| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging fixes from Greg KH:
"Here are a number of small staging tree and iio driver fixes. Nothing
major, just lots of little things"
* tag 'staging-3.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (34 commits)
iio:buffer_cb: Add missing iio_buffer_init()
iio: Prevent race between IIO chardev opening and IIO device free
iio: fix: Keep a reference to the IIO device for open file descriptors
iio: Stop sampling when the device is removed
iio: Fix crash when scan_bytes is computed with active_scan_mask == NULL
iio: Fix mcp4725 dev-to-indio_dev conversion in suspend/resume
iio: Fix bma180 dev-to-indio_dev conversion in suspend/resume
iio: Fix tmp006 dev-to-indio_dev conversion in suspend/resume
iio: iio_device_add_event_sysfs() bugfix
staging: iio: ade7854-spi: Fix return value
staging:iio:hmc5843: Fix measurement conversion
iio: isl29018: Fix uninitialized value
staging:iio:dummy fix kfifo_buf kconfig dependency issue if kfifo modular and buffer enabled for built in dummy driver.
iio: at91: fix adc_clk overflow
staging: line6: add bounds check in snd_toneport_source_put()
Staging: comedi: Fix dependencies for drivers misclassified as PCI
staging: r8188eu: Adjust RX gain
staging: r8188eu: Fix smatch warning in core/rtw_ieee80211.
staging: r8188eu: Fix smatch error in core/rtw_mlme_ext.c
staging: r8188eu: Fix Smatch off-by-one warning in hal/rtl8188e_hal_init.c
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of small USB fixes for 3.12-rc2.
One is a revert of a EHCI change that isn't quite ready for 3.12.
Others are minor things, gadget fixes, Kconfig fixes, and some quirks
and documentation updates.
All have been in linux-next for a bit"
* tag 'usb-3.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: pl2303: distinguish between original and cloned HX chips
USB: Faraday fotg210: fix email addresses
USB: fix typo in usb serial simple driver Kconfig
Revert "USB: EHCI: support running URB giveback in tasklet context"
usb: s3c-hsotg: do not disconnect gadget when receiving ErlySusp intr
usb: s3c-hsotg: fix unregistration function
usb: gadget: f_mass_storage: reset endpoint driver data when disabled
usb: host: fsl-mph-dr-of: Staticize local symbols
usb: gadget: f_eem: Staticize eem_alloc
usb: gadget: f_ecm: Staticize ecm_alloc
usb: phy: omap-usb3: Fix return value
usb: dwc3: gadget: avoid memory leak when failing to allocate all eps
usb: dwc3: remove extcon dependency
usb: gadget: add '__ref' for rndis_config_register() and cdc_config_register()
usb: dwc3: pci: add support for BayTrail
usb: gadget: cdc2: fix conversion to new interface of f_ecm
usb: gadget: fix a bug and a WARN_ON in dummy-hcd
usb: gadget: mv_u3d_core: fix violation of locking discipline in mv_u3d_ep_disable()
|
|
Move probe out of __init section and don't use platform_driver_probe
which cannot be used with deferred probing.
Since commit e9354576 ("gpiolib: Defer failed gpio requests by default")
and 04bf3011 ("regulator: Support driver probe deferral") this driver
might return -EPROBE_DEFER if a gpio_request or regulator_get fails.
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Move probe out of __init section and don't use platform_driver_probe
which cannot be used with deferred probing.
Since commit e9354576 ("gpiolib: Defer failed gpio requests by default")
this driver might return -EPROBE_DEFER if a gpio_request fails.
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Starting with UVD3 message and feedback buffers have their
own 256MB segment, so no need to force them into VRAM any more.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The tests are only usable if the acceleration engines have
been successfully initialized.
Based on an initial patch from: Alex Ivanov <gnidorah@p0n4ik.tk>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Allow user to change the number of IOs that are reserved by
bio-based DM's mempools by writing to this file:
/sys/module/dm_mod/parameters/reserved_bio_based_ios
The default value is RESERVED_BIO_BASED_IOS (16). The maximum allowed
value is RESERVED_MAX_IOS (1024).
