess->sess_tearing_down = 1 has already
been set.
Cc: Joern Engel <joern@logfs.org>
Cc: Roland Dreier <roland@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin-control fixes from Linus Walleij:
- Six patches fixing up the suspend/resume and wakeup handling of the
Samsung and Exynos drivers.
- Errorpath fixes for four different drivers. All on the probe()
errorpath.
- Make the debugfs code for pin config take the right mutex.
* tag 'pinctrl-fixes-v3.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: pinconf: take the right mutex
pinctrl: sunxi: fix error return code in sunxi_pinctrl_probe()
pinctrl: exynos: Handle suspend/resume of GPIO EINT registers
pinctrl: samsung: Allow per-bank SoC-specific private data
pinctrl: samsung: Add support for SoC-specific suspend/resume callbacks
pinctrl: Don't override the error code in probe error handling
ARM: EXYNOS: Fix EINT wake-up mask configuration when pinctrl is used
pinctrl: exynos: Add support for set_irq_wake of wake-up EINTs
pinctrl: samsung: fix suspend/resume functionality
|
|
With the addition of a DVO clock, a bug is now evident in the vt8500
clock code:
[ 0.290000] WARNING: at init/main.c:698 do_one_initcall+0x158/0x18c()
[ 0.300000] initcall wm8505fb_driver_init+0x0/0xc returned with disabled int
This is caused by an unbalanced spinlock in vt8500_dclk_set_rate().
Replace the second call to spin_lock_irqsave() with spin_unlock_irqrestore().
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
clock-frequency property from platform data was read but never used.
Apply defined rate when clock is registered.
Signed-off-by: Marek Belisko <marek.belisko@streamunlimited.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
[mturquette@linaro.org: add missing changelog]
Cc: stable@kernel.org
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Rate was incorrectly computed because we read from wrong divider register.
Signed-off-by: Marek Belisko <marek.belisko@streamunlimited.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Cc: stable@kernel.org
|
|
Apparently we should not free page that has not been allocated.
This is b/c alloc_xenballooned_pages will take care of freeing
the page on its own.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/linux-block into for-linus
Jiri writes:
please pull from
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/linux-block.git for-jens
to receive one pktcdvd fix. It fixes a highly theoretical issue with using.
pktcdvd to work with media that'd be larger than 2TB :) But it's a correct.
fix and makes static checkers shut up about improperly cleaning upper.
32bits.
|
|
Currently no driver *) handles the sysreg clock, with an assumption
that this clock is always left in its default state (enabled).
Before commit 6e6aac7590f902d14d90bace3fd499
ARM: EXYNOS: Migrate clock support to common clock framework
the sysreg clock was not even defined and hence wasn't handled
explicitly in the kernel.
To restore the previous behaviour disable masking the sysreg clock
off in the clock core by default.
*) Except the Exynos4x12 FIMC-IS driver, which will be modified
to not touch the sysreg clock.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Fix clk_reg_sysctrl() to set main clock registers of new struct
clk_sysctrl even if the registered clock has no parents.
This fixes an issue where "ulpclk" was registered with all clk->reg_*
fields uninitialized, causing a -EINVAL error from clk_prepare().
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
First Ethernet device has a ".0" appended onto the device name. It
appears that we need this in order to obtain the correct clock.
Without this fix Ethernet does not function on Ux500 devices, which is a
regression.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
[mturquette@linaro.org: improved changelog]
|
|
radeon currently uses a drm function to get the speed capabilities for
the bus, drm_pcie_get_speed_cap_mask. However, this is a non-standard
method of performing this detection and this patch changes it to use
the max_bus_speed attribute.
