| Age | Commit message (Collapse) | Author |
|---|
|
Make macro names shorter thus making code shorter and more clear.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
|
|
Add decoder for FP MCEs.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
|
|
Integrate the single FIROB signature into an expanded table along with
the new BD MCE types.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
|
|
by (almost) reusing the F10h one since the signatures are the same.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
|
|
F15h BD doesn't generate LS MCEs so warn about it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
|
|
MCE bank 2 is redefined from a BU to a CU (Combined Unit) bank on F15h.
Add a decoder function for CU MCEs.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
|
|
Add support for decoding F15h IC MCEs.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
|
|
Add a decoder for F15h DC MCEs to support the new types of DC MCEs
introduced by the BD microarchitecture.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
|
|
F15h enlarges the extended error code of an MCE to a 5-bit field
(MCi_STATUS[20:16]). Add a mask variable which default 0xf is overridden
on F15h.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
ipv4/route.c: respect prefsrc for local routes
bridge: stp: ensure mac header is set
bridge: fix br_multicast_ipv6_rcv for paged skbs
atl1: fix oops when changing tx/rx ring params
drivers/atm/atmtcp.c: add missing atm_dev_put
starfire: Fix dma_addr_t size test for MIPS
tg3: fix return value check in tg3_read_vpd()
Broadcom CNIC core network driver: fix mem leak on allocation failures in cnic_alloc_uio_rings()
ISDN, Gigaset: Fix memory leak in do_disconnect_req()
CAN: Use inode instead of kernel address for /proc file
skfp: testing the wrong variable in skfp_driver_init()
ppp: allow disabling multilink protocol ID compression
ehea: Avoid changing vlan flags
ueagle-atm: fix PHY signal initialization race
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] em28xx: radio_fops should also use unlocked_ioctl
[media] wm8775: Revert changeset fcb9757333 to avoid a regression
[media] cx25840: Prevent device probe failure due to volume control ERANGE error
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
dmaengine: provide dummy functions for DMA_ENGINE=n
mv_xor: fix race in tasklet function
|
|
Commit 3f5a2a713aad28480d86b0add00c68484b54febc zeroes out the statistics
message block (SMB) and coalescing message block (CMB) when adapter ring
resources are freed. This is desirable behavior, but, as a side effect,
the commit leads to an oops when atl1_set_ringparam() attempts to alter
the number of rx or tx elements in the ring buffer (by using ethtool
-G, for example). We don't want SMB or CMB to change during this
operation.
Modify atl1_set_ringparam() to preserve SMB and CMB when changing ring
parameters.
Cc: stable@kernel.org
Signed-off-by: Jay Cliburn <jcliburn@gmail.com>
Reported-by: Tõnu Raitviir <jussuf@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
em28xx uses core assisted locking, so it shouldn't use .ioctl.
The .ioctl callback was replaced by .unlocked_ioctl for video nodes,
but not for radio nodes. This is now corrected.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
It seems that cx88 and ivtv use wm8775 on some different modes. The
patch that added support for a board with wm8775 broke ivtv boards with
this device. As we're too close to release 2.6.37, let's just revert
it.
Reported-by: Andy Walls <awalls@md.metrocast.net>
Reported-by: Eric Sharkey <eric@lisaneric.org>
Reported-by: Auric <auric@aanet.com.au>
Reported by: David Gesswein <djg@pdp8online.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This patch fixes a regression that crept into 2.6.36.
The volume control scale in the cx25840 driver has an unusual mapping
from register values to v4l2 volume control values. Enforce the mapping
limits, so that the default volume control setting does not fall out of
bounds to prevent the cx25840 module device probe from failing.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
use mv_xor_slot_cleanup() instead of __mv_xor_slot_cleanup() as the former function
aquires the spin lock that needed to protect the drivers data.
Cc: <stable@kernel.org>
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
The owner field was removed from struct attribute in
6fd69dc578fa0b1bbc3aad70ae3af9a137211707, so don't assign it anymore.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
The earlier call to atm_dev_lookup increases the reference count of dev,
so decrease it on the way out.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x, E;
constant C;
@@
x = atm_dev_lookup(...);
... when != false x != NULL
when != true x == NULL
when != \(E = x\|x = E\)
when != atm_dev_put(dev);
*return -C;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 56543af "starfire: use BUILD_BUG_ON for netdrv_addr_t" revealed
that the preprocessor condition used to find the size of dma_addr_t
yielded the wrong result for some architectures and configurations.
This was kluged for 64-bit PowerPC in commit 3e502e6 by adding yet
another case to the condition. However, 64-bit MIPS configurations
are not detected reliably either.