Export dm_get_reserved_bio_based_ios() for use by DM targets and core
code. Switch to sizing dm-io's mempool and bioset using DM core's
configurable 'reserved_bio_based_ios'.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Frank Mayhar <fmayhar@google.com>
|
|
Allow user to change the number of IOs that are reserved by
request-based DM's mempools by writing to this file:
/sys/module/dm_mod/parameters/reserved_rq_based_ios
The default value is RESERVED_REQUEST_BASED_IOS (256). The maximum
allowed value is RESERVED_MAX_IOS (1024).
Export dm_get_reserved_rq_based_ios() for use by DM targets and core
code. Switch to sizing dm-mpath's mempool using DM core's configurable
'reserved_rq_based_ios'.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Frank Mayhar <fmayhar@google.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
|
|
Bio-based device mapper processing doesn't need larger mempools (like
request-based DM does), so lower the number of reserved entries for
bio-based operation. 16 was already used for bio-based DM's bioset
but mistakenly wasn't used for it's _io_cache.
Formalize difference between bio-based and request-based defaults by
introducing RESERVED_BIO_BASED_IOS and RESERVED_REQUEST_BASED_IOS.
(based on older code from Mikulas Patocka)
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Frank Mayhar <fmayhar@google.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
|
|
Fix issue where the block layer would stack the discard limits of the
pool's data device even if the "ignore_discard" pool feature was
specified.
The pool and thin device(s) still had discards disabled because the
QUEUE_FLAG_DISCARD request_queue flag wasn't set. But to avoid user
confusion when "ignore_discard" is used: both the pool device and the
thin device(s) have zeroes for all discard limits.
Also, always set discard_zeroes_data_unsupported in targets because they
should never advertise the 'discard_zeroes_data' capability (even if the
pool's data device supports it).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
|
|
This is a partial revert of c6cf7777a32da874fabec4fd1c2a579f0ba4e4dd.
We need to take into account the clk voltage dependencies of the
board. Not doing so can lead to stability issues on certain
boards if the clks exceed the levels in the dep tables.
DPM already takes that into account, so for optimal performance,
use DPM.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Filter out mclk and sclk levels higher than listed in the clk
voltage dependency tables. Supporting these clocks will require
additional driver tweaking that isn't supported yet.
See bug:
https://bugs.freedesktop.org/show_bug.cgi?id=68235
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Filter out mclk and sclk levels higher than listed in the clk
voltage dependency tables. Supporting these clocks will require
additional driver tweaking that isn't supported yet.
See bug:
https://bugs.freedesktop.org/show_bug.cgi?id=68235
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
filter out mclk and sclk levels higher than listed in the clk
voltage dependency tables. Supporting these clocks will require
additional driver tweaking that isn't supported yet.
See bug:
https://bugs.freedesktop.org/show_bug.cgi?id=68235
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Filter out mclk and sclk levels higher than listed in the clk
voltage dependency tables. Supporting these clocks will require
additional driver tweaking that isn't supported yet.
See bug:
https://bugs.freedesktop.org/show_bug.cgi?id=68235
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This patch adds a helper function to fetch the max clock
from the voltage clock dependecy tables. Clocks above that
level tend to be unstable and will require additional driver
tweaks in order to work properly.
This patch implemented the helper function to fetch the max clocks
from the dependency tables. The following patches implement the
per-asic clock filtering.
See bug:
https://bugs.freedesktop.org/show_bug.cgi?id=68235
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
I missed this when I fixed up this file.
Noticed-by: Mathias Fröhlich <Mathias.Froehlich@gmx.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Fix the linear range settings in commit 5ff26a14c3331
"regulator: wm831x-ldo: Convert to use linear ranges".
For wm831x_gp_ldo:
We have below equations for list voltage before converting to linear ranges:
sel <= 0xe:
volt = 0.9-1.6V in 50mV steps
sel <= 0x1f:
volt = 1.7-3.3V in 100mV steps
max_uV for the first linear range should be 1600000 rather than 1650000. Fix it.