From: Lucas Kannebley Tavares <lucaskt@linux.vnet.ibm.com>
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This narrows the scope of the apple re-POST hack added in:
drm/radeon: re-POST the asic on Apple hardware when booted via EFI
That patch prevents UVD from working on macs when booted in EFI
mode. The original patch fixed macbook2,1 systems which were
r5xx and hence have no UVD. Limit the hack to those systems to
prevent UVD breakage on newer systems.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=63935
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Matthew Garrett <matthew.garrett@nebula.com>
|
|
Skip checking crtcs in hardware without them. Avoids checking
non-existent hardware.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Newer asics have variable numbers of crtcs. Use that
rather than the asic family to determine which crtcs
to check. This avoids checking non-existent crtcs or
missing crtcs on certain asics.
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Should be 5 rather than 2.
Noticed by sroland and glisse on IRC.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
The chip id for SUMO2 isn't used.
fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=63935
Tested-By: Dave Witbrodt <dawitbro@sbcglobal.net>
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
Static checkers complain about widening the binary "not" operations here
because sectors are u64 and "(pd)->settings.size" is unsigned int.
It unintentionally clears the high 32 bits of the sector. This means
that the driver won't work for devices with over 2TB of space. Since
this is a DVD drive, we're unlikely to reach that limit, but we may as
well silence the warning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
Save the xenstore local status computed in xenbus_init. It can then be used
later to check if xenstored is running in this domain.
Signed-off-by: Aurelien Chartier <aurelien.chartier@citrix.com>
[Changes in v4:
- Change variable name to xen_store_domain_type]
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
If the xenbus frontend is located in a domain running xenstored, the device
resume is hanging because it is happening before the process resume. This
patch adds extra logic to the resume code to check if we are the domain
running xenstored and delay the resume if needed.
Signed-off-by: Aurelien Chartier <aurelien.chartier@citrix.com>
[Changes in v2:
- Instead of bypassing the resume, process it in a workqueue]
[Changes in v3:
- Add a struct work in xenbus_device to avoid dynamic allocation
- Several small code fixes]
[Changes in v4:
- Use a dedicated workqueue]
[Changes in v5:
- Move create_workqueue error handling to xenbus_frontend_dev_resume]
Acked-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
into linux-fbdev/for-3.10-fixes
Pull Tomi fixes for ps3fb and omap2
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Increase the current arbitrary limit for isocronous packet size to a
value large enough to account for USB 3.0 super bandwidth streams,
bMaxBurst (0~15 allowed, 1~16 packets)
bmAttributes (bit 1:0, mult 0~2, 1~3 packets)
so the size max for one USB 3 isocronous transfer is
1024 byte * 16 * 3 = 49152 byte
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Federico Manzan <f.manzan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We currently allow changing the mq flag (IFF_MULTI_QUEUE) for a persistent
device. This will result a mismatch between the number the queues in netdev and
tuntap. This is because we only allocate a 1q netdevice when IFF_MULTI_QUEUE was
not specified, so when we set the IFF_MULTI_QUEUE and try to attach more queues
later, netif_set_real_num_tx_queues() may fail which result a single queue
netdevice with multiple sockets attached.
Solve this by disallowing changing the mq flag for persistent device.
Bug was introduced by commit edfb6a148ce62e5e19354a1dcd9a34e00815c2a1
(tuntap: reduce memory using of queues).
Reported-by: Sriram Narasimhan <sriram.narasimhan@hp.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The control-message timeout is specified in milliseconds and should not
depend on HZ.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The control and bulk-message timeouts are specified in milliseconds and
should not depend on HZ.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The bulk-message timeout is specified in milliseconds and should not
depend on HZ.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The control-message timeout is specified in milliseconds and should not
depend on HZ.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix regression introduced by commit 0eafe4de1a ("USB: serial: mos7840:
add support for MCS7810 devices") which used stack-allocated buffers for
control messages.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The read_mos_reg function is called with stack-allocated buffers, which
must not be used for control messages.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix regression introduced by commit 214916f2e ("USB: visor: reimplement
using generic framework") which broke initialisation of Treo/Kyocera
devices that re-mapped bulk-in endpoints.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The first and second interrupt-in urbs are swapped for some Treo/Kyocera
devices, but the urb context was never updated with the new port.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch reverts commit 3e619d04159be54b3daa0b7036b0ce9e067f4b5d
(USB: EHCI: fix bug in scheduling periodic split transfers). The
commit was valid -- it fixed a real bug -- but the periodic scheduler
in ehci-hcd is in such bad shape (especially the part that handles
split transactions) that fixing one bug is very likely to cause
another to surface. That's what happened in this case; the result was
choppy and noisy playback on certain 24-bit audio devices.