This should be fixed by using CONFIG_ARCH_DMA_ADDR_T_64BIT, but that
isn't yet defined everywhere it should be.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Besides -ETIMEDOUT and -EINTR, pci_read_vpd may return other error
values like -ENODEV or -EINVAL which are ignored due to the buggy
check, but the data are not read from VPD anyway and this is checked
subsequently with at most 3 needless loop iterations. This does not
show up as a runtime bug.
CC: Matt Carlson <mcarlson@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
cnic_alloc_uio_rings()
We are leaking memory in drivers/net/cnic.c::cnic_alloc_uio_rings() if
either of the calls to dma_alloc_coherent() fail. This patch fixes it by
freeing both the memory allocated with kzalloc() and memory allocated with
previous calls to dma_alloc_coherent() when there's a failure.
Thanks to Joe Perches <joe@perches.com> for suggesting a better
implementation than my initial version.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hi,
In drivers/isdn/gigaset/capi.c::do_disconnect_req() we will leak the
memory allocated (with kmalloc) to 'b3cmsg' if the call to alloc_skb()
fails.
...
b3cmsg = kmalloc(sizeof(*b3cmsg), GFP_KERNEL);
allocation here ------^
if (!b3cmsg) {
dev_err(cs->dev, "%s: out of memory\n", __func__);
send_conf(iif, ap, skb, CAPI_MSGOSRESOURCEERR);
return;
}
capi_cmsg_header(b3cmsg, ap->id, CAPI_DISCONNECT_B3, CAPI_IND,
ap->nextMessageNumber++,
cmsg->adr.adrPLCI | (1 << 16));
b3cmsg->Reason_B3 = CapiProtocolErrorLayer1;
b3skb = alloc_skb(CAPI_DISCONNECT_B3_IND_BASELEN, GFP_KERNEL);
if (b3skb == NULL) {
dev_err(cs->dev, "%s: out of memory\n", __func__);
send_conf(iif, ap, skb, CAPI_MSGOSRESOURCEERR);
return;
leak here ------^
...
This leak is easily fixed by just kfree()'ing the memory allocated to
'b3cmsg' right before we return. The following patch does that.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel:
drm/i915/dvo: Report LVDS attached to ch701x as connected
Revert "drm/i915/bios: Reverse order of 100/120 Mhz SSC clocks"
drm/i915: Verify Ironlake eDP presence on DP_A using the capability fuse
drm/i915, intel_ips: When i915 loads after IPS, make IPS relink to i915.
drm/i915/sdvo: Add hdmi connector properties after initing the connector
drm/i915: Set the required VFMUNIT clock gating disable on Ironlake.
|
|
This reverts commit 7e24cce38a99f373450db67bf576fe73e8168d66 because it
was never appropriate for mainline.
Do not check for init flag before starting I/O - zram module is unusable
without this fix.
The oops mentioned in the reverted commit message was actually a problem
only with the zram version as present in project's own repository where
we allocate struct zram_stats_cpu upon device initialization. OTOH, In
mainline/staging version of zram, we allocate struct stats upfront, so
this oops cannot happen in mainline version.
Checking for init_done flag in zram_make_request() results in a *no-op*
for any I/O operation since we simply always return success. This flag
is actually set when the first write occurs on a zram disk which
triggers its initialization.
Bug report: https://bugzilla.kernel.org/show_bug.cgi?id=25722
Reported-by: Dennis Jansen <dennis.jansen@web.de>
Signed-off-by: Nitin Gupta <ngupta@vflare.org>
Cc: Anton Blanchard <anton@samba.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
As we have already detected something attached to the chip during
initialisation, always report the LVDS connector status as connected
during probing.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
As I feared, whilst this fixed the clocks for the Lenovo U160, it broke
many other machines. So lets reverts commit 448f53a1ede54eb854d036abf
and search for the real bug.
Reported-and-tested-by: Travis Hume <travis@computoring.org> [et al]
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=25842
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=32698
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
After grabbing a msg from the msgq, the mcfqspi_work function calls
list_del_init on the mcfqspi->msgq which unintentionally deletes the rest
of the list before it can be processed. If qspi call was made using
spi_sync, this can result in a process hang.
Signed-off-by: Jate Sujjavanich <jsujjavanich@syntech-fuelmaster.com>
Acked-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
When SPI wake up from OFF mode, CS is in the wrong state: force it to the
inactive state.
During the system life, I monitored the CS behavior using a oscilloscope.
I also activated debug in omap2_mcspi, so I saw when driver disable the clocks
and restore context when device is not used.Each time the CS was in the correct
state. It was only when system was put suspend to ram with off-mode activated
that on resume the CS was in wrong state( ie activated).