For wm831x_aldo:
We have below equations for list voltage before converting to linear ranges:
sel <= 0xc:
volt = 1-1.6V in 50mV steps
sel <= 0x1f
volt = 1.7-3.5V in 100mV steps
max_uV for the first linear range should be 1600000 rather than 1650000. Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The some platforms (e.g., ARM) initializes their clocks as
late_initcalls for some unknown reason. So make sure
random_int_secret_init() is run after all of the late_initcalls are
run.
Cc: stable@vger.kernel.org
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
|
|
sizeof() is already size_t so there is no need to cast here. Generally,
casting inside the min() macro instead of using min_t() is considered
bad style.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Have pinconf_dbg_config_write() return a ssize_t. This fixes the following
compilation warning:
drivers/pinctrl/pinconf.c:617:2: warning: initialization from incompatible pointer type [enabled by default]
drivers/pinctrl/pinconf.c:617:2: warning: (near initialization for ‘pinconf_dbg_pinconfig_fops.write’) [enabled by default]
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
On 848xx PHY (10G-baseT), half-duplex was always advertised regardless of the
actual configuration. Change the 848xx duplex settings to advertise half-duplex
only if configured.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix Warpcore mode setting when active DAC (Direct Attached Cable) is detected.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
when 1G-optic module was plugged in, internal loopback test failed because the
driver used to check the optic module (with no need), and for 1G optic module,
the link speed was forced down to 1G, while the XMAC (10G MAC) was enabled.
This patch avoid accessing optic module in case internal loopback was selected,
and update the link speed in case 1G optic module was detected during init
stage.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Relocate bnx2x_disable_kr2 function, and use it to disable KR2 in case it is not
configured in order to clear it's configuration, otherwise the link may come up
at 20G instead of the requested 10G-KR. In addition, restart AN after
disabling KR2 as part of the KR2 work-around.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously, in case of KR link down, the driver would reset the PHY and restart
auto negotiation only when old Warpcore microcode was used (below D108).
This patch comes to generalize this by keep trying to restart KR link,
regardless of Warpcore microcode, since it was found that it solves another link
issue which source is a link-partner. As part of this change, the signal
detect is no longer a condition to apply the work-around to cover this new case.
Like before, as long as the link is down, AN will be restarted every 2 seconds.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull drm fixes from Dave Airlie:
- some small fixes for msm and exynos
- a regression revert affecting nouveau users with old userspace
- intel pageflip deadlock and gpu hang fixes, hsw modesetting hangs
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (22 commits)
Revert "drm: mark context support as a legacy subsystem"
drm/i915: Don't enable the cursor on a disable pipe
drm/i915: do not update cursor in crtc mode set
drm/exynos: fix return value check in lowlevel_buffer_allocate()
drm/exynos: Fix address space warnings in exynos_drm_fbdev.c
drm/exynos: Fix address space warning in exynos_drm_buf.c
drm/exynos: Remove redundant OF dependency
drm/msm: drop unnecessary set_need_resched()
drm/i915: kill set_need_resched
drm/msm: fix potential NULL pointer dereference
drm/i915/dvo: set crtc timings again for panel fixed modes
drm/i915/sdvo: Robustify the dtd<->drm_mode conversions
drm/msm: workaround for missing irq
drm/msm: return -EBUSY if bo still active
drm/msm: fix return value check in ERR_PTR()
drm/msm: fix cmdstream size check
drm/msm: hangcheck harder
drm/msm: handle read vs write fences
drm/i915/sdvo: Fully translate sync flags in the dtd->mode conversion
drm/i915: Use proper print format for debug prints
...
|
|
Commit a1bc260bb5f5d95da854be7898202d788e94448d ("gpio: clean up
gpio-ranges documentation") deprecated the #gpio-range-cells property.