The only real fix will be to rewrite this entire section of code. My
next project...
This fixes https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1136110.
Thanks to Tim Richardson for extra testing and feedback, and to Joseph
Salisbury and Tyson Tan for tracking down the original source of the
problem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Joseph Salisbury <joseph.salisbury@canonical.com>
CC: Tim Richardson <tim@tim-richardson.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus
Sarah writes:
xhci: Misc bug fixes for 3.10.
Hi Greg,
Here's four xHCI bug fixes that should be queued for 3.10.
The first two are generic bug fixes, and have been in my queue for a while
because I've been doing the OPW internship coordination. I suspect you'll be
seeing more pull requests from me now that the intern selection process is
almost over. :)
The last two patches fix a nasty kernel crash on resume from S3 for TI hosts
that have the compliance mode quirk. Tony has confirmed that the patches fix
the issue on the effected systems.
All four patches are marked for stable.
Sarah Sharp
|
|
A third possible PCI ID, as personally observed, and found in the
pci.ids list.
Signed-off-by: George Spelvin <linux@horizon.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
In some circumstances setting a 64-bit DMA mask can fail, as explained
in Documentation/DMA-API-HOWTO.txt. Use the recommended code sequence
to set a 32-bit DMA mask if setting a 64-bit DMA mask fails.
Reported-by: Chayan Biswas <Chayan.Biswas@sandisk.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
|
|
Since highmem PIO URB handling was introduced in:
8e8a551 usb: musb: host: Handle highmem in PIO mode
when a URB is being handled it may happen that the static use_sg flag
was set by a previous URB with buffer in highmem. This leads to error
in handling the present URB.
Fix this by making the use_sg flag URB specific.
Cc: stable <stable@vger.kernel.org> # 3.7+
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
we never allocate a TRB pool for physical endpoints
0 and 1 so trying to free it (a invalid TRB pool pointer)
will lead us in a warning while removing dwc3.ko module.
In order to fix the situation, all we have to do is skip
dwc3_free_trb_pool() for physical endpoints 0 and 1 just
as we while deleting endpoints from the endpoints list.
Cc: stable@vger.kernel.org
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
If the glue layer is removed first (core layer later),
it deletes the phy device first, then the core device.
But at core's removal, it still uses PHY's resources, it may
cause kernel's oops. It is much like the problem
Paul Zimmerman reported at:
http://marc.info/?l=linux-usb&m=136547502011472&w=2.
Besides, it is reasonable the PHY is deleted at last as
the controller is the PHY's user.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
If the glue layer is removed first (core layer later),
it deletes the phy device first, then the core device.
But at core's removal, it still uses PHY's resources, it may
cause kernel's oops. It is much like the problem
Paul Zimmerman reported at:
http://marc.info/?l=linux-usb&m=136547502011472&w=2.