Changelog:
* Change from v1 to v2:
- Rebase on linus/master (after 2.6.37-rc1)
- Do some clean-up and fix indentation on both patches
- Add more explanations for patch 2
* Change from v2 to v3:
- Use directly resume function of spi_master instead of using function
- from spi_device as Grant Likely pointed it out.
- Force this transition explicitly for each CS used by a device.
* Change from v3 to v4:
- Patch clean-up according to Kevin Hilman and checkpatch.
- Now force CS to be in inactive state only if it was inactive when it was
suspended.
* Change from v4 to v5:
- Rebase on linus/master (after 2.6.37-rc3)
- Collapse some lines as pointed by Grant Likely
- Fix a spelling
* Change from v5 to v6:
- Rebase on linus/master (after 2.6.37-rc7)
- Use CONFIG_SUSPEND instead of CONFIG_PM
- Didn't use legacy PM methods anymore. Instead, add a struct dev_pm_ops and
add the resume method there.
- Fix multi-line comment style
* Change from v6 to v7:
- Rebase on linus/master (after 2.6.37-rc8)
- Drop an extra line
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
The intent here was to test if the allocation failed but we tested
"SharedMemSize" instead of "SharedMemAddr" by mistake.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Linux would not connect to other router running old version Cisco IOS (12.0).
This is most likely a bug in that version of IOS, since it is fixed
in later versions. As a workaround this patch allows a module parameter
to be set to disable compressing the protocol ID.
See: https://bugzilla.vyatta.com/show_bug.cgi?id=3979
RFC 1990 allows an implementation to formulate MP fragments as if protocol
compression had been negotiated. This allows us to always send compressed
protocol IDs. But some implementations don't accept MP fragments with
compressed protocol IDs. This parameter allows us to interoperate with
them. The default value of the configurable parameter is the same as the
current behavior: protocol compression is enabled. If protocol compression
is disabled we will not send compressed protocol IDs.
This is based on an earlier patch by Bob Gilligan (using a sysctl).
Module parameter is writable to allow for enabling even if ppp
is already loaded for other uses.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch avoids disabling the vlan flags using ethtool.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A race exists when initializing ueagle-atm devices where the generic atm
device may not yet be created before the driver attempts to initialize
it's PHY signal state, which checks whether the atm device has been
created or not. This often causes the sysfs 'carrier' attribute to be
'1' even though no signal has actually been found.
uea_probe
usbatm_usb_probe
driver->bind (uea_bind)
uea_boot
kthread_run(uea_kthread) uea_kthread
usbatm_atm_init uea_start_reset
atm_dev_register UPDATE_ATM_SIGNAL
UPDATE_ATM_SIGNAL checks whether the ATM device has been created and if
not, will not update the PHY signal state. Because of the race that
does not always happen in time, and the PHY signal state remains
ATM_PHY_SIG_FOUND even though no signal exists.
To fix the race, just create the kthread during initialization, and only
after initialization is complete, start the thread that reboots the
device and initializes PHY state.
[ 3030.490931] uea_probe: calling usbatm_usb_probe
[ 3030.490946] ueagle-atm 8-2:1.0: usbatm_usb_probe: trying driver ueagle-atm with vendor=1110, product=9031, ifnum 0
[ 3030.493691] uea_bind: setting usbatm
[ 3030.496932] usb 8-2: [ueagle-atm] using iso mode
[ 3030.497283] ueagle-atm 8-2:1.0: usbatm_usb_probe: using 3021 byte buffer for rx channel 0xffff880125953508
<kthread already started before usbatm_usb_probe() has returned>
[ 3030.497292] usb 8-2: [ueagle-atm] (re)booting started
<UPDATE_ATM_SIGNAL checks whether ATM device has been created yet before setting PHY state>
[ 3030.497298] uea_start_reset: atm dev (null)
<and since it hasn't been created yet PHY state is not set>
[ 3030.497306] ueagle-atm 8-2:1.0: usbatm_usb_probe: using 3392 byte buffer for tx channel 0xffff8801259535b8
[ 3030.497374] usbatm_usb_probe: about to init
[ 3030.497379] usbatm_usb_probe: calling usbatm_atm_init
<atm device finally gets created>
[ 3030.497384] usbatm_atm_init: creating atm device!
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI hotplug: Fix unexpected driver unregister in pciehp_acpi.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] v4l: soc-camera: fix multiple simultaneous user case
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
mmc: Fix re-probing with PM_POST_RESTORE notification
mmc: atmel-mci: fix multiblock SDIO transfers
mmc: at91_mci: fix multiblock SDIO transfers
|
|
The current code mis-calculates the ramoops header size, leading to an
overflow over the next record at best, or over a non-allocated region at
worst. Fix that calculation.