Replace its usage with a hardcoded value in the gpio-rcar driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Ben Hutchings says:
====================
Daniel Pieczko fixed two bugs in reset handling that particularly
affected the new SFC9120 controller.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently DT compatibility strings of both types can be found in the kernel
sources: <unit>-<soc> and <soc>-<unit>, whereas a unique format should be
followed and the former one is preferred. This patch converts the SDHI
MMC driver and its users to the common standard. This is safe for now, since
ATM no real products are using this driver with DT.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Chris Ball <cjb@laptop.org>
[Removed r8a7740.dtsi portion as it is not applicable]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Make sure to properly initialize the IIO buffer data structure.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Set the IIO device as the parent for the character device
We need to make sure that the IIO device is not freed while the character device
exists, otherwise the freeing of the IIO device might race against the file open
callback. Do this by setting the character device's parent to the IIO device,
this will cause the character device to grab a reference to the IIO device and
only release it once the character device itself has been removed.
Also move the registration of the character device before the registration of
the IIO device to avoid the (rather theoretical case) that the IIO device is
already freed again before we can add the character device and grab a reference
to the IIO device.
We also need to move the call to cdev_del() from iio_dev_release() to
iio_device_unregister() (where it should have been in the first place anyway) to
avoid a reference cycle. As iio_dev_release() is only called once all reference
are dropped, but the character device holds a reference to the IIO device.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Make sure that the IIO device is not freed while we still have file descriptors
for it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Make sure to stop sampling when the device is removed, otherwise it will
continue to sample forever.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
if device has available_scan_masks set and the buffer is enabled without
any scan_elements enabled, in a NULL pointer is dereferenced in iio_compute_scan_bytes()
[ 18.993713] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 19.002593] pgd = debd4000
[ 19.005432] [00000000] *pgd=9ebc0831, *pte=00000000, *ppte=00000000
[ 19.012329] Internal error: Oops: 17 [#1] PREEMPT ARM
[ 19.017639] Modules linked in:
[ 19.020843] CPU: 0 Not tainted (3.9.11-00036-g75c888a-dirty #207)
[ 19.027587] PC is at _find_first_bit_le+0xc/0x2c
[ 19.032440] LR is at iio_compute_scan_bytes+0x2c/0xf4
[ 19.037719] pc : [<c021dc60>] lr : [<c03198d0>] psr: 200d0013
[ 19.037719] sp : debd9ed0 ip : 00000000 fp : 000802bc
[ 19.049713] r10: 00000000 r9 : 00000000 r8 : deb67250
[ 19.055206] r7 : 00000000 r6 : 00000000 r5 : 00000000 r4 : deb67000
[ 19.062011] r3 : de96ec00 r2 : 00000000 r1 : 00000004 r0 : 00000000
[ 19.068847] Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
[ 19.076324] Control: 10c5387d Table: 9ebd4019 DAC: 00000015
problem is the rollback code in iio_update_buffers(), old_mask may be NULL (e.g. on first
call)
I'm not too confident about the fix; works for me...
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
dev_to_iio_dev() is a false friend
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
dev_to_iio_dev() is a false friend
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Oleksandr Kravchenko <o.v.kravchenko@globallogic.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
dev_to_iio_dev() is a false friend
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
1) Four fixes for cpufreq regressions introduced by the changes that
removed Device Tree parsing for CPU device nodes from cpufreq
drivers from Sudeep KarkadaNagesha.
2) Two fixes for recent cpufreq regressions introduced by changes
related to the preservation of sysfs attributes over system
suspend/resume cycles from Viresh Kumar.
3) Fix for ACPI-based wakeup signaling in the PCI subsystem that
fails to stop PME polling for devices put into the D3cold power
state from Rafael J Wysocki.
4) Fix for bad interactions between cpufreq and udev on systems
supporting intel_pstate where acpi-cpufreq is available as well
from Yinghai Lu.