Besides, it is reasonable the PHY is deleted at last as
the controller is the PHY's user.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Accessing the OTP memory on AR9950 causes a data bus
like this:
Data bus error, epc == 801f7774, ra == 801f7774
Oops[#1]:
CPU: 0 PID: 1 Comm: swapper Not tainted 3.10.0-rc3 #592
task: 87c28000 ti: 87c22000 task.ti: 87c22000
$ 0 : 00000000 00000061 deadc0de 00000000
$ 4 : b8115f18 00015f18 00000007 00000004
$ 8 : 00000001 7c7c3c7c 7c7c7c7c 7c7c7c7c
$12 : 7c7c3c7c 80320a68 00000000 7c7c7c3c
$16 : 87cd8010 00015f18 00000007 00000000
$20 : 00000064 00000004 87c23c7c 8035210c
$24 : 00000000 801f3674
$28 : 87c22000 87c23b48 00000001 801f7774
Hi : 00000000
Lo : 00000064
epc : 801f7774 ath9k_hw_wait+0x58/0xb0
Not tainted
ra : 801f7774 ath9k_hw_wait+0x58/0xb0
Status: 1000cc03 KERNEL EXL IE
Cause : 4080801c
PrId : 00019750 (MIPS 74Kc)
Modules linked in:
Process swapper (pid: 1, threadinfo=87c22000, task=87c28000, ts=00000000)
Stack : 0000000f 00000061 00002710 8006240c 00000001 87cd8010 87c23bb0 87cd8010
00000000 00000004 00000003 80210c7c 000000b3 67fa8000 0000032a 000006fe
000003e8 00000002 00000028 87c23bf0 000003ff 80210d24 803e5630 80210e28
00000000 00000007 87cd8010 00007044 00000004 00000061 000003ff 000001ff
87c26000 87cd8010 00000220 87cd8bb8 80210000 8020fcf4 87c22000 87c23c08
...
Call Trace:
[<801f7774>] ath9k_hw_wait+0x58/0xb0
[<80210c7c>] ar9300_otp_read_word+0x80/0xd4
[<80210d24>] ar9300_read_otp+0x54/0xb0
[<8020fcf4>] ar9300_check_eeprom_header+0x1c/0x40
[<80210fe4>] ath9k_hw_ar9300_fill_eeprom+0x118/0x39c
[<80206650>] ath9k_hw_eeprom_init+0x74/0xb4
[<801f96d0>] ath9k_hw_init+0x7ec/0x96c
[<801e65ec>] ath9k_init_device+0x340/0x758
[<801f35d0>] ath_ahb_probe+0x21c/0x2c0
[<801c041c>] driver_probe_device+0xc0/0x1e4
[<801c05ac>] __driver_attach+0x6c/0xa4
[<801bea08>] bus_for_each_dev+0x64/0xa8
[<801bfa40>] bus_add_driver+0xcc/0x24c
[<801c0954>] driver_register+0xbc/0x17c
[<803f8fc0>] ath9k_init+0x5c/0x88
[<800608fc>] do_one_initcall+0xec/0x1a0
[<803e6a68>] kernel_init_freeable+0x13c/0x200
[<80309cdc>] kernel_init+0x1c/0xe4
[<80062450>] ret_from_kernel_thread+0x10/0x18
On the AR9550, the OTP registers are located at
the same address as on the AR9340. Use the correct
values to avoid the error.
Cc: stable@vger.kernel.org # 3.6+
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
For p2p client mode powersave mode should be kept disabled. It is
working but inefficient. In general p2p links do no benefit from this
mode, because these links are setup temporarily to transfer data.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Multi channel support was disabled. This patch will enable it and
configure the P2P GO on the correct frequency when multi channel
is used.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Upon deleting a P2P_CLIENT/GO interface the vif and consequently
the wdev is freed before the net_device is actually being unregistered
but cfg80211 still needs to access the wdev. Using destructor field
to free the net_device and vif.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When registration fails the net device is no longer needed. Free
the net device and remove reference to private data from the
driver.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Pass the struct brcmf_cfg80211_info instance instead of obtaining
through vif itself using vif->wdev. This is needed as the netdev
associated with this vif is already unregistered.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The firmware requires that on p2p setup when net interfaces
are created or updated that they start initially with the same
channel as the channel in use for the current connection
(if any). If none exists take default channel 11.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
ARP offloading should only be used in STA or P2P client mode. It
is currently configured once at init. When being configured for AP
ARP offloading should be turned off and when AP mode is left it can
be turned back on.
Cc: stable@vger.kernel.org
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
|