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Acked-by: Marco Stornelli <marco.stornelli@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6
* 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: intc: Initialize radix tree gfp mask explicitly.
sh: Fix up SH7201 clkfwk build.
sh: mach-se: Fix up SE7206 build.
sh: Fix up SH4-202 clkfwk build.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-2.6
* 'fbdev-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-2.6:
fbdev: sh_mobile_lcdc: increase maximum framebuffer size to support 1080p
video: imxfb: Fix the maximum value for yres
fb: fix overlapping test off-by-one.
fbdev: sh-mobile: retrieve and propagate display sizes from EDID
fbdev: sh-mobile: restore display size configuration
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
pata_cs5536: avoid implicit MSR API inclusion on x86-64
|
|
LCDC hardware can support 1920x1080 formats, adjust the driver to cover them.
Besides, instead of guessing some "reasonable" validity checks, only verify
values in .fb_check_var(), that we are sure, we cannot support.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
MX27 and MX25 have 10 bits in the YMAX field of LCDC Size Register.
Fix the maximum value for yres.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
We don't need or want MSR usage here, on x86-64.
x86-64 was disabled intentionally in Kconfig, but commit
9272dcc232b84ccb027d6861077934055d42764d changed that.
drivers/ata/pata_cs5536.c:47:1: warning: "rdmsr" redefined
In file included from arch/x86/include/asm/irqflags.h:60,
from include/linux/irqflags.h:15,
from arch/x86/include/asm/system.h:11,
from arch/x86/include/asm/processor.h:17,
from include/linux/prefetch.h:14,
from include/linux/list.h:7,
from include/linux/module.h:9,
from drivers/ata/pata_cs5536.c:33:
arch/x86/include/asm/paravirt.h:146:1: warning: this is the location of the previous definition
drivers/ata/pata_cs5536.c:48:1: warning: "wrmsr" redefined
arch/x86/include/asm/paravirt.h:154:1: warning: this is the location of the previous definition
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
|
|
GPEs with corresponding _Lxx/_Exx control methods need to be disabled
during initialization in case they have been enabled by the BIOS, so
that they don't fire up until they are enabled by acpi_update_gpes().
References: https://bugzilla.kernel.org/show_bug.cgi?id=25412
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits)
ipv4: dont create routes on down devices
epic100: hamachi: yellowfin: Fix skb allocation size
sundance: Fix oopses with corrupted skb_shared_info
Revert "ipv4: Allow configuring subnets as local addresses"
USB: mcs7830: return negative if auto negotiate fails
irda: prevent integer underflow in IRLMP_ENUMDEVICES
tcp: fix listening_get_next()
atl1c: Do not use legacy PCI power management
mac80211: fix mesh forwarding
MAINTAINERS: email address change
net: Fix range checks in tcf_valid_offset().
net_sched: sch_sfq: fix allot handling
hostap: remove netif_stop_queue from init
mac80211/rt2x00: add ieee80211_tx_status_ni()
typhoon: memory corruption in typhoon_get_drvinfo()
net: Add USB PID for new MOSCHIP USB ethernet controller MCS7832 variant
net_sched: always clone skbs
ipv6: Fragment locally generated tunnel-mode IPSec6 packets as needed.
netlink: fix gcc -Wconversion compilation warning
asix: add USB ID for Logitec LAN-GTJ U2A
...
|
|
Joel Soete reported oopses during pppoe over sundance NIC, caused by
a bug in skb allocation and dma mapping code, where skb_reserve()
bytes weren't taken into account. As a followup to the patch:
"sundance: Fix oopses with corrupted skb_shared_info" very similar
code is fixed here for three other drivers.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Cc: Joel Soete <soete.joel@scarlet.be>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Joel Soete reported oopses at the beginning of pppoe connections since
v2.6.35. After debugging the bug was found in sundance skb allocation
and dma mapping code, where skb_reserve() bytes aren't taken into
account. This is an old bug, only uncovered by some change in 2.6.35.
Initial debugging patch by: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: Joel Soete <soete.joel@scarlet.be>
Tested-by: Joel Soete <soete.joel@scarlet.be>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A recent patch has introduced a regression, whereby a second open of an
soc-camera video device breaks the running capture. This patch fixes this bug
by guaranteeing, that video buffers get initialised only during the first open
of the device node.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This reverts commit 3138b32d5e0998ba3cbd1c74bdc1887d74c5279b.
as it caused a crash upon battery removal:
https://bugzilla.kernel.org/show_bug.cgi?id=25302
Signed-off-by: Len Brown <len.brown@intel.com>
|