* tag 'pm+acpi-3.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: return EEXIST instead of EBUSY for second registering
PCI / ACPI / PM: Clear pme_poll for devices in D3cold on wakeup
ARM: shmobile: change dev_id to cpu0 while registering cpu clock
ARM: i.MX: change dev_id to cpu0 while registering cpu clock
cpufreq: imx6q-cpufreq: assign cpu_dev correctly to cpu0 device
cpufreq: cpufreq-cpu0: assign cpu_dev correctly to cpu0 device
cpufreq: unlock correct rwsem while updating policy->cpu
cpufreq: Clear policy->cpus bits in __cpufreq_remove_dev_finish()
|
|
Pull vhost updates from Michael Tsirkin:
"vhost: minor changes on top of 3.12-rc1
This fixes module loading for vhost-scsi, and tweaks locking in vhost
core a bit. Both of these are not exactly release blockers but it's
early in the cycle so I think it's a good idea to apply them now"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vhost-scsi: whitespace tweak
vhost/scsi: use vmalloc for order-10 allocation
vhost: wake up worker outside spin_lock
|
|
Prevent NULL pointer dereference in case when radeon_ring_fini() did it's job.
Reading of r100_cp_ring_info and radeon_ring_gfx debugfs entries will lead to a KP if ring buffer was deallocated, e.g. on failed ring test.
Seen on PA-RISC machine having "radeon: ring test failed (scratch(0x8504)=0xCAFEDEAD)" issue.
v2: agd5f: add some parens around ring->ready check
Signed-off-by: Alex Ivanov <gnidorah@p0n4ik.tk>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
There are multiple valid values, not just 0 or 1. Required
to properly support 2D tiling in the userspace drivers.
Cc: stable@vger.kernel.org
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The old implementation was heavy on str* functions and sprintf calls.
This version is more manual, but faster.
Profiling just the printing of a 3 char CAN-id resulted in 60 instructions
for the manual method and over 2000 for the sprintf method. Bear in
mind the profiling was done against libc and not the kernel sprintf.
Together with this rewrite an issue with sending and receiving of RTR frames
has been fixed by Oliver for the cases that the DLC is not zero.
Signed-off-by: Andre Naujoks <nautsch2@gmail.com>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The locking is needed, since the the internal buffer for the CAN frames is
changed during the wakeup call. This could cause buffer inconsistencies
under high loads, especially for the outgoing short CAN packet skbuffs.
The needed locks led to deadlocks before commit
"5ede52538ee2b2202d9dff5b06c33bfde421e6e4 tty: Remove extra wakeup from pty
write() path", which removed the direct callback to the wakeup function from the
tty layer.
As slcan.c is based on slip.c the issue in the original code is fixed, too.
Signed-off-by: Andre Naujoks <nautsch2@gmail.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tx and rx urbs are not deallocated if something goes wrong in peak_usb_start().
The patch fixes error handling to deallocate all the resources.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The string is encoded from the MSB to the LSB of the register.
Cc: stable@vger.kernel.org
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Newer versions of gcc seem to wander off into the weeds
when dealing with variable sizes arrays in structs.
Rather than indexing the arrays, use pointer arithmetic.
Fix up spread spectrum tables.
See bugs:
https://bugs.freedesktop.org/show_bug.cgi?id=66932
https://bugs.freedesktop.org/show_bug.cgi?id=66972
https://bugs.freedesktop.org/show_bug.cgi?id=66945
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
If the user has forced the driver to use the internal GPU gart
rather than AGP on an AGP card, force the buffers to vram
as well.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Tested-by: Dieter Nützel <Dieter@nuetzel-hh.de>
Cc: stable@vger.kernel.org
|
|
From Jason Cooper, mvebu fixes for v3.12:
- mvebu
- fix reference leaks by adding of_node_put()
- update Armada XP DT clock properties to restore booting
- kirkwood
- add missing reg property for cpu@0
- fix typo in address of second XOR engine
* tag 'fixes-3.12' of git://git.infradead.org/linux-mvebu:
ARM: kirkwood: Fix address of second XOR engine
ARM: mvebu: Add clock properties to Armada XP timer node
ARM: mvebu: Add the reference 25 MHz fixed-clock to Armada XP
ARM: Kirkwood: Add missing DT reg property to cpu@0
bus: mvebu: add missing of_node_put() to fix reference leak
ARM: mvebu: add missing of_node_put() to fix reference leak
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The SFC9120 MC firmware often takes longer than 20ms to reboot and
update the warm boot count in BIU_MC_SFT_STATUS_REG. A timeout of
250ms is very generous for an MC reboot.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
